| Age | Commit message (Collapse) | Author |
|---|
|
Meteor Lake TCSS(Type-C Subsystem) xHCI needs to be runtime suspended
whenever possible to allow the TCSS hardware block to enter D3cold and
thus save energy.
Cc: stable@kernel.org
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the same way as Intel Alder Lake TCSS (Type-C Subsystem) the Raptor
Lake TCSS xHCI needs to be runtime suspended whenever possible to
allow the TCSS hardware block to enter D3cold and thus save energy.
Cc: stable@kernel.org
Signed-off-by: Tanveer Alam <tanveer1.alam@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
irq is disabled in xhci_quiesce(called by xhci_halt, with bit:2 cleared
in USBCMD register), but xhci_run(called by usb_add_hcd) re-enable it.
It's possible that you will receive thousands of interrupt requests
after initialization for 2.0 roothub. And you will get a lot of
warning like, "xHCI dying, ignoring interrupt. Shouldn't IRQs be
disabled?". This amount of interrupt requests will cause the entire
system to freeze.
This problem was first found on a device with ASM2142 host controller
on it.
[tidy up old code while moving it, reword header -Mathias]
Cc: stable@kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 5.19-rc4
Here are some new modem device ids and support for further PL2303
device types.
All but the final commit (RM500K device id) have been in linux-next and
with no reported issues.
* tag 'usb-serial-5.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add Quectel RM500K module support
USB: serial: option: add Quectel EM05-G modem
USB: serial: pl2303: add support for more HXN (G) types
USB: serial: option: add Telit LE910Cx 0x1250 composition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf and netfilter.
Current release - regressions:
- netfilter: cttimeout: fix slab-out-of-bounds read in
cttimeout_net_exit
Current release - new code bugs:
- bpf: ftrace: keep address offset in ftrace_lookup_symbols
- bpf: force cookies array to follow symbols sorting
Previous releases - regressions:
- ipv4: ping: fix bind address validity check
- tipc: fix use-after-free read in tipc_named_reinit
- eth: veth: add updating of trans_start
Previous releases - always broken:
- sock: redo the psock vs ULP protection check
- netfilter: nf_dup_netdev: fix skb_under_panic
- bpf: fix request_sock leak in sk lookup helpers
- eth: igb: fix a use-after-free issue in igb_clean_tx_ring
- eth: ice: prohibit improper channel config for DCB
- eth: at803x: fix null pointer dereference on AR9331 phy
- eth: virtio_net: fix xdp_rxq_info bug after suspend/resume
Misc:
- eth: hinic: replace memcpy() with direct assignment"
* tag 'net-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (47 commits)
net: openvswitch: fix parsing of nw_proto for IPv6 fragments
sock: redo the psock vs ULP protection check
Revert "net/tls: fix tls_sk_proto_close executed repeatedly"
virtio_net: fix xdp_rxq_info bug after suspend/resume
igb: Make DMA faster when CPU is active on the PCIe link
net: dsa: qca8k: reduce mgmt ethernet timeout
net: dsa: qca8k: reset cpu port on MTU change
MAINTAINERS: Add a maintainer for OCP Time Card
hinic: Replace memcpy() with direct assignment
Revert "drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c"
net: phy: smsc: Disable Energy Detect Power-Down in interrupt mode
ice: ethtool: Prohibit improper channel config for DCB
ice: ethtool: advertise 1000M speeds properly
ice: Fix switchdev rules book keeping
ice: ignore protocol field in GTP offload
netfilter: nf_dup_netdev: add and use recursion counter
netfilter: nf_dup_netdev: do not push mac header a second time
selftests: netfilter: correct PKTGEN_SCRIPT_PATHS in nft_concat_range.sh
net/tls: fix tls_sk_proto_close executed repeatedly
erspan: do not assume transport header is always set
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- mtk-sd: Fix dma hang issues
- sdhci-pci-o2micro: Fix card detect by dealing with debouncing
* tag 'mmc-v5.19-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: mediatek: wait dma stop bit reset to 0
mmc: sdhci-pci-o2micro: Fix card detect by dealing with debouncing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All small changes, mostly device-specific:
- A regression fix for PCM WC-page allocation on x86
- A regression fix for i915 audio component binding
- Fixes for (longstanding) beep handling bug
- Runtime PM fixes for Intel LPE HDMI audio
- A couple of pending FireWire fixes
- Usual HD-audio and USB-audio quirks, new Intel dspconf entries"
* tag 'sound-5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirk for Clevo NS50PU
ALSA: hda: Fix discovery of i915 graphics PCI device
ALSA: hda/via: Fix missing beep setup
ALSA: hda/conexant: Fix missing beep setup
ALSA: memalloc: Drop x86-specific hack for WC allocations
ALSA: hda/realtek: Add quirk for Clevo PD70PNT
ALSA: x86: intel_hdmi_audio: use pm_runtime_resume_and_get()
ALSA: x86: intel_hdmi_audio: enable pm_runtime and set autosuspend delay
ALSA: hda: intel-nhlt: remove use of __func__ in dev_dbg
ALSA: hda: intel-dspcfg: use SOF for UpExtreme and UpExtreme11 boards
firewire: convert sysfs sprintf/snprintf family to sysfs_emit
firewire: cdev: fix potential leak of kernel stack due to uninitialized value
ALSA: hda/realtek: Apply fixup for Lenovo Yoga Duet 7 properly
ALSA: hda/realtek - ALC897 headset MIC no sound
ALSA: usb-audio: US16x08: Move overflow check before array access
ALSA: hda/realtek: Add mute LED quirk for HP Omen laptop
|
|
unmap_grant_pages() currently waits for the pages to no longer be used.
In https://github.com/QubesOS/qubes-issues/issues/7481, this lead to a
deadlock against i915: i915 was waiting for gntdev's MMU notifier to
finish, while gntdev was waiting for i915 to free its pages. I also
believe this is responsible for various deadlocks I have experienced in
the past.
Avoid these problems by making unmap_grant_pages async. This requires
making it return void, as any errors will not be available when the
function returns. Fortunately, the only use of the return value is a
WARN_ON(), which can be replaced by a WARN_ON when the error is
detected. Additionally, a failed call will not prevent further calls
from being made, but this is harmless.
Because unmap_grant_pages is now async, the grant handle will be sent to
INVALID_GRANT_HANDLE too late to prevent multiple unmaps of the same
handle. Instead, a separate bool array is allocated for this purpose.
This wastes memory, but stuffing this information in padding bytes is
too fragile. Furthermore, it is necessary to grab a reference to the
map before making the asynchronous call, and release the reference when
the call returns.
It is also necessary to guard against reentrancy in gntdev_map_put(),
and to handle the case where userspace tries to map a mapping whose
contents have not all been freed yet.
Fixes: 745282256c75 ("xen/gntdev: safely unmap grants in case they are still in use")
Cc: stable@vger.kernel.org
Signed-off-by: Demi Marie Obenour <demi@invisiblethingslab.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220622022726.2538-1-demi@invisiblethingslab.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
This device shares the PCI ID with the Samsung 970 Evo Plus that
does not need or want the quirks. Move the the quirk entry to the
core table based on the model number instead.
Fixes: bc360b0b1611 ("nvme-pci: add quirks for Samsung X5 SSDs")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Pankaj Raghav <p.raghav@samsung.com>
|
|
The Micron MTFDKBA2T0TFH device reports the same subsysem NQN for
all devices. Add a quick to ignore it.
Signed-off-by: Leo Savernik <l.savernik@aon.at>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add usb product id of the Quectel RM500K module.
RM500K provides 2 mandatory interfaces to Linux host after enumeration.
- /dev/ttyUSB5: this is a serial interface for control path. User needs
to write AT commands to this device node to query status, set APN,
set PIN code, and enable/disable the data connection to 5G network.
- ethX: this is the data path provided as a RNDIS devices. After the
data connection has been established, Linux host can access 5G data
network via this interface.
"RNDIS": RNDIS + ADB + AT (/dev/ttyUSB5) + MODEM COMs
usb-devices output for 0x7001:
T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=7001 Rev=00.01
S: Manufacturer=MediaTek Inc.
S: Product=USB DATA CARD
S: SerialNumber=869206050009672
C: #Ifs=10 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=02 Prot=ff Driver=rndis_host
E: Ad=82(I) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 1 Alt= 0 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=rndis_host
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 7 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I: If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Co-developed-by: Ballon Shi <ballon.shi@quectel.com>
Signed-off-by: Ballon Shi <ballon.shi@quectel.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The following sequence currently causes a driver bug warning
when using virtio_net:
# ip link set eth0 up
# echo mem > /sys/power/state (or e.g. # rtcwake -s 10 -m mem)
<resume>
# ip link set eth0 down
Missing register, driver bug
WARNING: CPU: 0 PID: 375 at net/core/xdp.c:138 xdp_rxq_info_unreg+0x58/0x60
Call trace:
xdp_rxq_info_unreg+0x58/0x60
virtnet_close+0x58/0xac
__dev_close_many+0xac/0x140
__dev_change_flags+0xd8/0x210
dev_change_flags+0x24/0x64
do_setlink+0x230/0xdd0
...
This happens because virtnet_freeze() frees the receive_queue
completely (including struct xdp_rxq_info) but does not call
xdp_rxq_info_unreg(). Similarly, virtnet_restore() sets up the
receive_queue again but does not call xdp_rxq_info_reg().
Actually, parts of virtnet_freeze_down() and virtnet_restore_up()
are almost identical to virtnet_close() and virtnet_open(): only
the calls to xdp_rxq_info_(un)reg() are missing. This means that
we can fix this easily and avoid such problems in the future by
just calling virtnet_close()/open() from the freeze/restore handlers.
Aside from adding the missing xdp_rxq_info calls the only difference
is that the refill work is only cancelled if netif_running(). However,
this should not make any functional difference since the refill work
should only be active if the network interface is actually up.
Fixes: 754b8a21a96d ("virtio_net: setup xdp_rxq_info")
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/r/20220621114845.3650258-1-stephan.gerhold@kernkonzept.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-06-21
This series contains updates to ice driver only.
Marcin fixes GTP filters by allowing ignoring of the inner ethertype field.
Wojciech adds VSI handle tracking in order to properly distinguish similar
filters for removal.
Anatolii removes ability to set 1000baseT and 1000baseX fields
concurrently which caused link issues. He also disallows setting
channels to less than the number of Traffic Classes which would cause
NULL pointer dereference.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: ethtool: Prohibit improper channel config for DCB
ice: ethtool: advertise 1000M speeds properly
ice: Fix switchdev rules book keeping
ice: ignore protocol field in GTP offload
====================
Link: https://lore.kernel.org/r/20220621224756.631765-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Intel I210 on some Intel Alder Lake platforms can only achieve ~750Mbps
Tx speed via iperf. The RR2DCDELAY shows around 0x2xxx DMA delay, which
will be significantly lower when 1) ASPM is disabled or 2) SoC package
c-state stays above PC3. When the RR2DCDELAY is around 0x1xxx the Tx
speed can reach to ~950Mbps.
According to the I210 datasheet "8.26.1 PCIe Misc. Register - PCIEMISC",
"DMA Idle Indication" doesn't seem to tie to DMA coalesce anymore, so
set it to 1b for "DMA is considered idle when there is no Rx or Tx AND
when there are no TLPs indicating that CPU is active detected on the
PCIe link (such as the host executes CSR or Configuration register read
or write operation)" and performing Tx should also fall under "active
CPU on PCIe link" case.
In addition to that, commit b6e0c419f040 ("igb: Move DMA Coalescing init
code to separate function.") seems to wrongly changed from enabling
E1000_PCIEMISC_LX_DECISION to disabling it, also fix that.
Fixes: b6e0c419f040 ("igb: Move DMA Coalescing init code to separate function.")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220621221056.604304-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The current mgmt ethernet timeout is set to 100ms. This value is too
big and would slow down any mdio command in case the mgmt ethernet
packet have some problems on the receiving part.
Reduce it to just 5ms to handle case when some operation are done on the
master port that would cause the mgmt ethernet to not work temporarily.
Fixes: 5950c7c0a68c ("net: dsa: qca8k: add support for mgmt read/write in Ethernet packet")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151633.11741-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was discovered that the Documentation lacks of a fundamental detail
on how to correctly change the MAX_FRAME_SIZE of the switch.
In fact if the MAX_FRAME_SIZE is changed while the cpu port is on, the
switch panics and cease to send any packet. This cause the mgmt ethernet
system to not receive any packet (the slow fallback still works) and
makes the device not reachable. To recover from this a switch reset is
required.
To correctly handle this, turn off the cpu ports before changing the
MAX_FRAME_SIZE and turn on again after the value is applied.
Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20220621151122.10220-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For DCN20 and above, the code that actually hooks up the provided
input_color_space got lost at some point.
Fixes COLOR_ENCODING and COLOR_RANGE doing nothing on DCN20+.
Tested using Steam Remote Play Together + gamescope.
Update other DCNs the same wasy DCN1.x was updates in
commit a1e07ba89d49 ("drm/amd/display: Use plane->color_space for dpp if specified")
Fixes: a1e07ba89d49 ("drm/amd/display: Use plane->color_space for dpp if specified")
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
The function currently skips overriding the drive
settings of the first lane.
[How]
Change for loop to start at 0 instead of 1.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why]
Wrong index was checked for dcfclk_mhz, causing false warning.
[How]
Fix the assertion index.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.18.x
|
|
enabled"
A variety of Lenovo machines with Rembrandt APUs and OLED panels have
stopped showing the display at login. This behavior clears up after
leaving it idle and moving the mouse or touching keyboard.
It was bisected to be caused by commit 559e2655220d ("drm/amd/display:
keep eDP Vdd on when eDP stream is already enabled"). Revert this commit
to fix the issue.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2047
Reported-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: 559e2655220d ("drm/amd/display: keep eDP Vdd on when eDP stream is already enabled")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Certain GL unit tests for large textures can cause problems
with the OOM killer since there is no way to link this memory
to a process. This was originally mitigated (but not necessarily
eliminated) by limiting the GTT size. The problem is this limit
is often too low for many modern games so just make the limit 1/2
of system memory. The OOM accounting needs to be addressed, but
we shouldn't prevent common 3D applications from being usable
just to potentially mitigate that corner case.
Set default GTT size to max(3G, 1/2 of system ram) by default.
v2: drop previous logic and default to 3/4 of ram
v3: default to half of ram to align with ttm
v4: fix spelling in comment (Kent)
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1942
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Under CONFIG_FORTIFY_SOURCE=y and CONFIG_UBSAN_BOUNDS=y, Clang is bugged
here for calculating the size of the destination buffer (0x10 instead of
0x14). This copy is a fixed size (sizeof(struct fw_section_info_st)), with
the source and dest being struct fw_section_info_st, so the memcpy should
be safe, assuming the index is within bounds, which is UBSAN_BOUNDS's
responsibility to figure out.
Avoid the whole thing and just do a direct assignment. This results in
no change to the executable code.
[This is a duplicate of commit 2c0ab32b73cf ("hinic: Replace memcpy()
with direct assignment") which was applied to net-next.]
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: Tom Rix <trix@redhat.com>
Cc: llvm@lists.linux.dev
Link: https://github.com/ClangBuiltLinux/linux/issues/1592
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Tested-by: Nathan Chancellor <nathan@kernel.org> # build
Link: https://lore.kernel.org/r/20220616052312.292861-1-keescook@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Consider '*' alignment in comments
Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Added return statement in sun4i_layer_format_mod_supported()
in case frontend is not present.
Signed-off-by: Saud Farooqui <farooqui_saud@hotmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/PA4P189MB1421E93EF5F8E8E00E71B7878BB29@PA4P189MB1421.EURP189.PROD.OUTLOOK.COM
|
|
The vc4_check_tex_size() function is supposed to return false on error
but this error path accidentally returns -ENODEV (which means true).
Fixes: 30f8c74ca9b7 ("drm/vc4: Warn if some v3d code is run on BCM2711")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/YrMKK89/viQiaiAg@kili
|
|
Fix compatible string for R-Car Gen4.
Fixes: ae684caf465b ("iommu/ipmmu-vmsa: Add support for R-Car Gen4")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220617010107.3229784-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
vxge-main.c"
This reverts commit 8fc74d18639a2402ca52b177e990428e26ea881f.
BAR0 is the main (only?) register bank for this device. We most
obviously can't unmap it before the netdev is unregistered.
This was pointed out in review but the patch got reposted and
merged, anyway.
The author of the patch was only testing it with a QEMU model,
which I presume does not emulate enough for the netdev to be brought
up (author's replies are not visible in lore because they kept sending
their emails in HTML).
Link: https://lore.kernel.org/all/20220616085059.680dc215@kernel.org/
Fixes: 8fc74d18639a ("drivers/net/ethernet/neterion/vxge: Fix a use-after-free bug in vxge-main.c")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to divide the sub-irq status register offset by register
stride to get an index for the status buffer to avoid an out of
bounds write when the register stride is greater than 1.
Fixes: a2d21848d921 ("regmap: regmap-irq: Add main status register support")
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220620200644.1961936-3-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When enabling a type_in_mask irq, the type_buf contents must be
AND'd with the mask of the IRQ we're enabling to avoid enabling
other IRQs by accident, which can happen if several type_in_mask
irqs share a mask register.
Fixes: bc998a730367 ("regmap: irq: handle HW using separate rising/falling edge interrupts")
Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com>
Link: https://lore.kernel.org/r/20220620200644.1961936-2-aidanmacdonald.0x0@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Kernel occasionally complains that there is mismatch in segment size
when trying to render HW decoded videos and rendering them directly with
sun4i DRM driver. Following message can be observed on H6 SoC:
[ 184.298308] ------------[ cut here ]------------
[ 184.298326] DMA-API: sun4i-drm display-engine: mapping sg segment longer than device claims to support [len=6144000] [max=65536]
[ 184.298364] WARNING: CPU: 1 PID: 382 at kernel/dma/debug.c:1162 debug_dma_map_sg+0x2b0/0x350
[ 184.322997] CPU: 1 PID: 382 Comm: ffmpeg Not tainted 5.19.0-rc1+ #1331
[ 184.329533] Hardware name: Tanix TX6 (DT)
[ 184.333544] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 184.340512] pc : debug_dma_map_sg+0x2b0/0x350
[ 184.344882] lr : debug_dma_map_sg+0x2b0/0x350
[ 184.349250] sp : ffff800009f33a50
[ 184.352567] x29: ffff800009f33a50 x28: 0000000000010000 x27: ffff000001b86c00
[ 184.359725] x26: ffffffffffffffff x25: ffff000005d8cc80 x24: 0000000000000000
[ 184.366879] x23: ffff80000939ab18 x22: 0000000000000001 x21: 0000000000000001
[ 184.374031] x20: 0000000000000000 x19: ffff0000018a7410 x18: ffffffffffffffff
[ 184.381186] x17: 0000000000000000 x16: 0000000000000000 x15: ffffffffffffffff
[ 184.388338] x14: 0000000000000001 x13: ffff800009534e86 x12: 6f70707573206f74
[ 184.395493] x11: 20736d69616c6320 x10: 000000000000000a x9 : 0000000000010000
[ 184.402647] x8 : ffff8000093b6d40 x7 : ffff800009f33850 x6 : 000000000000000c
[ 184.409800] x5 : ffff0000bf997940 x4 : 0000000000000000 x3 : 0000000000000027
[ 184.416953] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000003960e80
[ 184.424106] Call trace:
[ 184.426556] debug_dma_map_sg+0x2b0/0x350
[ 184.430580] __dma_map_sg_attrs+0xa0/0x110
[ 184.434687] dma_map_sgtable+0x28/0x4c
[ 184.438447] vb2_dc_dmabuf_ops_map+0x60/0xcc
[ 184.442729] __map_dma_buf+0x2c/0xd4
[ 184.446321] dma_buf_map_attachment+0xa0/0x130
[ 184.450777] drm_gem_prime_import_dev+0x7c/0x18c
[ 184.455410] drm_gem_prime_fd_to_handle+0x1b8/0x214
[ 184.460300] drm_prime_fd_to_handle_ioctl+0x2c/0x40
[ 184.465190] drm_ioctl_kernel+0xc4/0x174
[ 184.469123] drm_ioctl+0x204/0x420
[ 184.472534] __arm64_sys_ioctl+0xac/0xf0
[ 184.476474] invoke_syscall+0x48/0x114
[ 184.480240] el0_svc_common.constprop.0+0x44/0xec
[ 184.484956] do_el0_svc+0x2c/0xc0
[ 184.488283] el0_svc+0x2c/0x84
[ 184.491354] el0t_64_sync_handler+0x11c/0x150
[ 184.495723] el0t_64_sync+0x18c/0x190
[ 184.499397] ---[ end trace 0000000000000000 ]---
Fix that by setting DMA mask and segment size.
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620181333.650301-1-jernej.skrabec@gmail.com
|
|
Multiplying ints and saving it in unsigned long long
could lead to integer overflow before being type casted to
unsigned long long.
Addresses-Coverity: 1505113: Unintentional integer overflow.
Signed-off-by: Saud Farooqui <farooqui_saud@hotmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/PA4P189MB1421E63C0FF3EBF234A80AB38BA79@PA4P189MB1421.EURP189.PROD.OUTLOOK.COM
|
|
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030a Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030a Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Yonglin Tan <yonglin.tan@outlook.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Add support for further HXN (G) type devices (GT variant, GL variant, GS
variant and GR) and document the bcdDevice mapping.
Note that the TA and TB types use the same bcdDevice as some GT and GE
variants, respectively, but that the HX status request can be used to
determine which is which.
Also note that we currently do not distinguish between the various HXN
(G) types in the driver but that this may change eventually (e.g. when
adding GPIO support).
Reported-by: Charles Yeh <charlesyeh522@gmail.com>
Link: https://lore.kernel.org/r/YrF77b9DdeumUAee@hovoldconsulting.com
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Simon reports that if two LAN9514 USB adapters are directly connected
without an intermediate switch, the link fails to come up and link LEDs
remain dark. The issue was introduced by commit 1ce8b37241ed ("usbnet:
smsc95xx: Forward PHY interrupts to PHY driver to avoid polling").
The PHY suffers from a known erratum wherein link detection becomes
unreliable if Energy Detect Power-Down is used. In poll mode, the
driver works around the erratum by briefly disabling EDPD for 640 msec
to detect a neighbor, then re-enabling it to save power.
In interrupt mode, no interrupt is signaled if EDPD is used by both link
partners, so it must not be enabled at all.
We'll recoup the power savings by enabling SUSPEND1 mode on affected
LAN95xx chips in a forthcoming commit.
Fixes: 1ce8b37241ed ("usbnet: smsc95xx: Forward PHY interrupts to PHY driver to avoid polling")
Reported-by: Simon Han <z.han@kunbus.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/439a3f3168c2f9d44b5fd9bb8d2b551711316be6.1655714438.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Do not allow setting less channels, than Traffic Classes there are
via ethtool. There must be at least one channel per Traffic Class.
If you set less channels, than Traffic Classes there are, then during
ice_vsi_rebuild there would be allocated only the requested amount
of tx/rx rings in ice_vsi_alloc_arrays. But later in ice_vsi_setup_q_map
there would be requested at least one channel per Traffic Class. This
results in setting num_rxq > alloc_rxq and num_txq > alloc_txq.
Later, there would be a NULL pointer dereference in
ice_vsi_map_rings_to_vectors, because we go beyond of rx_rings or
tx_rings arrays.
Change ice_set_channels() to return error if you try to allocate less
channels, than Traffic Classes there are.
Change ice_vsi_setup_q_map() and ice_vsi_setup_q_map_mqprio() to return
status code instead of void.
Add error handling for ice_vsi_setup_q_map() and
ice_vsi_setup_q_map_mqprio() in ice_vsi_init() and ice_vsi_cfg_tc().
[53753.889983] INFO: Flow control is disabled for this traffic class (0) on this vsi.
[53763.984862] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
[53763.992915] PGD 14b45f5067 P4D 0
[53763.996444] Oops: 0002 [#1] SMP NOPTI
[53764.000312] CPU: 12 PID: 30661 Comm: ethtool Kdump: loaded Tainted: GOE --------- - - 4.18.0-240.el8.x86_64 #1
[53764.011825] Hardware name: Intel Corporation WilsonCity/WilsonCity, BIOS WLYDCRB1.SYS.0020.P21.2012150710 12/15/2020
[53764.022584] RIP: 0010:ice_vsi_map_rings_to_vectors+0x7e/0x120 [ice]
[53764.029089] Code: 41 0d 0f b7 b7 12 05 00 00 0f b6 d0 44 29 de 44 0f b7 c6 44 01 c2 41 39 d0 7d 2d 4c 8b 47 28 44 0f b7 ce 83 c6 01 4f 8b 04 c8 <49> 89 48 28 4 c 8b 89 b8 01 00 00 4d 89 08 4c 89 81 b8 01 00 00 44
[53764.048379] RSP: 0018:ff550dd88ea47b20 EFLAGS: 00010206
[53764.053884] RAX: 0000000000000002 RBX: 0000000000000004 RCX: ff385ea42fa4a018
[53764.061301] RDX: 0000000000000006 RSI: 0000000000000005 RDI: ff385e9baeedd018
[53764.068717] RBP: 0000000000000010 R08: 0000000000000000 R09: 0000000000000004
[53764.076133] R10: 0000000000000002 R11: 0000000000000004 R12: 0000000000000000
[53764.083553] R13: 0000000000000000 R14: ff385e658fdd9000 R15: ff385e9baeedd018
[53764.090976] FS: 000014872c5b5740(0000) GS:ff385e847f100000(0000) knlGS:0000000000000000
[53764.099362] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[53764.105409] CR2: 0000000000000028 CR3: 0000000a820fa002 CR4: 0000000000761ee0
[53764.112851] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[53764.120301] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[53764.127747] PKRU: 55555554
[53764.130781] Call Trace:
[53764.133564] ice_vsi_rebuild+0x611/0x870 [ice]
[53764.138341] ice_vsi_recfg_qs+0x94/0x100 [ice]
[53764.143116] ice_set_channels+0x1a8/0x3e0 [ice]
[53764.147975] ethtool_set_channels+0x14e/0x240
[53764.152667] dev_ethtool+0xd74/0x2a10
[53764.156665] ? __mod_lruvec_state+0x44/0x110
[53764.161280] ? __mod_lruvec_state+0x44/0x110
[53764.165893] ? page_add_file_rmap+0x15/0x170
[53764.170518] ? inet_ioctl+0xd1/0x220
[53764.174445] ? netdev_run_todo+0x5e/0x290
[53764.178808] dev_ioctl+0xb5/0x550
[53764.182485] sock_do_ioctl+0xa0/0x140
[53764.186512] sock_ioctl+0x1a8/0x300
[53764.190367] ? selinux_file_ioctl+0x161/0x200
[53764.195090] do_vfs_ioctl+0xa4/0x640
[53764.199035] ksys_ioctl+0x60/0x90
[53764.202722] __x64_sys_ioctl+0x16/0x20
[53764.206845] do_syscall_64+0x5b/0x1a0
[53764.210887] entry_SYSCALL_64_after_hwframe+0x65/0xca
Fixes: 87324e747fde ("ice: Implement ethtool ops for channels")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Adding two filters with same matching criteria ends up with
one rule in hardware with act = ICE_FWD_TO_VSI_LIST.
In order to remove them properly we have to keep the
information about vsi handle which is used in VSI bitmap
(ice_adv_fltr_mgmt_list_entry::vsi_list_info::vsi_map).
Fixes: 0d08a441fb1a ("ice: ndo_setup_tc implementation for PF")
Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 34a897758efe ("ice: Add support for inner etype in switchdev")
added the ability to match on inner ethertype. A side effect of that change
is that it is now impossible to add some filters for protocols which do not
contain inner ethtype field. tc requires the protocol field to be specified
when providing certain other options, e.g. src_ip. This is a problem in
case of GTP - when user wants to specify e.g. src_ip, they also need to
specify protocol in tc command (otherwise tc fails with: Illegal "src_ip").
Because GTP is a tunnel, the protocol field is treated as inner protocol.
GTP does not contain inner ethtype field and the filter cannot be added.
To fix this, ignore the ethertype field in case of GTP filters.
Fixes: 9a225f81f540 ("ice: Support GTP-U and GTP-C offload in switchdev")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 5291984004edf ("dm: fix bio polling to handle possibile
BLK_STS_AGAIN") inadvertently introduced an early return from
dm_io_complete() without first queueing the bio to DM if BLK_STS_AGAIN
occurs and bio-polling is _not_ being used.
Fix this by only returning early from dm_io_complete() if the bio has
first been properly queued to DM. Otherwise, the bio will never finish
via bio_endio.
Fixes: 5291984004edf ("dm: fix bio polling to handle possibile BLK_STS_AGAIN")
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
During postsuspend dm-era does the following:
1. Archives the current era
2. Commits the metadata, as part of the RPC call for archiving the
current era
3. Stops the worker
Until the worker stops, it might write to the metadata again. Moreover,
these writes are not flushed to disk immediately, but are cached by the
dm-bufio client, which writes them back asynchronously.
As a result, the committed metadata of a suspended dm-era device might
not be consistent with the in-core metadata.
In some cases, this can result in the corruption of the on-disk
metadata. Suppose the following sequence of events:
1. Load a new table, e.g. a snapshot-origin table, to a device with a
dm-era table
2. Suspend the device
3. dm-era commits its metadata, but the worker does a few more metadata
writes until it stops, as part of digesting an archived writeset
4. These writes are cached by the dm-bufio client
5. Load the dm-era table to another device.
6. The new instance of the dm-era target loads the committed, on-disk
metadata, which don't include the extra writes done by the worker
after the metadata commit.
7. Resume the new device
8. The new dm-era target instance starts using the metadata
9. Resume the original device
10. The destructor of the old dm-era target instance is called and
destroys the dm-bufio client, which results in flushing the cached
writes to disk
11. These writes might overwrite the writes done by the new dm-era
instance, hence corrupting its metadata.
Fix this by committing the metadata after the worker stops running.
stop_worker uses flush_workqueue to flush the current work. However, the
work item may re-queue itself and flush_workqueue doesn't wait for
re-queued works to finish.
This could result in the worker changing the metadata after they have
been committed, or writing to the metadata concurrently with the commit
in the postsuspend thread.
Use drain_workqueue instead, which waits until the work and all
re-queued works finish.
Fixes: eec40579d8487 ("dm: add era target")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Nikos Tsironis <ntsironis@arrikto.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull EFI fixes from Ard Biesheuvel:
- remove pointless include of asm/efi.h, which does not exist on ia64
- fix DXE service marshalling prototype for mixed mode
* tag 'efi-urgent-for-v5.19-1' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi/x86: libstub: Fix typo in __efi64_argmap* name
efi: sysfb_efi: remove unnecessary <asm/efi.h> include
|
|
Nothing defined in the header is used by drivers/firmware/efi/sysfb_efi.c
but also, including it can lead to build errors when built on arches that
don't have an asm/efi.h header file.
This can happen for example if a driver that is built when COMPILE_TEST is
enabled selects the SYSFB symbol, e.g. on powerpc with allyesconfig:
drivers/firmware/efi/sysfb_efi.c:29:10: fatal error: asm/efi.h: No such file or directory
29 | #include <asm/efi.h>
| ^~~~~~~~~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
commit 979934da9e7a ("[PATCH] mips: update IRQ handling for vr41xx") added
a function irq_dispatch, and it'll increase irq_err_count when the get_irq
callback returns a negative value, but increase irq_err_count in get_irq
was not removed.
And also, modpost complains once gpio-vr41xx drivers become modules.
ERROR: modpost: "irq_err_count" [drivers/gpio/gpio-vr41xx.ko] undefined!
So it would be a good idea to remove repetitive increase irq_err_count in
get_irq callback.
Fixes: 27fdd325dace ("MIPS: Update VR41xx GPIO driver to use gpiolib")
Fixes: 979934da9e7a ("[PATCH] mips: update IRQ handling for vr41xx")
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: huhai <huhai@kylinos.cn>
Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
With Xen PV Display driver in use the "expected" VM_DONTEXPAND flag
is not set (neither explicitly nor implicitly), so the driver hits
the code path in drm_gem_mmap_obj() which triggers the WARNING.
Signed-off-by: Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Link: https://lore.kernel.org/r/1652104303-5098-1-git-send-email-olekstysh@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
1 << 31 is undefined. So switch to 1U << 31.
Fixes: 5ead97c84fa7 ("xen: Core Xen implementation")
Signed-off-by: Julien Grall <jgrall@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220617103037.57828-1-julien@xen.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When a VBD is not fully created and then closed, the kernel can have a
NULL pointer dereference:
The reproducer is trivial:
[user@dom0 ~]$ sudo xl block-attach work backend=sys-usb vdev=xvdi target=/dev/sdz
[user@dom0 ~]$ xl block-list work
Vdev BE handle state evt-ch ring-ref BE-path
51712 0 241 4 -1 -1 /local/domain/0/backend/vbd/241/51712
51728 0 241 4 -1 -1 /local/domain/0/backend/vbd/241/51728
51744 0 241 4 -1 -1 /local/domain/0/backend/vbd/241/51744
51760 0 241 4 -1 -1 /local/domain/0/backend/vbd/241/51760
51840 3 241 3 -1 -1 /local/domain/3/backend/vbd/241/51840
^ note state, the /dev/sdz doesn't exist in the backend
[user@dom0 ~]$ sudo xl block-detach work xvdi
[user@dom0 ~]$ xl block-list work
Vdev BE handle state evt-ch ring-ref BE-path
work is an invalid domain identifier
And its console has:
BUG: kernel NULL pointer dereference, address: 0000000000000050
PGD 80000000edebb067 P4D 80000000edebb067 PUD edec2067 PMD 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 52 Comm: xenwatch Not tainted 5.16.18-2.43.fc32.qubes.x86_64 #1
RIP: 0010:blk_mq_stop_hw_queues+0x5/0x40
Code: 00 48 83 e0 fd 83 c3 01 48 89 85 a8 00 00 00 41 39 5c 24 50 77 c0 5b 5d 41 5c 41 5d c3 c3 0f 1f 80 00 00 00 00 0f 1f 44 00 00 <8b> 47 50 85 c0 74 32 41 54 49 89 fc 55 53 31 db 49 8b 44 24 48 48
RSP: 0018:ffffc90000bcfe98 EFLAGS: 00010293
RAX: ffffffffc0008370 RBX: 0000000000000005 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000005 RDI: 0000000000000000
RBP: ffff88800775f000 R08: 0000000000000001 R09: ffff888006e620b8
R10: ffff888006e620b0 R11: f000000000000000 R12: ffff8880bff39000
R13: ffff8880bff39000 R14: 0000000000000000 R15: ffff88800604be00
FS: 0000000000000000(0000) GS:ffff8880f3300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000050 CR3: 00000000e932e002 CR4: 00000000003706e0
Call Trace:
<TASK>
blkback_changed+0x95/0x137 [xen_blkfront]
? read_reply+0x160/0x160
xenwatch_thread+0xc0/0x1a0
? do_wait_intr_irq+0xa0/0xa0
kthread+0x16b/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Modules linked in: snd_seq_dummy snd_hrtimer snd_seq snd_seq_device snd_timer snd soundcore ipt_REJECT nf_reject_ipv4 xt_state xt_conntrack nft_counter nft_chain_nat xt_MASQUERADE nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nft_compat nf_tables nfnetlink intel_rapl_msr intel_rapl_common crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel xen_netfront pcspkr xen_scsiback target_core_mod xen_netback xen_privcmd xen_gntdev xen_gntalloc xen_blkback xen_evtchn ipmi_devintf ipmi_msghandler fuse bpf_preload ip_tables overlay xen_blkfront
CR2: 0000000000000050
---[ end trace 7bc9597fd06ae89d ]---
RIP: 0010:blk_mq_stop_hw_queues+0x5/0x40
Code: 00 48 83 e0 fd 83 c3 01 48 89 85 a8 00 00 00 41 39 5c 24 50 77 c0 5b 5d 41 5c 41 5d c3 c3 0f 1f 80 00 00 00 00 0f 1f 44 00 00 <8b> 47 50 85 c0 74 32 41 54 49 89 fc 55 53 31 db 49 8b 44 24 48 48
RSP: 0018:ffffc90000bcfe98 EFLAGS: 00010293
RAX: ffffffffc0008370 RBX: 0000000000000005 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000005 RDI: 0000000000000000
RBP: ffff88800775f000 R08: 0000000000000001 R09: ffff888006e620b8
R10: ffff888006e620b0 R11: f000000000000000 R12: ffff8880bff39000
R13: ffff8880bff39000 R14: 0000000000000000 R15: ffff88800604be00
FS: 0000000000000000(0000) GS:ffff8880f3300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000050 CR3: 00000000e932e002 CR4: 00000000003706e0
Kernel panic - not syncing: Fatal exception
Kernel Offset: disabled
info->rq and info->gd are only set in blkfront_connect(), which is
called for state 4 (XenbusStateConnected). Guard against using NULL
variables in blkfront_closing() to avoid the issue.
The rest of blkfront_closing looks okay. If info->nr_rings is 0, then
for_each_rinfo won't do anything.
blkfront_remove also needs to check for non-NULL pointers before
cleaning up the gendisk and request queue.
Fixes: 05d69d950d9d "xen-blkfront: sanitize the removal state machine"
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20220601195341.28581-1-jandryuk@gmail.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Intel SoC PMIC is a generic name for all PMICs that are used
on Intel platforms. In particular, INTEL_SOC_PMIC kernel configuration
option refers to Crystal Cove PMIC, which has never been a part
of any Intel Broxton hardware. Drop wrong dependency from Kconfig.
Note, the correct dependency is satisfied via ACPI PMIC OpRegion driver,
which the Type-C depends on.
Fixes: d2061f9cc32d ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220620104316.57592-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A panic can occur if the endpoint becomes disabled and the
uvcg_video_pump adds the request back to the req_free list after it has
already been queued to the endpoint. The endpoint complete will add the
request back to the req_free list. Invalidate the local request handle
once it's been queued.
<6>[ 246.796704][T13726] configfs-gadget gadget: uvc: uvc_function_set_alt(1, 0)
<3>[ 246.797078][ T26] list_add double add: new=ffffff878bee5c40, prev=ffffff878bee5c40, next=ffffff878b0f0a90.
<6>[ 246.797213][ T26] ------------[ cut here ]------------
<2>[ 246.797224][ T26] kernel BUG at lib/list_debug.c:31!
<6>[ 246.807073][ T26] Call trace:
<6>[ 246.807180][ T26] uvcg_video_pump+0x364/0x38c
<6>[ 246.807366][ T26] process_one_work+0x2a4/0x544
<6>[ 246.807394][ T26] worker_thread+0x350/0x784
<6>[ 246.807442][ T26] kthread+0x2ac/0x320
Fixes: f9897ec0f6d3 ("usb: gadget: uvc: only pump video data if necessary")
Cc: stable@vger.kernel.org
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dan Vacura <w36195@motorola.com>
Link: https://lore.kernel.org/r/20220617163154.16621-1-w36195@motorola.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
