| Age | Commit message (Collapse) | Author |
|---|
|
The new MT8186 drive came in and the probe calls were
refactored at the same time. Fix it up. Fixes a build issue.
Cc: Guodong Liu <guodong.liu@mediatek.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull flexible-array transformations from Gustavo Silva:
"Treewide patch that replaces zero-length arrays with flexible-array
members.
This has been baking in linux-next for a whole development cycle"
* tag 'flexible-array-transformations-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
treewide: Replace zero-length arrays with flexible-array members
|
|
In addition to the RGB444 output, the BCM2711 HDMI controller supports
the YUV444 and YUV422 output formats.
Let's add support for them in the driver, but still use RGB as the
preferred format.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-8-maxime@cerno.tech
|
|
Currently we take the max_bpc property as the bpc value and do not try
anything else.
However, what the other drivers seem to be doing is that they would try
with the highest bpc allowed by the max_bpc property and the hardware
capabilities, test if it results in an acceptable configuration, and if
not decrease the bpc and try again.
Let's use the same logic.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-7-maxime@cerno.tech
|
|
The current code only base its decision for whether the scrambler must be
enabled or not on the pixel clock of the mode, but doesn't take the bits
per color into account.
Let's leverage the new function to compute the clock rate in the
scrambler setup code.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-6-maxime@cerno.tech
|
|
In the function that validates that the clock isn't too high, we've only
taken our controller limitations into account so far.
However, the sink can have a limit on the maximum TMDS clock it can deal
with too which is exposed through the EDID and the drm_display_info.
Make sure we check it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-5-maxime@cerno.tech
|
|
The code to compute our clock rate for a given setup will be called in
multiple places in the next patches, so let's create a separate function
for it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-4-maxime@cerno.tech
|
|
Our code is doing the same clock rate validation in multiple instances.
Let's create a helper to share the rate validation.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-3-maxime@cerno.tech
|
|
The pixel_rate field in the vc4_hdmi_connector_state struct actually
stores the TMDS character rate, let's rename it for consistency.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220222164042.403112-2-maxime@cerno.tech
|
|
If DRM_ITE_IT6505 is y but DRM_DP_HELPER is m, building failed:
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_i2c_remove':
ite-it6505.c:(.text+0x35c): undefined reference to `drm_dp_aux_unregister'
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_dpcd_read':
ite-it6505.c:(.text+0x420): undefined reference to `drm_dp_dpcd_read'
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_get_dpcd':
ite-it6505.c:(.text+0x4a4): undefined reference to `drm_dp_dpcd_read'
drivers/gpu/drm/bridge/ite-it6505.o: In function `it6505_dpcd_write':
ite-it6505.c:(.text+0x52c): undefined reference to `drm_dp_dpcd_write'
Select DRM_DP_HELPER for DRM_ITE_IT6505 to fix this.
Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220317094724.25972-1-yuehaibing@huawei.com
|
|
Drivers should never touch this directly.
v2: drop kerneldoc for now internal handling
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220321135856.1331-2-christian.koenig@amd.com
|
|
This function allows to replace fences from the shared fence list when
we can gurantee that the operation represented by the original fence has
finished or no accesses to the resources protected by the dma_resv
object any more when the new fence finishes.
Then use this function in the amdkfd code when BOs are unmapped from the
process.
v2: add an example when this is usefull.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220321135856.1331-1-christian.koenig@amd.com
|
|
Only an EDID CEA extension has byte #3, while the CTA DisplayID Data
Block does not. Don't interpret bogus data for color formats.
For most displays it's probably an unlikely scenario you'd have a CTA
DisplayID Data Block without a CEA extension, but they do exist.
Fixes: e28ad544f462 ("drm/edid: parse CEA blocks embedded in DisplayID")
Cc: <stable@vger.kernel.org>
Cc: Shawn C Lee <shawn.c.lee@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220323100438.1757295-1-jani.nikula@intel.com
|
|
Tag code stored in bit7:5 for CTA block byte[3] is not the same as
CEA extension block definition. Only check CEA block has
basic audio support.
v3: update commit message.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Shawn C Lee <shawn.c.lee@intel.com>
Cc: intel-gfx <intel-gfx@lists.freedesktop.org>
Signed-off-by: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Fixes: e28ad544f462 ("drm/edid: parse CEA blocks embedded in DisplayID")
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220324061218.32739-1-shawn.c.lee@intel.com
|
|
Use dma_resv_wait() instead of extracting the exclusive fence and
waiting on it manually.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Maor Gottlieb <maorg@nvidia.com>
Cc: Gal Pressman <galpress@amazon.com>
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220321135856.1331-4-christian.koenig@amd.com
|
|
We can get the excl fence together with the shared ones as well.
v2: rename the member to fences as well
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Russell King <linux+etnaviv@armlinux.org.uk>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: etnaviv@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20220321135856.1331-5-christian.koenig@amd.com
|
|
Adding the audio support on the HDMI bridge for I2S only.
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Signed-off-by: Andy.Hsieh <Andy.Hsieh@mediatek.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220316135733.173950-4-nbelin@baylibre.com
|
|
Set the register page length or window length to
0x100 according to the documentation.
Fixes: 988156dc2fc9 ("drm: bridge: add it66121 driver")
Signed-off-by: Nicolas Belin <nbelin@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220316135733.173950-3-nbelin@baylibre.com
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"After a somewhat quiet 5.17 release, the size of the DT changes is a
bit larger again. There are nine new SoC that get added, all of them
related to existing platforms:
- Airoha (formerly Mediatek/EcoNet) EN7523 networking SoC and EVB
- Mediatek mt6582 tablet platform with the Prestigio PMT5008 3G
tablet
- Microchip Lan966 networking SoC and it evaluation board
- Qualcomm Snapdragon 625/632 midrange phone SoCs, with the LG Nexus
5X and Fairphone FP3 phones
- Renesas RZ/G2LC and RZ/V2L general-purpose embedded SoCs, along
with their evaluation boards
- Samsung Exynos 850 phone SoC and reference board
- Samsung Exynos7885 with the Samsung Galaxy A8 (2018) phone
- Tesla FSD (Fully Self-Driving), an automotive SoC loosely derived
from the Samsung Exynos family.
- TI K3/AM62 SoC and reference board
Support for additional functionality in existing dts files is added
all over the place: Samsung, Renesas, Mstar, wpcm450, OMAP, AT91,
Allwinner, i.MX, Tegra, Aspeed, Oxnas, Qualcomm, Mediatek, and
Broadcom.
Samsung has a rework for its pinctrl schema that is a bit tricky and
requires driver changes to be included here.
A few more platforms only have smaller cleanups and DT Schema fixes,
this includes SoCFPGA, ux500, ixp4xx, STi, Xilinx Zynq, LG, and Juno.
The new machines are really too many to list, but I'll do it anyway:
Allwinner:
- A20-Marsboard development board
Amlogic:
- Amediatek X96-AIR (Amlogic S905X3)
- CYX A95XF3-AIR (Amlogic S905X3)
- Haochuangy H96-Max (Amlogic S905X3)
- Amlogic AQ222 (Amlogic S4)
- OSMC Vero 4K+ (Amlogic S905D)
Arm Juno:
- Separate DT depending on SCMI firmware version
Aspeed:
- Quanta S6Q BMC (AST2600)
- ASRock ROMED8HM3 (AST2500)
Broadcom:
- Raspberry Pi Zero 2 W
Marvell MVEBU/Armada:
- Ctera C200 V1 NAS (kirkwood)
- Ctera C200 V2 NAS (armada-370)
Mstar:
- DongShanPiOne, a low-end embedded board
- Miyoo Mini handheld game console
NXP i.MX:
- Numerous i.MX8M Mini based boards in even more variations, but
none based on other SoCs this time:
Protonic PRT8MM, emCON-MX8M Mini, Toradex Verdin, and
Gateworks GW7903
Qualcomm:
- Google Herobrine R1 Chromebook platform (Snapdragon 7c Gen 3)
- SHIFT6mq phone (Snapdragon 845)
- Samsung Galaxy Book2 (Snapdragon 850)
- Snapdragon 8 Gen 1 Hardware Development Kit
TI OMAP:
- SanCloud BeagleBone Enhanced WiFi
Rockchip:
- Pine64 PineNote ereader tablet (rk356x)
- Bananapi-R2-Pro (rk356x)
STM32:
- emtrion emSBS-Argon embedded board (stm32mp157c)"
* tag 'arm-dt-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (627 commits)
arm64: dts: n5x: drop invalid property and fix edac node name
arm64: dts: fsd: Add the MCT support
arm64: dts: stingray: Fix spi clock name
arm64: dts: ns2: Fix spi clock name
ARM: dts: rockchip: Update regulator name for PX3
ARM: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Add #clock-cells value for rk805
arm64: dts: rockchip: Remove vcc13 and vcc14 for rk808
arm64: dts: rockchip: Fix SDIO regulator supply properties on rk3399-firefly
ARM: dts: at91: sama7g5: Add NAND support
ARM: dts: at91: sama7g5: add eic node
ARM: dts: at91: sama7g5: Remove unused properties in i2c nodes
ARM: dts: at91: sam9x60ek: modify vdd_1v5 regulator to vdd_1v15
arm64: dts: lg: align pl330 node name with dtschema
arm64: dts: lg: add dma-cells to pl330 node
arm64: dts: juno: align pl330 node name with dtschema
arm64: dts: broadcom: Fix sata nodename
arm64: dts: n5x: add sdr edac support
arm64: dts: agilex/stratix10: add clock-names to USB DWC2 node
dt-bindings: usb: dwc2: add disable-over-current
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"There are a few separately maintained driver subsystems that we merge
through the SoC tree, notable changes are:
- Memory controller updates, mainly for Tegra and Mediatek SoCs, and
clarifications for the memory controller DT bindings
- SCMI firmware interface updates, in particular a new transport
based on OPTEE and support for atomic operations.
- Cleanups to the TEE subsystem, refactoring its memory management
For SoC specific drivers without a separate subsystem, changes include
- Smaller updates and fixes for TI, AT91/SAMA5, Qualcomm and NXP
Layerscape SoCs.
- Driver support for Microchip SAMA5D29, Tesla FSD, Renesas RZ/G2L,
and Qualcomm SM8450.
- Better power management on Mediatek MT81xx, NXP i.MX8MQ and older
NVIDIA Tegra chips"
* tag 'arm-drivers-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (154 commits)
ARM: spear: fix typos in comments
soc/microchip: fix invalid free in mpfs_sys_controller_delete
soc: s4: Add support for power domains controller
dt-bindings: power: add Amlogic s4 power domains bindings
ARM: at91: add support in soc driver for new SAMA5D29
soc: mediatek: mmsys: add sw0_rst_offset in mmsys driver data
dt-bindings: memory: renesas,rpc-if: Document RZ/V2L SoC
memory: emif: check the pointer temp in get_device_details()
memory: emif: Add check for setup_interrupts
dt-bindings: arm: mediatek: mmsys: add support for MT8186
dt-bindings: mediatek: add compatible for MT8186 pwrap
soc: mediatek: pwrap: add pwrap driver for MT8186 SoC
soc: mediatek: mmsys: add mmsys reset control for MT8186
soc: mediatek: mtk-infracfg: Disable ACP on MT8192
soc: ti: k3-socinfo: Add AM62x JTAG ID
soc: mediatek: add MTK mutex support for MT8186
soc: mediatek: mmsys: add mt8186 mmsys routing table
soc: mediatek: pm-domains: Add support for mt8186
dt-bindings: power: Add MT8186 power domains
soc: mediatek: pm-domains: Add support for mt8195
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"SoC specific code is generally used for older platforms that don't
(yet) use device tree to do the same things.
- Support is added for i.MXRT10xx, a Cortex-M7 based microcontroller
from NXP. At the moment this is still incomplete as other portions
are merged through different trees.
- Long abandoned support for running NOMMU ARMv4 or ARMv5 platforms
gets removed, now the Arm NOMMU platforms are limited to the
Cortex-M family of microcontrollers
- Two old PXA boards get removed, along with corresponding driver
bits.
- Continued cleanup of the Intel IXP4xx platforms, removing some
remnants of the old board files.
- Minor Cleanups and fixes for Orion, PXA, MMP, Mstar, Samsung
- CPU idle support for AT91
- A system controller driver for Polarfire"
* tag 'arm-soc-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (29 commits)
ARM: remove support for NOMMU ARMv4/v5
ARM: PXA: fix up decompressor code
soc: microchip: make mpfs_sys_controller_put static
ARM: pxa: remove Intel Imote2 and Stargate 2 boards
ARM: mmp: Fix failure to remove sram device
ARM: mstar: Select ARM_ERRATA_814220
soc: add microchip polarfire soc system controller
ARM: at91: Kconfig: select PM_OPP
ARM: at91: PM: add cpu idle support for sama7g5
ARM: at91: ddr: fix typo to align with datasheet naming
ARM: at91: ddr: align macro definitions
ARM: at91: ddr: remove CONFIG_SOC_SAMA7 dependency
ARM: ixp4xx: Convert to SPARSE_IRQ and P2V
ARM: ixp4xx: Drop all common code
ARM: ixp4xx: Drop custom DMA coherency and bouncing
ARM: ixp4xx: Remove feature bit accessors
net: ixp4xx_hss: Check features using syscon
net: ixp4xx_eth: Drop platform data support
soc: ixp4xx-npe: Access syscon regs using regmap
soc: ixp4xx: Add features from regmap helper
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three sets of updates for 5.18 in the asm-generic tree:
- The set_fs()/get_fs() infrastructure gets removed for good.
This was already gone from all major architectures, but now we can
finally remove it everywhere, which loses some particularly tricky
and error-prone code. There is a small merge conflict against a
parisc cleanup, the solution is to use their new version.
- The nds32 architecture ends its tenure in the Linux kernel.
The hardware is still used and the code is in reasonable shape, but
the mainline port is not actively maintained any more, as all
remaining users are thought to run vendor kernels that would never
be updated to a future release.
- A series from Masahiro Yamada cleans up some of the uapi header
files to pass the compile-time checks"
* tag 'asm-generic-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (27 commits)
nds32: Remove the architecture
uaccess: remove CONFIG_SET_FS
ia64: remove CONFIG_SET_FS support
sh: remove CONFIG_SET_FS support
sparc64: remove CONFIG_SET_FS support
lib/test_lockup: fix kernel pointer check for separate address spaces
uaccess: generalize access_ok()
uaccess: fix type mismatch warnings from access_ok()
arm64: simplify access_ok()
m68k: fix access_ok for coldfire
MIPS: use simpler access_ok()
MIPS: Handle address errors for accesses above CPU max virtual user address
uaccess: add generic __{get,put}_kernel_nofault
nios2: drop access_ok() check from __put_user()
x86: use more conventional access_ok() definition
x86: remove __range_not_ok()
sparc64: add __{get,put}_kernel_nofault()
nds32: fix access_ok() checks in get/put_user
uaccess: fix nios2 and microblaze get_user_8()
sparc64: fix building assembly files
...
|
|
Pull ARM updates from Russell King:
"Updates for IRQ stacks and virtually mapped stack support, and ftrace:
- Support for IRQ and vmap'ed stacks
This covers all the work related to implementing IRQ stacks and
vmap'ed stacks for all 32-bit ARM systems that are currently
supported by the Linux kernel, including RiscPC and Footbridge. It
has been submitted for review in four different waves:
- IRQ stacks support for v7 SMP systems [0]
- vmap'ed stacks support for v7 SMP systems[1]
- extending support for both IRQ stacks and vmap'ed stacks for all
remaining configurations, including v6/v7 SMP multiplatform
kernels and uniprocessor configurations including v7-M [2]
- fixes and updates in [3]
- ftrace fixes and cleanups
Make all flavors of ftrace available on all builds, regardless of
ISA choice, unwinder choice or compiler [4]:
- use ADD not POP where possible
- fix a couple of Thumb2 related issues
- enable HAVE_FUNCTION_GRAPH_FP_TEST for robustness
- enable the graph tracer with the EABI unwinder
- avoid clobbering frame pointer registers to make Clang happy
- Fixes for the above"
[0] https://lore.kernel.org/linux-arm-kernel/20211115084732.3704393-1-ardb@kernel.org/
[1] https://lore.kernel.org/linux-arm-kernel/20211122092816.2865873-1-ardb@kernel.org/
[2] https://lore.kernel.org/linux-arm-kernel/20211206164659.1495084-1-ardb@kernel.org/
[3] https://lore.kernel.org/linux-arm-kernel/20220124174744.1054712-1-ardb@kernel.org/
[4] https://lore.kernel.org/linux-arm-kernel/20220203082204.1176734-1-ardb@kernel.org/
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (62 commits)
ARM: fix building NOMMU ARMv4/v5 kernels
ARM: unwind: only permit stack switch when unwinding call_with_stack()
ARM: Revert "unwind: dump exception stack from calling frame"
ARM: entry: fix unwinder problems caused by IRQ stacks
ARM: unwind: set frame.pc correctly for current-thread unwinding
ARM: 9184/1: return_address: disable again for CONFIG_ARM_UNWIND=y
ARM: 9183/1: unwind: avoid spurious warnings on bogus code addresses
Revert "ARM: 9144/1: forbid ftrace with clang and thumb2_kernel"
ARM: mach-bcm: disable ftrace in SMC invocation routines
ARM: cacheflush: avoid clobbering the frame pointer
ARM: kprobes: treat R7 as the frame pointer register in Thumb2 builds
ARM: ftrace: enable the graph tracer with the EABI unwinder
ARM: unwind: track location of LR value in stack frame
ARM: ftrace: enable HAVE_FUNCTION_GRAPH_FP_TEST
ARM: ftrace: avoid unnecessary literal loads
ARM: ftrace: avoid redundant loads or clobbering IP
ARM: ftrace: use trampolines to keep .init.text in branching range
ARM: ftrace: use ADD not POP to counter PUSH at entry
ARM: ftrace: ensure that ADR takes the Thumb bit into account
ARM: make get_current() and __my_cpu_offset() __always_inline
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been a fairly calm development cycle. There are a few last-minute
ALSA core fixes, most notably for covering PCM ioctl races, but the
most of rest are device-specific changes.
Below are some highlights:
ALSA core:
- Fixes for PCM ioctl races that may lead to UAF
- Fix for oversized allocations in PCM OSS layer
ASoC:
- Start of moving SoF to support multiple IPC mechanisms
- Use of NHLT ACPI table to reduce the amount of quirking required
for Intel systems
- Preliminary works forthcoming Intel AVS driver for legacy Intel DSP
firmwares
- Support for AMD PDM, Atmel PDMC, Awinic AW8738, i.MX cards with
TLV320AIC31xx, Intel machines with CS35L41 and ESSX8336, Mediatek
MT8181 wideband bluetooth, nVidia Tegra234, Qualcomm SC7280,
Renesas RZ/V2L, Texas Instruments TAS585M
HD-audio:
- Driver re-binding fix for HD-audio
- Updates for Intel ADL and Tegra234, various platform quirks for
Dell, HP, Lenovo, ASUS, Samsung and Clevo machines
USB-audio:
- Quirk updates for Scarlett2, RODE, Corsair devices"
* tag 'sound-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (486 commits)
ALSA: hda/realtek: Add alc256-samsung-headphone fixup
ALSA: pci: fix reading of swapped values from pcmreg in AC97 codec
ALSA: pcm: Add stream lock during PCM reset ioctl operations
ALSA: pcm: Fix races among concurrent prealloc proc writes
ALSA: pcm: Fix races among concurrent prepare and hw_params/hw_free calls
ALSA: pcm: Fix races among concurrent read/write and buffer changes
ALSA: pcm: Fix races among concurrent hw_params and hw_free calls
ASoC: atmel: mchp-pdmc: print the correct property name
MAINTAINERS: Add Shengjiu to maintainer list of sound/soc/fsl
ASoC: SOF: Add a new dai_get_clk topology IPC op
ASoC: SOF: topology: Add ops for setting up and tearing down pipelines
ASoC: SOF: expose sof_route_setup()
ASoC: SOF: Add dai_link_fixup PCM op for IPC3
ASoC: SOF: Add trigger PCM op for IPC3
ASoC: SOF: Define hw_params PCM op for IPC3
ASoC: SOF: Introduce IPC3 PCM hw_free op
ASoC: SOF: pcm: expose the sof_pcm_setup_connected_widgets() function
ASoC: SOF: Introduce IPC-specific PCM ops
ASoC: SOF: Add bytes_ext control IPC ops for IPC3
ASoC: SOF: Add bytes_get/put control IPC ops for IPC3
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- a major reorg at platform Kconfig/Makefile files, organizing them per
vendor. The other media Kconfig/Makefile files also sorted
- New sensor drivers: hi847, isl7998x, ov08d10
- New Amphion vpu decoder stateful driver
- New Atmel microchip csi2dc driver
- tegra-vde driver promoted from staging
- atomisp: some fixes for it to work on BYT
- imx7-mipi-csis driver promoted from staging and renamed
- camss driver got initial support for VFE hardware version Titan 480
- mtk-vcodec has gained support for MT8192
- lots of driver changes, fixes and improvements
* tag 'media/v5.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (417 commits)
media: nxp: Restrict VIDEO_IMX_MIPI_CSIS to ARCH_MXC or COMPILE_TEST
media: amphion: cleanup media device if register it fail
media: amphion: fix some issues to improve robust
media: amphion: fix some error related with undefined reference to __divdi3
media: amphion: fix an issue that using pm_runtime_get_sync incorrectly
media: vidtv: use vfree() for memory allocated with vzalloc()
media: m5mols/m5mols.h: document new reset field
media: pixfmt-yuv-planar.rst: fix PIX_FMT labels
media: platform: Remove unnecessary print function dev_err()
media: amphion: Add missing of_node_put() in vpu_core_parse_dt()
media: mtk-vcodec: Add missing of_node_put() in mtk_vdec_hw_prob_done()
media: platform: amphion: Fix build error without MAILBOX
media: spi: Kconfig: Place SPI drivers on a single menu
media: i2c: Kconfig: move camera drivers to the top
media: atomisp: fix bad usage at error handling logic
media: platform: rename mediatek/mtk-jpeg/ to mediatek/jpeg/
media: media/*/Kconfig: sort entries
media: Kconfig: cleanup VIDEO_DEV dependencies
media: platform/*/Kconfig: make manufacturer menus more uniform
media: platform: Create vendor/{Makefile,Kconfig} files
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev
Pull fbdev updates from Helge Deller:
"Lots of small fixes and code cleanups across most of the fbdev
drivers.
This includes conversions to use helper functions, const conversions,
spelling fixes, help text updates, adding return value checks, small
build fixes, and much more"
* tag 'for-5.18/fbdev-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: (59 commits)
video: fbdev: kyro: make read-only array ODValues static const
video: fbdev: offb: fix warning comparing pointer to 0
video: fbdev: omapfb: Add missing of_node_put() in dvic_probe_of
video: fbdev: sm712fb: Fix crash in smtcfb_write()
video: fbdev: s3c-fb: fix platform_get_irq.cocci warning
video: fbdev: sm712fb: Fix crash in smtcfb_read()
video: fbdev: via: check the return value of kstrdup()
video: fbdev: au1100fb: Spelling s/palette/palette/
video: fbdev: atari: Atari 2 bpp (STe) palette bugfix
video: fbdev: atari: Remove unused atafb_setcolreg()
video: fbdev: atari: Convert to standard round_up() helper
video: fbdev: atari: Fix TT High video mode
video: fbdev: udlfb: replace snprintf in show functions with sysfs_emit
video: fbdev: omapfb: panel-tpo-td043mtea1: Use sysfs_emit() instead of snprintf()
video: fbdev: omapfb: panel-dsi-cm: Use sysfs_emit() instead of snprintf()
video: fbdev: omapfb: Use sysfs_emit() instead of snprintf()
video: fbdev: s3c-fb: Use platform_get_irq() to get the interrupt
video: fbdev: Fix wrong file path for pvr2fb.c in Kconfig help text
video: fbdev: pxa3xx-gcu: Remove unnecessary print function dev_err()
video: fbdev: pxa168fb: Remove unnecessary print function dev_err()
...
|
|
Pull MMC updates from Ulf Hansson:
"MMC core:
- Convert to sysfs_emit() in favor of sprintf()
- Improve fallback to speed modes if eMMC HS200 fails
MMC host:
- dw_mmc: Allow variants to set minimal supported clock rate
- dw-mmc-rockchip: Fix problems with invalid clock rates
- litex_mmc: Add new DT based driver for the LiteX's LiteSDCard
interface
- litex_mmc: Add Gabriel Somlo and Joel Stanley as co-maintainers for
LiteX
- mtk-sd: Add support for the Mediatek MT8186 variant
- renesas_sdhi: Add support for RZ/G2UL variant
- renesas_sdhi: Add support for RZ/V2L variant
- rtsx_pci: Adjust power-on sequence to conform to the SD spec
- sdhci-am654: Add support for TI's AM62 variant
- sdhci_am654: Fixup support for TI's AM64 variant
- sdhci-esdhc-imx: Add support for the imx93 variant
- sdhci-msm: Add support for the msm8953 variant
- sdhci-pci-gli: Add support for runtime PM for the GL9763E variant
- sdhci-pci-gli: Adjustments of the SSC function for the GL975x
variants
- sdhci-tegra: Add support for wake on SD card event
- sunxi-mmc: Add support for Allwinner's F1c100s variant
- sunxi-mmc: Add support for D1 MMC variant"
* tag 'mmc-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (37 commits)
dt-bindings: mmc: renesas,sdhi: Document RZ/G2UL SoC
mmc: tmio: remove outdated members from host struct
mmc: mtk-sd: Silence delay phase calculation debug log
mmc: davinci_mmc: Handle error for clk_enable
mmc: sdhci-pci-gli: Add runtime PM for GL9763E
mmc: core: Drop HS400 caps unless 8-bit bus is supported too
mmc: host: Return an error when ->enable_sdio_irq() ops is missing
mmc: core: Improve fallback to speed modes if eMMC HS200 fails
dt-bindings: mmc: sunxi: add Allwinner F1c100s compatible
mmc: dw-mmc-rockchip: Fix handling invalid clock rates
mmc: dw_mmc: Support setting f_min from host drivers
mmc: host: Drop commas after SoC match table sentinels
mmc: rtsx: add 74 Clocks in power on flow
dt-bindings: mmc: renesas,sdhi: Document RZ/V2L SoC
mmc: sh_mmcif: Simplify division/shift logic
mmc: sdhci_am654: Add Support for TI's AM62 SoC
dt-bindings: mmc: imx-esdhc: Add imx93 compatible string
dt-bindings: mmc: sdhci-am654: Add compatible string for AM62 SoC
mmc: sdhci_am654: Fix the driver data of AM64 SoC
mmc: core: use sysfs_emit() instead of sprintf()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata updates from Damien Le Moal:
"For this cycle, no big change but many small fixes and code cleanup to
libata, the ahci driver and various pata drivers. In more details:
- Code simplification in pata_platform using
platform_get_mem_or_io(), from Lad.
- Fix read-only arrays declarations as const in pata_atiixp and
pata_pdc202xx_old, from Colin.
- Various cleanups and code simplification in libata-scsi, from me.
- Remove dead code in libata-acpi, from Sergey.
- Skip device scan deboune delay for Marvell 88SE9235 adapters (ahci)
to speedup boot, from Paul.
- Simplify functions declaration and use for functions always
returning 0 in libata-core, from Sergey.
- Non-fatal error fixes and in the pata_hpt366 and pata_hpt3x2n
drivers, from Sergey.
- Various code cleanup in the pata_artop, pata_hpt37x, pata_hpt366,
pata_hpt3x2n, pata_samsung_cf and sata_rcar drivers, from Sergey.
- Some libata-sff and libata-scsi code cleanup (e.g. change functions
to return "bool"), from Sergey.
- Renae ahci_board_mobile to board_ahci_low_power to be more
descriptive of the feature as that is also used on PC and server
AHCI adapters, from Mario.
- Cleanup of OF match tables, from Geert.
- Simplify the pata_pxa driver initialization using
platform_get_irq(), from Minghao"
* tag 'ata-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: (38 commits)
ata: pata_pxa: Use platform_get_irq() to get the interrupt
ata: Drop commas after OF match table sentinels
ata: ahci: Rename CONFIG_SATA_LPM_MOBILE_POLICY configuration item
ata: ahci: Rename `AHCI_HFLAG_IS_MOBILE`
ata: ahci: Rename board_ahci_mobile
ata: pata_hpt37x: merge transfer mode setting methods
ata: libata-sff: use *switch* statement in ata_sff_dev_classify()
ata: add/use ata_taskfile::{error|status} fields
ata: Kconfig: fix sata gemini compile test condition
ata: libata-scsi: use *switch* statements to check SCSI command codes
ata: libata-sff: refactor ata_sff_altstatus()
ata: libata-sff: refactor ata_sff_set_devctl()
ata: libata-sff: make ata_resources_present() return 'bool'
ata: pata_hpt3x2n: disable fast interrupts in prereset() method
ata: pata_hpt37x: disable fast interrupts in prereset() method
ata: pata_hpt366: disable fast interrupts in prereset() method
ata: pata_mpc52xx: use GFP_KERNEL
ata: sata_rcar: drop unused #define's
ata: pata_hpt366: check channel enable bits
ata: sata_rcar: make sata_rcar_ata_devchk() return 'bool'
...
|
|
The following build failure occurs when CONFIG_PERF_EVENTS is not set
as generic pmu functions are not visible in that scenario.
|-- s390-randconfig-r044-20220313
| |-- nd_perf.c:(.text):undefined-reference-to-perf_pmu_migrate_context
| |-- nd_perf.c:(.text):undefined-reference-to-perf_pmu_register
| `-- nd_perf.c:(.text):undefined-reference-to-perf_pmu_unregister
Similar build failure in nds32 architecture:
nd_perf.c:(.text+0x21e): undefined reference to `perf_pmu_migrate_context'
nd_perf.c:(.text+0x434): undefined reference to `perf_pmu_register'
nd_perf.c:(.text+0x57c): undefined reference to `perf_pmu_unregister'
Fix this issue by adding check for CONFIG_PERF_EVENTS config option
and disabling the nvdimm perf interface incase this config is not set.
Also remove function declaration of perf_pmu_migrate_context,
perf_pmu_register, perf_pmu_unregister functions from nd.h as these are
common pmu functions which are part of perf_event.h and since we
are disabling nvdimm perf interface incase CONFIG_PERF_EVENTS option
is not set, we not need to declare them in nd.h
Also move the platform_device header file addition part from nd.h to
nd_perf.c and add stub functions for register_nvdimm_pmu and
unregister_nvdimm_pmu functions to handle CONFIG_PERF_EVENTS=n
case.
Fixes: 0fab1ba6ad6b ("drivers/nvdimm: Add perf interface to expose nvdimm performance stats") (Commit id based on libnvdimm-for-next tree)
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Link: https://lore.kernel.org/all/62317124.YBQFU33+s%2FwdvWGj%25lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220323164550.109768-1-kjain@linux.ibm.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
uie_unsupported is not used by any drivers anymore, remove it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-29-alexandre.belloni@bootlin.com
|
|
Remove bogus use of uie_unsupported.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-28-alexandre.belloni@bootlin.com
|
|
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-27-alexandre.belloni@bootlin.com
|
|
Set RTC_FEATURE_ALARM_RES_MINUTE, so the core knows alarms have a
resolution of a minute. Also, the core will properly round down the alarm
instead of up.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-26-alexandre.belloni@bootlin.com
|
|
Switch to devm_rtc_allocate_device/devm_rtc_register_device, this allows
for further improvement of the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-25-alexandre.belloni@bootlin.com
|
|
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Also the driver doesn't supports UIE because it doesn't handle interrupts
so set RTC_FEATURE_ALARM_WAKEUP_ONLY,.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-24-alexandre.belloni@bootlin.com
|
|
Switch to devm_rtc_allocate_device/devm_rtc_register_device, this allows
for further improvement of the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-23-alexandre.belloni@bootlin.com
|
|
The reference manual doesn't specify whether the registers are latched and
they probably aren't, ensure the read time and date are consistent.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220309162301.61679-21-alexandre.belloni@bootlin.com
|
|
Since commitc9f5c7e7a84f ("rtc: rtc-spear: Provide flag for no support of
UIE mode") which was in 2012, the core changed a lot and UIE are now
supported using regular alarms. Drop uie_unsupported now to reflect that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220309162301.61679-20-alexandre.belloni@bootlin.com
|
|
While the RTC can store dates from year 0000 to 9999, leap years where not
tested fro 2100. The driver currently stores tm_year directly which will
probably fail at that time or more probably in 2300.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220309162301.61679-19-alexandre.belloni@bootlin.com
|
|
Switch to devm_rtc_allocate_device/devm_rtc_register_device, this allows
for further improvement of the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20220309162301.61679-18-alexandre.belloni@bootlin.com
|
|
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-17-alexandre.belloni@bootlin.com
|
|
Set RTC_FEATURE_ALARM_RES_MINUTE, so the core knows alarms have a
resolution of a minute. Also, the core will properly round down the alarm
instead of up.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-16-alexandre.belloni@bootlin.com
|
|
Set RTC_FEATURE_ALARM_RES_MINUTE, so the core knows alarms have a
resolution of a minute. Also, the core will properly round down the alarm
instead of up.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-15-alexandre.belloni@bootlin.com
|
|
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-14-alexandre.belloni@bootlin.com
|
|
The PCF85063 doesn't support UIE because setting an alarm to fire every
second confuses the chip and the fastest we can go is an alarm every 2
seconds.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-13-alexandre.belloni@bootlin.com
|
|
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-12-alexandre.belloni@bootlin.com
|
|
The PCF2127 doesn't support UIE because setting an alarm to fire every
second confuses the chip and the fastest we can go is an alarm every 2
seconds.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-11-alexandre.belloni@bootlin.com
|
|
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-10-alexandre.belloni@bootlin.com
|
|
Alarms have a resolution of a minute.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-9-alexandre.belloni@bootlin.com
|
|
Stop using uie_unsupported and clear RTC_FEATURE_UPDATE_INTERRUPT instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220309162301.61679-8-alexandre.belloni@bootlin.com
|
