summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2022-04-22clk: microchip: mpfs: add RTCREF clock controlConor Dooley
The reference clock used by the PolarFire SoC's onboard rtc was missing from the clock driver. Add this clock at the "config" clock level, with the external reference clock as its parent. Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC") Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20220413075835.3354193-9-conor.dooley@microchip.com Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-04-22clk: microchip: mpfs: re-parent the configurable clocksConor Dooley
Currently the mpfs clock driver uses a reference clock called the "msspll", set in the device tree, as the parent for the cpu/axi/ahb (config) clocks. The frequency of the msspll is determined by the FPGA bitstream & the bootloader configures the clock to match the bitstream. The real reference is provided by a 100 or 125 MHz off chip oscillator. However, the msspll clock is not actually the parent of all clocks on the system - the reference clock for the rtc/mtimer actually has the off chip oscillator as its parent. In order to fix this, add support for reading the configuration of the msspll & reparent the "config" clocks so that they are derived from this clock rather than the reference in the device tree. Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC") Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20220413075835.3354193-8-conor.dooley@microchip.com Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-04-22clk: microchip: mpfs: mark CLK_ATHENA as criticalConor Dooley
CLK_ATHENA is another fabric interconnect and should be marked as critical as with FIC0-3, since disabling it will cause part of the fabric to go into reset. Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC") Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20220413075835.3354193-3-conor.dooley@microchip.com Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-04-22clk: microchip: mpfs: fix parents for FIC clocksConor Dooley
The fabric interconnects are on the AXI bus not AHB. Update their parent clocks to fix this. Fixes: 635e5e73370e ("clk: microchip: Add driver for Microchip PolarFire SoC") Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com> Signed-off-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20220413075835.3354193-2-conor.dooley@microchip.com Acked-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Stephen Boyd <sboyd@kernel.org>
2022-04-22Merge tag 'ata-5.18-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata Pull ATA fix from Damien Le Moal: "A single fix to avoid a NULL pointer dereference in the pata_marvell driver with adapters not supporting DMA, from Zheyu" * tag 'ata-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata: ata: pata_marvell: Check the 'bmdma_addr' beforing reading
2022-04-22net: ethernet: stmmac: fix write to sgmii_adapter_baseDinh Nguyen
I made a mistake with the commit a6aaa0032424 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link"). I should have tested against both scenario of having a SGMII interface and one without. Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is NULL, thus a write to this address will fail. Cc: stable@vger.kernel.org Fixes: a6aaa0032424 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link") Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-22wireguard: device: check for metadata_dst with skb_valid_dst()Nikolay Aleksandrov
When we try to transmit an skb with md_dst attached through wireguard we hit a null pointer dereference in wg_xmit() due to the use of dst_mtu() which calls into dst_blackhole_mtu() which in turn tries to dereference dst->dev. Since wireguard doesn't use md_dsts we should use skb_valid_dst(), which checks for DST_METADATA flag, and if it's set, then falls back to wireguard's device mtu. That gives us the best chance of transmitting the packet; otherwise if the blackhole netdev is used we'd get ETH_MIN_MTU. [ 263.693506] BUG: kernel NULL pointer dereference, address: 00000000000000e0 [ 263.693908] #PF: supervisor read access in kernel mode [ 263.694174] #PF: error_code(0x0000) - not-present page [ 263.694424] PGD 0 P4D 0 [ 263.694653] Oops: 0000 [#1] PREEMPT SMP NOPTI [ 263.694876] CPU: 5 PID: 951 Comm: mausezahn Kdump: loaded Not tainted 5.18.0-rc1+ #522 [ 263.695190] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1.fc35 04/01/2014 [ 263.695529] RIP: 0010:dst_blackhole_mtu+0x17/0x20 [ 263.695770] Code: 00 00 00 0f 1f 44 00 00 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 8b 47 10 48 83 e0 fc 8b 40 04 85 c0 75 09 48 8b 07 <8b> 80 e0 00 00 00 c3 66 90 0f 1f 44 00 00 48 89 d7 be 01 00 00 00 [ 263.696339] RSP: 0018:ffffa4a4422fbb28 EFLAGS: 00010246 [ 263.696600] RAX: 0000000000000000 RBX: ffff8ac9c3553000 RCX: 0000000000000000 [ 263.696891] RDX: 0000000000000401 RSI: 00000000fffffe01 RDI: ffffc4a43fb48900 [ 263.697178] RBP: ffffa4a4422fbb90 R08: ffffffff9622635e R09: 0000000000000002 [ 263.697469] R10: ffffffff9b69a6c0 R11: ffffa4a4422fbd0c R12: ffff8ac9d18b1a00 [ 263.697766] R13: ffff8ac9d0ce1840 R14: ffff8ac9d18b1a00 R15: ffff8ac9c3553000 [ 263.698054] FS: 00007f3704c337c0(0000) GS:ffff8acaebf40000(0000) knlGS:0000000000000000 [ 263.698470] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 263.698826] CR2: 00000000000000e0 CR3: 0000000117a5c000 CR4: 00000000000006e0 [ 263.699214] Call Trace: [ 263.699505] <TASK> [ 263.699759] wg_xmit+0x411/0x450 [ 263.700059] ? bpf_skb_set_tunnel_key+0x46/0x2d0 [ 263.700382] ? dev_queue_xmit_nit+0x31/0x2b0 [ 263.700719] dev_hard_start_xmit+0xd9/0x220 [ 263.701047] __dev_queue_xmit+0x8b9/0xd30 [ 263.701344] __bpf_redirect+0x1a4/0x380 [ 263.701664] __dev_queue_xmit+0x83b/0xd30 [ 263.701961] ? packet_parse_headers+0xb4/0xf0 [ 263.702275] packet_sendmsg+0x9a8/0x16a0 [ 263.702596] ? _raw_spin_unlock_irqrestore+0x23/0x40 [ 263.702933] sock_sendmsg+0x5e/0x60 [ 263.703239] __sys_sendto+0xf0/0x160 [ 263.703549] __x64_sys_sendto+0x20/0x30 [ 263.703853] do_syscall_64+0x3b/0x90 [ 263.704162] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 263.704494] RIP: 0033:0x7f3704d50506 [ 263.704789] Code: 48 c7 c0 ff ff ff ff eb b7 66 2e 0f 1f 84 00 00 00 00 00 90 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 11 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 72 c3 90 55 48 83 ec 30 44 89 4c 24 2c 4c 89 [ 263.705652] RSP: 002b:00007ffe954b0b88 EFLAGS: 00000246 ORIG_RAX: 000000000000002c [ 263.706141] RAX: ffffffffffffffda RBX: 0000558bb259b490 RCX: 00007f3704d50506 [ 263.706544] RDX: 000000000000004a RSI: 0000558bb259b7b2 RDI: 0000000000000003 [ 263.706952] RBP: 0000000000000000 R08: 00007ffe954b0b90 R09: 0000000000000014 [ 263.707339] R10: 0000000000000000 R11: 0000000000000246 R12: 00007ffe954b0b90 [ 263.707735] R13: 000000000000004a R14: 0000558bb259b7b2 R15: 0000000000000001 [ 263.708132] </TASK> [ 263.708398] Modules linked in: bridge netconsole bonding [last unloaded: bridge] [ 263.708942] CR2: 00000000000000e0 Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Link: https://github.com/cilium/cilium/issues/19428 Reported-by: Martynas Pumputis <m@lambda.lt> Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-22net: dsa: realtek: remove realtek,rtl8367s stringLuiz Angelo Daros de Luca
There is no need to add new compatible strings for each new supported chip version. The compatible string is used only to select the subdriver (rtl8365mb.c or rtl8366rb.c). Once in the subdriver, it will detect the chip model by itself, ignoring which compatible string was used. Link: https://lore.kernel.org/netdev/20220414014055.m4wbmr7tdz6hsa3m@bang-olufsen.dk/ Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Link: https://lore.kernel.org/r/20220418233558.13541-2-luizluca@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-23pinctrl: stm32: Keep pinctrl block clock enabled when LEVEL IRQ requestedMarek Vasut
The current EOI handler for LEVEL triggered interrupts calls clk_enable(), register IO, clk_disable(). The clock manipulation requires locking which happens with IRQs disabled in clk_enable_lock(). Instead of turning the clock on and off all the time, enable the clock in case LEVEL interrupt is requested and keep the clock enabled until all LEVEL interrupts are freed. The LEVEL interrupts are an exception on this platform and seldom used, so this does not affect the common case. This simplifies the LEVEL interrupt handling considerably and also fixes the following splat found when using preempt-rt: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at kernel/locking/rtmutex.c:2040 __rt_mutex_trylock+0x37/0x62 Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.10.109-rt65-stable-standard-00068-g6a5afc4b1217 #85 Hardware name: STM32 (Device Tree Support) [<c010a45d>] (unwind_backtrace) from [<c010766f>] (show_stack+0xb/0xc) [<c010766f>] (show_stack) from [<c06353ab>] (dump_stack+0x6f/0x84) [<c06353ab>] (dump_stack) from [<c01145e3>] (__warn+0x7f/0xa4) [<c01145e3>] (__warn) from [<c063386f>] (warn_slowpath_fmt+0x3b/0x74) [<c063386f>] (warn_slowpath_fmt) from [<c063b43d>] (__rt_mutex_trylock+0x37/0x62) [<c063b43d>] (__rt_mutex_trylock) from [<c063c053>] (rt_spin_trylock+0x7/0x16) [<c063c053>] (rt_spin_trylock) from [<c036a2f3>] (clk_enable_lock+0xb/0x80) [<c036a2f3>] (clk_enable_lock) from [<c036ba69>] (clk_core_enable_lock+0x9/0x18) [<c036ba69>] (clk_core_enable_lock) from [<c034e9f3>] (stm32_gpio_get+0x11/0x24) [<c034e9f3>] (stm32_gpio_get) from [<c034ef43>] (stm32_gpio_irq_trigger+0x1f/0x48) [<c034ef43>] (stm32_gpio_irq_trigger) from [<c014aa53>] (handle_fasteoi_irq+0x71/0xa8) [<c014aa53>] (handle_fasteoi_irq) from [<c0147111>] (generic_handle_irq+0x19/0x22) [<c0147111>] (generic_handle_irq) from [<c014752d>] (__handle_domain_irq+0x55/0x64) [<c014752d>] (__handle_domain_irq) from [<c0346f13>] (gic_handle_irq+0x53/0x64) [<c0346f13>] (gic_handle_irq) from [<c0100ba5>] (__irq_svc+0x65/0xc0) Exception stack(0xc0e01f18 to 0xc0e01f60) 1f00: 0000300c 00000000 1f20: 0000300c c010ff01 00000000 00000000 c0e00000 c0e07714 00000001 c0e01f78 1f40: c0e07758 00000000 ef7cd0ff c0e01f68 c010554b c0105542 40000033 ffffffff [<c0100ba5>] (__irq_svc) from [<c0105542>] (arch_cpu_idle+0xc/0x1e) [<c0105542>] (arch_cpu_idle) from [<c063be95>] (default_idle_call+0x21/0x3c) [<c063be95>] (default_idle_call) from [<c01324f7>] (do_idle+0xe3/0x1e4) [<c01324f7>] (do_idle) from [<c01327b3>] (cpu_startup_entry+0x13/0x14) [<c01327b3>] (cpu_startup_entry) from [<c0a00c13>] (start_kernel+0x397/0x3d4) [<c0a00c13>] (start_kernel) from [<00000000>] (0x0) ---[ end trace 0000000000000002 ]--- Power consumption measured on STM32MP157C DHCOM SoM is not increased or is below noise threshold. Fixes: 47beed513a85b ("pinctrl: stm32: Add level interrupt support to gpio irq chip") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Alexandre Torgue <alexandre.torgue@foss.st.com> Cc: Fabien Dessenne <fabien.dessenne@foss.st.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Marc Zyngier <maz@kernel.org> Cc: linux-stm32@st-md-mailman.stormreply.com Cc: linux-arm-kernel@lists.infradead.org To: linux-gpio@vger.kernel.org Reviewed-by: Fabien Dessenne <fabien.dessenne@foss.st.com> Link: https://lore.kernel.org/r/20220421140827.214088-1-marex@denx.de Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-04-22pinctrl: rockchip: sort the rk3308_mux_recalced_data entriesLuca Ceresoli
All the entries are sorted according to num/pin except for two entries. Sort them too. Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20220420142432.248565-2-luca.ceresoli@bootlin.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-04-22pinctrl: rockchip: fix RK3308 pinmux bitsLuca Ceresoli
Some of the pinmuxing bits described in rk3308_mux_recalced_data are wrong, pointing to non-existing registers. Fix the entire table. Also add a comment in front of each entry with the same string that appears in the datasheet to make the table easier to compare with the docs. This fix has been tested on real hardware for the gpio3b3_sel entry. Fixes: 7825aeb7b208 ("pinctrl: rockchip: add rk3308 SoC support") Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Link: https://lore.kernel.org/r/20220420142432.248565-1-luca.ceresoli@bootlin.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-04-22Merge tag 'samsung-pinctrl-fixes-5.18' of ↵Linus Walleij
https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into fixes Samsung pinctrl drivers fixes for v5.18 1. Fix sparse warning introduced in v5.18-rc1. 2. Fix possible unmet Kconfig dependency with COMPILE_TEST, present since v4.3 or earlier.
2022-04-22gpio: Request interrupts after IRQ is initializedMario Limonciello
Commit 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members before initialization") attempted to fix a race condition that lead to a NULL pointer, but in the process caused a regression for _AEI/_EVT declared GPIOs. This manifests in messages showing deferred probing while trying to allocate IRQs like so: amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x0000 to IRQ, err -517 amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x002C to IRQ, err -517 amd_gpio AMDI0030:00: Failed to translate GPIO pin 0x003D to IRQ, err -517 [ .. more of the same .. ] The code for walking _AEI doesn't handle deferred probing and so this leads to non-functional GPIO interrupts. Fix this issue by moving the call to `acpi_gpiochip_request_interrupts` to occur after gc->irc.initialized is set. Fixes: 5467801f1fcb ("gpio: Restrict usage of GPIO chip irq members before initialization") Link: https://lore.kernel.org/linux-gpio/BL1PR12MB51577A77F000A008AA694675E2EF9@BL1PR12MB5157.namprd12.prod.outlook.com/ Link: https://bugzilla.suse.com/show_bug.cgi?id=1198697 Link: https://bugzilla.kernel.org/show_bug.cgi?id=215850 Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1979 Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1976 Reported-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Shreeya Patel <shreeya.patel@collabora.com> Tested-By: Samuel Čavoj <samuel@cavoj.net> Tested-By: lukeluk498@gmail.com Link: Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-and-tested-by: Takashi Iwai <tiwai@suse.de> Cc: Shreeya Patel <shreeya.patel@collabora.com> Cc: stable@vger.kernel.org Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2022-04-22Merge tag 'riscv-for-linus-5.18-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux Pull RISC-V fixes Palmer Dabbelt: - A pair of build fixes for the recent cpuidle driver - A fix for systems without sv57 that manifests as a crash early in boot * tag 'riscv-for-linus-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: RISC-V: cpuidle: fix Kconfig select for RISCV_SBI_CPUIDLE RISC-V: mm: Fix set_satp_mode() for platform not having Sv57 cpuidle: riscv: support non-SMP config
2022-04-22Merge tag 'arm64-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux Pull arm64 fixes from Will Deacon: "There's no real pattern to the fixes, but the main one fixes our pmd_leaf() definition to resolve a NULL dereference on the migration path. - Fix PMU event validation in the absence of any event counters - Fix allmodconfig build using clang in conjunction with binutils - Fix definitions of pXd_leaf() to handle PROT_NONE entries - More typo fixes" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: arm64: mm: fix p?d_leaf() arm64: fix typos in comments arm64: Improve HAVE_DYNAMIC_FTRACE_WITH_REGS selection for clang arm_pmu: Validate single/group leader events
2022-04-22Merge tag 'sound-5.18-rc4' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound Pull sound fixes from Takashi Iwai: "At this time, the majority of changes are for pending ASoC fixes while a few usual HD-audio and USB-audio quirks are found. Almost all patches are small device-specific fixes, and nothing worrisome stands out, so far" * tag 'sound-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (37 commits) ALSA: hda/realtek: Add quirk for Clevo NP70PNP ALSA: hda: intel-dsp-config: Add RaptorLake PCI IDs ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on EliteBook 845/865 G9 ALSA: usb-audio: Clear MIDI port active flag after draining ALSA: usb-audio: add mapping for MSI MAG X570S Torpedo MAX. ALSA: hda/i915: Fix one too many pci_dev_put() ALSA: hda/hdmi: add HDMI codec VID for Raptorlake-P ALSA: hda/hdmi: fix warning about PCM count when used with SOF sound/oss/dmasound: fix 'dmasound_setup' defined but not used firmware: cs_dsp: Fix overrun of unterminated control name string ASoC: codecs: Fix an error handling path in (rx|tx|va)_macro_probe() ASoC: Intel: sof_es8336: Add a quirk for Huawei Matebook D15 ASoC: Intel: sof_es8336: add a quirk for headset at mic1 port ASoC: Intel: sof_es8336: support a separate gpio to control headphone ASoC: Intel: sof_es8336: simplify speaker gpio naming ASoC: wm8731: Disable the regulator when probing fails ASoC: Intel: soc-acpi: correct device endpoints for max98373 ASoC: codecs: wcd934x: do not switch off SIDO Buck when codec is in use ASoC: SOF: topology: Fix memory leak in sof_control_load() ASoC: SOF: topology: cleanup dailinks on widget unload ...
2022-04-22binder: Gracefully handle BINDER_TYPE_FDA objects with num_fds=0Alessandro Astone
Some android userspace is sending BINDER_TYPE_FDA objects with num_fds=0. Like the previous patch, this is reproducible when playing a video. Before commit 09184ae9b575 BINDER_TYPE_FDA objects with num_fds=0 were 'correctly handled', as in no fixup was performed. After commit 09184ae9b575 we aggregate fixup and skip regions in binder_ptr_fixup structs and distinguish between the two by using the skip_size field: if it's 0, then it's a fixup, otherwise skip. When processing BINDER_TYPE_FDA objects with num_fds=0 we add a skip region of skip_size=0, and this causes issues because now binder_do_deferred_txn_copies will think this was a fixup region. To address that, return early from binder_translate_fd_array to avoid adding an empty skip region. Fixes: 09184ae9b575 ("binder: defer copies of pre-patched txn data") Acked-by: Todd Kjos <tkjos@google.com> Cc: stable <stable@kernel.org> Signed-off-by: Alessandro Astone <ales.astone@gmail.com> Link: https://lore.kernel.org/r/20220415120015.52684-1-ales.astone@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22binder: Address corner cases in deferred copy and fixupAlessandro Astone
When handling BINDER_TYPE_FDA object we are pushing a parent fixup with a certain skip_size but no scatter-gather copy object, since the copy is handled standalone. If BINDER_TYPE_FDA is the last children the scatter-gather copy loop will never stop to skip it, thus we are left with an item in the parent fixup list. This will trigger the BUG_ON(). This is reproducible in android when playing a video. We receive a transaction that looks like this: obj[0] BINDER_TYPE_PTR, parent obj[1] BINDER_TYPE_PTR, child obj[2] BINDER_TYPE_PTR, child obj[3] BINDER_TYPE_FDA, child Fixes: 09184ae9b575 ("binder: defer copies of pre-patched txn data") Acked-by: Todd Kjos <tkjos@google.com> Cc: stable <stable@kernel.org> Signed-off-by: Alessandro Astone <ales.astone@gmail.com> Link: https://lore.kernel.org/r/20220415120015.52684-2-ales.astone@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22thermal/governor: Remove deprecated informationDaniel Lezcano
The userspace governor is still in use on production systems and the deprecating warning is scary. Even if we want to get rid of the userspace governor, it is too soon yet as the alternatives are not yet adopted. Change the deprecated warning by an information message suggesting to switch to the netlink thermal events. Fixes: 0275c9fb0eff ("thermal/core: Make the userspace governor deprecated") Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2022-04-22Revert "thermal/core: Deprecate changing cooling device state from userspace"Daniel Lezcano
This reverts commit a67a46af4ad6342378e332b7420c1d1a2818c53f. It has been reported the warning is annoying as the cooling device state is still needed on some production system. Meanwhile we provide a way to consolidate the thermal framework to prevent multiple actors acting on the cooling devices with conflicting decisions, let's revert this warning. Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2022-04-22serial: 8250: Correct the clock for EndRun PTP/1588 PCIe deviceMaciej W. Rozycki
The EndRun PTP/1588 dual serial port device is based on the Oxford Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock. The clock rate is divided by the oversampling rate of 16 as it is supplied to the baud rate generator, yielding the baud base of 3906250. Replace the incorrect baud base of 4000000 with the right value of 3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct the clock for OxSemi PCIe devices"). Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable <stable@kernel.org> Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: 8250: Also set sticky MCR bits in console restorationMaciej W. Rozycki
Sticky MCR bits are lost in console restoration if console suspending has been disabled. This currently affects the AFE bit, which works in combination with RTS which we set, so we want to make sure the UART retains control of its FIFO where previously requested. Also specific drivers may need other bits in the future. Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend") Cc: stable@vger.kernel.org # v4.0+ Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty: n_gsm: fix software flow control handlingDaniel Starke
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.4.8.1 states that XON/XOFF characters shall be used instead of Fcon/Fcoff command in advanced option mode to handle flow control. Chapter 5.4.8.2 describes how XON/XOFF characters shall be handled. Basic option mode only used Fcon/Fcoff commands and no XON/XOFF characters. These are treated as data bytes here. The current implementation uses the gsm_mux field 'constipated' to handle flow control from the remote peer and the gsm_dlci field 'constipated' to handle flow control from each DLCI. The later is unrelated to this patch. The gsm_mux field is correctly set for Fcon/Fcoff commands in gsm_control_message(). However, the same is not true for XON/XOFF characters in gsm1_receive(). Disable software flow control handling in the tty to allow explicit handling by n_gsm. Add the missing handling in advanced option mode for gsm_mux in gsm1_receive() to comply with the standard. This patch depends on the following commit: Commit 8838b2af23ca ("tty: n_gsm: fix SW flow control encoding/handling") Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220422071025.5490-3-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty: n_gsm: fix invalid use of MSC in advanced optionDaniel Starke
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010. See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516 The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to the newer 27.010 here. Chapter 5.4.6.3.7 states that the Modem Status Command (MSC) shall only be used if the basic option was chosen. The current implementation uses MSC frames even if advanced option was chosen to inform the peer about modem line state updates. A standard conform peer may choose to discard these frames in advanced option mode. Furthermore, gsmtty_modem_update() is not part of the 'tty_operations' functions despite its name. Rename gsmtty_modem_update() to gsm_modem_update() to clarify this. Split its function into gsm_modem_upd_via_data() and gsm_modem_upd_via_msc() depending on the encoding and adaption. Introduce gsm_dlci_modem_output() as adaption of gsm_dlci_data_output() to encode and queue empty frames in advanced option mode. Use it in gsm_modem_upd_via_data(). gsm_modem_upd_via_msc() is based on the initial gsmtty_modem_update() function which used only MSC frames to update modem states. Fixes: e1eaea46bb40 ("tty: n_gsm line discipline") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220422071025.5490-2-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty: n_gsm: fix broken virtual tty handlingDaniel Starke
Dynamic virtual tty registration was introduced to allow the user to handle these cases with uevent rules. The following commits relate to this: Commit 5b87686e3203 ("tty: n_gsm: Modify gsmtty driver register method when config requester") Commit 0b91b5332368 ("tty: n_gsm: Save dlci address open status when config requester") Commit 46292622ad73 ("tty: n_gsm: clean up indenting in gsm_queue()") However, the following behavior can be seen with this implementation: - n_gsm ldisc is activated via ioctl - all configuration parameters are set to their default value (initiator=0) - the mux gets activated and attached and gsmtty0 is being registered in in gsm_dlci_open() after DLCI 0 was established (DLCI 0 is the control channel) - the user configures n_gsm via ioctl GSMIOC_SETCONF as initiator - this re-attaches the n_gsm mux - no new gsmtty devices are registered in gsmld_attach_gsm() because the mux is already active - the initiator side registered only the control channel as gsmtty0 (which should never happen) and no user channel tty The commits above make it impossible to operate the initiator side as no user channel tty is or will be available. On the other hand, this behavior will make it also impossible to allow DLCI parameter negotiation on responder side in the future. The responder side first needs to provide a device for the application before the application can set its parameters of the associated DLCI via ioctl. Note that the user application is still able to detect a link establishment without relaying to uevent by waiting for DTR open on responder side. This is the same behavior as on a physical serial interface. And on initiator side a tty hangup can be detected if a link establishment request failed. Revert the commits above completely to always register all user channels and no control channel after mux attachment. No other changes are made. Fixes: 5b87686e3203 ("tty: n_gsm: Modify gsmtty driver register method when config requester") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220422071025.5490-1-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22Revert "serial: sc16is7xx: Clear RS485 bits in the shutdown"Hui Wang
This reverts commit 927728a34f11b5a27f4610bdb7068317d6fdc72a. Once the uart_port->rs485->flag is set to SER_RS485_ENABLED, the port should always work in RS485 mode. If users want the port to leave RS485 mode, they need to call ioctl() to clear SER_RS485_ENABLED. So here we shouldn't clear the RS485 bits in the shutdown(). Fixes: 927728a34f11 ("serial: sc16is7xx: Clear RS485 bits in the shutdown") Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20220418094339.678144-1-hui.wang@canonical.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: stm32: add earlycon supportValentin Caron
Add early console support in stm32 uart driver. Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com> Signed-off-by: Valentin Caron <valentin.caron@foss.st.com> Link: https://lore.kernel.org/r/20220419085330.1178925-4-valentin.caron@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: stm32: add KGDB supportValentin Caron
Add support for KGDB in stm32 serial driver by implementing characters polling callbacks (poll_init, poll_get_char and poll_put_char). Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com> Signed-off-by: Jean Philippe Romain <jean-philippe.romain@foss.st.com> Signed-off-by: Valentin Caron <valentin.caron@foss.st.com> Link: https://lore.kernel.org/r/20220419085330.1178925-3-valentin.caron@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: stm32: remove infinite loop possibility in putchar functionValentin Caron
Rework stm32_usart_console_putchar() function in order to anticipate the case where the character can never be sent. Signed-off-by: Valentin Caron <valentin.caron@foss.st.com> Link: https://lore.kernel.org/r/20220419085330.1178925-2-valentin.caron@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty: Add function for handling flow control charsIlpo Järvinen
Move receive path flow control character handling to own function. No functional changes. Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20220411094859.10894-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: core: fix tcdrain() with CTS enabledTomasz Moń
Do not set timeout to twice the approximate amount of time to send the entire FIFO if CTS is enabled. If the caller requested no timeout, e.g. when userspace program called tcdrain(), then wait without any timeout. Premature return from tcdrain() was observed on imx based system which has 32 character long transmitter FIFO with hardware CTS handling. Simple userspace application that reproduces problem has to: * Open tty device, enable hardware flow control (CRTSCTS) * Write data, e.g. 26 bytes * Call tcdrain() to wait for the transmitter * Close tty device The other side of serial connection has to: * Receive some data, e.g. 10 bytes * Set RTS output (CTS input from sender perspective) inactive for at least twice the port timeout * Try to receive remaining data Without this patch, userspace application will finish without any error while the other side of connection will never receive remaining data. Signed-off-by: Tomasz Moń <tomasz.mon@camlingroup.com> Link: https://lore.kernel.org/r/20220228054911.1420221-1-tomasz.mon@camlingroup.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22char: ttyprintk: register consoleVincent Whitchurch
Register a console in the ttyprintk driver so that it can be selected for /dev/console with console=ttyprintk on the kernel command line, similar to other console drivers. Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20220215141750.92808-1-vincent.whitchurch@axis.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial/8250: Use fifo in 8250 console driverWander Lairson Costa
Note: I am using a small test app + driver located at [0] for the problem description. serco is a driver whose write function dispatches to the serial controller. sertest is a user-mode app that writes n bytes to the serial console using the serco driver. While investigating a bug in the RHEL kernel, I noticed that the serial console throughput is way below the configured speed of 115200 bps in a HP Proliant DL380 Gen9. I was expecting something above 10KB/s, but I got 2.5KB/s. $ time ./sertest -n 2500 /tmp/serco real 0m0.997s user 0m0.000s sys 0m0.997s With the help of the function tracer, I then noticed the serial controller was taking around 410us seconds to dispatch one single byte: $ trace-cmd record -p function_graph -g serial8250_console_write \ ./sertest -n 1 /tmp/serco $ trace-cmd report | serial8250_console_write() { 0.384 us | _raw_spin_lock_irqsave(); 1.836 us | io_serial_in(); 1.667 us | io_serial_out(); | uart_console_write() { | serial8250_console_putchar() { | wait_for_xmitr() { 1.870 us | io_serial_in(); 2.238 us | } 1.737 us | io_serial_out(); 4.318 us | } 4.675 us | } | wait_for_xmitr() { 1.635 us | io_serial_in(); | __const_udelay() { 1.125 us | delay_tsc(); 1.429 us | } ... ... ... 1.683 us | io_serial_in(); | __const_udelay() { 1.248 us | delay_tsc(); 1.486 us | } 1.671 us | io_serial_in(); 411.342 us | } In another machine, I measured a throughput of 11.5KB/s, with the serial controller taking between 80-90us to send each byte. That matches the expected throughput for a configuration of 115200 bps. This patch changes the serial8250_console_write to use the 16550 fifo if available. In my benchmarks I got around 25% improvement in the slow machine, and no performance penalty in the fast machine. Signed-off-by: Wander Lairson Costa <wander@redhat.com> Link: https://lore.kernel.org/r/20220411174841.34936-2-wander@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22drivers: tty: serial: Fix deadlock in sa1100_set_termios()Duoming Zhou
There is a deadlock in sa1100_set_termios(), which is shown below: (Thread 1) | (Thread 2) | sa1100_enable_ms() sa1100_set_termios() | mod_timer() spin_lock_irqsave() //(1) | (wait a time) ... | sa1100_timeout() del_timer_sync() | spin_lock_irqsave() //(2) (wait timer to stop) | ... We hold sport->port.lock in position (1) of thread 1 and use del_timer_sync() to wait timer to stop, but timer handler also need sport->port.lock in position (2) of thread 2. As a result, sa1100_set_termios() will block forever. This patch moves del_timer_sync() before spin_lock_irqsave() in order to prevent the deadlock. Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/20220417111626.7802-1-duoming@zju.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty/sysrq: change the definition of sysrq_key_table's element to make it ↵Junwen Wu
more readable The definition of sysrq_key_table's elements, like sysrq_thaw_op and sysrq_showallcpus_op are not consistent with sysrq_ftrace_dump_op, Consistency makes code more readable. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Junwen Wu <wudaemon@gmail.com> Link: https://lore.kernel.org/r/20220418153703.97705-1-wudaemon@163.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty: serial: fsl_lpuart: remove the count initialization as it is not neededSherry Sun
No need to initialize the count variable in lpuart_copy_rx_to_tty(), so let's remove it here. Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20220418021844.29591-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: allow COMPILE_TEST for some driversJiri Slaby
Some more serial drivers can be compile-tested under certain circumstances (when building a specific architecture). So allow for that. This reduces the need of zillion mach/subarch-specific configs. And since the 0day bot has only allmodconfig's for some archs, this increases build coverage there too. Note that cpm needs a minor update in the header, so that it drags in at least some defines (CPM2 ones). Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421101708.5640-8-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: pic32: make SERIAL_PIC32_CONSOLE depend on SERIAL_PIC32=yJiri Slaby
pic32_uart contains this: #ifdef CONFIG_SERIAL_PIC32_CONSOLE ... console_initcall(pic32_console_init); ... core_initcall(pic32_late_console_init); ... #endif ... arch_initcall(pic32_uart_init); When the driver is built as module, all three above become module_init(). So if SERIAL_PIC32_CONSOLE is set while SERIAL_PIC32=m, it results in the following build error: In file included from include/linux/device/driver.h:21, from include/linux/device.h:32, from include/linux/platform_device.h:13, from drivers/tty/serial/pic32_uart.c:12: include/linux/module.h:131:49: error: redefinition of '__inittest' So make sure SERIAL_PIC32_CONSOLE can be set only when SERIAL_PIC32=y -- similar as for other drivers. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421101708.5640-7-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: qcom: use check for empty instead of pendingJiri Slaby
The code wants to know if the circ buffer is empty, so use the proper macro. No functional change intended, just saner function name used for that use case. Cc: Andy Gross <agross@kernel.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421101708.5640-6-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: zs: use NULL as a pointer, not 0Jiri Slaby
struct uart_port::membase is declared as a pointer. So it should be initialized by NULL, not zero constant. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421101708.5640-5-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: xilinx_uartps: cache xmit in cdns_uart_handle_tx()Jiri Slaby
Cache port->state->xmit into a local variable (xmit) in cdns_uart_handle_tx(). This reduces length of some lines there significantly. I.e. makes the code more readable. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421101708.5640-4-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: xilinx_uartps: return early in cdns_uart_handle_tx()Jiri Slaby
Return from the true branch of the 'if'. This saves one indentation level and makes the code more readable. The two comments about what obvious code does are removed too. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421101708.5640-3-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: sunplus-uart: change sunplus_console_ports from global to staticTom Rix
Smatch reports this issue sunplus-uart.c:501:26: warning: symbol 'sunplus_console_ports' was not declared. Should it be static? sunplus_console_ports is only used in sunplus-uart.c so change its storage-class specifier to static Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/20220421152505.1531507-1-trix@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty: serial: meson: Added S4 SOC compatibilityYu Tu
Make UART driver compatible with S4 SOC UART. Meanwhile, the S4 SOC UART uses 12MHz as the clock source for baud rate calculations. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Yu Tu <yu.tu@amlogic.com> Link: https://lore.kernel.org/r/20220422111320.19234-3-yu.tu@amlogic.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22tty: serial: meson: Add a 12MHz internal clock rate to calculate baud rate ↵Yu Tu
in order to meet the baud rate requirements of special BT modules A /2 divider over XTAL was introduced since G12A, and is preferred to be used over the still present /3 divider since it provides much closer frequencies vs the request baudrate. Especially the BT module uses 3Mhz baud rate. 8Mhz calculations can lead to baud rate bias, causing some problems. Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Yu Tu <yu.tu@amlogic.com> Link: https://lore.kernel.org/r/20220422111320.19234-2-yu.tu@amlogic.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: icom: remove unused struct icom_port membersJiri Slaby
Some members of struct icom_port are completely unused or only set and never read. Remove all those. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421085808.24152-11-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: icom: delete empty serial hooksJiri Slaby
uart_ops::release_port() and uart_ops::request_port() are not required by the serial layer. So no need to define empty ones. Remove them. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421085808.24152-10-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: icom: use list_for_each_entry()Jiri Slaby
Use list_for_each_entry() helper instead of explicit combo of list_for_each() and list_entry(). Note that pos is used as a reference point in list_add_tail() in icom_alloc_adapter(). This functionality remains as with an empty list, cur_adapter_entry->icom_adapter_entry is still the list head. This simplifies the code a bit. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421085808.24152-9-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: icom: make icom_acfg_baud const and unsignedJiri Slaby
The baud rates are unsigned constants. So mark them as such. Not only it makes sense, but they are passed also to uart_get_baud_rate() and that expects unsigned int as baud rates on input. Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421085808.24152-8-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22serial: icom: use ARRAY_SIZEJiri Slaby
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Link: https://lore.kernel.org/r/20220421085808.24152-7-jslaby@suse.cz Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit (git 2.34.1) at 2025-09-21 01:06:45 +0000