| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The biggest change to core locking facilities in this cycle is the
introduction of local_lock_t - this primitive comes from the -rt
project and identifies CPU-local locking dependencies normally handled
opaquely beind preempt_disable() or local_irq_save/disable() critical
sections.
The generated code on mainline kernels doesn't change as a result, but
still there are benefits: improved debugging and better documentation
of data structure accesses.
The new local_lock_t primitives are introduced and then utilized in a
couple of kernel subsystems. No change in functionality is intended.
There's also other smaller changes and cleanups"
* tag 'locking-core-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
zram: Use local lock to protect per-CPU data
zram: Allocate struct zcomp_strm as per-CPU memory
connector/cn_proc: Protect send_msg() with a local lock
squashfs: Make use of local lock in multi_cpu decompressor
mm/swap: Use local_lock for protection
radix-tree: Use local_lock for protection
locking: Introduce local_lock()
locking/lockdep: Replace zero-length array with flexible-array
locking/rtmutex: Remove unused rt_mutex_cmpxchg_relaxed()
|
|
clk-next
- Support IDT VersaClock 5P49V5925
- Bunch of updates for HSDK clock generation unit (CGU) driver
- New clk driver for Baikal-T1 SoCs
* clk-vc5:
dt: Add bindings for IDT VersaClock 5P49V5925
clk: vc5: Add support for IDT VersaClock 5P49V6965
* clk-hsdk:
CLK: HSDK: CGU: add support for 148.5MHz clock
CLK: HSDK: CGU: support PLL bypassing
CLK: HSDK: CGU: check if PLL is bypassed first
* clk-mediatek:
clk: mediatek: assign the initial value to clk_init_data of mtk_mux
clk: mediatek: Add MT6765 clock support
clk: mediatek: add mt6765 clock IDs
dt-bindings: clock: mediatek: document clk bindings vcodecsys for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings mipi0a for Mediatek MT6765 SoC
dt-bindings: clock: mediatek: document clk bindings for Mediatek MT6765 SoC
* clk-baikal:
clk: Add Baikal-T1 CCU Dividers driver
clk: Add Baikal-T1 CCU PLLs driver
dt-bindings: clk: Add Baikal-T1 CCU Dividers binding
dt-bindings: clk: Add Baikal-T1 CCU PLLs binding
|
|
'clk-silabs' into clk-next
- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for Qualcomm's MSM8939 Generic Clock Controller
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
* clk-mmp:
clk: mmp2: Add audio clock controller driver
dt-bindings: clock: Add Marvell MMP Audio Clock Controller binding
clk: mmp2: Add support for power islands
dt-bindings: marvell,mmp2: Add ids for the power domains
dt-bindings: clock: Make marvell,mmp2-clock a power controller
clk: mmp2: Add the audio clock
clk: mmp2: Add the I2S clocks
clk: mmp2: Rename mmp2_pll_init() to mmp2_main_clk_init()
clk: mmp2: Move thermal register defines up a bit
dt-bindings: marvell,mmp2: Add clock id for the Audio clock
dt-bindings: marvell,mmp2: Add clock id for the I2S clocks
clk: mmp: frac: Allow setting bits other than the numerator/denominator
clk: mmp: frac: Do not lose last 4 digits of precision
* clk-intel:
clk: intel: remove redundant initialization of variable rate64
clk: intel: Add CGU clock driver for a new SoC
dt-bindings: clk: intel: Add bindings document & header file for CGU
* clk-ingenic:
clk: ingenic: Mark ingenic_tcu_of_match as __maybe_unused
clk: X1000: Add FIXDIV for SSI clock of X1000.
dt-bindings: clock: Add and reorder ABI for X1000.
clk: Ingenic: Add CGU driver for X1830.
dt-bindings: clock: Add X1830 clock bindings.
clk: Ingenic: Adjust cgu code to make it compatible with X1830.
clk: Ingenic: Remove unnecessary spinlock when reading registers.
* clk-qcom:
clk: qcom: Add missing msm8998 ufs_unipro_core_clk_src
dt-bindings: clock: Add YAML schemas for QCOM A53 PLL
clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller
clk: qcom: gcc: Add support for Secure control source clock
dt-bindings: clock: Add gcc_sec_ctrl_clk_src clock ID
clk: qcom: gcc: Add support for a new frequency for SC7180
clk: qcom: Add DT bindings for MSM8939 GCC
clk: qcom: gcc: Add missing UFS clocks for SM8150
clk: qcom: gcc: Add GPU and NPU clocks for SM8150
clk: qcom: mmcc-msm8996: Properly describe GPU_GX gdsc
clk: qcom: gdsc: Handle GDSC regulator supplies
clk: qcom: msm8916: Fix the address location of pll->config_reg
* clk-silabs:
clk: clk-si5341: Add support for the Si5345 series
|
|
'clk-ast2600' into clk-next
* clk-unisoc:
clk: sprd: add mipi_csi_xx gate clocks
clk: sprd: add dt-bindings include for mipi_csi_xx clocks
dt-bindings: clk: sprd: add mipi_csi_xx clocks for SC9863A
clk: sprd: check its parent status before reading gate clock
clk: sprd: return correct type of value for _sprd_pll_recalc_rate
clk: sprd: mark the local clock symbols static
* clk-trivial:
clk: versatile: remove redundant assignment to pointer clk
clk: clk-xgene: Fix a typo in Kconfig
clk: Remove unused inline function clk_debug_reparent
* clk-bcm:
clk: bcm2835: Constify struct debugfs_reg32
clk: bcm2835: Remove casting to bcm2835_clk_register
clk: bcm2835: Fix return type of bcm2835_register_gate
* clk-st:
clk: clk-flexgen: fix clock-critical handling
* clk-ast2600:
clk: ast2600: Fix AHB clock divider for A1
|
|
and 'clk-ti' into clk-next
- Support custom flags in Xilinx zynq firmware
- Various small fixes to the Xilinx clk driver
- Support for Intel Agilex clks
* clk-tegra:
clk: tegra: Add Tegra210 CSI TPG clock gate
clk: tegra30: Use custom CCLK implementation
clk: tegra20: Use custom CCLK implementation
clk: tegra: cclk: Add helpers for handling PLLX rate changes
clk: tegra: pll: Add pre/post rate-change hooks
clk: tegra: Add custom CCLK implementation
clk: tegra: Remove the old emc_mux clock for Tegra210
clk: tegra: Implement Tegra210 EMC clock
clk: tegra: Export functions for EMC clock scaling
clk: tegra: Add PLLP_UD and PLLMB_UD for Tegra210
clk: tegra: Rename Tegra124 EMC clock source file
dt-bindings: clock: tegra: Add clock ID for CSI TPG clock
* clk-imx:
clk: imx: use imx8m_clk_hw_composite_bus for i.MX8M bus clk slice
clk: imx: add imx8m_clk_hw_composite_bus
clk: imx: add mux ops for i.MX8M composite clk
clk: imx8m: migrate A53 clk root to use composite core
clk: imx8mp: use imx8m_clk_hw_composite_core to simplify code
clk: imx8mp: Define gates for pll1/2 fixed dividers
clk: imx: imx8mp: fix pll mux bit
clk: imx8m: drop clk_hw_set_parent for A53
dt-bindings: clocks: imx8mp: Add ids for audiomix clocks
clk: imx: Add helpers for passing the device as argument
clk: imx: pll14xx: Add the device as argument when registering
clk: imx: gate2: Allow single bit gating clock
clk: imx: clk-pllv3: Use readl_relaxed_poll_timeout() for PLL lock wait
clk: imx: clk-sscg-pll: Remove unnecessary blank lines
clk: imx: drop the dependency on ARM64 for i.MX8M
clk: imx7ulp: make it easy to change ARM core clk
clk: imx: imx6ul: change flexcan clock to support CiA bitrates
* clk-zynq:
clk: zynqmp: Make zynqmp_clk_get_max_divisor static
clk: zynqmp: Update fraction clock check from custom type flags
clk: zynqmp: Add support for custom type flags
clk: zynqmp: fix memory leak in zynqmp_register_clocks
clk: zynqmp: Fix invalid clock name queries
clk: zynqmp: Fix divider2 calculation
clk: zynqmp: Limit bestdiv with maxdiv
* clk-socfpga:
clk: socfpga: agilex: add clock driver for the Agilex platform
dt-bindings: documentation: add clock bindings information for Agilex
clk: socfpga: add const to _ops data structures
clk: socfpga: remove clk_ops enable/disable methods
clk: socfpga: stratix10: use new parent data scheme
* clk-at91:
clk: at91: allow setting all PMC clock parents via DT
clk: at91: allow setting PCKx parent via DT
clk: at91: optimize pmc data allocation
clk: at91: pmc: decrement node's refcount
clk: at91: pmc: do not continue if compatible not located
clk: at91: Add peripheral clock for PTC
* clk-ti:
clk: ti: dra7: remove two unused symbols
clk: ti: dra7xx: fix RNG clock parent
clk: ti: dra7xx: mark MCAN clock as DRA76x only
clk: ti: dra7xx: fix gpu clkctrl parent
clk: ti: omap5: Add proper parent clocks for l4-secure clocks
clk: ti: omap4: Add proper parent clocks for l4-secure clocks
clk: ti: composite: fix memory leak
|
|
and 'clk-allwinner' into clk-next
- Allow the COMMON_CLK config to be selectable
* clk-selectable:
clk: Move HAVE_CLK config out of architecture layer
MIPS: Loongson64: Drop asm/clock.h include
ARM: mmp: Remove legacy clk code
clk: Allow the common clk framework to be selectable
mmc: meson-mx-sdio: Depend on OF_ADDRESS and not just OF
MIPS: Remove redundant CLKDEV_LOOKUP selects
h8300: Remove redundant CLKDEV_LOOKUP selects
arm64: tegra: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant COMMON_CLK selects
* clk-amlogic:
clk: meson: meson8b: Don't rely on u-boot to init all GP_PLL registers
clk: meson: meson8b: Make the CCF use the glitch-free VPU mux
clk: meson: meson8b: Fix the vclk_div{1, 2, 4, 6, 12}_en gate bits
clk: meson: meson8b: Fix the polarity of the RESET_N lines
clk: meson: meson8b: Fix the first parent of vid_pll_in_sel
clk: meson: g12a: Prepare the GPU clock tree to change at runtime
clk: meson: gxbb: Prepare the GPU clock tree to change at runtime
clk: meson: meson8b: make the hdmi_sys clock tree mutable
clk: meson8b: export the HDMI system clock
* clk-renesas:
dt-bindings: clock: renesas: mstp: Convert to json-schema
dt-bindings: clock: renesas: div6: Convert to json-schema
clk: renesas: cpg-mssr: Fix STBCR suspend/resume handling
clk: renesas: rcar-gen2: Remove superfluous CLK_RENESAS_DIV6 selects
clk: renesas: cpg-mssr: Add R8A7742 support
dt-bindings: clock: renesas: cpg-mssr: Document r8a7742 binding
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
MAINTAINERS: Add DT Bindings for Renesas Clock Generators
clk: renesas: r9a06g032: Fix some typo in comments
dt-bindings: clock: renesas: rcar-usb2-clock-sel: Add r8a77961 support
* clk-samsung:
clk: samsung: exynos5433: Add IGNORE_UNUSED flag to sclk_i2s1
ARM/SAMSUNG EXYNOS ARM ARCHITECTURES: Use fallthrough;
clk: samsung: Fix CLK_SMMU_FIMCL3 clock name on Exynos542x
clk: samsung: Mark top ISP and CAM clocks on Exynos542x as critical
* clk-allwinner:
clk: sunxi: Fix incorrect usage of round_down()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
"The RCU updates for this cycle were:
- RCU-tasks update, including addition of RCU Tasks Trace for BPF use
and TASKS_RUDE_RCU
- kfree_rcu() updates.
- Remove scheduler locking restriction
- RCU CPU stall warning updates.
- Torture-test updates.
- Miscellaneous fixes and other updates"
* tag 'core-rcu-2020-06-01' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
rcu: Allow for smp_call_function() running callbacks from idle
rcu: Provide rcu_irq_exit_check_preempt()
rcu: Abstract out rcu_irq_enter_check_tick() from rcu_nmi_enter()
rcu: Provide __rcu_is_watching()
rcu: Provide rcu_irq_exit_preempt()
rcu: Make RCU IRQ enter/exit functions rely on in_nmi()
rcu/tree: Mark the idle relevant functions noinstr
x86: Replace ist_enter() with nmi_enter()
x86/mce: Send #MC singal from task work
x86/entry: Get rid of ist_begin/end_non_atomic()
sched,rcu,tracing: Avoid tracing before in_nmi() is correct
sh/ftrace: Move arch_ftrace_nmi_{enter,exit} into nmi exception
lockdep: Always inline lockdep_{off,on}()
hardirq/nmi: Allow nested nmi_enter()
arm64: Prepare arch_nmi_enter() for recursion
printk: Disallow instrumenting print_nmi_enter()
printk: Prepare for nested printk_nmi_enter()
rcutorture: Convert ULONG_CMP_LT() to time_before()
torture: Add a --kasan argument
torture: Save a few lines by using config_override_param initially
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Borislav Petkov:
- Fix i10nm_edac loading on some Ice Lake and Tremont/Jacobsville
steppings due to the offset change of the bus number configuration
register, by Qiuxu Zhuo.
- The usual cleanups and fixes all over the place.
* tag 'edac_updates_for_5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/amd64: Remove redundant assignment to variable ret in hw_info_get()
EDAC/skx: Use the mcmtr register to retrieve close_pg/bank_xor_enable
EDAC/i10nm: Update driver to support different bus number config register offsets
EDAC, {skx,i10nm}: Make some configurations CPU model specific
EDAC/amd8131: Remove defined but not used bridge_str
EDAC/thunderx: Make symbols static
MAINTAINERS: Remove sifive_l2_cache.c from EDAC-SIFIVE pattern
EDAC/xgene: Remove set but not used address local var
EDAC/armada_xp: Fix some log messages
|
|
Newer C compilers are complaining about the fact that there are no
function prototypes in sja1105_vl.c for the non-static functions.
Give them what they want.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Benjamin Herrenschmidt solved a problem with non-matched console
aliases by first checking consoles defined on the command line. It is
a more conservative approach than the previous attempts.
- Benjamin also made sure that the console accessible via /dev/console
always has CON_CONSDEV flag.
- Andy Shevchenko added the %ptT modifier for printing struct time64_t.
It extends the existing %ptR handling for struct rtc_time.
- Bruno Meneguele fixed /dev/kmsg error value returned by unsupported
SEEK_CUR.
- Tetsuo Handa removed unused pr_cont_once().
... and a few small fixes.
* tag 'printk-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: Remove pr_cont_once()
printk: handle blank console arguments passed in.
kernel/printk: add kmsg SEEK_CUR handling
printk: Fix a typo in comment "interator"->"iterator"
usb: pulse8-cec: Switch to use %ptT
ARM: bcm2835: Switch to use %ptT
lib/vsprintf: Print time64_t in human readable format
lib/vsprintf: update comment about simple_strto<foo>() functions
printk: Correctly set CON_CONSDEV even when preferred console was not registered
printk: Fix preferred console selection with multiple matches
printk: Move console matching logic into a separate function
printk: Convert a use of sprintf to snprintf in console_unlock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2020-05-31
This series contains updates to the ice driver only.
Brett modifies the driver to allow users to clear a VF's
administratively set MAC address on the PF. Fixes the driver to
recognize an existing VLAN tag when DMAC/SMAC is enabled in a packet.
Fixes an issue, so that VF's are reset after any VF port VLAN
modifications are made on the PF. Made sure the register QRXFLXP_CNTXT
is cleared before writing a new value to ensure the previous value is
not passed forward. Updates the PF to allow the VF to request a reset
as soon as it has been initialized. Fixes an issue to ensure when a VSI
is created, it uses the current coalesce value, not the default value.
Paul allows untrusted VF's to add 16 filters.
Dan increases the timeout needed after a PFR to allow ample time for
package download.
Chinh adjust the define value for the number of PHY speeds we currently
support. Changes the driver to ignore EMODE error when configuring the
PHY.
Jesse fixes an issue which was preventing a user from configuring the
interface before bringing it up.
Henry fixes the logic for adding back perfect flows after flow director
filter does a deletion.
Bruce fixes line wrappings to make it more consistent.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore updates from Kees Cook:
"Fixes and new features for pstore.
This is a pretty big set of changes (relative to past pstore pulls),
but it has been in -next for a while. The biggest change here is the
ability to support a block device as a pstore backend, which has been
desired for a while. A lot of additional fixes and refactorings are
also included, mostly in support of the new features.
- refactor pstore locking for safer module unloading (Kees Cook)
- remove orphaned records from pstorefs when backend unloaded (Kees
Cook)
- refactor dump_oops parameter into max_reason (Pavel Tatashin)
- introduce pstore/zone for common code for contiguous storage
(WeiXiong Liao)
- introduce pstore/blk for block device backend (WeiXiong Liao)
- introduce mtd backend (WeiXiong Liao)"
* tag 'pstore-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (35 commits)
mtd: Support kmsg dumper based on pstore/blk
pstore/blk: Introduce "best_effort" mode
pstore/blk: Support non-block storage devices
pstore/blk: Provide way to query pstore configuration
pstore/zone: Provide way to skip "broken" zone for MTD devices
Documentation: Add details for pstore/blk
pstore/zone,blk: Add ftrace frontend support
pstore/zone,blk: Add console frontend support
pstore/zone,blk: Add support for pmsg frontend
pstore/blk: Introduce backend for block devices
pstore/zone: Introduce common layer to manage storage zones
ramoops: Add "max-reason" optional field to ramoops DT node
pstore/ram: Introduce max_reason and convert dump_oops
pstore/platform: Pass max_reason to kmesg dump
printk: Introduce kmsg_dump_reason_str()
printk: honor the max_reason field in kmsg_dumper
printk: Collapse shutdown types into a single dump reason
pstore/ftrace: Provide ftrace log merging routine
pstore/ram: Refactor ftrace buffer merging
pstore/ram: Refactor DT size parsing
...
|
|
fix dereference of nexthop group in fdb nexthop group
update validation path.
Fixes: 1274e1cc4226 ("vxlan: ecmp support for mac fdb entries")
Reported-by: Ido Schimmel <idosch@idosch.org>
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Leave congestion group taildrop enabled for all traffic classes
when PFC is enabled. Notification threshold is low enough such
that it will be hit first and this also ensures that FQs on
traffic classes which are not PFC enabled won't drain the buffer
pool.
FQ taildrop threshold is kept disabled as long as any form of
flow control is on. Since FQ taildrop works with bytes, not number
of frames, we can't guarantee it will not interfere with the
congestion notification mechanism for all frame sizes.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support in dpaa2-eth for PFC (Priority Flow Control)
through the DCB ops.
Instruct the hardware to respond to received PFC frames.
Current firmware doesn't allow us to selectively enable PFC
on the Rx side for some priorities only, so we will react to
all incoming PFC frames (and stop transmitting on the traffic
classes specified in the frame).
Also, configure the hardware to generate PFC frames based on Rx
congestion notifications. When a certain number of frames accumulate in
the ingress queues corresponding to a traffic class, priority flow
control frames are generated for that TC.
The number of PFC traffic classes available can be queried through
lldptool. Also, which of those traffic classes have PFC enabled is also
controlled through the same dcbnl_rtnl_ops callbacks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have congestion group taildrop configured at all
times, we can afford to increase the frame queue taildrop
threshold; this will ensure a better response when receiving
bursts of large-sized frames.
Also decouple the buffer pool count from the Rx FQ taildrop
threshold, as above change would increase it too much. Instead,
keep the old count as a hardcoded value.
With the new limits, we try to ensure that:
* we allow enough leeway for large frame bursts (by buffering
enough of them in queues to avoid heavy dropping in case of
bursty traffic, but when overall ingress bandwidth is manageable)
* allow pending frames to be evenly spread between ingress FQs,
regardless of frame size
* avoid dropping frames due to the buffer pool being empty; this
is not a bad behaviour per se, but system overall response is
more linear and predictable when frames are dropped at frame
queue/group level.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The increase in number of ingress frame queues means we now risk
depleting the buffer pool before the FQ taildrop kicks in.
Congestion group taildrop allows us to control the number of frames that
can accumulate on a group of Rx frame queues belonging to the same
traffic class. This setting coexists with the frame queue based
taildrop: whichever limit gets hit first triggers the frame drop.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add convenient helper functions that determines whether Rx/Tx pause
frames are enabled based on link state flags received from firmware.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configure static ingress classification based on VLAN PCP field.
If the DPNI doesn't have enough traffic classes to accommodate all
priority levels, the lowest ones end up on TC 0 (default on miss).
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware reserves for each DPNI a number of RX frame queues
equal to the number of configured flows x number of configured
traffic classes.
Current driver configuration directs all incoming traffic to
FQs corresponding to TC0, leaving all other priority levels unused.
Start adding support for multiple ingress traffic classes, by
configuring the FQs associated with all priority levels, not just
TC0. All settings that are per-TC, such as those related to
hashing and flow steering, are also updated.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't export __bcm_phy_enable_rdb_access() and
__bcm_phy_enable_legacy_access() functions. They aren't used outside this
module and it was forgotten to provide a prototype for these functions.
Just make them static for now.
Fixes: 11ecf8c55b91 ("net: phy: broadcom: add cable test support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tun in IFF_NAPI_FRAGS mode calls napi_gro_frags. Unlike netif_rx and
netif_gro_receive, this expects skb->data to point to the mac layer.
But skb_probe_transport_header, __skb_get_hash_symmetric, and
xdp_do_generic in tun_get_user need skb->data to point to the network
header. Flow dissection also needs skb->protocol set, so
eth_type_trans has to be called.
Ensure the link layer header lies in linear as eth_type_trans pulls
ETH_HLEN. Then take the same code paths for frags as for not frags.
Push the link layer header back just before calling napi_gro_frags.
By pulling up to ETH_HLEN from frag0 into linear, this disables the
frag0 optimization in the special case when IFF_NAPI_FRAGS is used
with zero length iov[0] (and thus empty skb->linear).
Fixes: 90e33d459407 ("tun: enable napi_gro_frags() for TUN/TAP driver")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Petar Penkov <ppenkov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Introduce crypto_shash_tfm_digest() and use it wherever possible.
- Fix use-after-free and race in crypto_spawn_alg.
- Add support for parallel and batch requests to crypto_engine.
Algorithms:
- Update jitter RNG for SP800-90B compliance.
- Always use jitter RNG as seed in drbg.
Drivers:
- Add Arm CryptoCell driver cctrng.
- Add support for SEV-ES to the PSP driver in ccp"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (114 commits)
crypto: hisilicon - fix driver compatibility issue with different versions of devices
crypto: engine - do not requeue in case of fatal error
crypto: cavium/nitrox - Fix a typo in a comment
crypto: hisilicon/qm - change debugfs file name from qm_regs to regs
crypto: hisilicon/qm - add DebugFS for xQC and xQE dump
crypto: hisilicon/zip - add debugfs for Hisilicon ZIP
crypto: hisilicon/hpre - add debugfs for Hisilicon HPRE
crypto: hisilicon/sec2 - add debugfs for Hisilicon SEC
crypto: hisilicon/qm - add debugfs to the QM state machine
crypto: hisilicon/qm - add debugfs for QM
crypto: stm32/crc32 - protect from concurrent accesses
crypto: stm32/crc32 - don't sleep in runtime pm
crypto: stm32/crc32 - fix multi-instance
crypto: stm32/crc32 - fix run-time self test issue.
crypto: stm32/crc32 - fix ext4 chksum BUG_ON()
crypto: hisilicon/zip - Use temporary sqe when doing work
crypto: hisilicon - add device error report through abnormal irq
crypto: hisilicon - remove codes of directly report device errors through MSI
crypto: hisilicon - QM memory management optimization
crypto: hisilicon - unify initial value assignment into QM
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c update from Boris Brezillon:
"Fix GETMRL's logic"
* tag 'i3c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c master: GETMRL's 3rd byte is optional even with BCR_IBI_PAYLOAD
|
|
vmxnet3_get_rss()
The value adapter->rss_conf is stored in DMA memory, and it is assigned
to rssConf, so rssConf->indTableSize can be modified at anytime by
malicious hardware. Because rssConf->indTableSize is assigned to n,
buffer overflow may occur when the code "rssConf->indTable[n]" is
executed.
To fix this possible bug, n is checked after being used.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Microchip lan7431 is frequently connected to a phy. However, it
can also be directly connected to a MII remote peer without
any phy in between. For supporting such a phyless hardware setup
in Linux we utilized phylib, which supports a fixed-link
configuration via the device tree. And we added support for
defining the connection type R/GMII in the device tree.
New behavior:
-------------
. The automatic speed and duplex detection of the lan743x silicon
between mac and phy is disabled. Instead phylib is used like in
other typical Linux drivers. The usage of phylib allows to
specify fixed-link parameters in the device tree.
. The device tree entry phy-connection-type is supported now with
the modes RGMII or (G)MII (default).
Development state:
------------------
. Tested with fixed-phy configurations. Not yet tested in normal
configurations with phy. Microchip kindly offered testing
as soon as the Corona measures allow this.
. All review findings of Andrew Lunn are included
Example:
--------
&pcie {
status = "okay";
host@0 {
reg = <0 0 0 0 0>;
#address-cells = <3>;
#size-cells = <2>;
ethernet@0 {
compatible = "weyland-yutani,noscom1", "microchip,lan743x";
status = "okay";
reg = <0 0 0 0 0>;
phy-connection-type = "rgmii";
fixed-link {
speed = <100>;
full-duplex;
};
};
};
};
Signed-off-by: Roelof Berg <rberg@berg-solutions.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently have an Rx listener function for exception traps that marks
received skbs with 'offload_fwd_mark' and injects them to the kernel's
Rx path. The marking is done because all these exceptions occur during
L3 forwarding, after the packets were potentially flooded at L2.
A subsequent patch will add support for control traps. Packets received
via some of these control traps need different handling:
1. Packets might not need to be marked with 'offload_fwd_mark'. For
example, if packet was trapped before L2 forwarding
2. Packets might not need to be injected to the kernel's Rx path. For
example, sampled packets are reported to user space via the psample
module
Factor out a common Rx listener function that only reports trapped
packets to devlink. Call it from mlxsw_sp_rx_no_mark_listener() and
mlxsw_sp_rx_mark_listener() that will inject the packets to the kernel's
Rx path, without and with the marking, respectively.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register two control traps with devlink. The existing selftest at
tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh iterates
over all registered traps and checks that the action of non-drop traps
cannot be changed. Up until now only exception traps were tested, now
control traps will be tested as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sh5 never became a product and has probably never really worked.
Remove it by recursively deleting all associated Kconfig options
and all corresponding files.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: Liu Xiang <liuxiang_1999@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The removal of mips_swiotlb_ops exposed a problem in octeon_mgmt Ethernet
driver. mips_swiotlb_ops had an mb() after most of the operations and the
removal of the ops had broken the receive functionality of the driver.
My code inspection has shown no other places except
octeon_mgmt_rx_fill_ring() where an explicit barrier would be obviously
missing. The latter function however has to make sure that "ringing the
bell" doesn't happen before RX ring entry is really written.
The patch has been successfully tested on Octeon II.
Fixes: a999933db9ed ("MIPS: remove mips_swiotlb_ops")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The big change in this release is that Matti Vaittinen has factored
out the linear ranges support into a separate library in lib/ since it
is also useful for at least the power subsystem (and most likely
others too), it helps subsystems which need to map register values
into more useful real world values do so with minimal per-driver code.
- Factoring out of the linear ranges support into a library in lib/
from Matti Vaittinen.
- Trace points for bypass mode.
- Use the consumer name in debugfs to make it easier to understand.
- New drivers for Maxim MAX77826 and MAX8998"
* tag 'regulator-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (23 commits)
regulator: max8998: max8998_set_current_limit() can be static
dt-bindings: regulator: Convert anatop regulator to json-schema
regulator: core: Add regulator bypass trace points
regulator: extract voltage balancing code to the separate function
regulator/mfd: max8998: Document charger regulator
regulator: max8998: Add charger regulator
MAINTAINERS: Add maintainer entry for linear ranges helper
regulator: bd718x7: remove voltage change restriction from BD71847 LDOs
lib: linear_ranges: Add missing MODULE_LICENSE()
regulator: use linear_ranges helper
power: supply: bd70528: rename linear_range to avoid collision
lib/test_linear_ranges: add a test for the 'linear_ranges'
lib: add linear ranges helpers
regulator: db8500-prcmu: Use true,false for bool variable
regulator: bd718x7: remove voltage change restriction from BD71847
regulator: max77826: Remove erroneous additionalProperties
regulator: qcom-rpmh: Fix typos in pm8150 and pm8150l
regulator: Document bindings for max77826
regulator: max77826: Add max77826 regulator driver
regulator: tps80031: remove redundant assignment to variables ret and val
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This has been a very active release for the DesignWare driver in
particular - after a long period of inactivity we have had a lot of
people actively working on it for unrelated reasons this cycle with
some of that work still not landed.
Otherwise it's been fairly quiet for the subsystem.
Highlights include:
- Lots of performance improvements and fixes for the DesignWare
driver from Serge Semin, Andy Shevchenko, Wan Ahmad Zainie, Clement
Leger, Dinh Nguyen and Jarkko Nikula.
- Support for octal mode transfers in spidev.
- Slave mode support for the Rockchip drivers.
- Support for AMD controllers, Broadcom mspi and Raspberry Pi 4, and
Intel Elkhart Lake"
* tag 'spi-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (125 commits)
spi: spi-fsl-dspi: fix native data copy
spi: Convert DW SPI binding to DT schema
spi: dw: Refactor mid_spi_dma_setup() to separate DMA and IRQ config
spi: dw: Make DMA request line assignments explicit for Intel Medfield
spi: bcm2835: Remove shared interrupt support
dt-bindings: snps,dw-apb-ssi: add optional reset property
spi: dw: add reset control
spi: bcm2835: Enable shared interrupt support
spi: bcm2835: Implement shutdown callback
spi: dw: Use regset32 DebugFS method to create regdump file
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Fix Rx-only DMA transfers
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
...
|
|
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
No need for mlx5e_rep_indr_clean_block_privs() since flow_block_cb_free()
already releases the internal mapping via ->release callback, which in
this case is mlx5e_rep_indr_tc_block_unbind().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a very active release for the regmap API for some
reason, a lot of it due to new devices with odd requirements that can
sensibly be handled here.
- Add support for buses implementing a custom reg_update_bits()
method in case the bus has a native operation for this.
- Support 16 bit register addresses in SMBus.
- Allow customization of the device attached to regmap-irq.
- Helpers for bitfield operations and per-port field initializations"
* tag 'regmap-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: provide helpers for simple bit operations
regmap: add helper for per-port regfield initialization
regmap-i2c: add 16-bit width registers support
regmap: Simplify implementation of the regmap_field_read_poll_timeout() macro
regmap: Simplify implementation of the regmap_read_poll_timeout() macro
regmap: add reg_sequence helpers
regmap-irq: make it possible to add irq_chip do a specific device node
regmap: Add bus reg_update_bits() support
regmap: debugfs: check count when read regmap file
|
|
Shrink the code visually by replacing regmap_update_bits() with
appropriate regmap bit operations where applicable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Infrastructure:
- Add notification support
New drivers:
- Baikal-T1 PVT sensor driver
- amd_energy driver to report energy counters
- Driver for Maxim MAX16601
- Gateworks System Controller
Various:
- applesmc: avoid overlong udelay()
- dell-smm: Use one DMI match for all XPS models
- ina2xx: Implement alert functions
- lm70: Add support for ACPI
- lm75: Fix coding-style warnings
- lm90: Add max6654 support to lm90 driver
- nct7802: Replace container_of() API
- nct7904: Set default timeout
- nct7904: Add watchdog function
- pmbus: Improve initialization of 'currpage' and 'currphase'"
* tag 'hwmon-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (24 commits)
hwmon: Add Baikal-T1 PVT sensor driver
hwmon: Add notification support
dt-bindings: hwmon: Add Baikal-T1 PVT sensor binding
hwmon: (applesmc) avoid overlong udelay()
hwmon: (nct7904) Set default timeout
hwmon: (amd_energy) Missing platform_driver_unregister() on error in amd_energy_init()
MAINTAINERS: add entry for AMD energy driver
hwmon: (amd_energy) Add documentation
hwmon: Add amd_energy driver to report energy counters
hwmon: (nct7802) Replace container_of() API
hwmon: (lm90) Add max6654 support to lm90 driver
hwmon : (nct6775) Use kobj_to_dev() API
hwmon: (pmbus) Driver for Maxim MAX16601
hwmon: (pmbus) Improve initialization of 'currpage' and 'currphase'
hwmon: (adt7411) update contact email
hwmon: (lm75) Fix all coding-style warnings on lm75 driver
hwmon: Reduce indentation level in __hwmon_device_register()
hwmon: (ina2xx) Implement alert functions
hwmon: (lm70) Add support for ACPI
hwmon: (dell-smm) Use one DMI match for all XPS models
...
|
|
The caller doesn't care about the error codes, they only check for zero
vs non-zero. Still, it's better to preserve the negative error codes
from alloc_uld_rxqs() instead of changing it to 1. We can also return
directly if there is a failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull tpm updates from Jarkko Sakkinen.
* tag 'tpmdd-next-20200522' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: eventlog: Replace zero-length array with flexible-array member
tpm/tpm_ftpm_tee: Use UUID API for exporting the UUID
|
|
When proxy mode is enabled the vxlan device might reply to Neighbor
Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the vxlan device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: 4b29dba9c085 ("vxlan: fix nonfunctional neigh_reduce()")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-06-01
Here's one last bluetooth-next pull request for 5.8, which I hope can
still be accepted.
- Enabled Wide-Band Speech (WBS) support for Qualcomm wcn3991
- Multiple fixes/imprvovements to Qualcomm-based devices
- Fix GAP/SEC/SEM/BI-10-C qualfication test case
- Added support for Broadcom BCM4350C5 device
- Several other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- add, update support and fix few flashes
- prepare BFPT parsing for JESD216 rev D
- kernel doc fixes
|
