| Age | Commit message (Collapse) | Author |
|---|
|
at_xdmac could be used on SoCs which supports backup mode (where most
of the SoC power, including power to DMA controller, is closed at suspend
time). Thus, on resume, the settings which were previously done need to be
restored. Do the same for axi configuration.
Fixes: f40566f220a1 ("dmaengine: at_xdmac: add AXI priority support and recommended settings")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20211007111230.2331837-2-claudiu.beznea@microchip.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull libata fixes from Damien Le Moal:
"Two fixes for this cycle:
- Fix a null pointer dereference in ahci-platform driver (from Hai)
- Fix uninitialized variables in pata_legacy driver (from Dan)"
* tag 'libata-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: ahci_platform: fix null-ptr-deref in ahci_platform_enable_regulators()
pata_legacy: fix a couple uninitialized variable bugs
|
|
Pull block fixes from Jens Axboe:
"Bigger than usual for this point in time, the majority is fixing some
issues around BDI lifetimes with the move from the request_queue to
the disk in this release. In detail:
- Series on draining fs IO for del_gendisk() (Christoph)
- NVMe pull request via Christoph:
- fix the abort command id (Keith Busch)
- nvme: fix per-namespace chardev deletion (Adam Manzanares)
- brd locking scope fix (Tetsuo)
- BFQ fix (Paolo)"
* tag 'block-5.15-2021-10-17' of git://git.kernel.dk/linux-block:
block, bfq: reset last_bfqq_created on group change
block: warn when putting the final reference on a registered disk
brd: reduce the brd_devices_mutex scope
kyber: avoid q->disk dereferences in trace points
block: keep q_usage_counter in atomic mode after del_gendisk
block: drain file system I/O on del_gendisk
block: split bio_queue_enter from blk_queue_enter
block: factor out a blk_try_enter_queue helper
block: call submit_bio_checks under q_usage_counter
nvme: fix per-namespace chardev deletion
block/rnbd-clt-sysfs: fix a couple uninitialized variable bugs
nvme-pci: Fix abort command id
|
|
Pull virtio fixes from Michael Tsirkin:
"Fixes up some issues in rc5"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost-vdpa: Fix the wrong input in config_cb
VDUSE: fix documentation underline warning
Revert "virtio-blk: Add validation for block size in config space"
vhost_vdpa: unset vq irq before freeing irq
virtio: write back F_VERSION_1 before validate
|
|
The variable err is being initialized with a value that is never read, it
is being updated later on. The assignment is redundant and can be removed
and move the declaration into the local scope.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20211015123447.27560-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
ADMAIF FIFO uses a ring buffer and it is divided amongst the available
channels. The default FIFO size (in multiples of 16 words) of ADMAIF TX/RX
channels is as below:
* On Tegra210,
channel 1 to 2 : size = 3
channel 3 to 10: size = 2
* On Tegra186 and later,
channel 1 to 4 : size = 3
channel 5 to 20: size = 2
As per recommendation from HW, FIFO size of ADMA channel should be same as
the corresponding ADMAIF channel it maps to. FIFO corruption is observed if
the sizes do not match. We are using the default FIFO sizes for ADMAIF and
there is no plan to support any custom values.
Thus at runtime, override the ADMA channel FIFO size value depending on the
corresponding ADMAIF channel.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/1631722025-19873-4-git-send-email-spujar@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Trivial change to add description for 'adma_get_burst_config' in chip
data structure.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/1631722025-19873-3-git-send-email-spujar@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The 'has_outstanding_reqs' member description order in structure
'tegra_adma_chip_data' does not match with the corresponding member
declaration. The same is true for member assignment in chip data
structures declared for Tegra210 and Tegra186.
This is a trivial fix to re-order the mentioned member for a better
readability.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/1631722025-19873-2-git-send-email-spujar@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC fix from Borislav Petkov:
- Log the "correct" uncorrectable error count in the armada_xp driver
* tag 'edac_urgent_for_v5.15_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/armada-xp: Fix output of uncorrectable error counter
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Borislav Petkov:
"Forwarded from Ard Biesheuvel through the tip tree. Ard will send
stuff directly in the near future.
Low priority fixes but fixes nonetheless:
- update stub diagnostic print that is no longer accurate
- avoid statically allocated buffer for CPER error record decoding
- avoid sleeping on the efi_runtime semaphore when calling the
ResetSystem EFI runtime service"
* tag 'efi-urgent-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Change down_interruptible() in virt_efi_reset_system() to down_trylock()
efi/cper: use stack buffer for error record decoding
efi/libstub: Simplify "Exiting bootservices" message
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core fixes for 5.15-rc6, all of which have
been in linux-next for a while with no reported issues.
They include:
- kernfs negative dentry bugfix
- simple pm bus fixes to resolve reported issues"
* tag 'driver-core-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
drivers: bus: Delete CONFIG_SIMPLE_PM_BUS
drivers: bus: simple-pm-bus: Add support for probing simple bus only devices
driver core: Reject pointless SYNC_STATE_ONLY device links
kernfs: don't create a negative dentry if inactive node exists
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char/misc driver fixes for 5.15-rc6 for reported
issues that include:
- habanalabs driver fixes
- mei driver fixes and new ids
- fpga new device ids
- MAINTAINER file updates for fpga subsystem
- spi module id table additions and fixes
- fastrpc locking fixes
- nvmem driver fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
eeprom: 93xx46: fix MODULE_DEVICE_TABLE
nvmem: Fix shift-out-of-bound (UBSAN) with byte size cells
mei: hbm: drop hbm responses on early shutdown
mei: me: add Ice Lake-N device id.
eeprom: 93xx46: Add SPI device ID table
eeprom: at25: Add SPI ID table
misc: HI6421V600_IRQ should depend on HAS_IOMEM
misc: fastrpc: Add missing lock before accessing find_vma()
cb710: avoid NULL pointer subtraction
misc: gehc: Add SPI ID table
MAINTAINERS: Drop outdated FPGA Manager website
MAINTAINERS: Add Hao and Yilun as maintainers
habanalabs: fix resetting args in wait for CS IOCTL
fpga: ice40-spi: Add SPI device ID table
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are a number of small IIO and staging driver fixes for 5.15-rc6.
They include:
- vc04_services bugfix for reported problem
- r8188eu array underflow fix
- iio driver fixes for a lot of tiny reported issues.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: prevent array underflow in rtw_hal_update_ra_mask()
staging: vc04_services: shut up out-of-range warning
iio: light: opt3001: Fixed timeout error when 0 lux
iio: adis16480: fix devices that do not support sleep mode
iio: mtk-auxadc: fix case IIO_CHAN_INFO_PROCESSED
iio: adis16475: fix deadlock on frequency set
iio: ssp_sensors: add more range checking in ssp_parse_dataframe()
iio: ssp_sensors: fix error code in ssp_print_mcu_debug()
iio: adc: ad7793: Fix IRQ flag
iio: adc: ad7780: Fix IRQ flag
iio: adc: ad7192: Add IRQ flag
iio: adc: aspeed: set driver data when adc probe.
iio: adc: rzg2l_adc: add missing clk_disable_unprepare() in rzg2l_adc_pm_runtime_resume()
iio: adc: max1027: Fix the number of max1X31 channels
iio: adc: max1027: Fix wrong shift with 12-bit devices
iio: adc128s052: Fix the error handling path of 'adc128_probe()'
iio: adc: rzg2l_adc: Fix -EBUSY timeout error return
iio: accel: fxls8962af: return IRQ_HANDLED when fifo is flushed
iio: dac: ti-dac5571: fix an error code in probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fix from Greg KH:
"Here is a single 8250 Kconfig fix for 5.15-rc6 that resolves a
regression that showed up in 5.15-rc1. It has been in linux-next for a
while with no reported issues"
* tag 'tty-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250: allow disabling of Freescale 16550 compile test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes that resolve a number of tiny issues.
They include:
- new USB serial driver ids
- xhci driver fixes for a bunch of issues
- musb error path fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: musb: dsps: Fix the probe error path
xhci: Enable trust tx length quirk for Fresco FL11 USB controller
xhci: Fix command ring pointer corruption while aborting a command
USB: xhci: dbc: fix tty registration race
xhci: add quirk for host controllers that don't update endpoint DCS
xhci: guard accesses to ep_state in xhci_endpoint_reset()
USB: serial: qcserial: add EM9191 QDL support
USB: serial: option: add Quectel EC200S-CN module support
USB: serial: option: add prod. id for Quectel EG91
USB: serial: option: add Telit LE910Cx composition 0x1204
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
- a new product ID for the xpad joystick driver
- fixes to resistive-adc-touch and snvs_pwrkey drivers
- a change to touchscreen helpers to make clang happier
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: touchscreen - avoid bitwise vs logical OR warning
Input: xpad - add support for another USB ID of Nacon GC-100
Input: resistive-adc-touch - fix division by zero error on z1 == 0
Input: snvs_pwrkey - add clk handling
|
|
spmi-mpp did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should be
usable from the start without the consumer having to make an additional
call to get the proper IRQ on the parent. This patch adds hierarchical
IRQ chip support to the spmi-mpp code to correct this issue.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-17-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process.
This change will also allow for the removal of the interrupts property
later in this patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,spmi-mpp OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-16-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ssbi-mpp did not have any irqchip support so consumers of this in
device tree would need to call gpio[d]_to_irq() in order to get the
proper IRQ on the underlying PMIC. IRQ chips in device tree should be
usable from the start without the consumer having to make an additional
call to get the proper IRQ on the parent. This patch adds hierarchical
IRQ chip support to the ssbi-mpp code to correct this issue.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-15-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The probing of this driver calls platform_irq_count, which will
setup all of the IRQs that are configured in device tree. In
preparation for converting this driver to be a hierarchical IRQ
chip, hardcode the IRQ count based on the hardware type so that all
the IRQs are not configured immediately and are configured on an
as-needed basis later in the boot process.
This change will also allow for the removal of the interrupts property
later in this patch series once the hierarchical IRQ chip support is in.
This patch also removes the generic qcom,ssbi-mpp OF match since we
don't know the number of pins. All of the existing upstream bindings
already include the more-specific binding.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20211008012524.481877-14-dmitry.baryshkov@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add pinctrl data for ExynosAuto v9 SoC.
- GPA0, GPA1: 10, External wake up interrupt
- GPQ0: 2, XbootLDO, Speedy PMIC I/F
- GPB0, GPB1, GPB2, GPB3: 29, I2S 7 CH
- GPF0, GPF1, GPF2, GPF3,GPF4, GPF5, GPF6, GPF8: 52, FSYS
- GPG0, GPG1, GPG2, GPG3: 25, GPIO x 24, SMPL_INT
- GPP0, GPP1, GPP2, GPP3, GPP4, GPP5: 48, USI 12 CH
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20211008091443.44625-2-chanho61.park@samsung.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211017171912.5044-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
nullity of a pointer
Since alloc_can_err_skb() puts NULL in cf in the case when skb cannot
be allocated and can_change_state() handles the case when cf is NULL,
the test on the nullity of skb is now unnecessary.
Link: https://lore.kernel.org/all/20210929142111.55757-2-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
notification
This corrects the lack of notification of a return to ERROR_ACTIVE
state for USB - CANFD devices from PEAK-System.
Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Link: https://lore.kernel.org/all/20210929142111.55757-1-s.grosjean@peak-system.com
Cc: stable@vger.kernel.org
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When remove the module peek_pci, referencing 'chan' again after
releasing 'dev' will cause UAF.
Fix this by releasing 'dev' later.
The following log reveals it:
[ 35.961814 ] BUG: KASAN: use-after-free in peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.963414 ] Read of size 8 at addr ffff888136998ee8 by task modprobe/5537
[ 35.965513 ] Call Trace:
[ 35.965718 ] dump_stack_lvl+0xa8/0xd1
[ 35.966028 ] print_address_description+0x87/0x3b0
[ 35.966420 ] kasan_report+0x172/0x1c0
[ 35.966725 ] ? peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.967137 ] ? trace_irq_enable_rcuidle+0x10/0x170
[ 35.967529 ] ? peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.967945 ] __asan_report_load8_noabort+0x14/0x20
[ 35.968346 ] peak_pci_remove+0x16f/0x270 [peak_pci]
[ 35.968752 ] pci_device_remove+0xa9/0x250
Fixes: e6d9c80b7ca1 ("can: peak_pci: add support of some new PEAK-System PCI cards")
Link: https://lore.kernel.org/all/1634192913-15639-1-git-send-email-zheyuma97@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The read and writes from the fifo are from a buffer, with various
fields and data at predefined offsets. So, they should not be done to
the same address(or port) in case of val_count greater than 1.
Therefore, fix this by using iowrite32()/ioread32() instead of
ioread32_rep()/iowrite32_rep().
Also, the write into FIFO must be performed with an offset from the
message ram base address. Therefore, fix the base address to
mram_base.
Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20210920123344.2320-1-a-govindraju@ti.com
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the driver was not opened, rcar_can_suspend() should not call
clk_disable() because the clock was not enabled.
Fixes: fd1159318e55 ("can: add Renesas R-Car CAN driver")
Link: https://lore.kernel.org/all/20210924075556.223685-1-yoshihiro.shimoda.uh@renesas.com
Cc: stable@vger.kernel.org
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Ayumi Nakamichi <ayumi.nakamichi.kf@renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
interface
TVAL usage is now long gone, get rid of the leftovers.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-11-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The Applied Micro XGene-1 SoC has a busted implementation of the
CVAL register: it looks like it is based on TVAL instead of the
other way around. The net effect of this implementation blunder
is that the maximum deadline you can program in the timer is
32bit wide.
Use a MIDR check to notice the broken CPU, and reduce the width
of the timer to 32bit.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-10-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Proudly tell the code code that we have a timer able to handle
56 bits deltas.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-9-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Similarily to the sysreg-based timer, move the MMIO over to using
the CVAL registers instead of TVAL. Note that there is no warranty
that the 64bit MMIO access will be atomic, but the timer is always
disabled at the point where we program CVAL.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-8-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
ordering issue
The MMIO timer base address gets published after we have registered
the callbacks and the interrupt handler, which is... a bit dangerous.
Fix this by moving the base address publication to the point where
we register the timer, and expose a pointer to the timer structure
itself rather than a naked value.
Reviewed-by: Oliver Upton <oupton@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-7-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The '_tval' name in the erratum handling function names doesn't
make much sense anymore (and they were using CVAL the first place).
Drop the _tval tag.
Reviewed-by: Oliver Upton <oupton@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-6-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
over to CVAL
In order to cope better with high frequency counters, move the
programming of the timers from the countdown timer (TVAL) over
to the comparator (CVAL).
The programming model is slightly different, as we now need to
read the current counter value to have an absolute deadline
instead of a relative one.
There is a small overhead to this change, which we will address
in the following patches.
Reviewed-by: Oliver Upton <oupton@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-5-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
accessors to u64
The various accessors for the timer sysreg and MMIO registers are
currently hardwired to 32bit. However, we are about to introduce
the use of the CVAL registers, which require a 64bit access.
Upgrade the write side of the accessors to take a 64bit value
(the read side is left untouched as we don't plan to ever read
back any of these registers).
No functional change expected.
Reviewed-by: Oliver Upton <oupton@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-4-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The arch timer driver never reads the various TVAL registers, only
writes to them. It is thus pointless to provide accessors
for them and to implement errata workarounds.
Drop these read-side accessors, and add a couple of BUG() statements
for the time being. These statements will be removed further down
the line.
Reviewed-by: Oliver Upton <oupton@google.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-3-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
accesses
As we are about to change the registers that are used by the driver,
start by adding build-time checks to ensure that we always handle
all registers and access modes.
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20211017124225.3018098-2-maz@kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The config HAVE_S3C_RTC is not really needed since we can simply just
add the dependencies directly to RTC_DRV_S3C. Also, one less config to
keep track of!
Signed-off-by: Will McVicker <willmcvicker@google.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211013212256.3425889-1-willmcvicker@google.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
|
|
This patch adds feature negotiation and ssr ack feature between
local host and remote processor. Local host can negotiate on common
features supported with remote processor.
When ssr ack feature bit is set, the remote processor will tell local
host when it is reinitialized. All clients registered for falling edge
interrupts will be notified when the smp2p entries are cleared for ssr.
Signed-off-by: Chris Lew <clew@codeaurora.org>
Signed-off-by: Deepak Kumar Singh <deesin@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1633450403-21281-1-git-send-email-deesin@codeaurora.org
|
|
Sync if statement with the actual warning.
Fixes: 9504db5765e8 ("iio: adc: tsc2046: fix a warning message in tsc2046_adc_update_scan_mode()")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20211007093007.1466-2-o.rempel@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
I got the double free report:
BUG: KASAN: double-free or invalid-free in kfree+0xce/0x390
iio_device_unregister_sysfs+0x108/0x13b [industrialio]
iio_dev_release+0x9e/0x10e [industrialio]
device_release+0xa5/0x240
If __iio_device_register() fails, iio_dev_opaque->groups will be freed
in error path in iio_device_unregister_sysfs(), then iio_dev_release()
will call iio_device_unregister_sysfs() again, it causes double free.
Set iio_dev_opaque->groups to NULL when it's freed to fix this double free.
Not this is a local work around for a more general mess around life time
management that will get cleaned up and should make this handling
unnecesarry.
Fixes: 32f171724e5c ("iio: core: rework iio device group creation")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211013030532.956133-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
I got a null-ptr-deref report when doing fault injection test:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:strlen+0x0/0x20
Call Trace:
start_creating+0x199/0x2f0
debugfs_create_dir+0x25/0x430
__iio_device_register+0x4da/0x1b40 [industrialio]
__devm_iio_device_register+0x22/0x80 [industrialio]
max1027_probe+0x639/0x860 [max1027]
spi_probe+0x183/0x210
really_probe+0x285/0xc30
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e553f182d55b ("staging: iio: core: Introduce debugfs support...")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211012063624.3167460-1-yangyingliang@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
If the second iio_device_register_sysfs_group() fails,
'legacy_buffer_group.attrs' need be freed too or it will
cause memory leak:
unreferenced object 0xffff888003618280 (size 64):
comm "xrun", pid 357, jiffies 4294907259 (age 22.296s)
hex dump (first 32 bytes):
80 f6 8c 03 80 88 ff ff 80 fb 8c 03 80 88 ff ff ................
00 f9 8c 03 80 88 ff ff 80 fc 8c 03 80 88 ff ff ................
backtrace:
[<00000000076bfd43>] __kmalloc+0x1a3/0x2f0
[<00000000c32e4886>] iio_buffers_alloc_sysfs_and_mask+0xc31/0x1290 [industrialio]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: d9a625744ed0 ("iio: core: merge buffer/ & scan_elements/ attributes")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211013144242.1685060-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When __iio_buffer_alloc_sysfs_and_mask() failed, 'unwind_idx' should be
set to 'i - 1' to prevent double-free when cleanup resources.
BUG: KASAN: double-free or invalid-free in __iio_buffer_free_sysfs_and_mask+0x32/0xb0 [industrialio]
Call Trace:
kfree+0x117/0x4c0
__iio_buffer_free_sysfs_and_mask+0x32/0xb0 [industrialio]
iio_buffers_alloc_sysfs_and_mask+0x60d/0x1570 [industrialio]
__iio_device_register+0x483/0x1a30 [industrialio]
ina2xx_probe+0x625/0x980 [ina2xx_adc]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ee708e6baacd ("iio: buffer: introduce support for attaching more IIO buffers")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211013094923.2473-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
When iio_buffer_wrap_attr() returns NULL or buffer->buffer_group.name alloc
fails, the 'attr' which is allocated in __iio_buffer_alloc_sysfs_and_mask()
is not freed, and cause memory leak.
unreferenced object 0xffff888014882a00 (size 64):
comm "i2c-adjd_s311-8", pid 424, jiffies 4294907737 (age 44.396s)
hex dump (first 32 bytes):
00 0f 8a 15 80 88 ff ff 00 0e 8a 15 80 88 ff ff ................
80 04 8a 15 80 88 ff ff 80 05 8a 15 80 88 ff ff ................
backtrace:
[<0000000021752e67>] __kmalloc+0x1af/0x3c0
[<0000000043e8305c>] iio_buffers_alloc_sysfs_and_mask+0xe73/0x1570 [industrialio]
[<00000000b7aa5a17>] __iio_device_register+0x483/0x1a30 [industrialio]
[<000000003fa0fb2f>] __devm_iio_device_register+0x23/0x90 [industrialio]
[<000000003ab040cf>] adjd_s311_probe+0x19c/0x200 [adjd_s311]
[<0000000080458969>] i2c_device_probe+0xa31/0xbe0
[<00000000e20678ad>] really_probe+0x299/0xc30
[<000000006bea9b27>] __driver_probe_device+0x357/0x500
[<00000000e1df10d4>] driver_probe_device+0x4e/0x140
[<0000000003661beb>] __device_attach_driver+0x257/0x340
[<000000005bb4aa26>] bus_for_each_drv+0x166/0x1e0
[<00000000272c5236>] __device_attach+0x272/0x420
[<00000000d52a96ae>] bus_probe_device+0x1eb/0x2a0
[<00000000129f7737>] device_add+0xbf0/0x1f90
[<000000005eed4e52>] i2c_new_client_device+0x622/0xb20
[<00000000b85a9c43>] new_device_store+0x1fa/0x420
This patch fix to free it before the error return.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 15097c7a1adc ("iio: buffer: wrap all buffer attributes into iio_dev_attr")
Fixes: d9a625744ed0 ("iio: core: merge buffer/ & scan_elements/ attributes")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211013094343.315275-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Check return value of kstrdup_const() in iio_buffer_wrap_attr(),
or it will cause null-ptr-deref in kernfs_name_hash() when calling
device_add() as follows:
BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:strlen+0x0/0x20
Call Trace:
kernfs_name_hash+0x22/0x110
kernfs_find_ns+0x11d/0x390
kernfs_remove_by_name_ns+0x3b/0xb0
remove_files.isra.1+0x7b/0x190
internal_create_group+0x7f1/0xbb0
internal_create_groups+0xa3/0x150
device_add+0x8f0/0x2020
cdev_device_add+0xc3/0x160
__iio_device_register+0x1427/0x1b40 [industrialio]
__devm_iio_device_register+0x22/0x80 [industrialio]
adjd_s311_probe+0x195/0x200 [adjd_s311]
i2c_device_probe+0xa07/0xbb0
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 15097c7a1adc ("iio: buffer: wrap all buffer attributes into iio_dev_attr")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211013040438.1689277-1-yangyingliang@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
As with commit 8b52d8be86d72308 ("loop: reorder loop_exit"),
unregister_blkdev() needs to be called first in order to avoid calling
brd_alloc() from brd_probe() after brd_del_one() from brd_exit(). Then,
we can avoid holding global mutex during add_disk()/del_gendisk() as with
commit 1c500ad706383f1a ("loop: reduce the loop_ctl_mutex scope").
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/e205f13d-18ff-a49c-0988-7de6ea5ff823@i-love.sakura.ne.jp
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
On success i2c_master_send() returns the number of bytes written. The
call from iio_write_channel_info(), however, expects the return value to
be zero on success.
This bug causes incorrect consumption of the sysfs buffer in
iio_write_channel_info(). When writing more than two characters to
out_voltage0_raw, the ad5446 write handler is called multiple times
causing unexpected behavior.
Fixes: 3ec36a2cf0d5 ("iio:ad5446: Add support for I2C based DACs")
Signed-off-by: Pekka Korpinen <pekka.korpinen@iki.fi>
Link: https://lore.kernel.org/r/20210929185755.2384-1-pekka.korpinen@iki.fi
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210924133515.112357-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105631.1474-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
devm_platform_ioremap_resource()
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210908105638.1525-1-caihuoqing@baidu.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
