| Age | Commit message (Collapse) | Author |
|---|
|
When memory encryption is active the device is likely not in a direct
mapped domain. Forbid using IOMMUv2 functionality for now until finer
grained checks for this have been implemented.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200824105415.21000-3-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Do not force devices supporting IOMMUv2 to be direct mapped when memory
encryption is active. This might cause them to be unusable because their
DMA mask does not include the encryption bit.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200824105415.21000-2-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The BD718(37/47/50) regulator enable states can be controlled
either by SW or by PMIC internal state machine. The bd718x7
driver has not supported leaving the regulators under HW state
machine control (except for cases where this is required to
avoid boot-up problems due to critical regulators being turned
OFF at reset when SNVS used as reset state).
On some systems this is undesirable as there now are setups where
mixture of SW and HW state machine controlled regulators is needed.
Specifically, some SoCs signal SUSPEND state change to PMIC via
STBY_REQ line. Now there are setups that expect certain regulators
then to be disabled (by PMIC state machine) while other regulators
should stay enabled (regardless of HW state => SW control required).
Add support for a new device-tree property
"rohm,no-regulator-enable-control" which can be used to leave
regulator(s) under HW state machine control.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/6ebba33dd08f2dcc9f1137bbff4d2dc905278a5a.1599029335.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BD718x7 driver initialized common configs for all regulators.
Simplify initialization by moving the initialization of common configs
out of the loop.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/2d3e68c94d4813410da8c4c7eac3332d167d19a8.1599029334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When using 128-bit interrupt-remapping table entry (IRTE) (a.k.a GA mode),
current driver disables interrupt remapping when it updates the IRTE
so that the upper and lower 64-bit values can be updated safely.
However, this creates a small window, where the interrupt could
arrive and result in IO_PAGE_FAULT (for interrupt) as shown below.
IOMMU Driver Device IRQ
============ ===========
irte.RemapEn=0
...
change IRTE IRQ from device ==> IO_PAGE_FAULT !!
...
irte.RemapEn=1
This scenario has been observed when changing irq affinity on a system
running I/O-intensive workload, in which the destination APIC ID
in the IRTE is updated.
Instead, use cmpxchg_double() to update the 128-bit IRTE at once without
disabling the interrupt remapping. However, this means several features,
which require GA (128-bit IRTE) support will also be affected if cmpxchg16b
is not supported (which is unprecedented for AMD processors w/ IOMMU).
Fixes: 880ac60e2538 ("iommu/amd: Introduce interrupt remapping ops structure")
Reported-by: Sean Osborne <sean.m.osborne@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Erik Rockstrom <erik.rockstrom@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/20200903093822.52012-3-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Currently, the RemapEn (valid) bit is accidentally cleared when
programming IRTE w/ guestMode=0. It should be restored to
the prior state.
Fixes: b9fc6b56f478 ("iommu/amd: Implements irq_set_vcpu_affinity() hook to setup vapic mode for pass-through devices")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/20200903093822.52012-2-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The user-after-free bug in thermal_zone_device_unregister() is reported by
KASAN. It happens because struct thermal_zone_device is released during of
device_unregister() invocation, and hence the "tz" variable shouldn't be
touched by thermal_notify_tz_delete(tz->id).
Fixes: 55cdf0a283b8 ("thermal: core: Add notifications call in the framework")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200817235854.26816-1-digetx@gmail.com
|
|
Currently driver is suppressing the negative temperature
readings from the vadc. Consumers of the thermal zones need
to read the negative temperature too. Don't suppress the
readings.
Fixes: c610afaa21d3c6e ("thermal: Add QPNP PMIC temperature alarm driver")
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/944856eb819081268fab783236a916257de120e4.1596040416.git.gurus@codeaurora.org
|
|
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54d7 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
|
|
The dev_iommu_priv_set() must be called after probe_device(). This fixes
a NULL pointer deference bug when booting a system with kernel cmdline
"intel_iommu=on,igfx_off", where the dev_iommu_priv_set() is abused.
The following stacktrace was produced:
Command line: BOOT_IMAGE=/isolinux/bzImage console=tty1 intel_iommu=on,igfx_off
...
DMAR: Host address width 39
DMAR: DRHD base: 0x000000fed90000 flags: 0x0
DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e
DMAR: DRHD base: 0x000000fed91000 flags: 0x1
DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
DMAR: RMRR base: 0x0000009aa9f000 end: 0x0000009aabefff
DMAR: RMRR base: 0x0000009d000000 end: 0x0000009f7fffff
DMAR: No ATSR found
BUG: kernel NULL pointer dereference, address: 0000000000000038
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.9.0-devel+ #2
Hardware name: LENOVO 20HGS0TW00/20HGS0TW00, BIOS N1WET46S (1.25s ) 03/30/2018
RIP: 0010:intel_iommu_init+0xed0/0x1136
Code: fe e9 61 02 00 00 bb f4 ff ff ff e9 57 02 00 00 48 63 d1 48 c1 e2 04 48
03 50 20 48 8b 12 48 85 d2 74 0b 48 8b 92 d0 02 00 00 48 89 7a 38 ff c1
e9 15 f5 ff ff 48 c7 c7 60 99 ac a7 49 c7 c7 a0
RSP: 0000:ffff96d180073dd0 EFLAGS: 00010282
RAX: ffff8c91037a7d20 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffffffffff
RBP: ffff96d180073e90 R08: 0000000000000001 R09: ffff8c91039fe3c0
R10: 0000000000000226 R11: 0000000000000226 R12: 000000000000000b
R13: ffff8c910367c650 R14: ffffffffa8426d60 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8c9107480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000038 CR3: 00000004b100a001 CR4: 00000000003706e0
Call Trace:
? _raw_spin_unlock_irqrestore+0x1f/0x30
? call_rcu+0x10e/0x320
? trace_hardirqs_on+0x2c/0xd0
? rdinit_setup+0x2c/0x2c
? e820__memblock_setup+0x8b/0x8b
pci_iommu_init+0x16/0x3f
do_one_initcall+0x46/0x1e4
kernel_init_freeable+0x169/0x1b2
? rest_init+0x9f/0x9f
kernel_init+0xa/0x101
ret_from_fork+0x22/0x30
Modules linked in:
CR2: 0000000000000038
---[ end trace 3653722a6f936f18 ]---
Fixes: 01b9d4e21148c ("iommu/vt-d: Use dev_iommu_priv_get/set()")
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Reported-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Link: https://lore.kernel.org/linux-iommu/96717683-70be-7388-3d2f-61131070a96a@secunet.com/
Link: https://lore.kernel.org/r/20200903065132.16879-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The VT-d spec requires (10.4.4 Global Command Register, GCMD_REG General
Description) that:
If multiple control fields in this register need to be modified, software
must serialize the modifications through multiple writes to this register.
However, in irq_remapping.c, modifications of IRE and CFI are done in one
write. We need to do two separate writes with STS checking after each. It
also checks the status register before writing command register to avoid
unnecessary register write.
Fixes: af8d102f999a4 ("x86/intel/irq_remapping: Clean up x2apic opt-out security warning mess")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Kevin Tian <kevin.tian@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Link: https://lore.kernel.org/r/20200828000615.8281-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Unlike we previously thought, the per-pixel alpha is just as broken on the
A20 as it is on the A10. Remove the quirk that says we can use it.
Fixes: dcf496a6a608 ("drm/sun4i: sun4i: Introduce a quirk for lowest plane alpha support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728134810.883457-2-maxime@cerno.tech
|
|
Unlike what we previously thought, only the per-pixel alpha is broken on
the lowest plane and the per-plane alpha isn't. Remove the check on the
alpha property being set on the lowest plane to reject a mode.
Fixes: dcf496a6a608 ("drm/sun4i: sun4i: Introduce a quirk for lowest plane alpha support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Cc: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200728134810.883457-1-maxime@cerno.tech
|
|
Function sun8i_vi_layer_get_csc_mode() is supposed to return CSC mode
but due to inproper return type (bool instead of u32) it returns just 0
or 1. Colors are wrong for YVU formats because of that.
Fixes: daab3d0e8e2b ("drm/sun4i: de2: csc_mode in de2 format struct is mostly redundant")
Reported-by: Roman Stratiienko <r.stratiienko@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Roman Stratiienko <r.stratiienko@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200901220305.6809-1-jernej.skrabec@siol.net
|
|
To be used in order to create foreign mappings. This is based on the
ZONE_DEVICE facility which is used by persistent memory devices in
order to create struct pages and kernel virtual mappings for the IOMEM
areas of such devices. Note that on kernels without support for
ZONE_DEVICE Xen will fallback to use ballooned pages in order to
create foreign mappings.
The newly added helpers use the same parameters as the existing
{alloc/free}_xenballooned_pages functions, which allows for in-place
replacement of the callers. Once a memory region has been added to be
used as scratch mapping space it will no longer be released, and pages
returned are kept in a linked list. This allows to have a buffer of
pages and prevents resorting to frequent additions and removals of
regions.
If enabled (because ZONE_DEVICE is supported) the usage of the new
functionality untangles Xen balloon and RAM hotplug from the usage of
unpopulated physical memory ranges to map foreign pages, which is the
correct thing to do in order to avoid mappings of foreign pages depend
on memory hotplug.
Note the driver is currently not enabled on Arm platforms because it
would interfere with the identity mapping required on some platforms.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20200901083326.21264-4-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
This is in preparation for the logic behind MEMORY_DEVICE_DEVDAX also
being used by non DAX devices.
No functional change intended.
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Link: https://lore.kernel.org/r/20200901083326.21264-3-roger.pau@citrix.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
The endianness marking on the variable v in meson_cipher is wrong.
It is actually in CPU-order, not little-endian.
This patch fixes it.
Fixes: 3d04158814e7 ("crypto: amlogic - enable working on big...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Corentin Labbe <clabbe@baylibre.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Remove redundant memzero_explicit() in sun8i_ss_cipher() before calling
kfree_sensitive(). kfree_sensitive() will zero the memory with
memzero_explicit().
Fixes: 453431a54934 ("mm, treewide: rename kzfree() to kfree_sensitive()")
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use kfree_sensitive() instead of open-coding it.
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use kfree_sensitive() instead of open-coding it.
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use kfree_sensitive() instead of open-coding it.
Signed-off-by: Denis Efremov <efremov@linux.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Use kfree_sensitive() instead of open-coding it.
Signed-off-by: Denis Efremov <efremov@linux.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Hadar Gat <hadar.gat@arm.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
|
|
A couple of minor fixes to the display changes that went in for 5.9.
The most important of which is a workaround for a HW bug that was
exposed by better push buffer space management, leading to
random(ish...) display engine hangs.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CACAvsv5QDxyMihrxbPk+-sORnaYtjR6_dbM68gEhb2wxht_G1w@mail.gmail.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.9-rc4:
- Clang build warning fix
- HDCP fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87sgbz2pnx.fsf@intel.com
|
|
BLK_MQ_F_TAG_SHARED actually means that tags is shared among request
queues, all of which should belong to LUNs attached to same HBA.
So rename it to make the point explicitly.
[jpg: rebase a few times, add rnbd-clt.c change]
Suggested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Small BW votes that translate to less than a single BCM unit are
currently truncated to zero. Ensure that non-zero BW requests always
result in at least a vote of 1 to BCM.
Fixes: 976daac4a1c5 ("interconnect: qcom: Consolidate interconnect RPMh support")
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
Link: https://lore.kernel.org/r/20200903192149.30385-2-mdtipton@codeaurora.org
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
|
|
If tg3_reset_task() fails, the device state is left in an inconsistent
state with IFF_RUNNING still set but NAPI state not enabled. A
subsequent operation, such as ifdown or AER error can cause it to
soft lock up when it tries to disable NAPI state.
Fix it by bringing down the device to !IFF_RUNNING state when
tg3_reset_task() fails. tg3_reset_task() running from workqueue
will now call tg3_close() when the reset fails. We need to
modify tg3_reset_task_cancel() slightly to avoid tg3_close()
calling cancel_work_sync() to cancel tg3_reset_task(). Otherwise
cancel_work_sync() will wait forever for tg3_reset_task() to
finish.
Reported-by: David Christensen <drc@linux.vnet.ibm.com>
Reported-by: Baptiste Covolato <baptiste@arista.com>
Fixes: db2199737990 ("tg3: Schedule at most one tg3_reset_task run")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TVE200 will occasionally print a bunch of lost interrupts
and similar dmesg messages, sometimes during boot and sometimes
after disabling and coming back to enablement. This is probably
because the hardware is left in an unknown state by the boot
loader that displays a logo.
This can be fixed by bringing the controller into a known state
by resetting the controller while enabling it. We retry reset 5
times like the vendor driver does. We also put the controller
into reset before de-clocking it and clear all interrupts before
enabling the vblank IRQ.
This makes the video enable/disable/enable cycle rock solid
on the D-Link DIR-685. Tested extensively.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200820203144.271081-1-linus.walleij@linaro.org
|
|
When calling __generic_fsdax_supported(), a dax-unsupported device may
not have dax_dev as NULL, e.g. the dax related code block is not enabled
by Kconfig.
Therefore in __generic_fsdax_supported(), to check whether a device
supports DAX or not, the following order of operations should be
performed:
- If dax_dev pointer is NULL, it means the device driver explicitly
announce it doesn't support DAX. Then it is OK to directly return
false from __generic_fsdax_supported().
- If dax_dev pointer is NOT NULL, it might be because the driver doesn't
support DAX and not explicitly initialize related data structure. Then
bdev_dax_supported() should be called for further check.
If device driver desn't explicitly set its dax_dev pointer to NULL,
this is not a bug. Calling bdev_dax_supported() makes sure they can be
recognized as dax-unsupported eventually.
Fixes: c2affe920b0e ("dax: do not print error message for non-persistent memory block device")
Cc: Jan Kara <jack@suse.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-and-tested-by: Adrian Huang <ahuang12@lenovo.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Link: https://lore.kernel.org/r/20200903161625.19524-1-colyli@suse.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a compilation fix issue with ti-vpe on arm 32 bits
- two Kconfig fixes for imx214 and max9286 drivers
- a kernel information leak at v4l2-core on time32 compat ioctls
- some fixes at rc core unbind logic
- a fix at mceusb driver for it to not use GFP_ATOMIC
- fixes at cedrus and vicodec drivers at the control handling logic
- a fix at gpio-ir-tx to avoid disabling interruts on a spinlock
* tag 'media/v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: mceusb: Avoid GFP_ATOMIC where it is not needed
media: gpio-ir-tx: spinlock is not needed to disable interrupts
media: rc: do not access device via sysfs after rc_unregister_device()
media: rc: uevent sysfs file races with rc_unregister_device()
media: max9286: Depend on OF_GPIO
media: i2c: imx214: select V4L2_FWNODE
media: cedrus: Add missing v4l2_ctrl_request_hdl_put()
media: vicodec: add missing v4l2_ctrl_request_hdl_put()
media: media/v4l2-core: Fix kernel-infoleak in video_put_user()
media: ti-vpe: cal: Fix compilation on 32-bit ARM
|
|
Remove pointless ir_ prefix.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
rc-core kapi uses nanoseconds for infrared durations for receiving, and
microseconds for sending. The uapi already uses microseconds for both,
so this patch does not change the uapi.
Infrared durations do not need nanosecond resolution. IR protocols do not
have durations shorter than about 100 microseconds. Some IR hardware offers
250 microseconds resolution, which is sufficient for most protocols.
Better hardware has 50 microsecond resolution and is enough for every
protocol I am aware off.
Unify on microseconds everywhere. This simplifies the code since less
conversion between microseconds and nanoseconds needs to be done.
This affects:
- rx_resolution member of struct rc_dev
- timeout member of struct rc_dev
- duration member in struct ir_raw_event
Cc: "Bruno Prémont" <bonbons@linux-vserver.org>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Patrick Lerda <patrick9876@free.fr>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Benjamin Valentin <benpicco@googlemail.com>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
BaseRemoteCtl is not descriptive.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Both TT-connect S2-3600 and Pinnacle PCTV Sat HDTV are using
Intersil ISL6423 as LNB voltage regulator. This makes
TT-connect S2-3650 CI the only device which uses STM LNBP22 regulator
which is currently used for all devices driven by pctv452e driver.
This patch fixes this by creating an exception for TT-connect S2-3650 CI
to continue to use STM LNBP22 while all others now using correct ISL6423
driver which makes DiSEqC/EN50494 comands which involve voltage changes
now working on the other devices (which didn't work before).
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix the following versioncheck warning:
drivers/media/dvb-frontends/mxl5xx.c:30:1: unused including
<linux/version.h>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
kerneldoc
Fix W=1 compile warnings (invalid kerneldoc):
drivers/dma-buf/dma-fence-chain.c:233: warning: Function parameter or member 'seqno' not described in 'dma_fence_chain_init'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819175134.19261-2-krzk@kernel.org
|
|
Fix W=1 compile warnings (invalid kerneldoc):
drivers/dma-buf/dma-buf.c:328: warning: Function parameter or member 'dmabuf' not described in 'dma_buf_set_name'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819175134.19261-1-krzk@kernel.org
|
|
Don't need to declare those functions with extern:
drivers/staging/media/atomisp/pci/css_2401_system/host/isys_irq_private.h:51:35: warning: function 'isys_irqc_state_dump' with external linkage has definition
drivers/staging/media/atomisp/pci/css_2401_system/host/isys_irq_private.h:68:35: warning: function 'isys_irqc_reg_store' with external linkage has definition
drivers/staging/media/atomisp/pci/css_2401_system/host/isys_irq_private.h:85:39: warning: function 'isys_irqc_reg_load' with external linkage has definition
drivers/staging/media/atomisp/pci/css_2401_system/host/isys_irq.c:31:35: warning: function 'isys_irqc_status_enable' with external linkage has definition
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As smatch reports, there are several bad indents:
drivers/staging/media/atomisp/pci/hmm/hmm.c:271 hmm_alloc() warn: inconsistent indenting
drivers/staging/media/atomisp/pci/runtime/bufq/src/bufq.c:390 ia_css_bufq_enqueue_psys_event() warn: inconsistent indenting
drivers/staging/media/atomisp/pci/runtime/debug/src/ia_css_debug.c:2132 ia_css_debug_dump_isys_state() warn: inconsistent indenting
drivers/staging/media/atomisp/pci/runtime/binary/src/binary.c:246 sh_css_binary_get_sc_requirements() warn: inconsistent indenting
drivers/staging/media/atomisp/pci/runtime/binary/src/binary.c:565 ia_css_binary_get_shading_info_type_1() warn: inconsistent indenting
drivers/staging/media/atomisp/pci/sh_css.c:5109 sh_css_pipes_stop() warn: inconsistent indenting
drivers/staging/media/atomisp/pci/sh_css.c:8791 ia_css_pipe_create() warn: inconsistent indenting
Some of them are due to ifdefs. Get rid of them by either getting
a common code that would work for both ISP2400 and ISP2401 or
by creating separate functions, one for each ISP version.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Now that there's no duplication between ISP2400 and ISP2401
input system functions, we can include both at the system
global.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Reorder functions in order to declare before usage.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are some duplicated names between the ISP2401 and ISP2400
for the input system, with different meanings.
In order to avoid ubiquity, let's prepend those with the
name of the ISP.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There is a typedef for INPUT errors. This is different between
ISP2401 and ISP2400. Place both at the same struct, at the
global header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As there aren't duplicated names anymore, and the end goal
is to do runtime checks between ISP2400 and ISP2401,
remove the part of the Makefile which changes the include
places based on the compile-time version.
This shouldn't cause any effect, but it will make easier
for further patches meant to remove conditional compiler
decisions between ISP versions to be replaced by
runtime ones.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Just move the stuff there to the places where this header is
included.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There aren't much on this abstraction. Just move the defines
to isys_dma_private.h and isys_dma_public.h, cleaning up
the includes.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
