| Age | Commit message (Collapse) | Author |
|---|
|
When use cq record db for kernel, it needs to set the hr_cq->db_en
to 1 and configure the dma address of record cq db of qp context.
Fixes: 86188a8810ed ("RDMA/hns: Support cq record doorbell for kernel space")
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Each user_context receives a separate dpi value and thus a different
address on the doorbell bar. The qedr_mmap function needs to validate
the address and map the doorbell bar accordingly.
The current implementation always checked against dpi=0 doorbell range
leading to a wrong mapping for doorbell bar. (It entered an else case
that mapped the address differently). qedr_mmap should only be used
for doorbells, so the else was actually wrong in the first place.
This only has an affect on arm architecture and not an issue on a
x86 based architecture.
This lead to doorbells not occurring on arm based systems and left
applications that use more than one dpi (or several applications
run simultaneously ) to hang.
Fixes: ac1b36e55a51 ("qedr: Add support for user context verbs")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
spin_lock/unlock was used instead of spin_un/lock_irq
in a procedure used in process space, on a spinlock
which can be grabbed in an interrupt.
This caused the stack trace below to be displayed (on kernel
4.17.0-rc1 compiled with Lock Debugging enabled):
[ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
[ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G I
[ 154.675856] -----------------------------------------------------
[ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core]
[ 154.700927]
and this task is already holding:
[ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib]
[ 154.718028] which would create a new lock dependency:
[ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.}
[ 154.731922]
but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 154.740798] (&(&cq->lock)->rlock){..-.}
[ 154.740800]
... which became SOFTIRQ-irq-safe at:
[ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50
[ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib]
[ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib]
...
to a SOFTIRQ-irq-unsafe lock:
[ 154.815603] (&(&qp_table->lock)->rlock){+.+.}
[ 154.815604]
... which became SOFTIRQ-irq-unsafe at:
[ 154.827718] ...
[ 154.827720] _raw_spin_lock+0x35/0x50
[ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core]
[ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core]
Since mlx4_qp_lookup() is called only in process space, we can
simply replace the spin_un/lock calls with spin_un/lock_irq calls.
Fixes: 6dc06c08bef1 ("net/mlx4: Fix the check in attaching steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BayTrail-based and newer Chromebooks describe their peripherals in ACPI;
unfortunately their description is not complete, and peripherals
drivers, such as driver for Atmel Touch controllers, has to resort to
DMI-matching to configure the peripherals properly. To avoid polluting
peripheral driver code, let's teach chromeos_laptop driver to supply
missing data via generic device properties.
Note we supply "compatible" string for Atmel peripherals not because it is
needed for matching devices and driver (matching is still done on ACPI HID
entries), but because peripherals driver will be using presence of
"compatible" property to determine if device properties have been attached
to the device, and fail to bind if they are absent.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).
This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.
Fixes: 5b4e29005123 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in mlx4_dbg debug message and also
change the phrasing of the message so that is is more readable
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When enabling the sub-CRQ IRQ a previous update sent a H_EOI prior
to the enablement to clear any pending interrupts that may be present
across a partition migration. This fixed a firmware bug where a
migration could erroneously indicate that a H_EOI was pending.
The H_EOI should only be sent when enabling during a mobility
event though. Doing so at other time could wrong and can produce
extra driver output when IRQs are enabled when doing TX completion.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New ICs (like the one on the Lenovo T480s) answer to
ETP_SMBUS_IAP_VERSION_CMD 4 bytes instead of 3. This corrupts the stack
as i2c_smbus_read_block_data() uses the values returned by the i2c
device to know how many data it need to return.
i2c_smbus_read_block_data() can read up to 32 bytes (I2C_SMBUS_BLOCK_MAX)
and there is no safeguard on how many bytes are provided in the return
value. Ensure we always have enough space for any future firmware.
Also 0-initialize the values to prevent any access to uninitialized memory.
Cc: <stable@vger.kernel.org> # v4.4.x, v4.9.x, v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This time, Lenovo decided to go with different pieces in its latest
series of Thinkpads.
For those we have been able to test:
- the T480 is using Synaptics with an IBM trackpoint
-> it behaves properly with or without intertouch, there is no point
not using RMI4
- the X1 Carbon 6th gen is using Synaptics with an IBM trackpoint
-> the touchpad doesn't behave properly under PS/2 so we have to
switch it to RMI4 if we do not want to have disappointed users
- the X280 is using Synaptics with an ALPS trackpoint
-> the recent fixes in the trackpoint handling fixed it so upstream
now works fine with or without RMI4, and there is no point not
using RMI4
- the T480s is using an Elan touchpad, so that's a different story
Cc: <stable@vger.kernel.org> # v4.14.x, v4.15.x, v4.16.x
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: KT Liao <kt.liao@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Synaptics devices reported it has Intertouch support,
and it fails via PS/2 as following logs:
psmouse serio2: Failed to reset mouse on synaptics-pt/serio0
psmouse serio2: Failed to enable mouse on synaptics-pt/serio0
Set these new devices to use SMBus to fix this issue, then they report
SMBus version 3 is using, patch:
https://patchwork.kernel.org/patch/9989547/ enabled SMBus ver 3 and
makes synaptics devices work fine on SMBus mode.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
trackpoints should use RMI
Lenovo use two different trackpoints in the fifth generation Thinkpad X1
Carbon. Both are accessible over SMBUS/RMI but the pnpIDs are missing.
This patch is for the Elantech trackpoint specifically which also
reports SMB version 3 so rmi_smbus needs to be updated in order to
handle it.
For the record, I was not the first one to come up with this patch as it
has been floating around the internet for a while now. However, I have
spent significant time with testing and my efforts to find the original
author of the patch have been unsuccessful.
Signed-off-by: Edvard Holst <edvard.holst@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.17
Hopefully the last fixes for 4.17. ssb is again causing problems so we
had to revert a commit and fix it better. Also a small fix to bcma and
some MAINTAINERS file updates.
ssb
* fix regression with all module PCI cards, for example using b43 and
b44 drivers
* try again fixing a MIPS linker error
bcma
* fix truncated info log messages
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The touchpad on Lenovo Carbon X1 Gen 5 (2017 - Kabylake) is accessible over
SMBUS/RMI, so let's activate it by default.
Cc: stable@vger.kernel.org
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When link is down, writes to the device might fail with
-EIO. Userspace needs an indication when the status is resolved. As a
fix, tun_net_open() attempts to wake up writers - but that is only
effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is
not the case of vhost_net which only poll for EPOLLOUT after it meets
errors during sendmsg().
This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when
socket is not writable or device is down to guarantee EPOLLOUT will be
raised in either tun_chr_poll() or tun_sock_write_space() after device
is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 1bd4978a88ac2 ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to drop refcnt to xdp_page if we see a gso packet. Otherwise
it will be leaked. Fixing this by moving the check of gso packet above
the linearizing logic. While at it, remove useless comment as well.
Cc: John Fastabend <john.fastabend@gmail.com>
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we successfully linearize the packet, num_buf will be set to zero
which may confuse error handling path which assumes num_buf is at
least 1 and this can lead the code tries to pop the descriptor of next
buffer. Fixing this by checking num_buf against 1 before decreasing.
Fixes: 4941d472bf95 ("virtio-net: do not reset during XDP set")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should not go for the error path after successfully transmitting a
XDP buffer after linearizing. Since the error path may try to pop and
drop next packet and increase the drop counters. Fixing this by simply
drop the refcnt of original page and go for xmit path.
Fixes: 72979a6c3590 ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After a linearized packet was redirected by XDP, we should not go for
the err path which will try to pop buffers for the next packet and
increase the drop counter. Fixing this by just drop the page refcnt
for the original page.
Fixes: 186b3c998c50 ("virtio-net: support XDP_REDIRECT")
Reported-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* hwsim radio dump wasn't working for the first radio
* mesh was updating statistics incorrectly
* a netlink message allocation was possibly too short
* wiphy name limit was still too long
* in certain cases regdb query could find a NULL pointer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fix from Lee Jones:
"A single cros_ec_spi fix correcting the handling for long-running
commands"
* tag 'mfd-fixes-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: cros_ec: Retry commands when EC is known to be busy
|
|
We have had problems displaying fbdev after a resume and as a
workaround we have had to call vmw_fb_refresh(). This has had
a number of unwanted side-effects. The root of the problem was,
however that the coalesced fbdev dirty region was not empty on
the first dirty_mark() after a resume, so a flush was never
scheduled.
Fix this by force scheduling an fbdev flush after resume, and
remove the workaround.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
|
|
The error paths were leaking opened channels.
Fix by using dedicated error paths.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
Depending on whether the kernel is compiled with frame-pointer or not,
the temporary memory location used for the bp parameter in these macros
is referenced relative to the stack pointer or the frame pointer.
Hence we can never reference that parameter when we've modified either
the stack pointer or the frame pointer, because then the compiler would
generate an incorrect stack reference.
Fix this by pushing the temporary memory parameter on a known location on
the stack before modifying the stack- and frame pointers.
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
|
|
Dasd uses completion_data from struct request to store per request
private data - this is problematic since this member is part of a
union which is also used by IO schedulers.
Let the block layer maintain space for per request data behind each
struct request.
Fixes crashes on block layer timeouts like this one:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0000000000000000 TEID: 0000000000000483
Fault in home space mode while using kernel ASCE.
AS:0000000001308007 R3:00000000fffc8007 S:00000000fffcc000 P:000000000000013d
Oops: 0004 ilc:2 [#1] PREEMPT SMP
Modules linked in: [...]
CPU: 0 PID: 1480 Comm: kworker/0:2H Not tainted 4.17.0-rc4-00046-gaa3bcd43b5af #203
Hardware name: IBM 3906 M02 702 (LPAR)
Workqueue: kblockd blk_mq_timeout_work
Krnl PSW : 0000000067ac406b 00000000b6960308 (do_raw_spin_trylock+0x30/0x78)
R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:2 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000c00 0000000000000000 0000000000000000 0000000000000001
0000000000b9d3c8 0000000000000000 0000000000000001 00000000cf9639d8
0000000000000000 0700000000000000 0000000000000000 000000000099f09e
0000000000000000 000000000076e9d0 000000006247bb08 000000006247bae0
Krnl Code: 00000000001c159c: b90400c2 lgr %r12,%r2
00000000001c15a0: a7180000 lhi %r1,0
#00000000001c15a4: 583003a4 l %r3,932
>00000000001c15a8: ba132000 cs %r1,%r3,0(%r2)
00000000001c15ac: a7180001 lhi %r1,1
00000000001c15b0: a784000b brc 8,1c15c6
00000000001c15b4: c0e5004e72aa brasl %r14,b8fb08
00000000001c15ba: 1812 lr %r1,%r2
Call Trace:
([<0700000000000000>] 0x700000000000000)
[<0000000000b9d3d2>] _raw_spin_lock_irqsave+0x7a/0xb8
[<000000000099f09e>] dasd_times_out+0x46/0x278
[<000000000076ea6e>] blk_mq_terminate_expired+0x9e/0x108
[<000000000077497a>] bt_for_each+0x102/0x130
[<0000000000774e54>] blk_mq_queue_tag_busy_iter+0x74/0xd8
[<000000000076fea0>] blk_mq_timeout_work+0x260/0x320
[<0000000000169dd4>] process_one_work+0x3bc/0x708
[<000000000016a382>] worker_thread+0x262/0x408
[<00000000001723a8>] kthread+0x160/0x178
[<0000000000b9e73a>] kernel_thread_starter+0x6/0xc
[<0000000000b9e734>] kernel_thread_starter+0x0/0xc
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<0000000000b9d3cc>] _raw_spin_lock_irqsave+0x74/0xb8
Kernel panic - not syncing: Fatal exception: panic_on_oops
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Reviewed-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Commit 001dde9400d5 ("mfd: cros ec: spi: Fix "in progress" error
signaling") pointed out some bad code, but its analysis and conclusion
was not 100% correct.
It *is* correct that we should not propagate result==EC_RES_IN_PROGRESS
for transport errors, because this has a special meaning -- that we
should follow up with EC_CMD_GET_COMMS_STATUS until the EC is no longer
busy. This is definitely the wrong thing for many commands, because
among other problems, EC_CMD_GET_COMMS_STATUS doesn't actually retrieve
any RX data from the EC, so commands that expected some data back will
instead start processing junk.
For such commands, the right answer is to either propagate the error
(and return that error to the caller) or resend the original command
(*not* EC_CMD_GET_COMMS_STATUS).
Unfortunately, commit 001dde9400d5 forgets a crucial point: that for
some long-running operations, the EC physically cannot respond to
commands any more. For example, with EC_CMD_FLASH_ERASE, the EC may be
re-flashing its own code regions, so it can't respond to SPI interrupts.
Instead, the EC prepares us ahead of time for being busy for a "long"
time, and fills its hardware buffer with EC_SPI_PAST_END. Thus, we
expect to see several "transport" errors (or, messages filled with
EC_SPI_PAST_END). So we should really translate that to a retryable
error (-EAGAIN) and continue sending EC_CMD_GET_COMMS_STATUS until we
get a ready status.
IOW, it is actually important to treat some of these "junk" values as
retryable errors.
Together with commit 001dde9400d5, this resolves bugs like the
following:
1. EC_CMD_FLASH_ERASE now works again (with commit 001dde9400d5, we
would abort the first time we saw EC_SPI_PAST_END)
2. Before commit 001dde9400d5, transport errors (e.g.,
EC_SPI_RX_BAD_DATA) seen in other commands (e.g.,
EC_CMD_RTC_GET_VALUE) used to yield junk data in the RX buffer; they
will now yield -EAGAIN return values, and tools like 'hwclock' will
simply fail instead of retrieving and re-programming undefined time
values
Fixes: 001dde9400d5 ("mfd: cros ec: spi: Fix "in progress" error signaling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Make sure to invoke pci_disable_device() when errors occur in
pcnet32_probe_pci().
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8d9 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In divasmain.c, the function divas_write() firstly invokes the function
diva_xdi_open_adapter() to open the adapter that matches with the adapter
number provided by the user, and then invokes the function diva_xdi_write()
to perform the write operation using the matched adapter. The two functions
diva_xdi_open_adapter() and diva_xdi_write() are located in diva.c.
In diva_xdi_open_adapter(), the user command is copied to the object 'msg'
from the userspace pointer 'src' through the function pointer 'cp_fn',
which eventually calls copy_from_user() to do the copy. Then, the adapter
number 'msg.adapter' is used to find out a matched adapter from the
'adapter_queue'. A matched adapter will be returned if it is found.
Otherwise, NULL is returned to indicate the failure of the verification on
the adapter number.
As mentioned above, if a matched adapter is returned, the function
diva_xdi_write() is invoked to perform the write operation. In this
function, the user command is copied once again from the userspace pointer
'src', which is the same as the 'src' pointer in diva_xdi_open_adapter() as
both of them are from the 'buf' pointer in divas_write(). Similarly, the
copy is achieved through the function pointer 'cp_fn', which finally calls
copy_from_user(). After the successful copy, the corresponding command
processing handler of the matched adapter is invoked to perform the write
operation.
It is obvious that there are two copies here from userspace, one is in
diva_xdi_open_adapter(), and one is in diva_xdi_write(). Plus, both of
these two copies share the same source userspace pointer, i.e., the 'buf'
pointer in divas_write(). Given that a malicious userspace process can race
to change the content pointed by the 'buf' pointer, this can pose potential
security issues. For example, in the first copy, the user provides a valid
adapter number to pass the verification process and a valid adapter can be
found. Then the user can modify the adapter number to an invalid number.
This way, the user can bypass the verification process of the adapter
number and inject inconsistent data.
This patch reuses the data copied in
diva_xdi_open_adapter() and passes it to diva_xdi_write(). This way, the
above issues can be avoided.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently there is no license information in the header of
this file.
The MODULE_LICENSE field contains ("GPL"), which means
GNU Public License v2 or later, so add a corresponding
SPDX license identifier.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 08810a4119aa (PM / core: Add NEVER_SKIP and SMART_PREPARE
driver flags) inadvertently prevented the power.direct_complete flag
from being set for devices without PM callbacks and with disabled
runtime PM which also prevents power.direct_complete from being set
for their parents. That led to problems including a resume crash on
HP ZBook 14u.
Restore the previous behavior by causing power.direct_complete to be
set for those devices again, but do that in a more direct way to
avoid overlooking that case in the future.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199693
Fixes: 08810a4119aa (PM / core: Add NEVER_SKIP and SMART_PREPARE driver flags)
Reported-by: Thomas Martitz <kugel@rockbox.org>
Tested-by: Thomas Martitz <kugel@rockbox.org>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
|
|
Since 6335698e24ec11e1324b916177da6721df724dd8 the radio with idx of 0
will not get dumped in HWSIM_CMD_GET_RADIO because of the last_idx
checks. Offset cb->args[0] by 1 similarly to what is done in nl80211.c.
Fixes: 6335698e24ec ("mac80211_hwsim: add generation count for netlink dump operation")
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Single regression fix for rcar-du lvds
* 'drm/du/fixes' of git://linuxtv.org/pinchartl/media:
drm: rcar-du: lvds: Fix crash in .atomic_check when disabling connector
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two driver fixes (zfcp and target core), one information leak in sg
and one build clean up"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: allocate with __GFP_ZERO in sg_build_indirect()
scsi: core: clean up generated file scsi_devinfo_tbl.c
scsi: target: tcmu: fix error resetting qfull_time_out to default
scsi: zfcp: fix infinite iteration on ERP ready list
|
|
When a loop block device encounters a writeback error, that error will
get propagated to the bd_inode's wb_err field. If we then detach the
backing file from it, attach another and fsync it, we'll get back the
writeback error that we had from the previous backing file.
This is a bit of a grey area as POSIX doesn't cover loop devices, but it
is somewhat counterintuitive.
If we detach a backing file from the loopdev while there are still
unreported errors, take it as a sign that we're no longer interested in
the previous file, and clear out the wb_err in the loop blockdev.
Reported-and-Tested-by: Theodore Y. Ts'o <tytso@mit.edu>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Merge speculative store buffer bypass fixes from Thomas Gleixner:
- rework of the SPEC_CTRL MSR management to accomodate the new fancy
SSBD (Speculative Store Bypass Disable) bit handling.
- the CPU bug and sysfs infrastructure for the exciting new Speculative
Store Bypass 'feature'.
- support for disabling SSB via LS_CFG MSR on AMD CPUs including
Hyperthread synchronization on ZEN.
- PRCTL support for dynamic runtime control of SSB
- SECCOMP integration to automatically disable SSB for sandboxed
processes with a filter flag for opt-out.
- KVM integration to allow guests fiddling with SSBD including the new
software MSR VIRT_SPEC_CTRL to handle the LS_CFG based oddities on
AMD.
- BPF protection against SSB
.. this is just the core and x86 side, other architecture support will
come separately.
* 'speck-v20' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (49 commits)
bpf: Prevent memory disambiguation attack
x86/bugs: Rename SSBD_NO to SSB_NO
KVM: SVM: Implement VIRT_SPEC_CTRL support for SSBD
x86/speculation, KVM: Implement support for VIRT_SPEC_CTRL/LS_CFG
x86/bugs: Rework spec_ctrl base and mask logic
x86/bugs: Remove x86_spec_ctrl_set()
x86/bugs: Expose x86_spec_ctrl_base directly
x86/bugs: Unify x86_spec_ctrl_{set_guest,restore_host}
x86/speculation: Rework speculative_store_bypass_update()
x86/speculation: Add virtualized speculative store bypass disable support
x86/bugs, KVM: Extend speculation control for VIRT_SPEC_CTRL
x86/speculation: Handle HT correctly on AMD
x86/cpufeatures: Add FEATURE_ZEN
x86/cpufeatures: Disentangle SSBD enumeration
x86/cpufeatures: Disentangle MSR_SPEC_CTRL enumeration from IBRS
x86/speculation: Use synthetic bits for IBRS/IBPB/STIBP
KVM: SVM: Move spec control call after restore of GS
x86/cpu: Make alternative_msr_write work for 32-bit code
x86/bugs: Fix the parameters alignment and missing void
x86/bugs: Make cpu_show_common() static
...
|
|
We're casting the CDROM layer request_sense to the SCSI sense
buffer, but the former is 64 bytes and the latter is 96 bytes.
As we generally allocate these on the stack, we end up blowing
up the stack.
Fix this by wrapping the scsi_execute() call with a properly
sized sense buffer, and copying back the bits for the CDROM
layer.
Cc: stable@vger.kernel.org
Reported-by: Piotr Gabriel Kosinski <pg.kosinski@gmail.com>
Reported-by: Daniel Shapira <daniel@twistlock.com>
Tested-by: Kees Cook <keescook@chromium.org>
Fixes: 82ed4db499b8 ("block: split scsi_request out of struct request")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull networking fixes from David Miller:
1) Fix refcounting bug for connections in on-packet scheduling mode of
IPVS, from Julian Anastasov.
2) Set network header properly in AF_PACKET's packet_snd, from Willem
de Bruijn.
3) Fix regressions in 3c59x by converting to generic DMA API. It was
relying upon the hack that the PCI DMA interfaces would accept NULL
for EISA devices. From Christoph Hellwig.
4) Remove RDMA devices before unregistering netdev in QEDE driver, from
Michal Kalderon.
5) Use after free in TUN driver ptr_ring usage, from Jason Wang.
6) Properly check for missing netlink attributes in SMC_PNETID
requests, from Eric Biggers.
7) Set DMA mask before performaing any DMA operations in vmxnet3
driver, from Regis Duchesne.
8) Fix mlx5 build with SMP=n, from Saeed Mahameed.
9) Classifier fixes in bcm_sf2 driver from Florian Fainelli.
10) Tuntap use after free during release, from Jason Wang.
11) Don't use stack memory in scatterlists in tls code, from Matt
Mullins.
12) Not fully initialized flow key object in ipv4 routing code, from
David Ahern.
13) Various packet headroom bug fixes in ip6_gre driver, from Petr
Machata.
14) Remove queues from XPS maps using correct index, from Amritha
Nambiar.
15) Fix use after free in sock_diag, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (64 commits)
net: ip6_gre: fix tunnel metadata device sharing.
cxgb4: fix offset in collecting TX rate limit info
net: sched: red: avoid hashing NULL child
sock_diag: fix use-after-free read in __sk_free
sh_eth: Change platform check to CONFIG_ARCH_RENESAS
net: dsa: Do not register devlink for unused ports
net: Fix a bug in removing queues from XPS map
bpf: fix truncated jump targets on heavy expansions
bpf: parse and verdict prog attach may race with bpf map update
bpf: sockmap update rollback on error can incorrectly dec prog refcnt
net: test tailroom before appending to linear skb
net: ip6_gre: Fix ip6erspan hlen calculation
net: ip6_gre: Split up ip6gre_changelink()
net: ip6_gre: Split up ip6gre_newlink()
net: ip6_gre: Split up ip6gre_tnl_change()
net: ip6_gre: Split up ip6gre_tnl_link_config()
net: ip6_gre: Fix headroom request in ip6erspan_tunnel_xmit()
net: ip6_gre: Request headroom in __gre6_xmit()
selftests/bpf: check return value of fopen in test_verifier.c
erspan: fix invalid erspan version.
...
|
|
While whitelisting Micron M500DC drives, the tweaked blacklist entry
enabled queued TRIM from M500IT variants also. But these do not support
queued TRIM. And while using those SSDs with the latest kernel we have
seen errors and even the partition table getting corrupted.
Some part from the dmesg:
[ 6.727384] ata1.00: ATA-9: Micron_M500IT_MTFDDAK060MBD, MU01, max UDMA/133
[ 6.727390] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 6.741026] ata1.00: supports DRM functions and may not be fully accessible
[ 6.759887] ata1.00: configured for UDMA/133
[ 6.762256] scsi 0:0:0:0: Direct-Access ATA Micron_M500IT_MT MU01 PQ: 0 ANSI: 5
and then for the error:
[ 120.860334] ata1.00: exception Emask 0x1 SAct 0x7ffc0007 SErr 0x0 action 0x6 frozen
[ 120.860338] ata1.00: irq_stat 0x40000008
[ 120.860342] ata1.00: failed command: SEND FPDMA QUEUED
[ 120.860351] ata1.00: cmd 64/01:00:00:00:00/00:00:00:00:00/a0 tag 0 ncq dma 512 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout)
[ 120.860353] ata1.00: status: { DRDY }
[ 120.860543] ata1: hard resetting link
[ 121.166128] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 121.166376] ata1.00: supports DRM functions and may not be fully accessible
[ 121.186238] ata1.00: supports DRM functions and may not be fully accessible
[ 121.204445] ata1.00: configured for UDMA/133
[ 121.204454] ata1.00: device reported invalid CHS sector 0
[ 121.204541] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[ 121.204546] sd 0:0:0:0: [sda] tag#18 Sense Key : 0x5 [current]
[ 121.204550] sd 0:0:0:0: [sda] tag#18 ASC=0x21 ASCQ=0x4
[ 121.204555] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x93 93 08 00 00 00 00 00 04 28 80 00 00 00 30 00 00
[ 121.204559] print_req_error: I/O error, dev sda, sector 272512
After few reboots with these errors, and the SSD is corrupted.
After blacklisting it, the errors are not seen and the SSD does not get
corrupted any more.
Fixes: 243918be6393 ("libata: Do not blacklist Micron M500DC")
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The SDHCI_QUIRK2_HOST_OFF_CARD_ON is needed for the driver to
properly reset the host controller (reset all) on initialization
after exiting deep sleep.
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Fixes: c833e92bbb60 ("mmc: sdhci-iproc: support standard byte register accesses")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.
Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Remove hard coded mmc cap 1.8v from platform data as it is board specific.
The 1.8v DDR mmc caps can be enabled using DTS property for those
boards that support it.
Fixes: b17b4ab8ce38 ("mmc: sdhci-iproc: define MMC caps in platform data")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In commit 97548575bef3 ("mmc: block: Convert RPMB to a character device") a
new function `mmc_rpmb_ioctl` was added. The final return is simply
returning a value of `0` instead of propagating the correct return code.
Discovered during a compilation with W=1, silence the following gcc warning
drivers/mmc/core/block.c:2470:6: warning: variable ‘ret’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Fixes: 97548575bef3 ("mmc: block: Convert RPMB to a character device")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc fixlets from Helge Deller:
"Three small section mismatch fixes, one of them was found by 0-day
test infrastructure"
* 'parisc-4.17-5' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Move ccio_cujo20_fixup() into init section
parisc: Move setup_profiling_timer() out of init section
parisc: Move find_pa_parent_type() out of init section
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
- Use explicitely sized type for the romimage pointer in the 32bit EFI
protocol struct so a 64bit kernel does not expand it to 64bit. Ditto
for the 64bit struct to avoid the reverse issue on 32bit kernels.
- Handle randomized tex offset correctly in the ARM64 EFI stub to avoid
unaligned data resulting in stack corruption and other hard to
diagnose wreckage.
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/libstub/arm64: Handle randomized TEXT_OFFSET
efi: Avoid potential crashes, fix the 'struct efi_pci_io_protocol_32' definition for mixed mode
|
|
The connector .atomic_check() handler can be called with a NULL crtc
pointer in the connector state when the connector gets disabled
explicitly (through performing a legacy mode set or setting the
connector's CRTC_ID property to 0). This causes a crash as the crtc
pointer is dereferenced without any check.
Fix it by returning from the .atomic_check() handler when then crtc
pointer is NULL, as there is no check to be performed when the connector
gets disabled.
Fixes: c6a27fa41fab ("drm: rcar-du: Convert LVDS encoder code to bridge driver")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A handful of fixes. I've been queuing them up a bit too long so the
list is longer than it otherwise would have been spread out across a
few -rcs.
In general, it's a scattering of fixes across several platforms,
nothing truly serious enough to point out.
There's a slightly larger batch of them for the Davinci platforms due
to work to bring them back to life after some time, so there's a
handful of regressions, some of them going back very far, others more
recent.
There's also a few patches fixing DT on Renesas platforms since they
changed some bindings without remaining backwards compatible,
splitting up describing LVDS as a proper bridge instead of having it
as part of the display unit.
We could push for them to be backwards compatible with old device
trees, but it's likely to regress eventually if nobody's actually
using said compatibility"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (36 commits)
ARM: davinci: board-dm646x-evm: set VPIF capture card name
ARM: davinci: board-dm646x-evm: pass correct I2C adapter id for VPIF
ARM: davinci: dm646x: fix timer interrupt generation
ARM: keystone: fix platform_domain_notifier array overrun
arm64: dts: exynos: Fix interrupt type for I2S1 device on Exynos5433
ARM: dts: imx51-zii-rdu1: fix touchscreen bindings
firmware: arm_scmi: Use after free in scmi_create_protocol_device()
ARM: dts: cygnus: fix irq type for arm global timer
Revert "ARM: dts: logicpd-som-lv: Fix pinmux controller references"
tee: check shm references are consistent in offset/size
tee: shm: fix use-after-free via temporarily dropped reference
ARM: dts: imx7s: Pass the 'fsl,sec-era' property
ARM: dts: tegra20: Revert "Fix ULPI regression on Tegra20"
ARM: dts: correct missing "compatible" entry for ti81xx SoCs
ARM: OMAP1: ams-delta: fix deferred_fiq handler
arm64: tegra: Make BCM89610 PHY interrupt as active low
ARM: davinci: fix GPIO lookup for I2C
ARM: dts: logicpd-som-lv: Fix pinmux controller references
ARM: dts: logicpd-som-lv: Fix Audio Mute
ARM: dts: logicpd-som-lv: Fix WL127x Startup Issues
...
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fix from Vinod Koul:
- qcom bam runtime_pm fix
- email update for Vinod
* tag 'dmaengine-fix-4.17-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: qcom: bam_dma: check if the runtime pm enabled
dmaengine: Update email address for Vinod
|
|
When CONFIG_RANDOMIZE_TEXT_OFFSET=y, TEXT_OFFSET is an arbitrary
multiple of PAGE_SIZE in the interval [0, 2MB).
The EFI stub does not account for the potential misalignment of
TEXT_OFFSET relative to EFI_KIMG_ALIGN, and produces a randomized
physical offset which is always a round multiple of EFI_KIMG_ALIGN.
This may result in statically allocated objects whose alignment exceeds
PAGE_SIZE to appear misaligned in memory. This has been observed to
result in spurious stack overflow reports and failure to make use of
the IRQ stacks, and theoretically could result in a number of other
issues.
We can OR in the low bits of TEXT_OFFSET to ensure that we have the
necessary offset (and hence preserve the misalignment of TEXT_OFFSET
relative to EFI_KIMG_ALIGN), so let's do that.
Reported-by: Kim Phillips <kim.phillips@arm.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
[ardb: clarify comment and commit log, drop unneeded parens]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Fixes: 6f26b3671184c36d ("arm64: kaslr: increase randomization granularity")
Link: http://lkml.kernel.org/r/20180518140841.9731-2-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
