| Age | Commit message (Collapse) | Author |
|---|
|
No need for it with devm_platform_ioremap_resource. Simplifies probe
slightly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241003214508.121107-1-rosenp@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
The Apple A8X SoC seems to be slowest at resetting, taking up to around
125ms to reset. Wait 150ms to be safe here.
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241001170018.20139-3-towinchenmi@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Although there is an existing code comment about flushing the writes,
writes were not actually being flushed.
Actually flush the writes by changing readl_relaxed() to readl().
Fixes: 4ed224aeaf661 ("watchdog: Add Apple SoC watchdog driver")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Nick Chan <towinchenmi@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20241001170018.20139-2-towinchenmi@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
The STM32MP15xx IWDG adds registers which permit this IP to generate
pretimeout interrupt. This interrupt can also be used to wake the CPU
from suspend. Implement support for generating this interrupt and let
userspace configure the pretimeout. In case the pretimeout is not
configured by user, set pretimeout to 3/4 of the WDT timeout cycle.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Tested-by: Clément Le Goffic <clement.legoffic@foss.st.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240415134903.8084-1-marex@denx.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
i2c_device_id::driver_data to 0
These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240920153430.503212-18-u.kleine-koenig@baylibre.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
In the current implementation, the value of max_hw_heartbeat_ms is set
to the timeout period expressed in milliseconds and fails to verify if
the close window percentage exceeds the maximum value that the hardware
supports.
1. Calculate max_hw_heartbeat_ms based on input clock frequency.
2. Update frequency check to require a minimum frequency of 1Mhz.
3. Limit the close and open window percent to hardware supported value
to avoid truncation.
4. If the user input timeout exceeds the maximum timeout supported, use
only open window and the framework supports the higher timeouts.
Fixes: 12984cea1b8c ("watchdog: xilinx_wwdt: Add Versal window watchdog support")
Signed-off-by: Harini T <harini.t@amd.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240913113230.1939373-1-harini.t@amd.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Commit da23b6faa8bf ("watchdog: iTCO: Add support for Cannon Lake
PCH iTCO") does not mask NMI_NOW bit during TCO1_CNT register's
value comparison for update_no_reboot_bit() call causing following
failure:
...
iTCO_vendor_support: vendor-support=0
iTCO_wdt iTCO_wdt: unable to reset NO_REBOOT flag, device
disabled by hardware/BIOS
...
and this can lead to unexpected NMIs later during regular
crashkernel's workflow because of watchdog probe call failures.
This change masks NMI_NOW bit for TCO1_CNT register values to
avoid unexpected NMI_NOW bit inversions.
Fixes: da23b6faa8bf ("watchdog: iTCO: Add support for Cannon Lake PCH iTCO")
Signed-off-by: Oleksandr Ocheretnyi <oocheret@cisco.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20240913191403.2560805-1-oocheret@cisco.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Correctly spelled comments make it easier for the reader to understand
the code.
Fix typos:
'hearbeat' -> 'heartbeat',
'retrigggers' -> 'retriggers',
'funtions' -> 'functions',
'Resgister' -> 'Register'.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Reviewed-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Link: https://lore.kernel.org/r/20240923075016.2439774-1-yanzhen@vivo.com
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
|
|
Implement event sending for IB device rename and IB device
port associated netdevice rename.
In iproute2, rdma monitor displays the IB device name, port
and the netdevice name when displaying event info. Since
users can modiy these names, we track and notify on renaming
events.
Note: In order to receive netdevice rename events, drivers
must use the ib_device_set_netdev() API when attaching net
devices to IB devices.
$ rdma monitor
$ rmmod mlx5_ib
[UNREGISTER] dev 1 rocep8s0f1
[UNREGISTER] dev 0 rocep8s0f0
$ modprobe mlx5_ib
[REGISTER] dev 2 mlx5_0
[NETDEV_ATTACH] dev 2 mlx5_0 port 1 netdev 4 eth2
[REGISTER] dev 3 mlx5_1
[NETDEV_ATTACH] dev 3 mlx5_1 port 1 netdev 5 eth3
[RENAME] dev 2 rocep8s0f0
[RENAME] dev 3 rocep8s0f1
$ devlink dev eswitch set pci/0000:08:00.0 mode switchdev
[UNREGISTER] dev 2 rocep8s0f0
[REGISTER] dev 4 mlx5_0
[NETDEV_ATTACH] dev 4 mlx5_0 port 30 netdev 4 eth2
[RENAME] dev 4 rdmap8s0f0
$ echo 4 > /sys/class/net/eth2/device/sriov_numvfs
[NETDEV_ATTACH] dev 4 rdmap8s0f0 port 2 netdev 7 eth4
[NETDEV_ATTACH] dev 4 rdmap8s0f0 port 3 netdev 8 eth5
[NETDEV_ATTACH] dev 4 rdmap8s0f0 port 4 netdev 9 eth6
[NETDEV_ATTACH] dev 4 rdmap8s0f0 port 5 netdev 10 eth7
[REGISTER] dev 5 mlx5_0
[NETDEV_ATTACH] dev 5 mlx5_0 port 1 netdev 11 eth8
[REGISTER] dev 6 mlx5_1
[NETDEV_ATTACH] dev 6 mlx5_1 port 1 netdev 12 eth9
[RENAME] dev 5 rocep8s0f0v0
[RENAME] dev 6 rocep8s0f0v1
[REGISTER] dev 7 mlx5_0
[NETDEV_ATTACH] dev 7 mlx5_0 port 1 netdev 13 eth10
[RENAME] dev 7 rocep8s0f0v2
[REGISTER] dev 8 mlx5_0
[NETDEV_ATTACH] dev 8 mlx5_0 port 1 netdev 14 eth11
[RENAME] dev 8 rocep8s0f0v3
$ ip link set eth2 name myeth2
[NETDEV_RENAME] netdev 4 myeth2
$ ip link set eth1 name myeth1
** no events received, because eth1 is not attached to
an IB device **
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Link: https://patch.msgid.link/093c978ef2766fd3ab4ff8798eeb68f2f11582f6.1730367038.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Implement the device API for ufile_hw_cleanup operation, which
iterates over the ufile uobjects lists, and attempts to destroy
DevX QPs, by issuing up to 8 commands in parallel.
This function is responsible only for cleaning the FW resources of the
QP, and doesn't necessarily cleanup all of its resources.
Hence the normal serialized cleanup flow is still executed after it
in __uverbs_cleanup_ufile() to cleanup the remaining resources and
handle the cleanup of SW objects.
In order to avoid double cleanup for the FW resources, new DevX flag
was added DEVX_OBJ_FLAGS_HW_FREED, which marks the object's FW resources
as already freed.
Since QP destruction is the most time-consuming operation in FW,
parallelizing it reduces the cleanup time of applications that use
DevX QPs.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/2f82675d0412542cba1c47a6b86f589521ae41e1.1730373303.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
In light of the previous commit, make the ib_uverbs_file accessible to
drivers by moving its definition to uverbs_types.h, to allow drivers to
freely access the struct argument and create a personalized cleanup flow.
For the same reason expose uverbs_try_lock_object function to allow driver
to safely access the uverbs objects.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/29b718e0dca35daa5f496320a39284fc1f5a1722.1730373303.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add a driver operation to allow preemptive cleanup of ufile HW resources
before the standard ufile cleanup flow begins. Thus, expediting the
final cleanup phase which leads to fast teardown overall.
This allows the use of driver specific clean up procedures to make the
cleanup process more efficient.
Signed-off-by: Patrisious Haddad <phaddad@nvidia.com>
Link: https://patch.msgid.link/cabe00d75132b5732cb515944e3c500a01fb0b4a.1730373303.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Fix a race condition when creating a lag bond in active backup
mode where after the bond creation the backup slave was
attached to the IB device, instead of the active slave.
This caused stale entries in the GID table, as the gid updating
mechanism relies on ib_device_get_netdev(), which would return
the backup slave.
Send an MLX5_DRIVER_EVENT_ACTIVE_BACKUP_LAG_CHANGE_LOWERSTATE
event when activating the lag, additionally to when modifying
the lag. This ensures that eventually the active netdevice is
stored in the bond IB device.
When handling this event remove the GIDs of the previously
attached netdevice in this port and rescan the GIDs of the
newly attached netdevice.
This ensures that eventually the active slave netdevice is
correctly stored in the IB device port. While there might be
a brief moment where the backup slave GIDs appear in the GID
table, it will eventually stabilize with the correct GIDs
(of the bond and the active slave).
Fixes: 8d159eb2117b ("RDMA/mlx5: Use IB set_netdev and get_netdev functions")
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Link: https://patch.msgid.link/91fc2cb24f63add266a528c1c702668a80416d9f.1730381292.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
rdma_roce_rescan_port() scans all network devices in
the system and adds the gids if relevant to the RoCE device
port. When not in bonding mode it adds the GIDs of the
netdevice in this port. When in bonding mode it adds the
GIDs of both the port's netdevice and the bond master
netdevice.
Export roce_del_all_netdev_gids(), which removes all GIDs
associated with a specific netdevice for a given port.
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Link: https://patch.msgid.link/674d498da4637a1503ff1367e28bd09ff942fd5e.1730381292.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Move dev_put() call to occur directly after the blocking
notifier, instead of within the event handler.
Fixes: 8d159eb2117b ("RDMA/mlx5: Use IB set_netdev and get_netdev functions")
Signed-off-by: Chiara Meiohas <cmeiohas@nvidia.com>
Link: https://patch.msgid.link/342ff94b3dcbb07da1c7dab862a73933d604b717.1730381292.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
On a SMI device, set requested plane_num when querying PPCNT register
with the PortCounters Attribute group.
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
Link: https://patch.msgid.link/828d57444a0a41042556bb0a4394ecf2fcaed639.1730368052.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Support QP with out-of-order (OOO) capabilities enabled.
This allows WRs on the receiver side of the QP to be consumed OOO,
permitting the sender side to transmit messages without guaranteeing
arrival order on the receiver side.
When enabled, the completion ordering of WRs remains in-order,
regardless of the Receive WRs consumption order.
RDMA Read and RDMA Atomic operations on the responder side continue to
be executed in-order, while the ordering of data placement for RDMA
Write and Send operations is not guaranteed.
Atomic operations larger than 8 bytes are currently not supported.
Therefore, when this feature is enabled, the created QP restricts its
atomic support to 8 bytes at most.
In addition, when querying the device, a new flag is returned in
response to indicate that the Kernel supports OOO QP.
Signed-off-by: Edward Srouji <edwards@nvidia.com>
Reviewed-by: Yishai Hadas <yishaih@nvidia.com>
Link: https://patch.msgid.link/06ac609a5f358c8fb0a090d22c61a2f9329d82e6.1725362773.git.leon@kernel.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Adding support for a per device debugfs folder for exporting
some of the device specific debug information.
Added support to get QP info for now. The same folder can be
used to export other debug features in future.
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-5-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Support interfaces to get the raw data for each of
the resources. Use this interface to get some of the
HW structures from active resources.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-4-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Implements support for querying the hardware resource
contexts. This raw data can be used for the debugging
of the field issues.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-3-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Allow users to dump driver specific resource details when
queried through rdma tool. This supports the driver data
for QP, CQ, MR and SRQ.
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1730428483-17841-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Same with commit e375b9c92985 ("RDMA/cxgb4: Set queue pair state when
being queried"). The API for ib_query_qp requires the driver to set
cur_qp_state on return, add the missing set.
Fixes: 8700e3e7c485 ("Soft RoCE driver")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://patch.msgid.link/20241031092019.2138467-1-liujian56@huawei.com
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add drm_panic support for nv50+ cards.
It's enough to get the panic screen while running Gnome/Wayland with
an nv50+ nvidia GPU.
It doesn't support multi-plane or compressed format yet.
Tiling is tested on GTX1650 (Turing), GeForce GT 1030 (Pascal) and
Geforce 8800 GTS (Tesla).
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241022185553.1103384-4-jfalempe@redhat.com
|
|
Refactor, and move the tiling geometry functions to dispnv50/tile.h,
so they can be re-used by drm_panic.
No functional impact.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241022185553.1103384-3-jfalempe@redhat.com
|
|
Add support for ABGR2101010, used by the nouveau driver.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241022185553.1103384-2-jfalempe@redhat.com
|
|
NXP ESDHC supports setting data timeout using uSDHCx_SYS_CTRL register
DTOCV bits (bits 16-19).
Currently the driver accesses those bits by 32-bit write using
SDHCI_TIMEOUT_CONTROL (0x2E) defined in drivers/mmc/host/sdhci.h.
This is offset by two bytes relative to uSDHCx_SYS_CTRL (0x2C).
The driver also defines ESDHC_SYS_CTRL_DTOCV_MASK as first 4 bits, which
is correct relative to SDHCI_TIMEOUT_CONTROL but not relative to
uSDHCx_SYS_CTRL. The definition carrying control register in its name is
therefore inconsistent.
Update the bitmask definition for bits 16-19 to be correct relative to
control register base.
Update the esdhc_set_timeout function to set timeout value at control
register base, not timeout offset.
This solves a purely cosmetic problem.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101-imx-emmc-reset-v3-2-184965eed476@solid-run.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
NXP ESDHC supports control of native emmc reset signal when pinmux is
set accordingly, using uSDHCx_SYS_CTRL register IPP_RST_N bit.
Documentation is available in NXP i.MX6Q Reference Manual.
Implement the hw_reset function in sdhci_ops asserting reset for at
least 1us and waiting at least 200us after deassertion.
Lower bounds are based on:
JEDEC Standard No. 84-B51, 6.15.10 H/W Reset Operation, page 159.
Upper bounds are chosen allowing flexibility to the scheduler.
Tested on SolidRun i.MX8DXL SoM with a scope, and confirmed that eMMC is
still accessible after boot:
- eMMC extcsd has RST_N_FUNCTION=0x01
- sdhc node has cap-mmc-hw-reset
- pinmux set for EMMC0_RESET_B
- Linux v5.15
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Message-ID: <20241101-imx-emmc-reset-v3-1-184965eed476@solid-run.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There is a type issue in assignment in the sd_uhs2_dev_init(),
sd_uhs2_enum() and sd_uhs2_config_write() that will generate
a warning when building the kernel. Let's fix it.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410260423.15jvE6qc-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202410261827.7h8YK8u2-lkp@intel.com/
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Message-ID: <20241101104416.4954-2-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
There is a type issue in the argument in the uhs2_dev_cmd()
that will generate a warning when building the kernel.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202410260525.ZUuPhMJz-lkp@intel.com/
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw>
Message-ID: <20241101104416.4954-1-victorshihgli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
CRTC creation uses drmm_crtc_init_with_planes(), which automatically
handles cleanup. However, an unnecessary call to drm_crtc_cleanup() is
still present in the vkms_output_init() error path.
Fixes: 99cc528ebe92 ("drm/vkms: Use drmm_crtc_init_with_planes()")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Maíra Canal <mcanal@igalia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241031183835.3633-1-jose.exposito89@gmail.com
Acked-by: Louis Chauvet <louis.chauvet@bootlin.com>
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
|
|
*-objs suffix is reserved rather for (user-space) host programs while
usually *-y suffix is used for kernel drivers (although *-objs works
for that purpose for now).
Let's correct the old usages of *-objs in Makefiles.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
The scancodes for the Mic Mute and Airplane keys on the Ideapad Pro 5
(14AHP9 at least, probably the other variants too) are different and
were not being picked up by the driver. This adds them to the keymap.
Apart from what is already supported, the remaining fn keys are
unfortunately producing windows-specific key-combos.
Signed-off-by: Renato Caldas <renato@calgera.com>
Link: https://lore.kernel.org/r/20241102183116.30142-1-renato@calgera.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Some Alienware devices have a key that locks/unlocks the Meta key. This
key triggers a WMI event that should be ignored by the kernel, as it's
handled by internally the firmware.
There is no known way of changing this default behavior. The firmware
would lock/unlock the Meta key, regardless of how the event is handled.
Tested on an Alienware x15 R1.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20241031154441.6663-2-kuurtb@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Fixes the following error:
dell_smbios: Unable to run on non-Dell system
Which is triggered after dell-wmi driver fails to initialize on
Alienware systems, as it depends on dell-smbios.
This effectively extends dell-wmi, dell-smbios and dcdbas support to
Alienware devices, that might share some features of the SMBIOS intereface
calling interface with other Dell products.
Tested on an Alienware X15 R1.
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20241031154023.6149-2-kuurtb@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Loading the amd_pmc module as:
amd_pmc enable_stb=1
...can result in the following messages in the kernel ring buffer:
amd_pmc AMDI0009:00: SMU cmd failed. err: 0xff
ioremap on RAM at 0x0000000000000000 - 0x0000000000ffffff
WARNING: CPU: 10 PID: 2151 at arch/x86/mm/ioremap.c:217 __ioremap_caller+0x2cd/0x340
Further debugging reveals that this occurs when the requests for
S2D_PHYS_ADDR_LOW and S2D_PHYS_ADDR_HIGH return a value of 0,
indicating that the STB is inaccessible. To prevent the ioremap
warning and provide clarity to the user, handle the invalid address
and display an error message.
Link: https://lore.kernel.org/platform-driver-x86/c588ff5d-3e04-4549-9a86-284b9b4419ba@amd.com
Fixes: 3d7d407dfb05 ("platform/x86: amd-pmc: Add support for AMD Spill to DRAM STB feature")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Corey Hickey <bugfood-c@fatooh.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20241028180241.1341624-1-bugfood-ml@fatooh.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The i.MX95 ENETC has been upgraded to revision 4.1, which is different
from the LS1028A ENETC (revision 1.0) except for the SI part. Therefore,
the fsl-enetc driver is incompatible with i.MX95 ENETC PF. So add new
nxp-enetc4 driver to support i.MX95 ENETC PF, and this driver will be
used to support the ENETC PF with major revision 4 for other SoCs in the
future.
Currently, the nxp-enetc4 driver only supports basic transmission feature
for i.MX95 ENETC PF, the more basic and advanced features will be added
in the subsequent patches. In addition, PCS support has not been added
yet, so 10G ENETC (ENETC instance 2) is not supported now.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a situation where num_tx_rings cannot be divided by bdr_int_num.
For example, num_tx_rings is 8 and bdr_int_num is 3. According to the
previous logic, this results in two tx_bdr corresponding memories not
being allocated, so when sending packets to tx ring 6 or 7, wild pointers
will be accessed. Of course, this issue doesn't exist on LS1028A, because
its num_tx_rings is 8, and bdr_int_num is either 1 or 2. However, there
is a risk for the upcoming i.MX95. Therefore, it is necessary to ensure
that each tx_bdr can be allocated to the corresponding memory.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract enetc_int_vector_init() and enetc_int_vector_destroy() from
enetc_alloc_msix() so that the code is more concise and readable.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The verdor ID and device ID of i.MX95 EMDIO are different from LS1028A
EMDIO, so add new vendor ID and device ID to pci_device_id table to
support i.MX95 EMDIO.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ERR050089 workaround causes performance degradation and potential
functional issues (e.g., RCU stalls) under certain workloads. Since
new SoCs like i.MX95 do not require this workaround, use a static key
to compile out enetc_lock_mdio() and enetc_unlock_mdio() at runtime,
improving performance and avoiding unnecessary logic.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compile enetc_pf_common.c as a standalone module to allow shared usage
between ENETC v1 and v4 PF drivers. Add struct enetc_pf_ops to register
different hardware operation interfaces for both ENETC v1 and v4 PF
drivers.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ENETC PF driver of LS1028A (rev 1.0) is incompatible with the version
used on the i.MX95 platform (rev 4.1), except for the station interface
(SI) part. To reduce code redundancy and prepare for a new driver for rev
4.1 and later, extract shared interfaces from enetc_pf.c and move them to
enetc_pf_common.c. This refactoring lays the groundwork for compiling
enetc_pf_common.c into a shared driver for both platforms' PF drivers.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netc-blk-ctrl driver is used to configure Integrated Endpoint
Register Block (IERB) and Privileged Register Block (PRB) of NETC.
For i.MX platforms, it is also used to configure the NETCMIX block.
The IERB contains registers that are used for pre-boot initialization,
debug, and non-customer configuration. The PRB controls global reset
and global error handling for NETC. The NETCMIX block is mainly used
to set MII protocol and PCS protocol of the links, it also contains
settings for some other functions.
Note the IERB configuration registers can only be written after being
unlocked by PRB, otherwise, all write operations are inhibited. A warm
reset is performed when the IERB is unlocked, and it results in an FLR
to all NETC devices. Therefore, all NETC device drivers must be probed
or initialized after the warm reset is finished.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SMU metrics table support for 1Ah family 60h model. This information
will be used by the PMF driver to alter the system thermals.
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20241023063245.1404420-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
When remaining resources are being cleaned up on driver close,
outstanding VM mappings may result in resources being leaked, due
to an object reference loop, as shown below, with each object (or
set of objects) referencing the object below it:
PVR GEM Object
GPU scheduler "finished" fence
GPU scheduler “scheduled” fence
PVR driver “done” fence
PVR Context
PVR VM Context
PVR VM Mappings
PVR GEM Object
The reference that the PVR VM Context has on the VM mappings is a
soft one, in the sense that the freeing of outstanding VM mappings
is done as part of VM context destruction; no reference counts are
involved, as is the case for all the other references in the loop.
To break the reference loop during cleanup, free the outstanding
VM mappings before destroying the PVR Context associated with the
VM context.
Signed-off-by: Brendan King <brendan.king@imgtec.com>
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/8a25924f-1bb7-4d9a-a346-58e871dfb1d1@imgtec.com
|
|
This adds a linked list of VM contexts which is needed for the next patch
to be able to correctly track VM contexts for destruction on file close.
It is only safe for VM contexts to be removed from the list and destroyed
when not in interrupt context.
Signed-off-by: Brendan King <brendan.king@imgtec.com>
Signed-off-by: Matt Coster <matt.coster@imgtec.com>
Reviewed-by: Frank Binns <frank.binns@imgtec.com>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/e57128ea-f0ce-4e93-a9d4-3f033a8b06fa@imgtec.com
|
|
Since commit fde192511bdb ("kconfig: remove tristate choice support"),
all choice blocks are now boolean. There is no longer a need to specify
the choice type explicitly.
Most choice blocks already use "prompt". Before the next commit removes
support for the "bool" syntax in choice entries, this commit converts
the remaining "bool" occurences under drivers/usb/.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Some architectures embed boot DTBs in vmlinux. A potential issue for
these architectures is a race condition during parallel builds because
Kbuild descends into arch/*/boot/dts/ twice.
One build thread is initiated by the 'dtbs' target, which is a
prerequisite of the 'all' target in the top-level Makefile:
ifdef CONFIG_OF_EARLY_FLATTREE
all: dtbs
endif
For architectures that support the built-in boot dtb, arch/*/boot/dts/
is visited also during the ordinary directory traversal in order to
build obj-y objects that wrap DTBs.
Since these build threads are unaware of each other, they can run
simultaneously during parallel builds.
This commit introduces a generic build rule to scripts/Makefile.vmlinux
to support embedded boot DTBs in a race-free way. Architectures that
want to use this rule need to select CONFIG_GENERIC_BUILTIN_DTB.
After the migration, Makefiles under arch/*/boot/dts/ will be visited
only once to build only *.dtb files.
This change also aims to unify the CONFIG options used for built-in DTBs
support. Currently, different architectures use different CONFIG options
for the same purposes.
With this commit, the CONFIG options will be unified as follows:
- CONFIG_GENERIC_BUILTIN_DTB
This enables the generic rule for built-in boot DTBs. This will be
renamed to CONFIG_BUILTIN_DTB after all architectures migrate to the
generic rule.
- CONFIG_BUILTIN_DTB_NAME
This specifies the path to the embedded DTB.
(relative to arch/*/boot/dts/)
- CONFIG_BUILTIN_DTB_ALL
If this is enabled, all DTB files compiled under arch/*/boot/dts/ are
embedded into vmlinux. Only used by MIPS.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Commit e68a558fb2af ("speakup: Fix building as extmod") was intended
to support building this as an external module.
Since commit b1992c3772e6 ("kbuild: use $(src) instead of
$(srctree)/$(src) for source directory"), $(src) consistently points
to the source directory, regardless of whether it is compiled as an
external module or not.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
|
|
Changes in Dynamic Range and Mastering infoframe
should not trigger a full modeset. Therefore, allow
fastset. DP SDP programming is already hooked up in the
fastset flow but HDMI AVI infoframe update is not, add it.
Any other infoframe that can be fastset should be added to
the helper intel_hdmi_fastset_infoframes().
v3:
- Create a wrapper intel_ddi_update_pipe_hdmi to stick to
uniform naming (Jani)
- Do not disable HDMI AVI infoframe if already disabled (Uma)
v2:
- Update HDMI AVI infoframe during fastset.
Signed-off-by: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241023044122.3889137-1-chaitanya.kumar.borah@intel.com
|
