| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux
Pull pwm updates from Uwe Kleine-König:
"Here comes the usual mix of cleanups, new dt-bindings for existing
drivers and nexus nodes; and a new driver for the pwm subsystem.
Patches were contributed by Andy Shevchenko, Chen Wang, Chukun Pan,
Frank Li, Herve Codina, Kever Yang, and Nam Cao. Patch feedback was
provided by Andy Shevchenko, Conor Dooley, Daniel Mack, Duje
Mihanović, Heiko Stuebner, Herve Codina, Krzysztof Kozlowski, Neil
Armstrong, Rob Herring, and Zack Rusin. Thanks to all of them"
* tag 'pwm/for-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
dt-bindings: pwm: imx: Add i.MX93, i.MX94 and i.MX95 support
dt-bindings: pwm: rockchip: Add rockchip,rk3528-pwm
pwm: stmpe: Allow to compile as a module
pwm: Check for CONFIG_PWM using IS_REACHABLE() in main header
dt-bindings: pwm: rockchip: Add rockchip,rk3562-pwm
pwm: Strengthen dependency for PWM_SIFIVE
pwm: clps711x: Drop of_match_ptr() usage for .of_match_table
pwm: pca9685: Drop ACPI_PTR() and of_match_ptr()
pwm: Add support for pwm nexus dt bindings
dt-bindings: pwm: Add support for PWM nexus node
pwm: Add upgrade path to #pwm-cells = <3> for users of of_pwm_single_xlate()
pwm: gpio: Switch to use hrtimer_setup()
pwm: sophgo: add driver for Sophgo SG2042 PWM
dt-bindings: pwm: sophgo: add PWM controller for SG2042
pwm: lpss: Only include <linux/pwm.h> where needed
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The biggest change for SPI this release is the addition of offload
support from David Lechner, allowing the hardware to trigger SPI
transactions autonomously. The initial use case is for triggering IIO
operations but there are other applications where having the hardware
ready to go at a minimal signal is useful for synchronising with
external inputs (eg, interrupt handling) or reducing latency (eg, CAN
networking).
Otherwise there's the usual fixes, improvements and cleanups, plus
support for a bunch of new devices.
- Support for offloading support from David Lechner
- Support for GOcontrol1 Moduline modules, Mediatek MT7988, NXP
i.MX94, Qualcomm SPI NAMD, Rockchip RK3562, Sophogo SG2044 and ST
STM32 OSPI"
* tag 'spi-v6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (59 commits)
spi: spi-mem: Introduce a default ->exec_op() debug log
spi: dt-bindings: cdns,qspi-nor: Require some peripheral properties
spi: dt-bindings: cdns,qspi-nor: Deprecate the Cadence compatible alone
spi: dt-bindings: cdns,qspi-nor: Be more descriptive regarding what this controller is
spi: stm32-ospi: Include "gpio/consumer.h"
MAINTAINERS: adjust the file entry in GOCONTROLL MODULINE MODULE SLOT
spi: spi-qpic-snand: avoid memleak in qcom_spi_ecc_init_ctx_pipelined()
spi: spi-mux: Fix coverity issue, unchecked return value
spi: sophgo: fix incorrect type for ret in sg2044_spifmc_write()
spi: sg2044-nor: fix uninitialized variable in probe
spi: sg2044-nor: fix signedness bug in sg2044_spifmc_write()
spi: sg2044-nor: Convert to dev_err_probe()
spi: sg2044-nor: Fully convert to device managed resources
dt-bindings: spi: add compatibles for mt7988
spi: spidev: Add an entry for the gocontroll moduline module slot
MAINTAINERS: add maintainer for the GOcontroll Moduline module slot
dt-bindings: connector: Add the GOcontroll Moduline module slot bindings
dt-bindings: vendor-prefixes: add GOcontroll
spi: Use inclusive language
spi: cadence-qspi: Improve spi memory performance
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very quiet release, we've got support for one device
added, another removed, and some smaller fixes and API improvements.
The main thing of note is the rework of the PCA9450 LDO5 handling.
- A rework of the handling of LDO5 on the PCA9450, this was quite
wrong in how it handled the SD_VSEL conrol and only worked for some
system designs. This includes a DTS update since there was a not
quite ABI compatible change as part of the fix
- A devres change introducing devm_kmemdup_array() was pulled in so
it could be used with some regulator conversions to that function,
this pulled in some other devres and IIO stuff that was part of the
same pull request
- Removal of the PCF50633 driver, the SoC for the OpenMoko platform
that used it has been removed
- Support for the NXP PF9453"
* tag 'regulator-v6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (24 commits)
regulator: axp20x: AXP717: dcdc4 doesn't have delay
regulator: dt-bindings: rtq2208: Cleanup whitespace
regulator: dt-bindings: rtq2208: Mark fixed LDO VOUT property as deprecated
regulator: rtq6752: make const read-only array fault_mask static
regulator: pf9453: add PMIC PF9453 support
regulator: dt-bindings: pca9450: Add nxp,pf9453 compatible string
regulator: pcf50633-regulator: Remove
regulator: pca9450: Handle hardware with fixed SD_VSEL for LDO5
regulator: cros-ec: use devm_kmemdup_array()
regulator: devres: use devm_kmemdup_array()
regulator: Add (devm_)of_regulator_get()
devres: Introduce devm_kmemdup_array()
iio: imu: st_lsm9ds0: Replace device.h with what is needed
driver core: Split devres APIs to device/devres.h
err.h: move IOMEM_ERR_PTR() to err.h
regulator: pca9450: Remove duplicate code in probe
regulator: ad5398: Fix incorrect power down bit mask
regulator: pca9450: Fix enable register for LDO5
regulator: pca9450: Fix control register for LDO5
Revert "regulator: pca9450: Add SD_VSEL GPIO for LDO5"
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux
Pull CRC updates from Eric Biggers:
"Another set of improvements to the kernel's CRC (cyclic redundancy
check) code:
- Rework the CRC64 library functions to be directly optimized, like
what I did last cycle for the CRC32 and CRC-T10DIF library
functions
- Rewrite the x86 PCLMULQDQ-optimized CRC code, and add VPCLMULQDQ
support and acceleration for crc64_be and crc64_nvme
- Rewrite the riscv Zbc-optimized CRC code, and add acceleration for
crc_t10dif, crc64_be, and crc64_nvme
- Remove crc_t10dif and crc64_rocksoft from the crypto API, since
they are no longer needed there
- Rename crc64_rocksoft to crc64_nvme, as the old name was incorrect
- Add kunit test cases for crc64_nvme and crc7
- Eliminate redundant functions for calculating the Castagnoli CRC32,
settling on just crc32c()
- Remove unnecessary prompts from some of the CRC kconfig options
- Further optimize the x86 crc32c code"
* tag 'crc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux: (36 commits)
x86/crc: drop the avx10_256 functions and rename avx10_512 to avx512
lib/crc: remove unnecessary prompt for CONFIG_CRC64
lib/crc: remove unnecessary prompt for CONFIG_LIBCRC32C
lib/crc: remove unnecessary prompt for CONFIG_CRC8
lib/crc: remove unnecessary prompt for CONFIG_CRC7
lib/crc: remove unnecessary prompt for CONFIG_CRC4
lib/crc7: unexport crc7_be_syndrome_table
lib/crc_kunit.c: update comment in crc_benchmark()
lib/crc_kunit.c: add test and benchmark for crc7_be()
x86/crc32: optimize tail handling for crc32c short inputs
riscv/crc64: add Zbc optimized CRC64 functions
riscv/crc-t10dif: add Zbc optimized CRC-T10DIF function
riscv/crc32: reimplement the CRC32 functions using new template
riscv/crc: add "template" for Zbc optimized CRC functions
x86/crc: add ANNOTATE_NOENDBR to suppress objtool warnings
x86/crc32: improve crc32c_arch() code generation with clang
x86/crc64: implement crc64_be and crc64_nvme using new template
x86/crc-t10dif: implement crc_t10dif using new template
x86/crc32: implement crc32_le using new template
x86/crc: add "template" for [V]PCLMULQDQ based CRC functions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm
Pull lsm updates from Paul Moore:
- Various minor updates to the LSM Rust bindings
Changes include marking trivial Rust bindings as inlines and comment
tweaks to better reflect the LSM hooks.
- Add LSM/SELinux access controls to io_uring_allowed()
Similar to the io_uring_disabled sysctl, add a LSM hook to
io_uring_allowed() to enable LSMs a simple way to enforce security
policy on the use of io_uring. This pull request includes SELinux
support for this new control using the io_uring/allowed permission.
- Remove an unused parameter from the security_perf_event_open() hook
The perf_event_attr struct parameter was not used by any currently
supported LSMs, remove it from the hook.
- Add an explicit MAINTAINERS entry for the credentials code
We've seen problems in the past where patches to the credentials code
sent by non-maintainers would often languish on the lists for
multiple months as there was no one explicitly tasked with the
responsibility of reviewing and/or merging credentials related code.
Considering that most of the code under security/ has a vested
interest in ensuring that the credentials code is well maintained,
I'm volunteering to look after the credentials code and Serge Hallyn
has also volunteered to step up as an official reviewer. I posted the
MAINTAINERS update as a RFC to LKML in hopes that someone else would
jump up with an "I'll do it!", but beyond Serge it was all crickets.
- Update Stephen Smalley's old email address to prevent confusion
This includes a corresponding update to the mailmap file.
* tag 'lsm-pr-20250323' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
mailmap: map Stephen Smalley's old email addresses
lsm: remove old email address for Stephen Smalley
MAINTAINERS: add Serge Hallyn as a credentials reviewer
MAINTAINERS: add an explicit credentials entry
cred,rust: mark Credential methods inline
lsm,rust: reword "destroy" -> "release" in SecurityCtx
lsm,rust: mark SecurityCtx methods inline
perf: Remove unnecessary parameter of security check
lsm: fix a missing security_uring_allowed() prototype
io_uring,lsm,selinux: add LSM hooks for io_uring_setup()
io_uring: refactor io_uring_allowed()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control updates from Rafael Wysocki:
"These include one thermal core fix for an issue leading to a NULL
pointer dereference, a similar fix for the int340x thermal driver
(even though the issue may not actually occur in practice in this
particular case), and a bunch of cleanups, mostly related to replacing
kzalloc() with kcalloc() where applicable.
Summary:
- Delay exposing thermal zone sysfs interface to prevent user space
from accessing thermal zones that have not been completely
initialized yet (Lucas De Marchi)
- Check a pointer against NULL early in int3402_thermal_probe() to
avoid a potential NULL pointer dereference (Chenyuan Yang)
- Use kcalloc() instead of kzalloc() in some places in the thermal
control subsystem (Lukasz Luba, Ethan Carter Edwards)
- Fix a spelling mistake in a comment in the thermal core (Colin Ian
King)
- Clean up variable initialization in int340x_thermal_zone_add()
(Christophe JAILLET)"
* tag 'thermal-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: Add NULL check for adev
thermal: core: Delay exposing sysfs interface
thermal: core: Fix spelling mistake "Occurences" -> "Occurrences"
thermal: intel: Clean up zone_trips[] initialization in int340x_thermal_zone_add()
thermal: hisi: Use kcalloc() instead of kzalloc() with multiplication
thermal: int340x: Use kcalloc() instead of kzalloc() with multiplication
thermal: k3_j72xx_bandgap: Use kcalloc() instead of kzalloc()
thermal/of: Use kcalloc() instead of kzalloc() with multiplication
thermal/debugfs: replace kzalloc() with kcalloc() in thermal_debug_tz_add()
|
|
rk806_set_mode_dcdc()
If 'ctr_bit' is negative, the shift counts become negative, causing a
shift of bounds and undefined behavior.
Presumably that's not possible in normal operation, but the code
generation isn't optimal. And undefined behavior should be avoided
regardless.
Improve code generation and remove the undefined behavior by converting
the signed variables to unsigned.
Fixes the following warning with an UBSAN kernel:
vmlinux.o: warning: objtool: rk806_set_mode_dcdc() falls through to next function rk806_get_mode_dcdc()
vmlinux.o: warning: objtool: .text.rk806_set_mode_dcdc: unexpected end of section
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/2023abcddf3f524ba478d64339996f25dc4097d2.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202503182350.52KeHGD4-lkp@intel.com/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These are dominated by cpufreq updates which in turn are dominated by
updates related to boost support in the core and drivers and
amd-pstate driver optimizations.
Apart from the above, there are some cpuidle updates including a
rework of the most recent idle intervals handling in the venerable
menu governor that leads to significant improvements in some
performance benchmarks, as the governor is now more likely to predict
a shorter idle duration in some cases, and there are updates of the
core device power management code, mostly related to system suspend
and resume, that should help to avoid potential issues arising when
the drivers of devices depending on one another want to use different
optimizations.
There is also a usual collection of assorted fixes and cleanups,
including removal of some unused code.
Specifics:
- Manage sysfs attributes and boost frequencies efficiently from
cpufreq core to reduce boilerplate code in drivers (Viresh Kumar)
- Minor cleanups to cpufreq drivers (Aaron Kling, Benjamin Schneider,
Dhananjay Ugwekar, Imran Shaik, zuoqian)
- Migrate some cpufreq drivers to using for_each_present_cpu() (Jacky
Bai)
- cpufreq-qcom-hw DT binding fixes (Krzysztof Kozlowski)
- Use str_enable_disable() helper in cpufreq_online() (Lifeng Zheng)
- Optimize the amd-pstate driver to avoid cases where call paths end
up calling the same writes multiple times and needlessly caching
variables through code reorganization, locking overhaul and tracing
adjustments (Mario Limonciello, Dhananjay Ugwekar)
- Make it possible to avoid enabling capacity-aware scheduling (CAS)
in the intel_pstate driver and relocate a check for out-of-band
(OOB) platform handling in it to make it detect OOB before checking
HWP availability (Rafael Wysocki)
- Fix dbs_update() to avoid inadvertent conversions of negative
integer values to unsigned int which causes CPU frequency selection
to be inaccurate in some cases when the "conservative" cpufreq
governor is in use (Jie Zhan)
- Update the handling of the most recent idle intervals in the menu
cpuidle governor to prevent useful information from being discarded
by it in some cases and improve the prediction accuracy (Rafael
Wysocki)
- Make it possible to tell the intel_idle driver to ignore its
built-in table of idle states for the given processor, clean up the
handling of auto-demotion disabling on Baytrail and Cherrytrail
chips in it, and update its MAINTAINERS entry (David Arcari, Artem
Bityutskiy, Rafael Wysocki)
- Make some cpuidle drivers use for_each_present_cpu() instead of
for_each_possible_cpu() during initialization to avoid issues
occurring when nosmp or maxcpus=0 are used (Jacky Bai)
- Clean up the Energy Model handling code somewhat (Rafael Wysocki)
- Use kfree_rcu() to simplify the handling of runtime Energy Model
updates (Li RongQing)
- Add an entry for the Energy Model framework to MAINTAINERS as
properly maintained (Lukasz Luba)
- Address RCU-related sparse warnings in the Energy Model code
(Rafael Wysocki)
- Remove ENERGY_MODEL dependency on SMP and allow it to be selected
when DEVFREQ is set without CPUFREQ so it can be used on a wider
range of systems (Jeson Gao)
- Unify error handling during runtime suspend and runtime resume in
the core to help drivers to implement more consistent runtime PM
error handling (Rafael Wysocki)
- Drop a redundant check from pm_runtime_force_resume() and rearrange
documentation related to __pm_runtime_disable() (Rafael Wysocki)
- Rework the handling of the "smart suspend" driver flag in the PM
core to avoid issues hat may occur when drivers using it depend on
some other drivers and clean up the related PM core code (Rafael
Wysocki, Colin Ian King)
- Fix the handling of devices with the power.direct_complete flag set
if device_suspend() returns an error for at least one device to
avoid situations in which some of them may not be resumed (Rafael
Wysocki)
- Use mutex_trylock() in hibernate_compressor_param_set() to avoid a
possible deadlock that may occur if the "compressor" hibernation
module parameter is accessed during the registration of a new
ieee80211 device (Lizhi Xu)
- Suppress sleeping parent warning in device_pm_add() in the case
when new children are added under a device with the
power.direct_complete set after it has been processed by
device_resume() (Xu Yang)
- Remove needless return in three void functions related to system
wakeup (Zijun Hu)
- Replace deprecated kmap_atomic() with kmap_local_page() in the
hibernation core code (David Reaver)
- Remove unused helper functions related to system sleep (David Alan
Gilbert)
- Clean up s2idle_enter() so it does not lock and unlock CPU offline
in vain and update comments in it (Ulf Hansson)
- Clean up broken white space in dpm_wait_for_children() (Geert
Uytterhoeven)
- Update the cpupower utility to fix lib version-ing in it and memory
leaks in error legs, remove hard-coded values, and implement CPU
physical core querying (Thomas Renninger, John B. Wyatt IV, Shuah
Khan, Yiwei Lin, Zhongqiu Han)"
* tag 'pm-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (139 commits)
PM: sleep: Fix bit masking operation
dt-bindings: cpufreq: cpufreq-qcom-hw: Narrow properties on SDX75, SA8775p and SM8650
dt-bindings: cpufreq: cpufreq-qcom-hw: Drop redundant minItems:1
dt-bindings: cpufreq: cpufreq-qcom-hw: Add missing constraint for interrupt-names
dt-bindings: cpufreq: cpufreq-qcom-hw: Add QCS8300 compatible
cpufreq: Init cpufreq only for present CPUs
PM: sleep: Fix handling devices with direct_complete set on errors
cpuidle: Init cpuidle only for present CPUs
PM: clk: Remove unused pm_clk_remove()
PM: sleep: core: Fix indentation in dpm_wait_for_children()
PM: s2idle: Extend comment in s2idle_enter()
PM: s2idle: Drop redundant locks when entering s2idle
PM: sleep: Remove unused pm_generic_ wrappers
cpufreq: tegra186: Share policy per cluster
cpupower: Make lib versioning scheme more obvious and fix version link
PM: EM: Rework the depends on for CONFIG_ENERGY_MODEL
PM: EM: Address RCU-related sparse warnings
cpupower: Implement CPU physical core querying
pm: cpupower: remove hard-coded topology depth values
pm: cpupower: Fix cmd_monitor() error legs to free cpu_topology
...
|
|
In cyapa_update_fw_store(), if 'count' is zero, the write to
fw_name[count-1] underflows the array.
Presumably that's not possible in normal operation, as its caller
sysfs_kf_write() already checks for zero. Regardless it's a good idea
to check for the error explicitly and avoid undefined behavior.
Fixes the following warning with an UBSAN kernel:
vmlinux.o: warning: objtool: .text.cyapa_update_fw_store: unexpected end of section
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/73ae0bb3c656735890d914b74c9d6bb40c25d3cd.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202503171547.LlCTJLQL-lkp@intel.com/
|
|
If dib8000_set_dds()'s call to dib8000_read32() returns zero, the result
is a divide-by-zero. Prevent that from happening.
Fixes the following warning with an UBSAN kernel:
drivers/media/dvb-frontends/dib8000.o: warning: objtool: dib8000_tune() falls through to next function dib8096p_cfg_DibRx()
Fixes: 173a64cb3fcf ("[media] dib8000: enhancement")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/bd1d504d930ae3f073b1e071bcf62cae7708773c.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/r/202503210602.fvH5DO1i-lkp@intel.com/
|
|
The csts_state_names[] array only has six sparse entries, but the
iteration code in nvmet_ctrl_state_show() iterates seven, resulting in a
potential out-of-bounds stack read. Fix that.
Fixes the following warning with an UBSAN kernel:
vmlinux.o: warning: objtool: .text.nvmet_ctrl_state_show: unexpected end of section
Fixes: 649fd41420a8 ("nvmet: add debugfs support")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/f1f60858ee7a941863dc7f5506c540cb9f97b5f6.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/oe-kbuild-all/202503171547.LlCTJLQL-lkp@intel.com/
|
|
If speed_hz < AMD_SPI_MIN_HZ, amd_set_spi_freq() iterates over the
entire amd_spi_freq array without breaking out early, causing 'i' to go
beyond the array bounds.
Fix that by stopping the loop when it gets to the last entry, so the low
speed_hz value gets clamped up to AMD_SPI_MIN_HZ.
Fixes the following warning with an UBSAN kernel:
drivers/spi/spi-amd.o: error: objtool: amd_set_spi_freq() falls through to next function amd_spi_set_opcode()
Fixes: 3fe26121dc3a ("spi: amd: Configure device speed")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Cc: Raju Rangoju <Raju.Rangoju@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/78fef0f2434f35be9095bcc9ffa23dd8cab667b9.1742852847.git.jpoimboe@kernel.org
Closes: https://lore.kernel.org/r/202503161828.RUk9EhWx-lkp@intel.com/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"From the functional perspective, the most significant changes here are
the ACPI fan driver update allowing it to handle fans with
fine-grained state checking supported, but without fine-grained
control, and the ACPI button driver update making it subscribe to
system event notifications (in addition to device notifications) which
on some systems is requisite for waking up the system from sleep.
The rest is fixes and cleanups including removal of some dead code.
Specifics:
- Use the str_on_off() helper function instead of hard-coded strings
in the ACPI power resources handling code (Thorsten Blum)
- Add fan speed reporting for ACPI fans that have _FST, but otherwise
do not support the entire ACPI 4 fan interface (Joshua Grisham)
- Fix a stale comment regarding trip points in acpi_thermal_add()
that diverged from the commented code after removing _CRT
evaluation from acpi_thermal_get_trip_points() (xueqin Luo)
- Make ACPI button driver also subscribe to system events (Mario
Limonciello)
- Use the str_yes_no() helper function instead of hard-coded strings
in the ACPI backlight (video) driver (Thorsten Blum)
- Add a missing header file include to the x86 arch CPPC code (Mario
Limonciello)
- Rework the sysfs attributes implementation in the ACPI
platform-profile driver and improve the unregistration code in it
(Nathan Chancellor, Kurt Borja)
- Prevent the ACPI HED driver from being built as a module and change
its initcall level to subsys_initcall to avoid initialization
ordering issues related to it (Xiaofei Tan)
- Update a maintainer email address in the ACPI PMIC entry in
MAINTAINERS (Mika Westerberg)
- Address a GCC 15's -Wunterminated-string-initialization warning in
the core PNP subsystem code and remove some dead code from it (Kees
Cook, David Alan Gilbert)"
* tag 'acpi-6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PNP: Expand length of fixup id string
PNP: Remove prehistoric deadcode
ACPI: button: Install notifier for system events as well
ACPI: fan: Add fan speed reporting for fans with only _FST
ACPI: HED: Always initialize before evged
x86/ACPI: CPPC: Add missing include
ACPI: video: Use str_yes_no() helper in acpi_video_bus_add()
ACPI: platform_profile: Improve platform_profile_unregister()
ACPI: platform-profile: Fix CFI violation when accessing sysfs files
ACPI: power: Use str_on_off() helper function
ACPI: thermal: Fix stale comment regarding trip points
MAINTAINERS: Use my kernel.org address for ACPI PMIC work
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv updates from Wei Liu:
- Add support for running as the root partition in Hyper-V (Microsoft
Hypervisor) by exposing /dev/mshv (Nuno and various people)
- Add support for CPU offlining in Hyper-V (Hamza Mahfooz)
- Misc fixes and cleanups (Roman Kisel, Tianyu Lan, Wei Liu, Michael
Kelley, Thorsten Blum)
* tag 'hyperv-next-signed-20250324' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (24 commits)
x86/hyperv: fix an indentation issue in mshyperv.h
x86/hyperv: Add comments about hv_vpset and var size hypercall input args
Drivers: hv: Introduce mshv_root module to expose /dev/mshv to VMMs
hyperv: Add definitions for root partition driver to hv headers
x86: hyperv: Add mshv_handler() irq handler and setup function
Drivers: hv: Introduce per-cpu event ring tail
Drivers: hv: Export some functions for use by root partition module
acpi: numa: Export node_to_pxm()
hyperv: Introduce hv_recommend_using_aeoi()
arm64/hyperv: Add some missing functions to arm64
x86/mshyperv: Add support for extended Hyper-V features
hyperv: Log hypercall status codes as strings
x86/hyperv: Fix check of return value from snp_set_vmsa()
x86/hyperv: Add VTL mode callback for restarting the system
x86/hyperv: Add VTL mode emergency restart callback
hyperv: Remove unused union and structs
hyperv: Add CONFIG_MSHV_ROOT to gate root partition support
hyperv: Change hv_root_partition into a function
hyperv: Convert hypercall statuses to linux error codes
drivers/hv: add CPU offlining support
...
|
|
GCC compiler (Debian 14.2.0-17) is not happy about printing
into a too short buffer (when build with `make W=1`):
drivers/net/usb/ax88172a.c:311:9: note: ‘snprintf’ output between 4 and 66 bytes into a destination of size 20
Indeed, the buffer size is chosen based on some assumptions,
while in general the assigned name might not fit. Increase
the buffer size to cover the minimum required one. With that,
change snprintf() to use sizeof() instead of the hard coded
value.
While at it, make sure that the PHY address is not bigger than
the allowed maximum.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patch.msgid.link/20250324144751.1271761-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- cleanup: remove an used function
- add support for a XenServer specific virtual PCI device
- fix the handling of a sparse Xen hypervisor symbol table
- avoid warnings when building the kernel with gcc 15
- fix use of devices behind a VMD bridge when running as a Xen PV dom0
* tag 'for-linus-6.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
PCI/MSI: Convert pci_msi_ignore_mask to per MSI domain flag
PCI: vmd: Disable MSI remapping bypass under Xen
xen/pci: Do not register devices with segments >= 0x10000
xen/pciback: Remove unused pcistub_get_pci_dev
xenfs/xensyms: respect hypervisor's "next" indication
xen/mcelog: Add __nonstring annotations for unterminated strings
xen: Add support for XenServer 6.1 platform device
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- Nested virtualization support for VGICv3, giving the nested
hypervisor control of the VGIC hardware when running an L2 VM
- Removal of 'late' nested virtualization feature register masking,
making the supported feature set directly visible to userspace
- Support for emulating FEAT_PMUv3 on Apple silicon, taking advantage
of an IMPLEMENTATION DEFINED trap that covers all PMUv3 registers
- Paravirtual interface for discovering the set of CPU
implementations where a VM may run, addressing a longstanding issue
of guest CPU errata awareness in big-little systems and
cross-implementation VM migration
- Userspace control of the registers responsible for identifying a
particular CPU implementation (MIDR_EL1, REVIDR_EL1, AIDR_EL1),
allowing VMs to be migrated cross-implementation
- pKVM updates, including support for tracking stage-2 page table
allocations in the protected hypervisor in the 'SecPageTable' stat
- Fixes to vPMU, ensuring that userspace updates to the vPMU after
KVM_RUN are reflected into the backing perf events
LoongArch:
- Remove unnecessary header include path
- Assume constant PGD during VM context switch
- Add perf events support for guest VM
RISC-V:
- Disable the kernel perf counter during configure
- KVM selftests improvements for PMU
- Fix warning at the time of KVM module removal
x86:
- Add support for aging of SPTEs without holding mmu_lock.
Not taking mmu_lock allows multiple aging actions to run in
parallel, and more importantly avoids stalling vCPUs. This includes
an implementation of per-rmap-entry locking; aging the gfn is done
with only a per-rmap single-bin spinlock taken, whereas locking an
rmap for write requires taking both the per-rmap spinlock and the
mmu_lock.
Note that this decreases slightly the accuracy of accessed-page
information, because changes to the SPTE outside aging might not
use atomic operations even if they could race against a clear of
the Accessed bit.
This is deliberate because KVM and mm/ tolerate false
positives/negatives for accessed information, and testing has shown
that reducing the latency of aging is far more beneficial to
overall system performance than providing "perfect" young/old
information.
- Defer runtime CPUID updates until KVM emulates a CPUID instruction,
to coalesce updates when multiple pieces of vCPU state are
changing, e.g. as part of a nested transition
- Fix a variety of nested emulation bugs, and add VMX support for
synthesizing nested VM-Exit on interception (instead of injecting
#UD into L2)
- Drop "support" for async page faults for protected guests that do
not set SEND_ALWAYS (i.e. that only want async page faults at CPL3)
- Bring a bit of sanity to x86's VM teardown code, which has
accumulated a lot of cruft over the years. Particularly, destroy
vCPUs before the MMU, despite the latter being a VM-wide operation
- Add common secure TSC infrastructure for use within SNP and in the
future TDX
- Block KVM_CAP_SYNC_REGS if guest state is protected. It does not
make sense to use the capability if the relevant registers are not
available for reading or writing
- Don't take kvm->lock when iterating over vCPUs in the suspend
notifier to fix a largely theoretical deadlock
- Use the vCPU's actual Xen PV clock information when starting the
Xen timer, as the cached state in arch.hv_clock can be stale/bogus
- Fix a bug where KVM could bleed PVCLOCK_GUEST_STOPPED across
different PV clocks; restrict PVCLOCK_GUEST_STOPPED to kvmclock, as
KVM's suspend notifier only accounts for kvmclock, and there's no
evidence that the flag is actually supported by Xen guests
- Clean up the per-vCPU "cache" of its reference pvclock, and instead
only track the vCPU's TSC scaling (multipler+shift) metadata (which
is moderately expensive to compute, and rarely changes for modern
setups)
- Don't write to the Xen hypercall page on MSR writes that are
initiated by the host (userspace or KVM) to fix a class of bugs
where KVM can write to guest memory at unexpected times, e.g.
during vCPU creation if userspace has set the Xen hypercall MSR
index to collide with an MSR that KVM emulates
- Restrict the Xen hypercall MSR index to the unofficial synthetic
range to reduce the set of possible collisions with MSRs that are
emulated by KVM (collisions can still happen as KVM emulates
Hyper-V MSRs, which also reside in the synthetic range)
- Clean up and optimize KVM's handling of Xen MSR writes and
xen_hvm_config
- Update Xen TSC leaves during CPUID emulation instead of modifying
the CPUID entries when updating PV clocks; there is no guarantee PV
clocks will be updated between TSC frequency changes and CPUID
emulation, and guest reads of the TSC leaves should be rare, i.e.
are not a hot path
x86 (Intel):
- Fix a bug where KVM unnecessarily reads XFD_ERR from hardware and
thus modifies the vCPU's XFD_ERR on a #NM due to CR0.TS=1
- Pass XFD_ERR as the payload when injecting #NM, as a preparatory
step for upcoming FRED virtualization support
- Decouple the EPT entry RWX protection bit macros from the EPT
Violation bits, both as a general cleanup and in anticipation of
adding support for emulating Mode-Based Execution Control (MBEC)
- Reject KVM_RUN if userspace manages to gain control and stuff
invalid guest state while KVM is in the middle of emulating nested
VM-Enter
- Add a macro to handle KVM's sanity checks on entry/exit VMCS
control pairs in anticipation of adding sanity checks for secondary
exit controls (the primary field is out of bits)
x86 (AMD):
- Ensure the PSP driver is initialized when both the PSP and KVM
modules are built-in (the initcall framework doesn't handle
dependencies)
- Use long-term pins when registering encrypted memory regions, so
that the pages are migrated out of MIGRATE_CMA/ZONE_MOVABLE and
don't lead to excessive fragmentation
- Add macros and helpers for setting GHCB return/error codes
- Add support for Idle HLT interception, which elides interception if
the vCPU has a pending, unmasked virtual IRQ when HLT is executed
- Fix a bug in INVPCID emulation where KVM fails to check for a
non-canonical address
- Don't attempt VMRUN for SEV-ES+ guests if the vCPU's VMSA is
invalid, e.g. because the vCPU was "destroyed" via SNP's AP
Creation hypercall
- Reject SNP AP Creation if the requested SEV features for the vCPU
don't match the VM's configured set of features
Selftests:
- Fix again the Intel PMU counters test; add a data load and do
CLFLUSH{OPT} on the data instead of executing code. The theory is
that modern Intel CPUs have learned new code prefetching tricks
that bypass the PMU counters
- Fix a flaw in the Intel PMU counters test where it asserts that an
event is counting correctly without actually knowing what the event
counts on the underlying hardware
- Fix a variety of flaws, bugs, and false failures/passes
dirty_log_test, and improve its coverage by collecting all dirty
entries on each iteration
- Fix a few minor bugs related to handling of stats FDs
- Add infrastructure to make vCPU and VM stats FDs available to tests
by default (open the FDs during VM/vCPU creation)
- Relax an assertion on the number of HLT exits in the xAPIC IPI test
when running on a CPU that supports AMD's Idle HLT (which elides
interception of HLT if a virtual IRQ is pending and unmasked)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (216 commits)
RISC-V: KVM: Optimize comments in kvm_riscv_vcpu_isa_disable_allowed
RISC-V: KVM: Teardown riscv specific bits after kvm_exit
LoongArch: KVM: Register perf callbacks for guest
LoongArch: KVM: Implement arch-specific functions for guest perf
LoongArch: KVM: Add stub for kvm_arch_vcpu_preempted_in_kernel()
LoongArch: KVM: Remove PGD saving during VM context switch
LoongArch: KVM: Remove unnecessary header include path
KVM: arm64: Tear down vGIC on failed vCPU creation
KVM: arm64: PMU: Reload when resetting
KVM: arm64: PMU: Reload when user modifies registers
KVM: arm64: PMU: Fix SET_ONE_REG for vPMC regs
KVM: arm64: PMU: Assume PMU presence in pmu-emul.c
KVM: arm64: PMU: Set raw values from user to PM{C,I}NTEN{SET,CLR}, PMOVS{SET,CLR}
KVM: arm64: Create each pKVM hyp vcpu after its corresponding host vcpu
KVM: arm64: Factor out pKVM hyp vcpu creation to separate function
KVM: arm64: Initialize HCRX_EL2 traps in pKVM
KVM: arm64: Factor out setting HCRX_EL2 traps into separate function
KVM: x86: block KVM_CAP_SYNC_REGS if guest state is protected
KVM: x86: Add infrastructure for secure TSC
KVM: x86: Push down setting vcpu.arch.user_set_tsc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Luiz Augusto von Dentz says:
====================
bluetooth-next pull request for net-next:
core:
- Add support for skb TX SND/COMPLETION timestamping
- hci_core: Enable buffer flow control for SCO/eSCO
- coredump: Log devcd dumps into the monitor
drivers:
- btusb: Add 2 HWIDs for MT7922
- btusb: Fix regression in the initialization of fake Bluetooth controllers
- btusb: Add 14 USB device IDs for Qualcomm WCN785x
- btintel: Add support for Intel Scorpius Peak
- btintel: Add support to configure TX power
- btintel: Add DSBR support for ScP
- btintel_pcie: Add device id of Whale Peak
- btintel_pcie: Setup buffers for firmware traces
- btintel_pcie: Read hardware exception data
- btintel_pcie: Add support for device coredump
- btintel_pcie: Trigger device coredump on hardware exception
- btnxpuart: Support for controller wakeup gpio config
- btnxpuart: Add support to set BD address
- btnxpuart: Add correct bootloader error codes
- btnxpuart: Handle bootloader error during cmd5 and cmd7
- btnxpuart: Fix kernel panic during FW release
- qca: add WCN3950 support
- hci_qca: use the power sequencer for wcn6750
- btmtksdio: Prevent enabling interrupts after IRQ handler removal
* tag 'for-net-next-2025-03-25' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (53 commits)
Bluetooth: MGMT: Add LL Privacy Setting
Bluetooth: hci_event: Fix handling of HCI_EV_LE_DIRECT_ADV_REPORT
Bluetooth: btnxpuart: Fix kernel panic during FW release
Bluetooth: btnxpuart: Handle bootloader error during cmd5 and cmd7
Bluetooth: btnxpuart: Add correct bootloader error codes
t blameBluetooth: btintel: Fix leading white space
Bluetooth: btintel: Add support to configure TX power
Bluetooth: btmtksdio: Prevent enabling interrupts after IRQ handler removal
Bluetooth: btmtk: Remove the resetting step before downloading the fw
Bluetooth: SCO: add TX timestamping
Bluetooth: L2CAP: add TX timestamping
Bluetooth: ISO: add TX timestamping
Bluetooth: add support for skb TX SND/COMPLETION timestamping
net-timestamp: COMPLETION timestamp on packet tx completion
HCI: coredump: Log devcd dumps into the monitor
Bluetooth: HCI: Add definition of hci_rp_remote_name_req_cancel
Bluetooth: hci_vhci: Mark Sync Flow Control as supported
Bluetooth: hci_core: Enable buffer flow control for SCO/eSCO
Bluetooth: btintel_pci: Fix build warning
Bluetooth: btintel_pcie: Trigger device coredump on hardware exception
...
====================
Link: https://patch.msgid.link/20250325192925.2497890-1-luiz.dentz@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The hardware only supports L4 checksum offload for TCP/UDP/SCTP protocol.
There was a bug to set Tx checksum flag for the other protocol that results
in Tx ring hang. Fix to compute software checksum for these packets.
Fixes: 3403960cdf86 ("net: wangxun: libwx add tx offload functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250324103235.823096-2-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The length of skb header was incorrectly calculated when transmit a tunnel
packet with outer IPv6 extension header, or a IP over IP packet which has
inner IPv6 header. Thus the correct Tx context descriptor cannot be
composed, resulting in Tx ring hang.
Fixes: 3403960cdf86 ("net: wangxun: libwx add tx offload functions")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://patch.msgid.link/20250324103235.823096-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- Add infrastructure support to EDAC in order to be able to register
memory scrubbing RAS functionality with the kernel and expose sysfs
nodes to control such scrubbing functionality.
The main use case is CXL devices which provide different scrubbers
for their built-in memories so that tools like rasdaemon can
configure and control memory scrubbing and other, more advanced RAS
functionality (Shiju Jose and Jonathan Cameron)
- Add support to ie31200_edac for client SoCs like Raptor Lake-S which
have multiple memory controllers and out-of-band ECC capability
(Qiuxu Zhuo)
- The usual round of cleanups, simplifications and fixlets
* tag 'edac_updates_for_v6.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras: (25 commits)
MAINTAINERS: Add a secondary maintainer for bluefield_edac
EDAC/ie31200: Switch Raptor Lake-S to interrupt mode
EDAC/ie31200: Add Intel Raptor Lake-S SoCs support
EDAC/ie31200: Break up ie31200_probe1()
EDAC/ie31200: Fold the two channel loops into one loop
EDAC/ie31200: Make struct dimm_data contain decoded information
EDAC/ie31200: Make the memory controller resources configurable
EDAC/ie31200: Simplify the pci_device_id table
EDAC/ie31200: Fix the 3rd parameter name of *populate_dimm_info()
EDAC/ie31200: Fix the error path order of ie31200_init()
EDAC/ie31200: Fix the DIMM size mask for several SoCs
EDAC/ie31200: Fix the size of EDAC_MC_LAYER_CHIP_SELECT layer
EDAC/device: Fix dev_set_name() format string
EDAC/pnd2: Make read-only const array intlv static
EDAC/igen6: Constify struct res_config
EDAC/amd64: Simplify return statement in dct_ecc_enabled()
EDAC: Update memory repair control interface for memory sparing feature
EDAC: Add a memory repair control feature
EDAC: Use string choice helper functions
EDAC: Add a Error Check Scrub control feature
...
|
|
Add the PCI-ID of the AQR105-based Tehuti TN4010 cards to allow loading
of the tn40xx driver on these cards. Here, I chose the detailed definition
with the subvendor ID similar to the QT2025 cards with the PCI-ID
TEHUTI:0x4022, because there is a card with an AQ2104 hiding amongst the
AQR105 cards, and they all come with the same PCI-ID (TEHUTI:0x4025). But
the AQ2104 is currently not supported.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-7-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prepare the tn40xx driver to load for Tehuti TN9510 cards, which require
bit 3 in the register TN40_REG_MDIO_CMD_STAT to be set. The function of bit
3 is unclear, but may have something to do with the length of the preamble
in the MDIO communication. If bit 3 is not set, the PHY will not be found
when performing a scan for PHYs. Use the available tn40_mdio_set_speed
function which includes setting bit 3. Just move the function to before the
devm_mdio_register function, which scans the mdio bus for PHYs.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: FUJITA Tomonori <fujita.tomonori@gmail.com>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-6-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In case of an AQR105-based device, create a software node for the mdio
function, with a child node for the Aquantia AQR105 PHY, providing a
firmware-name (and a bit more, which may be used for future checks) to
allow the PHY to load a MAC specific firmware from the file system.
The name of the PHY software node follows the naming convention suggested
in the patch for the mdiobus_scan function (in the same patch series).
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-5-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch makes functions that were provided for aqr107 applicable to
aqr105, or replaces generic functions with specific ones. Since the aqr105
was introduced before NBASE-T was defined (or 802.3bz), there are a number
of vendor specific registers involved in the definition of the
advertisement, in auto-negotiation and in the setting of the speed. The
functions have been written following the downstream driver for TN4010
cards with aqr105 PHY, and use code from aqr107 functions wherever it
seemed to make sense.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-4-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Allow the firmware name of an Aquantia PHY alternatively be provided by the
property "firmware-name" of a swnode. This software node may be provided by
the MAC or MDIO driver.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-3-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Re-use the AQR107 probe function to load the firmware on the AQR105 (and
to probe the HWMON).
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-2-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch will allow to use a swnode/fwnode defined for a phy_device. The
MDIO bus (mii_bus) needs to contain nodes for the PHY devices, named
"ethernet-phy@i", with i being the MDIO address (0 .. PHY_MAX_ADDR - 1).
The fwnode is only attached to the phy_device if there isn't already an
fwnode attached.
fwnode_get_named_child_node will increase the usage counter of the fwnode.
However, no new code is needed to decrease the counter again, since this is
already implemented in the phy_device_release function.
Signed-off-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250322-tn9510-v3a-v7-1-672a9a3d8628@gmx.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch adds support for running XDP programs on DQ, along with
rudimentary processing for XDP_DROP and XDP_PASS. These actions require
very limited driver functionality when it comes to processing an XDP
buffer, so currently if the XDP action is not XDP_PASS, the packet is
dropped and stats are updated.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaliginedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy<hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-7-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In order to support installing an XDP program on DQ, RX buffers need to
be reposted using 4K buffers, which is larger than the default packet
buffer size of 2K. This is needed to accommodate the extra head and tail
that accompanies the data portion of an XDP buffer. Continuing to use 2K
buffers would mean that the packet buffer size for the NIC would have to
be restricted to 2048 - 320 - 256 = 1472B. However, this is problematic
for two reasons: first, 1472 is not a packet buffer size accepted by
GVE; second, at least 1474B of buffer space is needed to accommodate an
MTU of 1460, which is the default on GCP. As such, we allocate 4K
buffers, and post a 2K section of those 4K buffers (offset relative to
the XDP headroom) to the NIC for DMA to avoid a potential extra copy.
Because the GQ-QPL datapath requires copies regardless, this change was
not needed to support XDP in that case.
To capture this subtlety, a new field, packet_buffer_truesize, has been
added to the rx ring struct to represent size of the allocated buffer,
while packet_buffer_size has been left to represent the portion of the
buffer posted to the NIC.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-6-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The data_buffer_size_dqo field in gve_priv and the packet_buffer_size
field in gve_rx_ring theoretically have the same meaning, but they are
defined in two different places and used in two separate contexts. There
is no good reason for this, so this change merges those fields into the
packet_buffer_size field in the RX ring.
This change also introduces a packet_buffer_size field to struct
gve_rx_queue_config to account for cases where queues are not allocated,
such as when the interface is down.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-5-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit ebdfae0d377b ("gve: adopt page pool for DQ RDA mode") introduced
a buf_size field to the gve_rx_slot_page_info struct, which can be used
in the datapath to take the place of the packet_buffer_size field, as it
will already be hot in the cache due to its extensive use. Using the
buf_size field in the datapath frees up the packet_buffer_size field in
the GQ-specific RX cacheline to be generalized for GQ and DQ (in the
next patch), as there is currently no common packet buffer size field
between the two queue formats.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-4-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An earlier patch series[1] introduced RX/TX ring allocation configuration
structs which contained metadata used to allocate and configure new RX
and TX rings. This led to a much cleaner and safer allocation pattern
wherein queue resources were not deallocated until new queue resources
were successfully allocated.
Migrate the XDP allocation path to use the same pattern to allow for the
existence of a single allocation path instead of relying on XDP-specific
allocation methods. These extra allocation methods result in the
duplication of many existing behaviors while being prone to error when
configuration changes unrelated to XDP occur.
Link: https://lore.kernel.org/netdev/20240122182632.1102721-1-shailend@google.com/ [1]
Reviewed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-3-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These statistics pollute the hotpath and do not have any real-world use
or meaning.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Joshua Washington <joshwash@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Link: https://patch.msgid.link/20250321002910.1343422-2-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If we fail to configure the MAC or PCS according to the desired mode,
do not allow the network link to come up until we have successfully
configured the MAC and PCS. This improves phylink's behaviour when an
error occurs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1twkqO-0006FI-Gm@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
"Nothing major this time around.
Apart from the usual perf/PMU updates, some page table cleanups, the
notable features are average CPU frequency based on the AMUv1
counters, CONFIG_HOTPLUG_SMT and MOPS instructions (memcpy/memset) in
the uaccess routines.
Perf and PMUs:
- Support for the 'Rainier' CPU PMU from Arm
- Preparatory driver changes and cleanups that pave the way for BRBE
support
- Support for partial virtualisation of the Apple-M1 PMU
- Support for the second event filter in Arm CSPMU designs
- Minor fixes and cleanups (CMN and DWC PMUs)
- Enable EL2 requirements for FEAT_PMUv3p9
Power, CPU topology:
- Support for AMUv1-based average CPU frequency
- Run-time SMT control wired up for arm64 (CONFIG_HOTPLUG_SMT). It
adds a generic topology_is_primary_thread() function overridden by
x86 and powerpc
New(ish) features:
- MOPS (memcpy/memset) support for the uaccess routines
Security/confidential compute:
- Fix the DMA address for devices used in Realms with Arm CCA. The
CCA architecture uses the address bit to differentiate between
shared and private addresses
- Spectre-BHB: assume CPUs Linux doesn't know about vulnerable by
default
Memory management clean-ups:
- Drop the P*D_TABLE_BIT definition in preparation for 128-bit PTEs
- Some minor page table accessor clean-ups
- PIE/POE (permission indirection/overlay) helpers clean-up
Kselftests:
- MTE: skip hugetlb tests if MTE is not supported on such mappings
and user correct naming for sync/async tag checking modes
Miscellaneous:
- Add a PKEY_UNRESTRICTED definition as 0 to uapi (toolchain people
request)
- Sysreg updates for new register fields
- CPU type info for some Qualcomm Kryo cores"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (72 commits)
arm64: mm: Don't use %pK through printk
perf/arm_cspmu: Fix missing io.h include
arm64: errata: Add newer ARM cores to the spectre_bhb_loop_affected() lists
arm64: cputype: Add MIDR_CORTEX_A76AE
arm64: errata: Add KRYO 2XX/3XX/4XX silver cores to Spectre BHB safe list
arm64: errata: Assume that unknown CPUs _are_ vulnerable to Spectre BHB
arm64: errata: Add QCOM_KRYO_4XX_GOLD to the spectre_bhb_k24_list
arm64/sysreg: Enforce whole word match for open/close tokens
arm64/sysreg: Fix unbalanced closing block
arm64: Kconfig: Enable HOTPLUG_SMT
arm64: topology: Support SMT control on ACPI based system
arch_topology: Support SMT control for OF based system
cpu/SMT: Provide a default topology_is_primary_thread()
arm64/mm: Define PTDESC_ORDER
perf/arm_cspmu: Add PMEVFILT2R support
perf/arm_cspmu: Generalise event filtering
perf/arm_cspmu: Move register definitons to header
arm64/kernel: Always use level 2 or higher for early mappings
arm64/mm: Drop PXD_TABLE_BIT
arm64/mm: Check pmd_table() in pmd_trans_huge()
...
|
|
The platform device driver data has not been used since commit
7a4ca51b7040 ("thermal/drivers/qcom-spmi: Use devm_iio_channel_get") so
drop the unnecessary assignment.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250228082936.5694-1-johan+linaro@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The hardware calibration is fused on some, but not all, Gen3 and Gen4
boards. The calibrations values are the same on both generations but
located at different register offsets.
Instead of having duplicated logic to read the and store the values
create structure to hold the register parameters and have a common
function do the reading.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250305174631.4119374-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The style of the driver is to use lowercase hex constants, correct the
few outlines.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20250305174631.4119374-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
BCM74110 uses a different process node compared to previous chips that
requires a different equation, account for that.
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20250116193842.758788-3-florian.fainelli@broadcom.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Only sensors that are valid need to have their interrupts enable status
updated based on their thresholds. Use the lvts_for_each_valid_sensor()
helper in lvts_update_irq_mask() to ignore invalid sensors.
Currently, since the invalid sensors will always contain zeroed out
thresholds (from kzalloc), they will always get their interrupts
disabled on this loop. So this commit doesn't change the resulting
interrupts configuration, but it slightly optimizes the loop by skipping
the invalid sensors, avoids potential future surprises if at some point
memory is no longer allocated for invalid sensors, as well as makes the
code more obvious.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250113-mt8192-lvts-filtered-suspend-fix-v2-5-07a25200c7c6@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Interrupts are enabled per sensor in lvts_update_irq_mask() as needed,
there's no point in enabling all of them during initialization. Change
the MONINT register initial value so all sensor interrupts start
disabled.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250113-mt8192-lvts-filtered-suspend-fix-v2-4-07a25200c7c6@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
In order to get working interrupts, a low offset value needs to be
configured. The minimum value for it is 20 Celsius, which is what is
configured when there's no lower thermal trip (ie the thermal core
passes -INT_MAX as low trip temperature). However, when the temperature
gets that low and fluctuates around that value it causes an interrupt
storm.
Prevent that interrupt storm by not enabling the low offset interrupt if
the low threshold is the minimum one.
Cc: stable@vger.kernel.org
Fixes: 77354eaef821 ("thermal/drivers/mediatek/lvts_thermal: Don't leave threshold zeroed")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250113-mt8192-lvts-filtered-suspend-fix-v2-3-07a25200c7c6@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The Stage 3 thermal threshold is currently configured during
the controller initialization to 105 Celsius. From the kernel
perspective, this configuration is harmful because:
* The stage 3 interrupt that gets triggered when the threshold is
crossed is not handled in any way by the IRQ handler, it just gets
cleared. Besides, the temperature used for stage 3 comes from the
sensors, and the critical thermal trip points described in the
Devicetree will already cause a shutdown when crossed (at a lower
temperature, of 100 Celsius, for all SoCs currently using this
driver).
* The only effect of crossing the stage 3 threshold that has been
observed is that it causes the machine to no longer be able to enter
suspend. Even if that was a result of a momentary glitch in the
temperature reading of a sensor (as has been observed on the
MT8192-based Chromebooks).
For those reasons, disable the Stage 3 thermal threshold configuration.
Cc: stable@vger.kernel.org
Reported-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Closes: https://lore.kernel.org/all/20241108-lvts-v1-1-eee339c6ca20@chromium.org/
Fixes: f5f633b18234 ("thermal/drivers/mediatek: Add the Low Voltage Thermal Sensor driver")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250113-mt8192-lvts-filtered-suspend-fix-v2-2-07a25200c7c6@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
When configured in filtered mode, the LVTS thermal controller will
monitor the temperature from the sensors and trigger an interrupt once a
thermal threshold is crossed.
Currently this is true even during suspend and resume. The problem with
that is that when enabling the internal clock of the LVTS controller in
lvts_ctrl_set_enable() during resume, the temperature reading can glitch
and appear much higher than the real one, resulting in a spurious
interrupt getting generated.
Disable the temperature monitoring and give some time for the signals to
stabilize during suspend in order to prevent such spurious interrupts.
Cc: stable@vger.kernel.org
Reported-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Closes: https://lore.kernel.org/all/20241108-lvts-v1-1-eee339c6ca20@chromium.org/
Fixes: 8137bb90600d ("thermal/drivers/mediatek/lvts_thermal: Add suspend and resume")
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20250113-mt8192-lvts-filtered-suspend-fix-v2-1-07a25200c7c6@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The mapping table for the rk3328 is missing the entry for -25C which is
found in the TRM section 9.5.2 "Temperature-to-code mapping".
NOTE: the kernel uses the tsadc_q_sel=1'b1 mode which is defined as:
4096-<code in table>. Whereas the table in the TRM gives the code
"3774" for -25C, the kernel uses 4096-3774=322.
[Dragan Simic] : "After going through the RK3308 and RK3328 TRMs, as
well as through the downstream kernel code, it seems we may have
some troubles at our hands. Let me explain, please.
To sum it up, part 1 of the RK3308 TRM v1.1 says on page 538 that
the equation for the output when tsadc_q_sel equals 1 is (4096 -
tsadc_q), while part 1 of the RK3328 TRM v1.2 says that the output
equation is (1024 - tsadc_q) in that case.
The downstream kernel code, however, treats the RK3308 and RK3328
tables and their values as being the same. It even mentions 1024 as
the "offset" value in a comment block for the rk_tsadcv3_control()
function, just like the upstream code does, which is obviously wrong
"offset" value when correlated with the table on page 544 of part 1
of the RK3308 TRM v1.1.
With all this in mind, it's obvious that more work is needed to make
it clear where's the actual mistake (it could be that the TRM is
wrong), which I'll volunteer for as part of the SoC binning project.
In the meantime, this patch looks fine as-is to me, by offering
what's a clear improvement to the current state of the upstream
code"
Link: https://opensource.rock-chips.com/images/9/97/Rockchip_RK3328TRM_V1.1-Part1-20170321.pdf
Cc: stable@vger.kernel.org
Fixes: eda519d5f73e ("thermal: rockchip: Support the RK3328 SOC in thermal driver")
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Link: https://lore.kernel.org/r/20250207175048.35959-1-twoerner@gmail.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
SoCs without RPM need to enable sensors and calibrate them from the kernel.
The IPQ5332 and IPQ5424 use the tsens v2.3.3 IP and do not have RPM.
Therefore, add a new calibration function for V2, as the tsens.c calib
function only supports V1. Also add new feature_config, ops and data for
IPQ5332, IPQ5424.
Although the TSENS IP supports 16 sensors, not all are used. The hw_id
is used to enable the relevant sensors.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Praveenkumar I <quic_ipkumar@quicinc.com>
Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
Link: https://lore.kernel.org/r/20250210120436.821684-3-quic_mmanikan@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Enable power-down of TMU (Thermal Management Unit) for TMU version 2 during
system suspend to save power. Save approximately 4.3mW on VDD_ANA_1P8 on
i.MX93 platforms.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241209164859.3758906-2-Frank.Li@nxp.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use dev_err_probe() and devm_clk_get_optional_enabled() to simplify the
code.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Link: https://lore.kernel.org/r/20241209164859.3758906-1-Frank.Li@nxp.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
* for-next/smt-control:
: Support SMT control on arm64
arm64: Kconfig: Enable HOTPLUG_SMT
arm64: topology: Support SMT control on ACPI based system
arch_topology: Support SMT control for OF based system
cpu/SMT: Provide a default topology_is_primary_thread()
|
