| Age | Commit message (Collapse) | Author |
|---|
|
Pull out bus access locking code into separate functions, this is done
in preparation for unifying the driver with the parallel bus one. The
parallel bus driver does not need heavy mutex locking of the bus and
works better with spinlocks, hence prepare these locking functions to
be overridden then.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RXFC register is the only one being read using 8-bit accessors.
To make it easier to support the 16-bit accesses used by the parallel
bus variant of KS8851, use 16-bit accessor to read RXFC register as
well as neighboring RXFCTR register.
Remove ks8851_rdreg8() as it is not used anywhere anymore.
There should be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the SPI variant of KS8851, the MAC address can be programmed with
either 8/16/32-bit writes. To make it easier to support the 16-bit
parallel option of KS8851 too, switch both the MAC address programming
and readout to 16-bit operations.
Remove ks8851_wrreg8() as it is not used anywhere anymore.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851_rdreg32() is used only in one place, to read two registers
using a single read. To make it easier to support 16-bit accesses via
parallel bus later on, replace this single read with two 16-bit reads
from each of the registers and drop the ks8851_rdreg32() altogether.
If this has noticeable performance impact on the SPI variant of KS8851,
then we should consider using regmap to abstract the SPI and parallel
bus options and in case of SPI, permit regmap to merge register reads
of neighboring registers into single, longer, read.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace spi_{get,set}_drvdata() with dev_{get,set}_drvdata(), which
works for both SPI and platform drivers. This is done in preparation
for unifying the KS8851 SPI and parallel bus drivers.
There should be no functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use device managed version of alloc_etherdev() to simplify the code.
No functional change intended.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the driver probe function already has a struct device *dev pointer
and can easily derive of_node pointer from it, pass the of_node pointer as
a parameter to ks8851_init_mac() to avoid fishing it out from ks->spidev.
This is the only reference to spidev in the function, so get rid of it.
This is done in preparation for unifying the KS8851 SPI and parallel bus
drivers.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_err() instead of dev_err() to avoid accessing the spidev->dev
in the interrupt handler. This is the only place which uses the spidev
in this function, so replace it with netdev_err() to get rid of it. This
is done in preparation for unifying the KS8851 SPI and parallel drivers.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename ndev variable to netdev for the sake of consistency.
No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull out the spi->dev into one common place in the function instead of
having it repeated over and over again. This is done in preparation for
unifying ks8851 and ks8851-mll drivers. No functional change.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With all vmxnet3 version 4 changes incorporated in the vmxnet3 driver,
the driver can configure emulation to run at vmxnet3 version 4, provided
the emulation advertises support for version 4.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vmxnet3 version 3 device supports checksum/TSO offload. Thus, vNIC to
pNIC traffic can leverage hardware checksum/TSO offloads. However,
vmxnet3 does not support checksum/TSO offload for Geneve/VXLAN
encapsulated packets. Thus, for a vNIC configured with an overlay, the
guest stack must first segment the inner packet, compute the inner
checksum for each segment and encapsulate each segment before
transmitting the packet via the vNIC. This results in significant
performance penalty.
This patch will enhance vmxnet3 to support Geneve/VXLAN TSO as well as
checksum offload.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With vmxnet3 version 4, the emulation supports multiqueue(RSS) for
UDP and ESP traffic. A guest can enable/disable RSS for UDP/ESP over
IPv4/IPv6 by issuing commands introduced in this patch. ESP ipv6 is
not yet supported in this patch.
This patch implements get_rss_hash_opts and set_rss_hash_opts
methods to allow querying and configuring different Rx flow hash
configurations.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vmxnet3 is currently at version 3 and this patch initiates the
preparation to accommodate changes for version 4. Introduced utility
macros for vmxnet3 version 4 comparison and update Copyright
information.
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when a VF VSI calls ice_vsi_release() and ice_vsi_setup() it
subsequently clears/sets the VF cached variables for lan_vsi_idx and
lan_vsi_num. This works fine, but can be improved by handling this in
the VF specific VSI release and setup functions.
Also, when a VF VSI is setup too many parameters are passed that can be
derived from the VF. Fix this by only calling VF VSI setup with the bare
minimum parameters.
Also, add functionality to invalidate a VF's VSI when it's released
and/or setup fails. This will make it so a VF VSI cannot be accessed via
its cached vsi_idx/vsi_num in these cases.
Finally when a VF's VSI is invalidated set the lan_vsi_idx and
lan_vsi_num to ICE_NO_VSI to clearly show that there is no valid VSI
associated with this VF.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently VF VSI are being reset twice during a PFR or greater. This is
causing reset, specifically resetting all VFs, to take too long. This is
causing various issues with VF drivers not being able to gracefully
handle the VF reset timeout. Fix this by refactoring how VF reset is
handled for the case mentioned previously and for the VFR/VFLR case.
The refactor was done by doing the following:
1. Removing the call to ice_vsi_rebuild_by_type for
ICE_VSI_VF VSI, which was causing the initial VSI rebuild.
2. Adding functions for pre/post VSI rebuild functions that can be called
in both the reset all VFs case and reset individual VF case.
3. Adding VSI rebuild functions that are specific for the reset all VFs
case and adding functions that are specific for the reset individual
VF case.
4. Calling the pre-rebuild function, then the specific VSI rebuild
function based on the reset type, and then calling the post-rebuild
function to handle VF resets.
This patch series makes some assumptions about how VSI are handling by
FW during reset:
1. During a PFR or greater all VSI in FW will be cleared.
2. During a VFR/VFLR the VSI rebuild responsibility is in the hands of
the PF software.
3. There is code in the ice_reset_all_vfs() case to amortize operations
if possible. This was left intact.
4. PF software should not be replaying VSI based filters that were added
other than host configured, PF software configured, or the VF's
default/LAA MAC. This is the VF drivers job after it has been reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
1.The SSI clock of X1000 not like JZ4770 and JZ4780, they are not
directly derived from the output of SSIPLL, but from the clock
obtained by dividing the frequency by 2. "X1000_CLK_SSIPLL_DIV2"
is added for this purpose, and ensure that it initialized before
"X1000_CLK_SSIMUX" when initializing the clocks.
2.Clocks of LCD, OTG, EMC, EFUSE, OST, TCU, and gates of CPU, PCLK
are also added.
3.Use "CLK_OF_DECLARE_DRIVER" like the other CGU drivers.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-8-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Add support for the clocks provided by the CGU in the Ingenic X1830
SoC, making use of the cgu code to do the heavy lifting.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-6-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The PLL of X1830 Soc from Ingenic has been greatly changed,
the bypass control is placed in another register, so now two
registers may needed to control the PLL. To this end, a new
"bypass_reg" was introduced. In addition, when calculating
rate, the PLL of X1830 introduced an extra 2x multiplier,
so a new "rate_multiplier" was introduced. And adjust the
code in jz47xx-cgu.c and x1000-cgu.c, make it to be
compatible with the new cgu code.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-3-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
It is not necessary to use spinlock when reading registers,
so remove it from cgu.c.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Paul Burton <paulburton@kernel.org>
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lkml.kernel.org/r/20200528031549.13846-2-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Remove VM/VF disable AQC (opcode 0x0C31) when resetting all VFs.
This is not required for CORER/GLOBR reset.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When resetting a VF the VLAN and MAC filter configurations need to be
replayed. Add helper functions for this purpose.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As the title says, use a function to set trust mode bit on reset.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Some function names weren't very clear and some portions of VF creation
could be moved into functions for clarity. Fix this by renaming some
functions and move pieces of code into clearly name functions.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the same flow is used for VF VSI initialization/creation and VF
VSI reset. This makes the initialization/creation flow unnecessarily
complicated. Fix this by separating the initialization/creation of the
VF VSI from the reset flow.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The variable rate64 is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lkml.kernel.org/r/20200528221219.535804-1-colin.king@canonical.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Create a helper function for clearing VPGEN_VFRTRIG as this needs to be
done on reset to notify the VF that we are done resetting it. Also, it
needs to be done on SR-IOV initialization/creation in case it was left
in a bad state after SR-IOV tear down.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The kbuild test robot is firing a warning over a missing prototype. The
function can just be static.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
GCC warns about this comparison, which is unnecessary.
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
|
|
Add a new function for checking if SR-IOV can be configured based on
the PF and/or device's state/capabilities. Also, simplify the flow in
ice_sriov_configure().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently ice_ena_vf_mappings() does all of the VF's MSIX and queue
mapping in one function. This makes it hard to digest. Fix this by
creating a new function for enabling MSIX mappings and one for enabling
queue mappings.
Also, rename some variables in the functions for clarity.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ice_get_pfa_module_tlv() and ice_read_sr_word() are not being called
outside of their file. Declare them as static.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If register_netdev() fails, the driver will attempt to cleanup the
q_vectors and inadvertently trigger a kernel BUG due to a NULL pointer
dereference.
This occurs because cleaning up q_vectors attempts to call
netif_napi_del on napi_structs which were never initialized.
Resolve this by releasing the netdev in ice_cfg_netdev and setting
vsi->netdev to NULL. This ensures that after ice_cfg_netdev fails the
state is rewound to match as if ice_cfg_netdev was never called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If ice_init_interrupt_scheme fails, ice_probe will jump to clearing up
the interrupts. This can lead to some static analysis tools such as the
compiler sanitizers complaining about double free problems.
Since ice_init_interrupt_scheme already unrolls internally on failure,
there is no need to call ice_clear_interrupt_scheme when it fails. Add
a new unroll label and use that instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove an unnecessary copy of vsi->info into ctxt->info in ice_vsi_init.
This line is essentially a no-op because ice_set_dflt_vsi_ctx performs
a memset to clear the info from the context structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There are certain cases where the DDP load fails and the FW issues a
core reset. For these cases, wait for reset to complete before
proceeding with reset of the driver init.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
sbs-battery does not use the ID parameter, so switch to i2c's
probe_new API.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Switch from DT specific of_property_* API to generic and more
modern device_property_* API.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In certain designs, it is possible to add a battery on a populated i2c
bus without an sbs compliant charger. In that case, the battery will
unnecessarily and sometimes undesirably master the bus trying to write
info in the charger.
It is observed in many occasion that these battery "broadcasts" are even
corrupting other ongoing master to slave communication. I.e. the
multi-master support in the battery is inadequate.
Thankfully, the CHARGER_MODE bit allows designers to disable that SBS
battery behaviour.
This needs to be done once when the battery is first seen on the bus.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
[rebased code]
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
A battery, that is neither charged, nor discharged is not
always Full. If the charger is disabled for other reasons
it might simply be idle and should be marked accordingly.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for reporting the SBS battery's condition flag
to userspace using the new "Calibration required" health status.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Expose the battery's manufacture date to userspace.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT/VOLTAGE_MAX support
Expose maximum charge current/voltage information requested
by the battery.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This reads the battery chemistry from the battery chip instead
of incorrectly hardcoding the type to be Li-Ion.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Expose averaged current information, which is part of the SBS
standard and should be supported by all batteries.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
SBS batteries optionally have support for PEC. This enables
PEC handling based on the implemented SBS version as suggested
by the standard. The support for PEC is re-evaluated when the
battery is hotplugged into the system, since there might be
systems supporting batteries from different SBS generations.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The SBS battery implements SMBus block reads. Currently the
driver "emulates" this by doing an I2C byte read for the
length followed by an I2C block read. The I2C subsystem
actually provides a proper API for doing SMBus block reads,
which can and should be used instead. The current implementation
does not properly handle packet error checking (PEC).
This change requires, that I2C bus drivers support I2C_M_RECV_LEN
or directly provide the SMBus API to access device manufacturer
and model name.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add support for reporting the MaxError register from
battery fuel gauges following the smart battery standard.
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Added a check such that only singleton IOMMU groups can pin pages.
>From the point when vendor driver pins any pages, consider IOMMU group
dirty page scope to be limited to pinned pages.
To optimize to avoid walking list often, added flag
pinned_page_dirty_scope to indicate if all of the vfio_groups for each
vfio_domain in the domain_list dirty page scope is limited to pinned
pages. This flag is updated on first pinned pages request for that IOMMU
group and on attaching/detaching group.
Signed-off-by: Kirti Wankhede <kwankhede@nvidia.com>
Reviewed-by: Neo Jia <cjia@nvidia.com>
Reviewed-by: Yan Zhao <yan.y.zhao@intel.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
