| Age | Commit message (Collapse) | Author |
|---|
|
The current logic around the 'use_dac' module parameter prevents the
r81969 driver from being loadable on 64-bit systems without any RAM
below 4 GB when the parameter is left at its default value.
So introduce a new default value -1 which indicates that 64-bit DMA
should be enabled on sufficiently recent PCIe chips, i.e., versions
RTL_GIGA_MAC_VER_18 or later. Explicit param values of 0 or 1 retain
the existing behavior of unconditionally enabling/disabling 64-bit DMA
on 64-bit architectures (i.e., regardless of the type and version of the
chip)
Since PCIe chips do not need to CPlusCmd Dual Address Cycle to be set,
make that conditional on the device type as well.
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you compile without OF_MDIO support in an RGMII configuration, we fail
to configure the dp83867 phy today by writing garbage into its configuration
registers.
On the other hand if you do compile with OF_MDIO and the phy gets loaded via
device tree, you have to have the properties set in the device tree, otherwise
we fail to load the driver and don't even attach the generic phy driver to
the interface anymore.
To make things slightly more consistent, make the rgmii configuration properties
optional and allow a user to omit them in their device tree.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_OF_MDIO is configured as module, the #define for it really
is CONFIG_OF_MDIO_MODULE, not CONFIG_OF_MDIO. So if we are compiling it
as module, the dp83867 doesn't see that OF_MDIO was selected and doesn't
read the dt rgmii parameters.
The fix is simple: Use IS_ENABLED(). It checks for both - module as well
as compiled in code.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge tag 'qcom-soc-for-4.7-2' into net-next
This merges the Qualcomm SOC tree with the net-next, solving the
merge conflict in the SMD API between the two.
|
|
In testing with HiKey, we found that since
commit 3f30b158eba5 ("asix: On RX avoid creating bad Ethernet
frames"),
we're seeing lots of noise during network transfers:
[ 239.027993] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.037310] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x54ebb5ec, offset 4
[ 239.045519] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xcdffe7a2, offset 4
[ 239.275044] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.284355] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x1d36f59d, offset 4
[ 239.292541] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0xaef3c1e9, offset 4
[ 239.518996] asix 1-1.1:1.0 eth0: asix_rx_fixup() Data Header synchronisation was lost, remaining 988
[ 239.528300] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x2881912, offset 4
[ 239.536413] asix 1-1.1:1.0 eth0: asix_rx_fixup() Bad Header Length 0x5638f7e2, offset 4
And network throughput ends up being pretty bursty and slow with
a overall throughput of at best ~30kB/s (where as previously we
got 1.1MB/s with the slower USB1.1 "full speed" host).
We found the issue also was reproducible on a x86_64 system,
using a "high-speed" USB2.0 port but the throughput did not
measurably drop (possibly due to the scp transfer being cpu
bound on my slow test hardware).
After lots of debugging, I found the check added in the
problematic commit seems to be calculating the offset
incorrectly.
In the normal case, in the main loop of the function, we do:
(where offset is zero, or set to "offset += (copy_length + 1) &
0xfffe" in the previous loop)
rx->header = get_unaligned_le32(skb->data +
offset);
offset += sizeof(u32);
But the problematic patch calculates:
offset = ((rx->remaining + 1) & 0xfffe) + sizeof(u32);
rx->header = get_unaligned_le32(skb->data + offset);
Adding some debug logic to check those offset calculation used
to find rx->header, the one in problematic code is always too
large by sizeof(u32).
Thus, this patch removes the incorrect " + sizeof(u32)" addition
in the problematic calculation, and resolves the issue.
Cc: Dean Jenkins <Dean_Jenkins@mentor.com>
Cc: "David B. Robins" <linux@davidrobins.net>
Cc: Mark Craske <Mark_Craske@mentor.com>
Cc: Emil Goode <emilgoode@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Ivan Vecera <ivecera@redhat.com>
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: stable <stable@vger.kernel.org> #4.4+
Reported-by: Yongqin Liu <yongqin.liu@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull parallel filesystem directory handling update from Al Viro.
This is the main parallel directory work by Al that makes the vfs layer
able to do lookup and readdir in parallel within a single directory.
That's a big change, since this used to be all protected by the
directory inode mutex.
The inode mutex is replaced by an rwsem, and serialization of lookups of
a single name is done by a "in-progress" dentry marker.
The series begins with xattr cleanups, and then ends with switching
filesystems over to actually doing the readdir in parallel (switching to
the "iterate_shared()" that only takes the read lock).
A more detailed explanation of the process from Al Viro:
"The xattr work starts with some acl fixes, then switches ->getxattr to
passing inode and dentry separately. This is the point where the
things start to get tricky - that got merged into the very beginning
of the -rc3-based #work.lookups, to allow untangling the
security_d_instantiate() mess. The xattr work itself proceeds to
switch a lot of filesystems to generic_...xattr(); no complications
there.
After that initial xattr work, the series then does the following:
- untangle security_d_instantiate()
- convert a bunch of open-coded lookup_one_len_unlocked() to calls of
that thing; one such place (in overlayfs) actually yields a trivial
conflict with overlayfs fixes later in the cycle - overlayfs ended
up switching to a variant of lookup_one_len_unlocked() sans the
permission checks. I would've dropped that commit (it gets
overridden on merge from #ovl-fixes in #for-next; proper resolution
is to use the variant in mainline fs/overlayfs/super.c), but I
didn't want to rebase the damn thing - it was fairly late in the
cycle...
- some filesystems had managed to depend on lookup/lookup exclusion
for *fs-internal* data structures in a way that would break if we
relaxed the VFS exclusion. Fixing hadn't been hard, fortunately.
- core of that series - parallel lookup machinery, replacing
->i_mutex with rwsem, making lookup_slow() take it only shared. At
that point lookups happen in parallel; lookups on the same name
wait for the in-progress one to be done with that dentry.
Surprisingly little code, at that - almost all of it is in
fs/dcache.c, with fs/namei.c changes limited to lookup_slow() -
making it use the new primitive and actually switching to locking
shared.
- parallel readdir stuff - first of all, we provide the exclusion on
per-struct file basis, same as we do for read() vs lseek() for
regular files. That takes care of most of the needed exclusion in
readdir/readdir; however, these guys are trickier than lookups, so
I went for switching them one-by-one. To do that, a new method
'->iterate_shared()' is added and filesystems are switched to it
as they are either confirmed to be OK with shared lock on directory
or fixed to be OK with that. I hope to kill the original method
come next cycle (almost all in-tree filesystems are switched
already), but it's still not quite finished.
- several filesystems get switched to parallel readdir. The
interesting part here is dealing with dcache preseeding by readdir;
that needs minor adjustment to be safe with directory locked only
shared.
Most of the filesystems doing that got switched to in those
commits. Important exception: NFS. Turns out that NFS folks, with
their, er, insistence on VFS getting the fuck out of the way of the
Smart Filesystem Code That Knows How And What To Lock(tm) have
grown the locking of their own. They had their own homegrown
rwsem, with lookup/readdir/atomic_open being *writers* (sillyunlink
is the reader there). Of course, with VFS getting the fuck out of
the way, as requested, the actual smarts of the smart filesystem
code etc. had become exposed...
- do_last/lookup_open/atomic_open cleanups. As the result, open()
without O_CREAT locks the directory only shared. Including the
->atomic_open() case. Backmerge from #for-linus in the middle of
that - atomic_open() fix got brought in.
- then comes NFS switch to saner (VFS-based ;-) locking, killing the
homegrown "lookup and readdir are writers" kinda-sorta rwsem. All
exclusion for sillyunlink/lookup is done by the parallel lookups
mechanism. Exclusion between sillyunlink and rmdir is a real rwsem
now - rmdir being the writer.
Result: NFS lookups/readdirs/O_CREAT-less opens happen in parallel
now.
- the rest of the series consists of switching a lot of filesystems
to parallel readdir; in a lot of cases ->llseek() gets simplified
as well. One backmerge in there (again, #for-linus - rockridge
fix)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (74 commits)
ext4: switch to ->iterate_shared()
hfs: switch to ->iterate_shared()
hfsplus: switch to ->iterate_shared()
hostfs: switch to ->iterate_shared()
hpfs: switch to ->iterate_shared()
hpfs: handle allocation failures in hpfs_add_pos()
gfs2: switch to ->iterate_shared()
f2fs: switch to ->iterate_shared()
afs: switch to ->iterate_shared()
befs: switch to ->iterate_shared()
befs: constify stuff a bit
isofs: switch to ->iterate_shared()
get_acorn_filename(): deobfuscate a bit
btrfs: switch to ->iterate_shared()
logfs: no need to lock directory in lseek
switch ecryptfs to ->iterate_shared
9p: switch to ->iterate_shared()
fat: switch to ->iterate_shared()
romfs, squashfs: switch to ->iterate_shared()
more trivial ->iterate_shared conversions
...
|
|
The problem is that fib_info->nh is [0] so the struct fib_info
allocation size depends on number of nexthops. If we just copy fib_info,
we do not copy the nexthops info and driver accesses memory which is not
ours.
Given the fact that fib4 does not defer operations and therefore it does
not need copy, just pass the pointer down to drivers as it was done
before.
Fixes: 850d0cbc91 ("switchdev: remove pointers from switchdev objects")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This update delivers:
- Yet another interrupt chip diver (LPC32xx)
- Core functions to handle partitioned per-cpu interrupts
- Enhancements to the IPI core
- Proper handling of irq type configuration
- A large set of ARM GIC enhancements
- The usual pile of small fixes, cleanups and enhancements"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
irqchip/bcm2836: Use a more generic memory barrier call
irqchip/bcm2836: Fix compiler warning on 64-bit build
irqchip/bcm2836: Drop smp_set_ops on arm64 builds
irqchip/gic: Add helper functions for GIC setup and teardown
irqchip/gic: Store GIC configuration parameters
irqchip/gic: Pass GIC pointer to save/restore functions
irqchip/gic: Return an error if GIC initialisation fails
irqchip/gic: Remove static irq_chip definition for eoimode1
irqchip/gic: Don't initialise chip if mapping IO space fails
irqchip/gic: WARN if setting the interrupt type for a PPI fails
irqchip/gic: Don't unnecessarily write the IRQ configuration
irqchip: Mask the non-type/sense bits when translating an IRQ
genirq: Ensure IRQ descriptor is valid when setting-up the IRQ
irqchip/gic-v3: Configure all interrupts as non-secure Group-1
irqchip/gic-v2m: Add workaround for Broadcom NS2 GICv2m erratum
irqchip/irq-alpine-msi: Don't use <asm-generic/msi.h>
irqchip/mbigen: Checking for IS_ERR() instead of NULL
irqchip/gic-v3: Remove inexistant register definition
irqchip/gicv3-its: Don't allow devices whose ID is outside range
irqchip: Add LPC32xx interrupt controller driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"A rather small set of patches from the timer departement:
- Some more y2038 work
- Yet another new clocksource driver
- The usual set of small fixes, cleanups and enhancements"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/tegra: Remove unused suspend/resume code
clockevents/driversi/mps2: add MPS2 Timer driver
dt-bindings: document the MPS2 timer bindings
clocksource/drivers/mtk_timer: Add __init attribute
clockevents/drivers/dw_apb_timer: Implement ->set_state_oneshot_stopped()
time: Introduce do_sys_settimeofday64()
security: Introduce security_settime64()
clocksource: Add missing include of of.h.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Crypto self tests can now be disabled at boot/run time.
- Add async support to algif_aead.
Algorithms:
- A large number of fixes to MPI from Nicolai Stange.
- Performance improvement for HMAC DRBG.
Drivers:
- Use generic crypto engine in omap-des.
- Merge ppc4xx-rng and crypto4xx drivers.
- Fix lockups in sun4i-ss driver by disabling IRQs.
- Add DMA engine support to ccp.
- Reenable talitos hash algorithms.
- Add support for Hisilicon SoC RNG.
- Add basic crypto driver for the MXC SCC.
Others:
- Do not allocate crypto hash tfm in NORECLAIM context in ecryptfs"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (77 commits)
crypto: qat - change the adf_ctl_stop_devices to void
crypto: caam - fix caam_jr_alloc() ret code
crypto: vmx - comply with ABIs that specify vrsave as reserved.
crypto: testmgr - Add a flag allowing the self-tests to be disabled at runtime.
crypto: ccp - constify ccp_actions structure
crypto: marvell/cesa - Use dma_pool_zalloc
crypto: qat - make adf_vf_isr.c dependant on IOV config
crypto: qat - Fix typo in comments
lib: asn1_decoder - add MODULE_LICENSE("GPL")
crypto: omap-sham - Use dma_request_chan() for requesting DMA channel
crypto: omap-des - Use dma_request_chan() for requesting DMA channel
crypto: omap-aes - Use dma_request_chan() for requesting DMA channel
crypto: omap-des - Integrate with the crypto engine framework
crypto: s5p-sss - fix incorrect usage of scatterlists api
crypto: s5p-sss - Fix missed interrupts when working with 8 kB blocks
crypto: s5p-sss - Use common BIT macro
crypto: mxc-scc - fix unwinding in mxc_scc_crypto_register()
crypto: mxc-scc - signedness bugs in mxc_scc_ablkcipher_req_init()
crypto: talitos - fix ahash algorithms registration
crypto: ccp - Ensure all dependencies are specified
...
|
|
For ethernet devices, net_device.name will be eth%d before
register_netdev() is called. Don't print the net_device name until
the format string is replaced.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Barry Song <Baohua.Song@csr.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the necessary driver support for Management Firmware to
configure the device/firmware with the dcbx results. Management Firmware
is responsible for communicating the DCBX and driving the negotiation,
but the driver has responsibility of receiving async notification and
configuring the results in hw/fw. This patch also adds the dcbx support for
future protocols (e.g., FCoE) as preparation to their imminent submission.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reopening the network device on ra7795/salvator-x, e.g. after a
DHCP timeout:
IP-Config: Reopening network devices...
genirq: Flags mismatch irq 139. 00000000 (eth0:ch0:rx_be) vs. 00000000 (ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch0:rx_be
IP-Config: Failed to open eth0
IP-Config: No network devices available
The "mismatch" is due to requesting an IRQ that is already in use,
while IRQF_PROBE_SHARED wasn't set.
However, the real cause is that ravb_close() doesn't release any of the
R-Car Gen3-specific secondary IRQs.
Add the missing free_irq() calls to fix this.
Fixes: f51bdc236b6c5835 ("ravb: Add dma queue interrupt support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This line was indented more than it should be.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-05-16
This series contains 2 fixes to ixgbe only.
Emil fixes transmit hangs when enabling SRIOV by swapping the parameters
in GENMASK in order to generate the correct mask.
Alex fixes his previous patch b83e30104bd9 ("ixgbe/ixgbevf: Add support
for GSO partial") where he somehow transposed the location of setting
the VLAN features in netdev->features and the configuration of the
vlan_features.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-tuning is not possible when switched to the RPMB
partition. However re-tuning should not be needed
if re-tuning is done immediately before switching,
a small set of operations is done, and then we
immediately switch back to the main partition.
A previous patch ensured that we immediately switch
back to the main partition.
This patch uses the new facility to "pause" re-tuning
before switching to the RPMB partition, and to "unpause"
it after switching from the RPMB partition.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In preparation to support the use of the RPMB partition with transfer
modes that might require re-tuning, always switch back to the main
area after RPMB access.
RPMB is accessible only via IOCTL so only those paths are affected.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Re-tuning is not possible when switched to the RPMB
partition. However re-tuning should not be needed
if re-tuning is done immediately before switching,
a small set of operations is done, and then we
immediately switch back to the main partition.
To ensure that re-tuning can't be done for a short
while, add a facility to "pause" re-tuning.
The existing facility to hold / release re-tuning
is used but it also flags re-tuning as needed to cause
re-tuning before the next command (which will be the
switch to RPMB).
We also need to "unpause" in the recovery path, which
is catered for by adding it to mmc_retune_disable().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
TEMPSI_CFG is not equal to 0 at reset. It must be initialized.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Documentation/timers/timers-howto.txt recommends to use
usleep_range on delays > 10usec.
The usleep_range indeed reduces CPU load, since the udelay will busy wait
for enough loop cycles to achieve the desired delay.
Fixes commit b06c52db39fd ("thermal: rockchip:
handle the power sequence for tsadc controller").
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Suggested-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
To update the notes for keeping in mind that quickly in case
someone re-read this driver in the future.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The RK3366 SoCs have two Temperature Sensors, channel 0 is for CPU
channel 1 is for GPU.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This adds the grf property to handle the tsadc power sequence on
rockchip some SoCs.
Verified on rk3399 can work with this patch on now.
while true; do grep "" /sys/class/thermal/thermal_zone[0-1]/temp
sleep .5; done
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41666
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
/sys/class/thermal/thermal_zone1/temp:41111
/sys/class/thermal/thermal_zone0/temp:40555
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This patch fixes the incorrect conversion table.
The Code to Temperature mapping is updated based on sillcon results.
Fixes commit b0d70338bca22cb14
("thermal: rockchip: Support the RK3399 SoCs in thermal driver").
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
We should judge the table.id[mid].code insearch algorithm on matter the
adc value increment or decrement.
Or otherwise, the temperature return the incorrect value in some cases.
[ 1.438589] adc_val=402,temp=-40000
[ 1.438903] adc_val=403,temp=-39375
[ 1.439217] adc_val=404,temp=-38750
...
[ 1.441102] adc_val=410,temp=-40000
[ 1.441416] adc_val=411,temp=-34445
[ 1.441737] adc_val=412,temp=-33889
...
Let's fix it right now.
Fixes commit 020ba95dbbbe ("thermal: rockchip:
Add the sort mode for adc value increment or decrement").
Reported-by: Rocky Hao <rocky.hao@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Disable thermal->clk when enabling pclk fails in
resume routine.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
add Tegra132 specific SOC_THERM driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
drivers/thermal/tango_thermal.c:86:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
CC: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
MT8173 cpufreq driver select of_cpufreq_power_cooling_register registering
cooling devices with dynamic power coefficient.
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dawei Chien <dawei.chien@mediatek.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
In some of platform, thermal sensors like NCT thermistors are
connected to the one of ADC channel. The temperature is read by
reading the voltage across the sensor resistance via ADC. Lookup
table for ADC read value to temperature is referred to get
temperature. ADC is read via IIO framework.
Add support for thermal sensor driver which read the voltage across
sensor resistance from ADC through IIO framework.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
There has a static checker warning:
warn: variable dereferenced before check 'dev' (see line 222)
Since check 'dev' is unnecessary, so remove this check.
Fixes: ee6d79f202a4 ("thermal: tegra: add thermtrip function")
Signed-off-by: Wei Ni <wni@nvidia.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
After the PM support has been added to this driver, we get
a harmless warning when that support is disabled at compile
time:
drivers/thermal/tegra/soctherm.c:641:12: error: 'soctherm_resume' defined but not used [-Werror=unused-function]
static int soctherm_resume(struct device *dev)
This marks the two PM functions as __maybe_unused to shut up
the warning. This is preferred over adding an #ifdef around
them, as it is harder to get wrong, and provides better
compile-time coverage.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: a134b4143b65 ("thermal: tegra: add PM support")
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The Tango thermal driver provides support for the primitive temperature
sensor embedded in Tango chips since the SMP8758.
This sensor only generates a 1-bit signal to indicate whether the die
temperature exceeds a programmable threshold.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
When register sensors into thermal zone during initialization phase, it
reports error for IRQ imbalance enabling:
[ 2.040713] WARNING: at kernel/irq/manage.c:513
[ 2.040719] Modules linked in:
[ 2.040721]
[ 2.040729] CPU: 1 PID: 804 Comm: irq/33-hisi_the Not tainted 4.5.0-rc4+ #505
[ 2.040732] Hardware name: HiKey Development Board (DT)
[ 2.040736] task: ffffffc03ae82580 ti: ffffffc0379c8000 task.ti: ffffffc0379c8000
[ 2.040745] PC is at __enable_irq+0x74/0x84
[ 2.040749] LR is at __enable_irq+0x74/0x84
This warning is for IRQ imbalance enabling, which is caused by
enable_irq() twice. During sensor's initialization it tries to enable
IRQ, the driver will call thermal_zone_of_sensor_register() to bind
sensors and read sensor's temperature. But at this moment the flag
"data->irq_enabled" has been not initialized as correct state, so it
finally introduces the function enabled_irq() to be called twice. In
essentially this is caused by the flag "data->irq_enabled" is
inconsistent with real hardware IRQ enabling state.
So this patch is to fix this issue, firstly init "irq_enabled" flag
before binding sensors to thermal zone. Also change to use the function
irq_get_irqchip_state() to read back real interrupt line state.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
In current code sensor driver registers all 4 sensors together and if
any of them has not bound to thermal zone successfully then driver will
return failure for driver's initialization. As a result, if DT binds
thermal zone with only one sensor, then the thermal driver will not work
well anymore.
So this patch is to fix this issue. It allows the thermal sensor driver
can register any number sensors at initialization phase, and fix up code
for other related code to skip related sensor's accessing if the sensor
has not been enabled in initialization phase.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Add suspend/resume function in soctherm driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Handle HW initialization in one function soctherm_init(),
so that the codes are more clear.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Handle clock enable/disable codes in one function
soctherm_clk_enable(), so that the codes are more clear.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Add support for hardware critical thermal limits to the
SOC_THERM driver. It use the Linux thermal framework to
create critical trip temp, and set it to SOC_THERM hardware.
If these limits are breached, the chip will reset, and if
appropriately configured, will turn off the PMIC.
This support is critical for safe usage of the chip.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
In current of-thermal, the .set_trip_temp only support to
set trip_temp for SW. But some sensors support to set
trip_temp on hardware, so that can trigger interrupt,
shutdown or any other events.
This patch adds .set_trip_temp() callback in
thermal_zone_of_device_ops{}, so that the sensor device can
use it to set trip_temp on hardware.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Add a debugfs interface to show register contents for debug.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Add Tegra210 specific SOC_THERM driver.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Split most of the Tegra124 data and code into a Tegra124-specific
file.
Split most of the fuse-related code into a fuse-related source file.
This is in preparation for adding a Tegra210-specific driver in a
future patch.
Beyond the maintainability improvements, this is intended to separate
chip-specific ATE and characterization-related hacks into chip-specific
files, in the hopes that they won't pollute code for other chips.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Get rid of T124-specific PDIV/HOTSPOT hack.
tegra-soctherm.c contained a hack to set the SENSOR_PDIV and
SENSOR_HOTSPOT_OFFSET registers - it just did two writes of
T124-specific opaque values. Convert these into a form that can be
substituted on a per-chip basis, and into structure fields that have
at least some independent meaning.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Combine sensor group-related data structures into struct
tegra_tsensor_group. This provides a single location for
sensor group data storage.
More sensor group data will be added in subsequent patches.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
Move Tegra soctherm driver to tegra directory, it's easy to maintain
and add more new function support for Tegra platforms.
This will also help to split soctherm driver into common parts and
chip specific data related parts.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Tested-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
This changes the driver to use the devm_ version
of thermal_zone_of_sensor_register and cleans
up the local points and unregister calls.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
