| Age | Commit message (Collapse) | Author |
|---|
|
Since umr tool can't handle bracket, change uvd ring name convention.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Support manual LCLK DPM level switch on Vega20.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When a job is timeout, try to print the related process information
for debugging
Signed-off-by: Trigger Huang <Trigger.Huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Configure PCIE_CI_CNTL to work around a hw bug that affects
some multi-GPU compute workloads.
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Configure PCIE_CI_CNTL to work around a hw bug that affects
some multi-GPU compute workloads.
Acked-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Changed "avaiable" to "available" and "interupt" to "interrupt".
Signed-off-by: Jona Crasselt <jona.crasselt@fau.de>
Signed-off-by: Felix Windsheimer <felix.windsheimer@fau.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes: ba94c753ccb4 ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When both regular IO and resync IO happen at the same time,
and if we also need to split regular. Then we can see tasks
hang due to barrier.
1. resync thread
[ 1463.757205] INFO: task md1_resync:5215 blocked for more than 480 seconds.
[ 1463.757207] Not tainted 4.19.5-1-default #1
[ 1463.757209] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1463.757212] md1_resync D 0 5215 2 0x80000000
[ 1463.757216] Call Trace:
[ 1463.757223] ? __schedule+0x29a/0x880
[ 1463.757231] ? raise_barrier+0x8d/0x140 [raid10]
[ 1463.757236] schedule+0x78/0x110
[ 1463.757243] raise_barrier+0x8d/0x140 [raid10]
[ 1463.757248] ? wait_woken+0x80/0x80
[ 1463.757257] raid10_sync_request+0x1f6/0x1e30 [raid10]
[ 1463.757265] ? _raw_spin_unlock_irq+0x22/0x40
[ 1463.757284] ? is_mddev_idle+0x125/0x137 [md_mod]
[ 1463.757302] md_do_sync.cold.78+0x404/0x969 [md_mod]
[ 1463.757311] ? wait_woken+0x80/0x80
[ 1463.757336] ? md_rdev_init+0xb0/0xb0 [md_mod]
[ 1463.757351] md_thread+0xe9/0x140 [md_mod]
[ 1463.757358] ? _raw_spin_unlock_irqrestore+0x2e/0x60
[ 1463.757364] ? __kthread_parkme+0x4c/0x70
[ 1463.757369] kthread+0x112/0x130
[ 1463.757374] ? kthread_create_worker_on_cpu+0x40/0x40
[ 1463.757380] ret_from_fork+0x3a/0x50
2. regular IO
[ 1463.760679] INFO: task kworker/0:8:5367 blocked for more than 480 seconds.
[ 1463.760683] Not tainted 4.19.5-1-default #1
[ 1463.760684] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1463.760687] kworker/0:8 D 0 5367 2 0x80000000
[ 1463.760718] Workqueue: md submit_flushes [md_mod]
[ 1463.760721] Call Trace:
[ 1463.760731] ? __schedule+0x29a/0x880
[ 1463.760741] ? wait_barrier+0xdd/0x170 [raid10]
[ 1463.760746] schedule+0x78/0x110
[ 1463.760753] wait_barrier+0xdd/0x170 [raid10]
[ 1463.760761] ? wait_woken+0x80/0x80
[ 1463.760768] raid10_write_request+0xf2/0x900 [raid10]
[ 1463.760774] ? wait_woken+0x80/0x80
[ 1463.760778] ? mempool_alloc+0x55/0x160
[ 1463.760795] ? md_write_start+0xa9/0x270 [md_mod]
[ 1463.760801] ? try_to_wake_up+0x44/0x470
[ 1463.760810] raid10_make_request+0xc1/0x120 [raid10]
[ 1463.760816] ? wait_woken+0x80/0x80
[ 1463.760831] md_handle_request+0x121/0x190 [md_mod]
[ 1463.760851] md_make_request+0x78/0x190 [md_mod]
[ 1463.760860] generic_make_request+0x1c6/0x470
[ 1463.760870] raid10_write_request+0x77a/0x900 [raid10]
[ 1463.760875] ? wait_woken+0x80/0x80
[ 1463.760879] ? mempool_alloc+0x55/0x160
[ 1463.760895] ? md_write_start+0xa9/0x270 [md_mod]
[ 1463.760904] raid10_make_request+0xc1/0x120 [raid10]
[ 1463.760910] ? wait_woken+0x80/0x80
[ 1463.760926] md_handle_request+0x121/0x190 [md_mod]
[ 1463.760931] ? _raw_spin_unlock_irq+0x22/0x40
[ 1463.760936] ? finish_task_switch+0x74/0x260
[ 1463.760954] submit_flushes+0x21/0x40 [md_mod]
So resync io is waiting for regular write io to complete to
decrease nr_pending (conf->barrier++ is called before waiting).
The regular write io splits another bio after call wait_barrier
which call nr_pending++, then the splitted bio would continue
with raid10_write_request -> wait_barrier, so the splitted bio
has to wait for barrier to be zero, then deadlock happens as
follows.
resync io regular io
raise_barrier
wait_barrier
generic_make_request
wait_barrier
To resolve the issue, we need to call allow_barrier to decrease
nr_pending before generic_make_request since regular IO is not
issued to underlying devices, and wait_barrier is called again
to ensure no internal IO happening.
Fixes: fc9977dd069e ("md/raid10: simplify the splitting of requests.")
Reported-and-tested-by: Siniša Bandin <sinisa@4net.rs>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Both raid10_read_request and raid10_write_request share
the same code at the beginning of them, so introduce
regular_request_wait to clean up code, and call it in
both request functions.
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
mempool_destroy() can handle NULL pointer correctly,
so there is no need to check NULL pointer before calling
mempool_destroy().
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/md/md.c: In function 'md_integrity_add_rdev':
drivers/md/md.c:2149:24: warning:
variable 'bi_rdev' set but not used [-Wunused-but-set-variable]
It not used any more after commit
1501efadc524 ("md/raid: only permit hot-add of compatible integrity profiles")
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Clang warns when an implicit conversion is done between enumerated
types:
drivers/block/drbd/drbd_state.c:708:8: warning: implicit conversion from
enumeration type 'enum drbd_ret_code' to different enumeration type
'enum drbd_state_rv' [-Wenum-conversion]
rv = ERR_INTR;
~ ^~~~~~~~
drbd_request_detach_interruptible's only call site is in the return
statement of adm_detach, which returns an int. Change the return type of
drbd_request_detach_interruptible to match, silencing Clang's warning.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
And also re-enable partial-zero-out + discard aligned.
With the introduction of REQ_OP_WRITE_ZEROES,
we started to use that for both WRITE_ZEROES and DISCARDS,
hoping that WRITE_ZEROES would "do what we want",
UNMAP if possible, zero-out the rest.
The example scenario is some LVM "thin" backend.
While an un-allocated block on dm-thin reads as zeroes, on a dm-thin
with "skip_block_zeroing=true", after a partial block write allocated
that block, that same block may well map "undefined old garbage" from
the backends on LBAs that have not yet been written to.
If we cannot distinguish between zero-out and discard on the receiving
side, to avoid "undefined old garbage" to pop up randomly at later times
on supposedly zero-initialized blocks, we'd need to map all discards to
zero-out on the receiving side. But that would potentially do a full
alloc on thinly provisioned backends, even when the expectation was to
unmap/trim/discard/de-allocate.
We need to distinguish on the protocol level, whether we need to guarantee
zeroes (and thus use zero-out, potentially doing the mentioned full-alloc),
or if we want to put the emphasis on discard, and only do a "best effort
zeroing" (by "discarding" blocks aligned to discard-granularity, and zeroing
only potential unaligned head and tail clippings to at least *try* to
avoid "false positives" in an online-verify later), hoping that someone
set skip_block_zeroing=false.
For some discussion regarding this on dm-devel, see also
https://www.mail-archive.com/dm-devel%40redhat.com/msg07965.html
https://www.redhat.com/archives/dm-devel/2018-January/msg00271.html
For backward compatibility, P_TRIM means zero-out, unless the
DRBD_FF_WZEROES feature flag is agreed upon during handshake.
To have upper layers even try to submit WRITE ZEROES requests,
we need to announce "efficient zeroout" independently.
We need to fixup max_write_zeroes_sectors after blk_queue_stack_limits():
if we can handle "zeroes" efficiently on the protocol,
we want to do that, even if our backend does not announce
max_write_zeroes_sectors itself.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If you try to promote a Secondary while connected to a Primary
and allow-two-primaries is NOT set, we will wait for "ping-timeout"
to give this node a chance to detect a dead primary,
in case the cluster manager noticed faster than we did.
But if we then are *still* connected to a Primary,
we fail (after an additional timeout of ping-timout).
This change skips the spurious second timeout.
Most people won't notice really,
since "ping-timeout" by default is half a second.
But in some installations, ping-timeout may be 10 or 20 seconds or more,
and spuriously delaying the error return becomes annoying.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
emma: "Unexpected data packet AuthChallenge (0x0010)"
ava: "expected AuthChallenge packet, received: ReportProtocol (0x000b)"
"Authentication of peer failed, trying again."
Pattern repeats.
There is no point in retrying the handshake,
if we expect to receive an AuthChallenge,
but the peer is not even configured to expect or use a shared secret.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
print_st_err() is defined with its 4th argument taking an
'enum drbd_state_rv' but its prototype use an int for it.
Fix this by using 'enum drbd_state_rv' in the prototype too.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If peers are "simultaneously" told to disconnect from each other,
either explicitly, or implicitly by taking down the resource,
with bad timing, one side may see its disconnect "fail" with
a result of "state change failed by peer", and interpret this as
"please oudate yourself".
Try to catch this by checking for current connection status,
and possibly retry as local-only state change instead.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
"suspending" IO is overloaded.
It can mean "do not allow new requests" (obviously),
but it also may mean "must not complete pending IO",
for example while the fencing handlers do their arbitration.
When adjusting disk options, we suspend io (disallow new requests), then
wait for the activity-log to become unused (drain all IO completions),
and possibly replace it with a new activity log of different size.
If the other "suspend IO" aspect is active, pending IO completions won't
happen, and we would block forever (unkillable drbdsetup process).
Fix this by skipping the activity log adjustment if the "al-extents"
setting did not change. Also, in case it did change, fail early without
blocking if it looks like we would block forever.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Multiple failure scenario:
a) all good
Connected Primary/Secondary UpToDate/UpToDate
b) lose disk on Primary,
Connected Primary/Secondary Diskless/UpToDate
c) continue to write to the device,
changes only make it to the Secondary storage.
d) lose disk on Secondary,
Connected Primary/Secondary Diskless/Diskless
e) now try to re-attach on Primary
This would have succeeded before, even though that is clearly the
wrong data set to attach to (missing the modifications from c).
Because we only compared our "effective" and the "to-be-attached"
data generation uuid tags if (device->state.conn < C_CONNECTED).
Fix: change that constraint to (device->state.pdsk != D_UP_TO_DATE)
compare the uuids, and reject the attach.
This patch also tries to improve the reverse scenario:
first lose Secondary, then Primary disk,
then try to attach the disk on Secondary.
Before this patch, the attach on the Secondary succeeds, but since commit
drbd: disconnect, if the wrong UUIDs are attached on a connected peer
the Primary will notice unsuitable data, and drop the connection hard.
Though unfortunately at a point in time during the handshake where
we cannot easily abort the attach on the peer without more
refactoring of the handshake.
We now reject any attach to "unsuitable" uuids,
as long as we can see a Primary role,
unless we already have access to "good" data.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we would reject a new handshake, if the peer had attached first,
and then connected, we should force disconnect if the peer first connects,
and only then attaches.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If we attach a (consistent) backing device,
which knows about a last-agreed effective size,
and that effective size is *larger* than the currently requested size,
we refused to attach with ERR_DISK_TOO_SMALL
Failure: (111) Low.dev. smaller than requested DRBD-dev. size.
which is confusing to say the least.
This patch changes the error code in that case to ERR_IMPLICIT_SHRINK
Failure: (170) Implicit device shrinking not allowed. See kernel log.
additional info from kernel:
To-be-attached device has last effective > current size, and is consistent
(9999 > 7777 sectors). Refusing to attach.
It also allows to attach with an explicit size.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
With "on-no-data-accessible suspend-io", DRBD requires the next attach
or connect to be to the very same data generation uuid tag it lost last.
If we first lost connection to the peer,
then later lost connection to our own disk,
we would usually refuse to re-connect to the peer,
because it presents the wrong data set.
However, if the peer first connects without a disk,
and then attached its disk, we accepted that same wrong data set,
which would be "unexpected" by any user of that DRBD
and cause "undefined results" (read: very likely data corruption).
The fix is to forcefully disconnect as soon as we notice that the peer
attached to the "wrong" dataset.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
During handshake, if we are diskless ourselves, we used to accept any size
presented by the peer.
Which could be zero if that peer was just brought up and connected
to us without having a disk attached first, in which case both
peers would just "flip" their volume sizes.
Now, even a diskless node will ignore "zero" sizes
presented by a diskless peer.
Also a currently Diskless Primary will refuse to shrink during handshake:
it may be frozen, and waiting for a "suitable" local disk or peer to
re-appear (on-no-data-accessible suspend-io). If the peer is smaller
than what we used to be, it is not suitable.
The logic for a diskless node during handshake is now supposed to be:
believe the peer, if
- I don't have a current size myself
- we agree on the size anyways
- I do have a current size, am Secondary, and he has the only disk
- I do have a current size, am Primary, and he has the only disk,
which is larger than my current size
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Previously, some implicit resizes that happend during handshake
have not been reported as prominently as explicit resize.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
So far there was the possibility that we called
genlmsg_new(GFP_NOIO)/mutex_lock() while holding an rcu_read_lock().
This included cases like:
drbd_sync_handshake (acquire the RCU lock)
drbd_asb_recover_1p
drbd_khelper
drbd_bcast_event
genlmsg_new(GFP_NOIO) --> may sleep
drbd_sync_handshake (acquire the RCU lock)
drbd_asb_recover_1p
drbd_khelper
notify_helper
genlmsg_new(GFP_NOIO) --> may sleep
drbd_sync_handshake (acquire the RCU lock)
drbd_asb_recover_1p
drbd_khelper
notify_helper
mutex_lock --> may sleep
While using GFP_ATOMIC whould have been possible in the first two cases,
the real fix is to narrow the rcu_read_lock.
Reported-by: Jia-Ju Bai <baijiaju1990@163.com>
Reviewed-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Roland Kammerer <roland.kammerer@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address 00000286
pgd = d8754000
[00000286] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task: dc44cac0 ti: d4a38000 task.ti: d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<c02bdc50>] lr : [<bf916b78>] psr: 20000013
sp : d4a39b88 ip : 00000000 fp : 00000001
r10: 00000000 r9 : 1d3bc000 r8 : 00000dc0
r7 : 000080d0 r6 : d4a38000 r5 : dd401b00 r4 : 00000286
r3 : 00000000 r2 : d4a39ba0 r1 : 000080d0 r0 : dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5787d Table: 5a75406a DAC: 00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<c02bdc50>] (kmem_cache_alloc) from [<bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<bf916b78>] (ath10k_sta_state [ath10k_core]) from [<bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<bf88634c>] (ieee80211_add_station [mac80211]) from [<bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<bf83f3c4>] (nl80211_new_station [cfg80211]) from [<bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<bf6c4040>] (extack_doit [compat]) from [<c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<c05c285c>] (genl_rcv_msg) from [<c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<c05c1d98>] (netlink_rcv_skb) from [<c05c25d4>] (genl_rcv+0x20/0x34)
[<c05c25d4>] (genl_rcv) from [<c05c1750>] (netlink_unicast+0x11c/0x204)
[<c05c1750>] (netlink_unicast) from [<c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<c05c1be0>] (netlink_sendmsg) from [<c0587e90>] (sock_sendmsg+0x70/0x84)
[<c0587e90>] (sock_sendmsg) from [<c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<c058970c>] (___sys_sendmsg.part.3) from [<c058a594>] (__sys_sendmsg+0x4c/0x70)
[<c058a594>] (__sys_sendmsg) from [<c0208c80>] (ret_fast_syscall+0x0/0x44)
Code: ebfffec1 e1a04000 ea00001b e5953014 (e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes: a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea95 ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Only the mount namespace code that implements mount(2) should be using the
MS_* flags. Suppress them inside the kernel unless uapi/linux/mount.h is
included.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: David Howells <dhowells@redhat.com>
|
|
The top word of the constant can only have bits set if sign
extension set it to all-1, therefore we don't really have to
mask the top half of the register. We can just OR it into
the result as is.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The verifier will now understand the JSET instruction, so don't
mark the dead branch in the JIT as noop. We won't generate any
code, anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
For a little better performance on faster machines and faster link
speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Older firmware only supports 16-bit flow handle, because of which the
number of flows that can be offloaded can’t scale beyond a point.
Newer firmware supports 64-bit flow handle enabling the host to scale
upto millions of flows. With the new 64-bit flow handle support, driver
has to query flow stats in a different way compared to the older approach.
This patch adds support for 64-bit flow handle and new way to query
flow stats.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If RDMA is supported on the 57500 chip, increase context memory
allocations for the resources used by RDMA.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the new functions bnxt_alloc_ctx_pg_tbls()/bnxt_free_ctx_pg_tbls()
to allocate and free pages for context memory. The new functions
will handle the different levels of paging support and allocate/free
the pages accordingly using the existing functions.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To support level 2 context page memory structures, enhance the
bnxt_ring_mem_info structure with a "depth" field to specify the page
level and add a flag to specify using full pages for L1 and L2 page
tables. This is needed to support RDMA functionality on 57500 chips
since RDMA requires more context memory.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Earlier, some of the firmware commands (ex: CFA_FLOW_*) which are processed
by KONG processor were sent to the CHIMP processor from the host. This
approach was taken as there was no direct message channel to KONG.
CHIMP in turn used to send them to KONG. Newer firmware supports a new
message channel which the host can send messages directly to the KONG
processor.
This patch adds support for required changes needed in the driver
to support direct KONG message channel. This speeds up flow related
messages sent to the firmware for CLS_FLOWER offload.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These routines will be enhanced in the subsequent patch to
return the 2nd firmware comm. channel's hwrm response address &
sequence id respectively.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Typecast hwrm_cmd_resp_addr to (u8 *) from (void *) before doing
arithmetic.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
