| Age | Commit message (Collapse) | Author |
|---|
|
smack ->d_instantiate() uses ->setxattr(), so to be able to call it before
we'd hashed the new dentry and attached it to inode, we need ->setxattr()
instances getting the inode as an explicit argument rather than obtaining
it from dentry.
Similar change for ->getxattr() had been done in commit ce23e64. Unlike
->getxattr() (which is used by both selinux and smack instances of
->d_instantiate()) ->setxattr() is used only by smack one and unfortunately
it got missed back then.
Reported-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Tested-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pwm config may sleep so defer it using a worker.
On a Freescale i.MX53 based board we ran into "BUG: scheduling while
atomic" because input_inject_event locks interrupts, but
imx_pwm_config_v2 sleeps.
Tested on Freescale i.MX53 SoC with 4.6.0.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
added the according id and incresed XPAD_PKT_LEN to 64 as the elite
controller sends at least 33 byte messages [1].
Verified to be working by [2].
[1]: https://franticrain.github.io/sniffs/XboxOneSniff.html
[2]: https://github.com/paroj/xpad/issues/23
Signed-off-by: Pierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Pierre-Loup A. Griffais <eduke32@plagman.net>
Signed-off-by: Thomas Debesse <dev@illwieckz.net>
Signed-off-by: aronschatz <aronschatz@aselabs.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
After initially connecting a wired Xbox 360 controller or sending it
a command to change LEDs, a status/response packet is interpreted as
controller input. This causes the state of buttons represented in
byte 2 of the controller data packet to be incorrect until the next
valid input packet. Wireless Xbox 360 controllers are not affected.
Writing a new value to the LED device while holding the Start button
and running jstest is sufficient to reproduce this bug. An event will
come through with the Start button released.
Xboxdrv also won't attempt to read controller input from a packet
where byte 0 is non-zero. It also checks that byte 1 is 0x14, but
that value differs between wired and wireless controllers and this
code is shared by both. I think just checking byte 0 is enough to
eliminate unwanted packets.
The following are some examples of 3-byte status packets I saw:
01 03 02
02 03 00
03 03 03
08 03 00
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
otherwise we lose ff commands: https://github.com/paroj/xpad/issues/27
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Most users of IS_ERR_VALUE() in the kernel are wrong, as they
pass an 'int' into a function that takes an 'unsigned long'
argument. This happens to work because the type is sign-extended
on 64-bit architectures before it gets converted into an
unsigned type.
However, anything that passes an 'unsigned short' or 'unsigned int'
argument into IS_ERR_VALUE() is guaranteed to be broken, as are
8-bit integers and types that are wider than 'unsigned long'.
Andrzej Hajda has already fixed a lot of the worst abusers that
were causing actual bugs, but it would be nice to prevent any
users that are not passing 'unsigned long' arguments.
This patch changes all users of IS_ERR_VALUE() that I could find
on 32-bit ARM randconfig builds and x86 allmodconfig. For the
moment, this doesn't change the definition of IS_ERR_VALUE()
because there are probably still architecture specific users
elsewhere.
Almost all the warnings I got are for files that are better off
using 'if (err)' or 'if (err < 0)'.
The only legitimate user I could find that we get a warning for
is the (32-bit only) freescale fman driver, so I did not remove
the IS_ERR_VALUE() there but changed the type to 'unsigned long'.
For 9pfs, I just worked around one user whose calling conventions
are so obscure that I did not dare change the behavior.
I was using this definition for testing:
#define IS_ERR_VALUE(x) ((unsigned long*)NULL == (typeof (x)*)NULL && \
unlikely((unsigned long long)(x) >= (unsigned long long)(typeof(x))-MAX_ERRNO))
which ends up making all 16-bit or wider types work correctly with
the most plausible interpretation of what IS_ERR_VALUE() was supposed
to return according to its users, but also causes a compile-time
warning for any users that do not pass an 'unsigned long' argument.
I suggested this approach earlier this year, but back then we ended
up deciding to just fix the users that are obviously broken. After
the initial warning that caused me to get involved in the discussion
(fs/gfs2/dir.c) showed up again in the mainline kernel, Linus
asked me to send the whole thing again.
[ Updated the 9p parts as per Al Viro - Linus ]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.org/lkml/2016/1/7/363
Link: https://lkml.org/lkml/2016/5/27/486
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> # For nvmem part
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull block fixes from Jens Axboe:
"A set of fixes that wasn't included in the first merge window pull
request. This pull request contains:
- A set of NVMe fixes from Keith, and one from Nic for the integrity
side of it.
- Fix from Ming, clearing ->mq_ops if we don't successfully setup a
queue for multiqueue.
- A set of stability fixes for bcache from Jiri, and also marking
bcache as orphaned as it's no longer actively maintained (in
mainline, at least)"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: clear q->mq_ops if init fail
MAINTAINERS: mark bcache as orphan
bcache: bch_gc_thread() is not freezable
bcache: bch_allocator_thread() is not freezable
bcache: bch_writeback_thread() is not freezable
nvme/host: Add missing blk_integrity tag_size + flags assignments
NVMe: Add device ID's with stripe quirk
NVMe: Short-cut removal on surprise hot-unplug
NVMe: Allow user initiated rescan
NVMe: Reduce driver log spamming
NVMe: Unbind driver on failure
NVMe: Delete only created queues
NVMe: Allocate queues only for online cpus
|
|
Pull MTD fixes from Brian Norris:
"We've already noticed a few flaws in the MTD work for v4.7-rc1:
- The Atmel folks got ahead of themselves on trying to support their
latest hardware and were working off incorrect documentation. Fix
up the NAND driver to get this correct.
- Fix up device tree example documentation to use the latest
recommendations for describing NAND ECC algorithms"
* tag 'for-linus-20160527' of git://git.infradead.org/linux-mtd:
Documentation: dt: mtd: drop "soft_bch" from example
Revert "mtd: atmel_nand: Support variable RB_EDGE interrupts"
|
|
Pull drm fixes from Dave Airlie:
- one IMX built-in regression fix
- a set of amdgpu fixes, mostly powerplay and polaris GPU stuff
- a set of i915 fixes all over, many cc'ed to stable.
The i915 batch contain support for DP++ dongle detection, which is
used to fix some regressions in the HDMI color depth area
* tag 'drm-fixes-v4.7-rc1' of git://people.freedesktop.org/~airlied/linux: (44 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/imx: Match imx-ipuv3-crtc components using device node in platform data
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
...
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Mostly minor updates and cleanups. One new power management
controller driver for Intel Core SoCs.
platform/x86:
- Add PMC Driver for Intel Core SoC
dell-rbtn:
- Ignore ACPI notifications if device is suspended
thinkpad_acpi:
- save kbdlight state on suspend and restore it on resume
intel_menlow:
- reduce code duplication
asus-wmi:
- provide access to ALS control
ideapad-laptop:
- add a new WMI string for ESC key
surfacepro3_button:
- Add a warning when switching to tablet mode
sony-laptop:
- Avoid oops on module unload for older laptops
intel_telemetry:
- Constify telemetry_core_ops structures
fujitsu-laptop:
- Use IS_ENABLED() instead of checking for built-in or module
asus-laptop:
- correct error handling in sysfs_acpi_set
- remove redundant initializers
- correct error handling in asus_read_brightness()
fujitsu-laptop:
- Support radio LED"
* tag 'platform-drivers-x86-v4.7-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: Add PMC Driver for Intel Core SoC
dell-rbtn: Ignore ACPI notifications if device is suspended
thinkpad_acpi: save kbdlight state on suspend and restore it on resume
intel_menlow: reduce code duplication
asus-wmi: provide access to ALS control
ideapad-laptop: add a new WMI string for ESC key
surfacepro3_button: Add a warning when switching to tablet mode
sony-laptop: Avoid oops on module unload for older laptops
intel_telemetry: Constify telemetry_core_ops structures
fujitsu-laptop: Use IS_ENABLED() instead of checking for built-in or module
asus-laptop: correct error handling in sysfs_acpi_set
asus-laptop: remove redundant initializers
asus-laptop: correct error handling in asus_read_brightness()
fujitsu-laptop: Support radio LED
|
|
Pull intel IOMMU updates from David Woodhouse:
"This patchset improves the scalability of the Intel IOMMU code by
resolving two spinlock bottlenecks and eliminating the linearity of
the IOVA allocator, yielding up to ~5x performance improvement and
approaching 'iommu=off' performance"
* git://git.infradead.org/intel-iommu:
iommu/vt-d: Use per-cpu IOVA caching
iommu/iova: introduce per-cpu caching to iova allocation
iommu/vt-d: change intel-iommu to use IOVA frame numbers
iommu/vt-d: avoid dev iotlb logic for domains with no dev iotlbs
iommu/vt-d: only unmap mapped entries
iommu/vt-d: correct flush_unmaps pfn usage
iommu/vt-d: per-cpu deferred invalidation queues
iommu/vt-d: refactoring of deferred flush entries
|
|
This patch adds the Power Management Controller driver as a PCI driver
for Intel Core SoC architecture.
This driver can utilize debugging capabilities and supported features
as exposed by the Power Management Controller.
Please refer to the below specification for more details on PMC features.
http://www.intel.in/content/www/in/en/chipsets/100-series-chipset-datasheet-vol-2.html
The current version of this driver exposes SLP_S0_RESIDENCY counter.
This counter can be used for detecting fragile SLP_S0 signal related
failures and take corrective actions when PCH SLP_S0 signal is not
asserted after kernel freeze as part of suspend to idle flow
(echo freeze > /sys/power/state).
Intel Platform Controller Hub (PCH) asserts SLP_S0 signal when it
detects favorable conditions to enter its low power mode. As a
pre-requisite the SoC should be in deepest possible Package C-State
and devices should be in low power mode. For example, on Skylake SoC
the deepest Package C-State is Package C10 or PC10. Suspend to idle
flow generally leads to PC10 state but PC10 state may not be sufficient
for realizing the platform wide power potential which SLP_S0 signal
assertion can provide.
SLP_S0 signal is often connected to the Embedded Controller (EC) and the
Power Management IC (PMIC) for other platform power management related
optimizations.
In general, SLP_S0 assertion == PC10 + PCH low power mode + ModPhy Lanes
power gated + PLL Idle.
As part of this driver, a mechanism to read the SLP_S0_RESIDENCY is exposed
as an API and also debugfs features are added to indicate SLP_S0 signal
assertion residency in microseconds.
echo freeze > /sys/power/state
wake the system
cat /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Vishwanath Somayaji <vishwanath.somayaji@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Some BIOSes unconditionally send an ACPI notification to RBTN when the
system is resuming from suspend. This makes dell-rbtn send an input
event to userspace as if a function key was pressed. Prevent this by
ignoring all the notifications received while the device is suspended.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106031
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Override default LED class suspend/resume handles, by keeping track of
the brightness level before suspending so that it can be automatically
restored on resume by calling default resume handler.
Signed-off-by: Marco Trevisan (Treviño) <mail@3v1n0.net>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
aux0_show and aux1_show consists of almost identical code. Pull that
into a common helper and make them thin wrappers. Similarly for
_store.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Asus Zenbook ux31a is providing ACPI0008 interface for ALS
(Ambient Light Sensor), which is accessible for OS => Win 7.
This sensor can be used with iio/acpi-als driver.
Since it is disabled by default, we should use asus-wmi
interface to enable it.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
My patch to the ideapad-laptop driver to get the ESC key working on the
Yoga 1170 (Yoga 3) failed to do the same for the following model, the
Lenovo Yoga 700.
Denis Gordienko managed to get it working by adding another GUID for the
new WMI interface. I have adapted his patch to normal coding style
and simplified it a bit for inclusion, but this patch is currently
untested.
Link: https://forums.lenovo.com/t5/Lenovo-Yoga-Series-Notebooks/YOGA-3-14-How-to-reclaim-my-Esc-key-and-permanently-disable/m-p/3317499
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Denis Gordienko <denis.gordienko.mail@gmail.com>
[dvhart: Whitespace cleanup, static const char *const array declaration]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
Microsoft Surface Book has a tablet mode button. Print another message
once on this event instead of repeating "Unknown event...".
Unfortunately, proper support involves the _DSM method, which is not a
discoverable interface. Just print a warning for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
|
|
I stumbled multiple times over 'return_i2c_dev', especially before the
actual 'return res'. It makes the code hard to read, so reanme the
function to 'put_i2c_dev' which also better matches 'get_free_i2c_dev'.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://anongit.freedesktop.org/drm-intel into drm-next
I see the main drm pull got merged, here's the first batch of fixes for
4.7 already. Fixes all around, a large portion cc: stable stuff.
[airlied: the DP++ stuff is a regression fix].
* tag 'drm-intel-next-fixes-2016-05-25' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Stop automatically retiring requests after a GPU hang
drm/i915: Unify intel_ring_begin()
drm/i915: Ignore stale wm register values on resume on ilk-bdw (v2)
drm/i915/psr: Try to program link training times correctly
drm/i915/bxt: Adjusting the error in horizontal timings retrieval
drm/i915: Don't leave old junk in ilk active watermarks on readout
drm/i915: s/DPPL/DPLL/ for SKL DPLLs
drm/i915: Fix gen8 semaphores id for legacy mode
drm/i915: Set crtc_state->lane_count for HDMI
drm/i915/BXT: Retrieving the horizontal timing for DSI
drm/i915: Protect gen7 irq_seqno_barrier with uncore lock
drm/i915: Re-enable GGTT earlier during resume on pre-gen6 platforms
drm/i915: Determine DP++ type 1 DVI adaptor presence based on VBT
drm/i915: Enable/disable TMDS output buffers in DP++ adaptor as needed
drm/i915: Respect DP++ adaptor TMDS clock limit
drm: Add helper for DP++ adaptors
|
|
into drm-next
AMD GPU bugfixes:
- Various powerplay bug fixes
- Add some new polaris pci ids
- misc bug fixes and code cleanups
* 'drm-next-4.7' of git://people.freedesktop.org/~agd5f/linux: (27 commits)
drm/amd: add Kconfig dependency for ACP on DRM_AMDGPU
drm/amdgpu: Fix hdmi deep color support.
drm/amdgpu: fix bug in fence driver fini
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay/hwmgr: use kmemdup
drm/amd/powerplay: fix bugs of checking if dpm is running on Tonga
drm/amdgpu: update Polaris11 golden setting
drm/amdgpu: Add more Polaris 11 PCI IDs
drm/amdgpu: update Polaris10 golden setting
drm/amdgpu: add more Polaris10 DID
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/amdgpu/cz_dpm: Remove unused variable
drm/amd/amdgpu : Remove unused variable
drm/amd/powerplay: use ARRAY_SIZE() to calculate array size.
drm/amdgpu: fix array out of bounds
drm/radeon: fix array out of bounds
drm/amd/powerplay: fix a bug on updating sclk for Tonga
...
|
|
Merge fixes from Andrew Morton:
"10 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
drivers/pinctrl/intel/pinctrl-baytrail.c: fix build with gcc-4.4
update "mm/zsmalloc: don't fail if can't create debugfs info"
dma-debug: avoid spinlock recursion when disabling dma-debug
mm: oom_reaper: remove some bloat
memcg: fix mem_cgroup_out_of_memory() return value.
ocfs2: fix improper handling of return errno
mm: slub: remove unused virt_to_obj()
mm: kasan: remove unused 'reserved' field from struct kasan_alloc_meta
mm: make CONFIG_DEFERRED_STRUCT_PAGE_INIT depends on !FLATMEM explicitly
seqlock: fix raw_read_seqcount_latch()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull misc DAX updates from Vishal Verma:
"DAX error handling for 4.7
- Until now, dax has been disabled if media errors were found on any
device. This enables the use of DAX in the presence of these
errors by making all sector-aligned zeroing go through the driver.
- The driver (already) has the ability to clear errors on writes that
are sent through the block layer using 'DSMs' defined in ACPI 6.1.
Other misc changes:
- When mounting DAX filesystems, check to make sure the partition is
page aligned. This is a requirement for DAX, and previously, we
allowed such unaligned mounts to succeed, but subsequent
reads/writes would fail.
- Misc/cleanup fixes from Jan that remove unused code from DAX
related to zeroing, writeback, and some size checks"
* tag 'dax-misc-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: fix a comment in dax_zero_page_range and dax_truncate_page
dax: for truncate/hole-punch, do zeroing through the driver if possible
dax: export a low-level __dax_zero_page_range helper
dax: use sb_issue_zerout instead of calling dax_clear_sectors
dax: enable dax in the presence of known media errors (badblocks)
dax: fallback from pmd to pte on error
block: Update blkdev_dax_capable() for consistency
xfs: Add alignment check for DAX mount
ext2: Add alignment check for DAX mount
ext4: Add alignment check for DAX mount
block: Add bdev_dax_supported() for dax mount checks
block: Add vfs_msg() interface
dax: Remove redundant inode size checks
dax: Remove pointless writeback from dax_do_io()
dax: Remove zeroing from dax_io()
dax: Remove dead zeroing code from fault handlers
ext2: Avoid DAX zeroing to corrupt data
ext2: Fix block zeroing in ext2_get_blocks() for DAX
dax: Remove complete_unwritten argument
DAX: move RADIX_DAX_ definitions to dax.c
|
|
gcc-4.4 and thereabouts has issues with initializers of anonymous
unions, and it generates the following warnings:
drivers/pinctrl/intel/pinctrl-baytrail.c:413: error: unknown field 'simple_funcs' specified in initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: missing braces around initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:413: warning: (near initialization for 'byt_score_groups[0].<anonymous>')
drivers/pinctrl/intel/pinctrl-baytrail.c:415: error: unknown field 'simple_funcs' specified in initializer
drivers/pinctrl/intel/pinctrl-baytrail.c:417: error: unknown field 'simple_funcs' specified in initializer
...
Work around this.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"This changeset has a few main parts:
- Ilya has finished a huge refactoring effort to sync up the
client-side logic in libceph with the user-space client code, which
has evolved significantly over the last couple years, with lots of
additional behaviors (e.g., how requests are handled when cluster
is full and transitions from full to non-full).
This structure of the code is more closely aligned with userspace
now such that it will be much easier to maintain going forward when
behavior changes take place. There are some locking improvements
bundled in as well.
- Zheng adds multi-filesystem support (multiple namespaces within the
same Ceph cluster)
- Zheng has changed the readdir offsets and directory enumeration so
that dentry offsets are hash-based and therefore stable across
directory fragmentation events on the MDS.
- Zheng has a smorgasbord of bug fixes across fs/ceph"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (71 commits)
ceph: fix wake_up_session_cb()
ceph: don't use truncate_pagecache() to invalidate read cache
ceph: SetPageError() for writeback pages if writepages fails
ceph: handle interrupted ceph_writepage()
ceph: make ceph_update_writeable_page() uninterruptible
libceph: make ceph_osdc_wait_request() uninterruptible
ceph: handle -EAGAIN returned by ceph_update_writeable_page()
ceph: make fault/page_mkwrite return VM_FAULT_OOM for -ENOMEM
ceph: block non-fatal signals for fault/page_mkwrite
ceph: make logical calculation functions return bool
ceph: tolerate bad i_size for symlink inode
ceph: improve fragtree change detection
ceph: keep leaf frag when updating fragtree
ceph: fix dir_auth check in ceph_fill_dirfrag()
ceph: don't assume frag tree splits in mds reply are sorted
ceph: fix inode reference leak
ceph: using hash value to compose dentry offset
ceph: don't forbid marking directory complete after forward seek
ceph: record 'offset' for each entry of readdir result
ceph: define 'end/complete' in readdir reply as bit flags
...
|
|
Currently 100g devices don't support minimum/maximum BW configurations,
yet link flaps might cause the driver to attempt to do such a
configuration. Prevent this just as we do for the maximum BW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adapter can support 100g in both MSIx and INTa, but not in MSI.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the HW configurations are currently missing for 100g devices.
This can cause various classification issues, as well as prevent device
from fully reaching line-rate.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When DCBx re-negotiation is occurring, the PF's configurations for
maximum and minimum bandwidth guarantees are currently lost.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 39651abd2814 ("qed: add support for dcbx") is re-configuring
the QM hw-block as part of its sequence. This is done in attention
handling context which is non-sleepable, yet memory is allocated in
this flow using GFP_KERNEL.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PFs and VFs differ in their registered ethtool operations,
but they're using a common function for get_sset_count().
As a result, `ethtool -i' for a VF would indicate it supports
selftest, although that's not the case.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since driver is using a FW-based GRO implementation, this has some
effects on its ability to cope with GRO enablement/disablement.
As a result, driver must perform an inner-reload as a result of a state
change in the offload configuration of said feature.
[Failure to do so means network stack would continue to receive
aggregated packets even though user requested the feature to be disabled].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF is currently ignoring the minimum provided by the API,
mistakenly using the maximum for minimum as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i2c-dev had never moved away from the older register_chrdev interface to
implement its char device registration. The register_chrdev API has the
limitation of enabling only up to 256 i2c-dev busses to exist.
Large platforms with lots of i2c devices (i.e. pluggable transceivers)
with dedicated busses may have to exceed that limit.
In particular, there are also platforms making use of the i2c bus
multiplexing API, which instantiates a virtual bus for each possible
multiplexed selection.
This patch removes the register_chrdev usage and replaces it with the
less old cdev API, which takes away the 256 i2c-dev bus limitation.
It should not have any other impact for i2c bus drivers or user space.
This patch has been tested on qemu x86 and qemu powerpc platforms with
the aid of a module which adds and removes 5000 virtual i2c busses, as
well as validated on an existing powerpc hardware platform which makes
use of the i2c bus multiplexing API.
i2c-dev busses with device minor numbers larger than 256 have also been
validated to work with the existing i2c-tools.
Signed-off-by: Erico Nunes <erico.nunes@datacom.ind.br>
[wsa: kept includes sorted]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The ARCH name was changed during the review process of the mach, and
this driver was forgotten to be converted. Fix it now.
http://article.gmane.org/gmane.linux.ports.arm.kernel/456331
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[wsa: updated commit message slightly]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When the DMA configuration fails, there is a log reporting that we can't
use DMA and indicating the error number. When booting the kernel, it is
annoying to see this error number. Moreover, people can think something
is going wrong. It is not the case, it means that DMA can't be used but
it doesn't prevent to use i2c.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If NO_DMA=y:
drivers/built-in.o: In function `rcar_i2c_dma_unmap':
i2c-rcar.c:(.text+0x6f06c6): undefined reference to `bad_dma_ops'
drivers/built-in.o: In function `rcar_i2c_dma':
i2c-rcar.c:(.text+0x6f07e2): undefined reference to `bad_dma_ops'
i2c-rcar.c:(.text+0x6f0838): undefined reference to `bad_dma_ops'
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
New drivers should not use dma_request_slave_channel_reason() but
dma_request_chan(). The former is a macro to the later so this change do
not effect the driver in any way.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This is no longer in use. Remove it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
In practice, each RDMA device has a unique set of counters that the
hardware implements. Having a central set of counters that they must
all adhere to is limiting and causes many useful counters to not be
available.
Therefore we create a dynamic counter registration infrastructure.
The driver must implement a stats structure allocation routine, in
which the driver must place the directory name it wants, a list of
names for all of the counters, an array of u64 counters themselves,
plus a few generic configuration options.
We then implement a core routine to create a sysfs file for each
of the named stats elements, and a core routine to retrieve the
stats when any of the sysfs attribute files are read.
To avoid excessive beating on the stats generation routine in the
drivers, the core code also caches the stats for a short period of
time so that someone attempting to read all of the stats in a
given device's directory will not result in a stats generation
call per file read.
Future work will attempt to standardize just the shared stats
elements, and possibly add a method to get the stats via netlink
in addition to sysfs.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
[ Add caching, make structure names more informative, add i40iw support,
other significant rewrites from the original patch ]
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging
Pull hwmon fixlets from Jean Delvare.
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
Documentation/hwmon: Update links in max34440
hwmon: (emc2103) Fix typo in MODULE_PARM_DESC
|
|
Pull MMC fixes from Ulf Hansson:
"Here are some mmc fixes intended for v4.7 rc1. They are based on a
commit earlier in the merge window and have been tested in linux-next
for a while.
MMC core:
- Prevent re-tuning while serving requests for RPMB partitions
- Extend timeout for long read time quirk to support more eMMCs
MMC host:
- sdhci-acpi: Ensure connected devices are powered when probing
- sdhci-pci|acpi: Remove unreliable MMC_CAP_BUS_WIDTH_TEST for Intel HWs
- dw_mmc: Correct the assigning of max_blk_size
- dw_mmc-rockchip: Allow RPMB partitions to be created
- dw_mmc-rockchip: Set the drive phase properly"
* tag 'mmc-v4.7-rc1' of git://git.linaro.org/people/ulf.hansson/mmc:
mmc: sdhci-acpi: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: sdhci-pci: Remove MMC_CAP_BUS_WIDTH_TEST for Intel controllers
mmc: longer timeout for long read time quirk
mmc: dw_mmc: rockchip: Set the drive phase properly
mmc: dw_mmc: fix the wrong max_blk_size
mmc: dw_mmc-rockchip: add MMC_CAP_CMD23 capabilities
mmc: sdhci-acpi: Ensure connected devices are powered when probing
ACPI / PM: Export acpi_device_fix_up_power()
mmc: block: Pause re-tuning while switched to the RPMB partition
mmc: block: Always switch back to main area after RPMB access
mmc: core: Add a facility to "pause" re-tuning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management updates from Zhang Rui:
- Introduce generic ADC thermal driver, based on OF thermal (Laxman
Dewangan)
- Introduce new thermal driver for Tango chips (Marc Gonzalez)
- Rockchip driver support for RK3399, RK3366, and some fixes (Caesar
Wang, Elaine Zhang and Shawn Lin)
- Add CPU power cooling model to Mediatek thermal driver (Dawei Chien)
- Wider usage of dev_thermal_zone_of_sensor_register (Eduardo Valentin)
- TI thermal driver gained a new maintainer (Keerthy).
- Enabled powerclamp driver by checking CPU feature and package cstate
counter instead of CPU whitelist (Jacob Pan)
- Various fixes on thermal governor, OF thermal, Tegra, and RCAR
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (50 commits)
thermal: tango: initialize TEMPSI_CFG
thermal: rockchip: use the usleep_range instead of udelay
thermal: rockchip: add the notes for better reading
thermal: rockchip: Support RK3366 SoCs in the thermal driver
thermal: rockchip: handle the power sequence for tsadc controller
thermal: rockchip: update the tsadc table for rk3399
thermal: rockchip: fixes the code_to_temp for tsadc driver
thermal: rockchip: disable thermal->clk in err case
thermal: tegra: add Tegra132 specific SOC_THERM driver
thermal: fix ptr_ret.cocci warnings
thermal: mediatek: Add cpu dynamic power cooling model.
thermal: generic-adc: Add ADC based thermal sensor driver
thermal: generic-adc: Add DT binding for ADC based thermal sensor
thermal: tegra: fix static checker warning
thermal: tegra: mark PM functions __maybe_unused
thermal: add temperature sensor support for tango SoC
thermal: hisilicon: fix IRQ imbalance enabling
thermal: hisilicon: support to use any sensor
thermal: rcar: Remove binding docs for r8a7794
thermal: tegra: add PM support
...
|
|
The pio map initialization function is off by 1 causing the last
kernel send context that is allocated to not get mapped into the
pio map which leads to the last kernel send context not being used
by any of the qps.
The send context reserved for VL15 is taken care of by setting the
scontext variable that is used as the index into the kernel send
context array to 1 and does not need to be accounted for in the
kernel send context counting loop as it is currently done.
Fix the kernel send context counting loop to account for all the
allocated send contexts and map all of them to the different VLs.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Two 8051 link settings, external device config and tuning method,
were written in the wrong location and the previous settings were
not cleared. For both, clear the old value and write the new
value.
Fixes: 8ebd4cf1852a ("staging/rdma/hfi1: Add active and optical cable support")
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When FM is disabled, and the HFI port on the switch is
changed from MgmtAllowed=YES to MgmtAllowed=NO and the
link is bounced, FULL_MGMT_P_KEY doesn't get cleared
from the pkey table. This also occurs when the QSFP
cable is moved from a switch port with MgmtAllowed=YES
to a MgmtAllowed=NO port. Clear pkey entry properly.
Also, when the driver is loaded and the switch port is
set to MgmtAllowed=NO, FULL_MGMT_P_KEY shouldn't be added
to pkey table after FM is started. Only set FULL_MGMT_P_KEY
in the pkey table if switch port is configured to
MgmtAllowed=YES.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
rdmavt allows the driver to specify the size of the ack queue, but
only uses it for the modify QP limit testing for setting the atomic
limit value.
The driver dependent size is now used to size the s_ack_queue ring
dynamicially.
Since the driver knows its size, the driver will use its define
for any ring size dependent code.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Commit b9b06cb6feda
("IB/hfi1: Fix missing lock/unlock in verbs drain callback")
added a spin lock.
Unfortunately, the new lock code can be called from a base
level interrupt state, and an interrupt that can get stacked
will attempt to get the same lock.
Fix by using the flag save/restore spin lock variation.
Cc: stable@vger.kernel.org # 4.6+
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
