| Age | Commit message (Collapse) | Author |
|---|
|
The driver triggers a "Secondary Bus Reset" (SBR) by calling
__pci_reset_function_locked() which asserts the SBR bit in the "Bridge
Control Register" in the configuration space of the upstream bridge for
2ms. This is done without locking the configuration space of the
upstream bridge port, allowing user space to access it concurrently.
Linux 6.11 will start warning about such unlocked resets [1][2]:
pcieport 0000:00:01.0: unlocked secondary bus reset via: pci_reset_bus_function+0x51c/0x6a0
Avoid the warning and the concurrent access by locking the configuration
space of the upstream bridge prior to the reset and unlocking it
afterwards.
[1] https://lore.kernel.org/all/171711746953.1628941.4692125082286867825.stgit@dwillia2-xfh.jf.intel.com/
[2] https://lore.kernel.org/all/20240531213150.GA610983@bhelgaas/
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/9937b0afdb50f2f2825945393c94c093c04a5897.1720447210.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
registration
Commit 31a0fa0019b0 ("thermal/debugfs: Pass cooling device state to
thermal_debug_cdev_add()") changed the thermal core to read the current
state of the cooling device as part of the cooling device's
registration. This is incompatible with the current implementation of
the cooling device operations in mlxsw, leading to initialization
failure with errors such as:
mlxsw_spectrum 0000:01:00.0: Failed to register cooling device
mlxsw_spectrum 0000:01:00.0: cannot register bus device
The reason for the failure is that when the get current state operation
is invoked the driver tries to derive the index of the cooling device by
walking a per thermal zone array and looking for the matching cooling
device pointer. However, the pointer is returned from the registration
function and therefore only set in the array after the registration.
The issue was later fixed by commit 1af89dedc8a5 ("thermal: core: Do not
fail cdev registration because of invalid initial state") by not failing
the registration of the cooling device if it cannot report a valid
current state during registration, although drivers are responsible for
ensuring that this will not happen.
Therefore, make sure the driver is able to report a valid current state
for the cooling device during registration by passing to the
registration function a per cooling device private data that already has
the cooling device index populated.
While at it, call thermal_cooling_device_unregister() unconditionally
since the function returns immediately if the cooling device pointer is
NULL.
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/c823c4678b6b7afb902c35b3551c81a053afd110.1720447210.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A forgotten or buggy variable initialization can cause out-of-bounds access
to a register or other item array field. For an overflow, such access would
mangle adjacent parts of the register payload. For an underflow, due to all
variables being unsigned, the access would likely trample unrelated memory.
Since neither is correct, replace these accesses with accesses at the index
of 0, and warn about the issue.
Suggested-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/b988fb265c2f6c1206fe12d5bfdcfa188b7672d1.1720447210.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The commit 6533e558c650 ("i40e: Fix reset path while removing
the driver") introduced a new PF state "__I40E_IN_REMOVE" to block
modifying the XDP program while the driver is being removed.
Unfortunately, such a change is useful only if the ".ndo_bpf()"
callback was called out of the rmmod context because unloading the
existing XDP program is also a part of driver removing procedure.
In other words, from the rmmod context the driver is expected to
unload the XDP program without reporting any errors. Otherwise,
the kernel warning with callstack is printed out to dmesg.
Example failing scenario:
1. Load the i40e driver.
2. Load the XDP program.
3. Unload the i40e driver (using "rmmod" command).
The example kernel warning log:
[ +0.004646] WARNING: CPU: 94 PID: 10395 at net/core/dev.c:9290 unregister_netdevice_many_notify+0x7a9/0x870
[...]
[ +0.010959] RIP: 0010:unregister_netdevice_many_notify+0x7a9/0x870
[...]
[ +0.002726] Call Trace:
[ +0.002457] <TASK>
[ +0.002119] ? __warn+0x80/0x120
[ +0.003245] ? unregister_netdevice_many_notify+0x7a9/0x870
[ +0.005586] ? report_bug+0x164/0x190
[ +0.003678] ? handle_bug+0x3c/0x80
[ +0.003503] ? exc_invalid_op+0x17/0x70
[ +0.003846] ? asm_exc_invalid_op+0x1a/0x20
[ +0.004200] ? unregister_netdevice_many_notify+0x7a9/0x870
[ +0.005579] ? unregister_netdevice_many_notify+0x3cc/0x870
[ +0.005586] unregister_netdevice_queue+0xf7/0x140
[ +0.004806] unregister_netdev+0x1c/0x30
[ +0.003933] i40e_vsi_release+0x87/0x2f0 [i40e]
[ +0.004604] i40e_remove+0x1a1/0x420 [i40e]
[ +0.004220] pci_device_remove+0x3f/0xb0
[ +0.003943] device_release_driver_internal+0x19f/0x200
[ +0.005243] driver_detach+0x48/0x90
[ +0.003586] bus_remove_driver+0x6d/0xf0
[ +0.003939] pci_unregister_driver+0x2e/0xb0
[ +0.004278] i40e_exit_module+0x10/0x5f0 [i40e]
[ +0.004570] __do_sys_delete_module.isra.0+0x197/0x310
[ +0.005153] do_syscall_64+0x85/0x170
[ +0.003684] ? syscall_exit_to_user_mode+0x69/0x220
[ +0.004886] ? do_syscall_64+0x95/0x170
[ +0.003851] ? exc_page_fault+0x7e/0x180
[ +0.003932] entry_SYSCALL_64_after_hwframe+0x71/0x79
[ +0.005064] RIP: 0033:0x7f59dc9347cb
[ +0.003648] Code: 73 01 c3 48 8b 0d 65 16 0c 00 f7 d8 64 89 01 48 83
c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa b8 b0 00 00 00 0f
05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 35 16 0c 00 f7 d8 64 89 01 48
[ +0.018753] RSP: 002b:00007ffffac99048 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ +0.007577] RAX: ffffffffffffffda RBX: 0000559b9bb2f6e0 RCX: 00007f59dc9347cb
[ +0.007140] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 0000559b9bb2f748
[ +0.007146] RBP: 00007ffffac99070 R08: 1999999999999999 R09: 0000000000000000
[ +0.007133] R10: 00007f59dc9a5ac0 R11: 0000000000000206 R12: 0000000000000000
[ +0.007141] R13: 00007ffffac992d8 R14: 0000559b9bb2f6e0 R15: 0000000000000000
[ +0.007151] </TASK>
[ +0.002204] ---[ end trace 0000000000000000 ]---
Fix this by checking if the XDP program is being loaded or unloaded.
Then, block only loading a new program while "__I40E_IN_REMOVE" is set.
Also, move testing "__I40E_IN_REMOVE" flag to the beginning of XDP_SETUP
callback to avoid unnecessary operations and checks.
Fixes: 6533e558c650 ("i40e: Fix reset path while removing the driver")
Signed-off-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240708230750.625986-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A previous commit ("PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper")
removed the dw_pcie_ep_init_notify() wrapper and changed the DWC glue
drivers to instead use pci_epc_init_notify() directly.
The endpoint support for the dw-rockchip had not been merged at that point
in time, so the previous commit wrapper") did not update dw-rockchip.
Do the same change for dw-rockchip, so that the driver will not try
to use a function that has now been removed.
Link: https://lore.kernel.org/linux-pci/20240622132024.2927799-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The PCIe controller in rk3568 and rk3588 can operate in endpoint mode.
This endpoint mode support heavily leverages the existing code in
pcie-designware-ep.c.
Add support for endpoint mode to the existing pcie-dw-rockchip glue
driver.
[kwilczynski: squash with patch adding the PCI_ENDPOINT dependency]
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-10-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Refactor the driver to prepare for EP mode.
Add of-match data to the existing compatible, and explicitly define it as
DW_PCIE_RC_TYPE. This way, we will be able to add EP mode in a follow-up
commit in a much less intrusive way, which makes the follow-up commit much
easier to review.
No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-9-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add a rockchip_pcie_ltssm() helper function that reads the LTSSM status.
This helper will be used in additional places in follow-up commits.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-8-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Fix the indentation of rockchip_pcie_{readl,writel}_apb() parameters to
match the opening parenthesis.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-7-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
PERST# is active low according to the PCIe specification.
However, the existing pcie-dw-rockchip.c driver does:
gpiod_set_value(..., 0); msleep(100); gpiod_set_value(..., 1);
when asserting + deasserting PERST#.
This is of course wrong, but because all the device trees for this
compatible string have also incorrectly marked this GPIO as ACTIVE_HIGH:
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3568*
$ git grep -B 10 reset-gpios arch/arm64/boot/dts/rockchip/rk3588*
The actual toggling of PERST# is correct, and we cannot change it anyway,
since that would break device tree compatibility.
However, this driver does request the GPIO to be initialized as
GPIOD_OUT_HIGH, which does cause a silly sequence where PERST# gets
toggled back and forth for no good reason.
Fix this by requesting the GPIO to be initialized as GPIOD_OUT_LOW (which
for this driver means PERST# asserted).
This will avoid an unnecessary signal change where PERST# gets deasserted
(by devm_gpiod_get_optional()) and then gets asserted (by
rockchip_pcie_start_link()) just a few instructions later.
Before patch, debug prints on EP side, when booting RC:
[ 845.606810] pci: PERST# asserted by host!
[ 852.483985] pci: PERST# de-asserted by host!
[ 852.503041] pci: PERST# asserted by host!
[ 852.610318] pci: PERST# de-asserted by host!
After patch, debug prints on EP side, when booting RC:
[ 125.107921] pci: PERST# asserted by host!
[ 132.111429] pci: PERST# de-asserted by host!
This extra, very short, PERST# assertion + deassertion has been reported to
cause issues with certain WLAN controllers, e.g. RTL8822CE.
Fixes: 0e898eb8df4e ("PCI: rockchip-dwc: Add Rockchip RK356X host controller driver")
Link: https://lore.kernel.org/linux-pci/20240417164227.398901-1-cassel@kernel.org
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jianfeng Liu <liujianfeng1994@gmail.com>
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # v5.15+
|
|
Drivers that silently fail to probe provide a bad user experience and
make it unnecessarily hard to debug such a failure.
Fix it by using dev_err_probe() instead of a plain return.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240227141256.413055-2-ukleinek@debian.org
Signed-off-by: Uwe Kleine-König <ukleinek@debian.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Jesper Nilsson <jesper.nilsson@axis.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Rockchip platforms use 'GPIO_ACTIVE_HIGH' flag in the devicetree definition
for ep_gpio. This means, whatever the logical value set by the driver for
the ep_gpio, physical line will output the same logic level.
For instance,
gpiod_set_value_cansleep(rockchip->ep_gpio, 0); --> Level low
gpiod_set_value_cansleep(rockchip->ep_gpio, 1); --> Level high
But while requesting the ep_gpio, GPIOD_OUT_HIGH flag is currently used.
Now, this also causes the physical line to output 'high' creating trouble
for endpoint devices during host reboot.
When host reboot happens, the ep_gpio will initially output 'low' due to
the GPIO getting reset to its POR value. Then during host controller probe,
it will output 'high' due to GPIOD_OUT_HIGH flag. Then during
rockchip_pcie_host_init_port(), it will first output 'low' and then 'high'
indicating the completion of controller initialization.
On the endpoint side, each output 'low' of ep_gpio is accounted for PERST#
assert and 'high' for PERST# deassert. With the above mentioned flow during
host reboot, endpoint will witness below state changes for PERST#:
(1) PERST# assert - GPIO POR state
(2) PERST# deassert - GPIOD_OUT_HIGH while requesting GPIO
(3) PERST# assert - rockchip_pcie_host_init_port()
(4) PERST# deassert - rockchip_pcie_host_init_port()
Now the time interval between (2) and (3) is very short as both happen
during the driver probe(), and this results in a race in the endpoint.
Because, before completing the PERST# deassertion in (2), endpoint got
another PERST# assert in (3).
A proper way to fix this issue is to change the GPIOD_OUT_HIGH flag in (2)
to GPIOD_OUT_LOW. Because the usual convention is to request the GPIO with
a state corresponding to its 'initial/default' value and let the driver
change the state of the GPIO when required.
As per that, the ep_gpio should be requested with GPIOD_OUT_LOW as it
corresponds to the POR value of '0' (PERST# assert in the endpoint). Then
the driver can change the state of the ep_gpio later in
rockchip_pcie_host_init_port() as per the initialization sequence.
This fixes the firmware crash issue in Qcom based modems connected to
Rockpro64 based board.
Fixes: e77f847df54c ("PCI: rockchip: Add Rockchip PCIe controller support")
Closes: https://lore.kernel.org/mhi/20240402045647.GG2933@thinkpad/
Link: https://lore.kernel.org/linux-pci/20240416-pci-rockchip-perst-fix-v1-1-4800b1d4d954@linaro.org
Reported-by: Slark Xiao <slark_xiao@163.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Cc: stable@vger.kernel.org # v4.9
|
|
PCIe r6.0, sec 6.6.1, states that the host should wait for at least 100
msec from the end of a conventional reset (PERST# is de-asserted) before
sending a configuration request to ensure that the device is able to
respond with a "Request Retry Status" completion.
Add the PCIE_T_RRS_READY_MS macro to define this wait time and modify
rockchip_pcie_host_init_port() to add this 100ms sleep after deasserting
PERST# using the ep_gpio GPIO.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-3-dlemoal@kernel.org
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
PCIe CEM r5.1, sec 2.9.2, mandates that the PERST# signal must remain
asserted for at least 100 usec (Tperst-clk) after the PCIe reference clock
becomes stable (if a reference clock is supplied), and for at least 100
msec after the power is stable (Tpvperl, defined by the macro
PCIE_T_PVPERL_MS).
Modify rockchip_pcie_host_init_port() to satisfy these constraints by
adding a sleep period before deasserting PERST# using the ep_gpio GPIO.
Since Tperst-clk is the shorter wait time, add an msleep() call for the
longer PCIE_T_PVPERL_MS milliseconds to handle both timing requirements.
Link: https://lore.kernel.org/linux-pci/20240413004120.1099089-2-dlemoal@kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
From the DWC EP databook 5.96a, section "3.5.7.1.4 General Rules for BAR
Setup (Fixed Mask or Programmable Mask Schemes Only)":
"Any pair (for example BARs 0 and 1) can be configured as one 64-bit BAR,
two 32-bit BARs, or one 32-bit BAR."
"BAR pairs cannot overlap to form a 64-bit BAR. For example, you cannot
combine BARs 1 and 2 to form a 64-bit BAR."
While this limitation does exist in some other PCI endpoint controllers,
e.g. cdns_pcie_ep_set_bar(), the limitation does not appear to be defined
in the PCIe specification itself, thus add an explicit check for this in
dw_pcie_ep_set_bar() (rather than pci_epc_set_bar()).
Link: https://lore.kernel.org/linux-pci/20240528134839.8817-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Down event
Now that dw_pcie_ep_linkdown() is available, use it. This also handles the
reinitialization of DWC non-sticky registers in addition to sending the
notification to EPF drivers.
Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-5-4395534520dc@linaro.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
event
Now that the generic dw_pcie_ep_linkdown() API is available, use it. This
also handles the reinitialization of DWC non-sticky registers in addition
to sending the notification to EPF drivers.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
suspend
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add PCIE_MSG_CODE_PME_TURN_OFF macros to enable a PCIe host driver to send
PME_Turn_Off messages.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-4-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add "Message Routing" and "INTx Mechanism Messages" macros to enable
a PCIe driver to send messages for INTx Interrupt Signaling.
Values from PCIe r6.1, sec 2.2.8 and 2.2.8.1.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-1-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
|
|
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
|
|
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
functions
These two functions are defined in the pci_endpoint_test.c file, but not
called elsewhere, so delete these unused functions.
This fixes the following warning:
drivers/misc/pci_endpoint_test.c:144:19: warning: unused function 'pci_endpoint_test_bar_readl'.
drivers/misc/pci_endpoint_test.c:150:20: warning: unused function 'pci_endpoint_test_bar_writel'.
No functional changes intended.
[kwilczynski: commit log]
Closes: https://bugzilla.openanolis.cn/show_bug.cgi?id=9064
Link: https://lore.kernel.org/linux-pci/20240704023227.87039-1-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add a comment suggesting that if the endpoint controller Vendor and Device
ID are programmable, an existing entry might be usable for testing without
having to add an entry to pci_endpoint_test_tbl[].
Link: https://lore.kernel.org/linux-pci/20240611125057.1232873-6-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
|
|
dma_set_mask_and_coherent() should never fail when the mask is >= 32bit,
unless the architecture has no DMA support. So no need to check for the
error and also no need to set dma_set_mask_and_coherent(32) as a fallback.
Even if dma_set_mask_and_coherent(48) fails due to the lack of DMA support
(theoretically), then dma_set_mask_and_coherent(32) will also fail for the
same reason. So the fallback doesn't make sense.
Simplify the code by setting the streaming and coherent DMA mask to 48
bits.
Link: https://lore.kernel.org/linux-pci/20240502195903.3191049-1-Frank.Li@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
The current code uses writel()/readl(), which has an implicit memory
barrier for every single readl()/writel().
Additionally, reading 4 bytes at a time over the PCI bus is not really
optimal, considering that this code is running in an ioctl handler.
Use memcpy_toio()/memcpy_fromio() for BAR tests.
Before patch with a 4MB BAR:
$ time /usr/bin/pcitest -b 1
BAR1: OKAY
real 0m 1.56s
After patch with a 4MB BAR:
$ time /usr/bin/pcitest -b 1
BAR1: OKAY
real 0m 0.54s
Link: https://lore.kernel.org/linux-pci/20240322164139.678228-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
|
|
Rockchip rk3588 requires 64KB alignment for BARs.
While there is an existing device_id:vendor_id in the driver with 64KB
alignment, that device_id:vendor_id is am654, which uses BAR2 instead of
BAR0 as the test_reg_bar, and also has special is_am654_pci_dev() checks
in the driver to disallow BAR0. In order to allow testing all BARs, add a
new rk3588 entry in the driver.
We intentionally do not add the vendor id to pci_ids.h, since the policy
for that file is that the vendor id has to be used by multiple drivers.
Hopefully, this new entry will be short-lived, as there is a series on the
mailing list which intends to move the address alignment restrictions from
this driver to the endpoint side.
Add a new entry for rk3588 in order to allow us to test all BARs.
Link: https://lore.kernel.org/linux-pci/20240607-rockchip-pcie-ep-v1-v5-11-0a042d6b0049@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Adding support for G761 included adding support for an internal clock.
Enabling the internal clock requires setting a bit in the FAN_CMD2
register. This is implemented in g762_fan_init(). However, g762_fan_init()
is called before clock support is selected, and the flag indicating that
the internal clock should be used is not yet set.
Initialize the clock before initializing the fan to solve the problem.
While at it, also add "g7621" to the i2c_device_id array.
Cc: Christian Marangi <ansuelsmth@gmail.com>
Fixes: 6ce402327a6f ("hwmon: g672: add support for g761")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Convert loops in kirin_pcie_parse_port() to use the _scoped() version of
for_each_available_child_of_node() so the refcounts of children are
implicitly decremented when the loop is exited.
No functional change intended here, but it will make future error exits
from these loops easier.
Link: https://lore.kernel.org/linux-pci/20240609-pcie-kirin-memleak-v1-1-62b45b879576@gmail.com
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: move to GPIO series to avoid bisection hole, commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
QCOM Resource Power Manager-hardened (RPMh) is a hardware block which
maintains hardware state of a regulator by performing max aggregation of
the requests made by all of the clients.
PCIe controller can operate on different RPMh performance state of power
domain based on the speed of the link. And this performance state varies
from target to target, like some controllers support GEN3 in NOM (Nominal)
voltage corner, while some other supports GEN3 in low SVS (static voltage
scaling).
The SoC can be more power efficient if we scale the performance state
based on the aggregate PCIe link bandwidth.
Add Operating Performance Points (OPP) support to vote for RPMh state based
on the aggregate link bandwidth.
OPP can handle ICC bw voting also, so move ICC bw voting through OPP
framework if OPP entries are present.
As we are moving ICC voting as part of OPP, don't initialize ICC if OPP
is supported.
Before PCIe link is initialized vote for highest OPP in the OPP table,
so that we are voting for maximum voltage corner for the link to come up
in maximum supported speed.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-4-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Bring the switch case in pcie_link_speed_mbps() to new function to
the header file so that it can be used in other places like
in controller driver.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-3-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
To access the host controller registers of the host controller and the
endpoint BAR/config space, the CPU-PCIe ICC (interconnect) path should
be voted otherwise it may lead to NoC (Network on chip) timeout.
We are surviving because of other driver voting for this path.
As there is less access on this path compared to PCIe to mem path
add minimum vote i.e 1KBps bandwidth always which is sufficient enough
to keep the path active and is recommended by HW team.
During S2RAM (Suspend-to-RAM), the DBI access can happen very late (while
disabling the boot CPU). So do not disable the CPU-PCIe interconnect path
during S2RAM as that may lead to NoC error.
Link: https://lore.kernel.org/linux-pci/20240619-opp_support-v15-1-aa769a2173a3@quicinc.com
Signed-off-by: Krishna chaitanya chundru <quic_krichai@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
All EP specific resources are enabled during PERST# deassert. As a counter
operation, all resources should be disabled during PERST# assert. There is
no point in skipping that if the link was not enabled.
This will also result in enablement of the resources twice if PERST# got
deasserted again. So remove the check from qcom_pcie_perst_assert() and
disable all the resources unconditionally.
Fixes: f55fee56a631 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-1-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issues exist for
the addressed memory on the host i.e., memory is not cached. But in
reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the host.
And worst case, if the memory is cached on the host, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the host is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-3-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Due to some hardware changes, SA8775P has set the NO_SNOOP attribute
in its TLP for all the PCIe controllers. NO_SNOOP attribute when set,
the requester is indicating that no cache coherency issue exist for
the addressed memory on the endpoint i.e., memory is not cached. But
in reality, requester cannot assume this unless there is a complete
control/visibility over the addressed memory on the endpoint.
And worst case, if the memory is cached on the endpoint, it may lead to
memory corruption issues. It should be noted that the caching of memory
on the endpoint is not solely dependent on the NO_SNOOP attribute in TLP.
So to avoid the corruption, this patch overrides the NO_SNOOP attribute
by setting the PCIE_PARF_NO_SNOOP_OVERIDE register. This patch is not
needed for other upstream supported platforms since they do not set
NO_SNOOP attribute by default.
8775 has IP version 1.34.0 so introduce a new cfg(cfg_1_34_0) for this
platform. Assign override_no_snoop flag into struct qcom_pcie_cfg and
set it true in cfg_1_34_0 and enable cache snooping if this particular
flag is true.
Link: https://lore.kernel.org/linux-pci/1710166298-27144-2-git-send-email-quic_msarkar@quicinc.com
Signed-off-by: Mrinmay Sarkar <quic_msarkar@quicinc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: wrap comments to fit in 80 columns]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add some time to wait for LP engine to complete its operation
before polling pmctrl register.
Signed-off-by: Michael Lo <michael.lo@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Tested-by: David Ruth <druth@chromium.org>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/20240523112131.31437-1-mingyen.hsieh@mediatek.com
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Register MLD capability for the firmware supporting MLO.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/49c796b101e792c84bc2c0d74753022b75fd3355.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
remove the unused function mt7925_mcu_set_chan_info
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/0aa0abe7fc661380ae812c6bc879a7705de401b2.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Update band_idx in per-link BSS to be auto for the MLO-enabled firmware
and the MLO-enabled firmware only supports omac index in 0.
The change remains compatible with the non-MLO mode and the older firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/37fcf3ea7b4883840d61f97231277b297e1b15a3.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
update mt7925_mcu_bss_basic_tlv for the MLO-enabled firmware.
The change remains compatible with the non-MLO mode and the
older firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/583a3ac10583cfef0028f9a0b5a4802fc4070b99.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Set the BSS index from the per-linked BSS for the firmware to identify
which link the command is operating on.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/dde970c748586d03fbecbccb10cb9903284719aa.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
when we serve MLO during the multiple-linked connection, the chanctx may
be not available in the internal driver, we should get the proper the
band information from link_conf for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/6620e00fbeef686fb2041556deba346411eab0f1.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
Get band information from the per-link BSS.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/4f6ca2d082627bb93f79d5a4df80dc08998ee5d2.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
add mt7925_mcu_sta_eht_mld_tlv for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/a1001592eeef4e4ee2c3e15dc94cca0815d64e59.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
update mt7925_mcu_sta_update for the MLO-enabled firmware.
Co-developed-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Signed-off-by: Ming Yen Hsieh <mingyen.hsieh@mediatek.com>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Link: https://patch.msgid.link/2e25bfc2d8aa503ecd1ba8099c6e54dce0c27b99.1720248331.git.sean.wang@kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
