| Age | Commit message (Collapse) | Author |
|---|
|
Undo a feature introduced in v3.14 by commit fcd46b34425d
"firewire: Enable remote DMA above 4 GB". That change raised the
minimum address at which protocol drivers and user programs can register
for request reception from 0x0001'0000'0000 to 0x8000'0000'0000.
It turned out that at least one vendor-specific protocol exists which
uses lower addresses: https://bugzilla.kernel.org/show_bug.cgi?id=76921
For the time being, revert most of commit fcd46b34425d so that affected
protocols work like with kernel v3.13 and before. Just keep the valid
documentation parts from the regressing commit, and the ability to
identify controllers which could be programmed to accept >32 bit
physical DMA addresses. The rest of fcd46b34425d should probably be
brought back as an optional instead of default feature.
Reported-by: Fabien Spindler <fabien.spindler@inria.fr>
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
mips-for-linux-next
|
|
As long as the Firmware isn't reporting a higher API major version number
than what the driver knows about, the driver does not need to worry as
much about greater minor numbers. The API changes minor numbers when
things get added to the API, but no existing structs or calls are changed.
The driver has the option of warning that the minor numbers don't match.
This will allow a little more flexibility in handling newer NICs and NVMs
in the field.
Change-ID: I5302acd2d147a2992328991ee7223b2ff39c8741
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The RESETTING state means that a Catastrophic Hardware Bad Thing is
happening and the driver need to tiptoe around and not use the admin
queue or registers or anything like that.
On the other hand, a reinit is no big deal and we can use the admin
queue, and we should. So don't set the state to RESETTING here.
This fixes a Tx hang and FW crash that happens after setting the MTU on
a VF.
Change-ID: I3e6191edbd6a93958a1f1bd1d41a5c2d17474d41
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently FCoE is not supported with MFP modes, so this patch
makes sure it is disabled.
It is disabled by overriding HW FCoE capability, so that later
it can be re-enabled by just the SW upgrade.
Change-ID: I1c0bae5c099b209f56b88bda360031a8565e43e8
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-By: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the clear_pxe AdminQ API call.
Change-ID: Ia770ff3404971bb3889b53a39c3a7bfaf3f4d399
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
If pf_reset failed, it becomes necessary to clear recovery pending bit, instead
of falling through the setup process.
Change-ID: Ic1611e6a32741fe3a2782ec7be173cb65e7492ed
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
|
|
tx_lpi_status and rx_lpi_status are declared as bool but then used in sizeof
operations in the CORE driver code. Make them u32 to make sparse be quiet.
Change-ID: Iad6daeb1c7149e61ece242acd18c64b320c246a3
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The storm control features are not part of the hardware
and mistakenly were left in the code. Remove them as
they are not needed any more.
Change-ID: I6e9277c8da2c52e69348a657bae25271449c2099
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We have a function to calculate this, so update the code to use the function.
Change-ID: Ia345b6fe6ec7f0b2dcf1199471b0d0f959ad3908
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Based on review feedback from upstream cmd->data is not
defined in ETHTOOL_GRXCLSRULE but needs to be reported in
ETHTOOL_GRXCLSRLCNT. Also use a helper function to calculate the total
filter count.
Change-ID: Iaacbf729527b73290c4fdad837b379b44fd7dd20
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Patch to remove PCTYPE definitions which are now reserved.
Change-ID: I66c1c16a45a16f4894b2983101ab2a48ce03f1f4
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes the declaration of Tx/Rx rings inside several loops. It
eliminates declaring the same rings every time for the duration of the loop,
instead declaring them once before the loop.
Change-ID: I59dea54276f18c47dca522f520c18f65fe42a15d
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In order for the VF to achieve its programmed Tx rate, we need to set
the max credits value to 4. While we're at it, get rid of some magic
numbers.
Change-ID: I4f17b4d3a90f1e069bdd134a543f0aa22feac3a9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Because the hardware configures VF Tx rates in increments of 50 Mbps,
values smaller than that would be rounded down to 0, which was
interpreted as no limit at all. Rather than do this, we round up to 50
Mbps and notify the user.
Change-ID: I5275848233fe7514cf93e11323661c68f4c38737
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
As recommended by the hardware guys, enable descriptor prefetch for
rings belonging to VFs. This matches a change already made for ring
belonging to the PF.
Change-ID: Idcc4dc7064bc9144ea81f5701ad07b7ecd11ba49
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Update the i40e_check_asq_alive check to ensure that the len register
offset is non-zero, indicating that SW has initialized the AQ.
Change-ID: I9c2e804788b4775bef9c7e80954ab004e6bdb306
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds pin definitiones for the MSM8x74 TLMM.
New definitions include:
BLSP devices (I2C, UART, SPI, and UIM), mi2s, gp clk,
pdm, gcc clk, cci_timer, cci_i2c, cam_clk, hsic, tsif,
sdc3, sdc4, and other assorted pins.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-By: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Drop underscore in spdif_groups to match all other groups.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is unused since all users (OMAP4/5) are DT only.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
'cma: Remove potential deadlock situation' introduces per cma area mutex
for bitmap management. It is good, but there is one mistake. When we
can't find appropriate area in bitmap, we release cma_mutex global lock
rather than cma->lock and this is a bug. So fix it.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
|
|
New Cintiq tablets have a 200 tablet counts outside of screen area.
Add x/y_min for ABS_X/Y to pass this information to userland.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds DT support to the tsc2005 touchscreen driver. It also adds
regulator support to the driver if booted via DT.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add common DT binding documentation for touchscreen devices and
implement input_parse_touchscreen_of_params, which parses the common
properties and configures the input device accordingly.
The method currently does not interpret the axis inversion properties,
since there is no matching flag in the generic linux input device.
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The stripe cache has two goals:
1. cache data, so next time if data can be found in stripe cache, disk access
can be avoided.
2. stable data. data is copied from bio to stripe cache and calculated parity.
data written to disk is from stripe cache, so if upper layer changes bio data,
data written to disk isn't impacted.
In my environment, I can guarantee 2 will not happen. And BDI_CAP_STABLE_WRITES
can guarantee 2 too. For 1, it's not common too. block plug mechanism will
dispatch a bunch of sequentail small requests together. And since I'm using
SSD, I'm using small chunk size. It's rare case stripe cache is really useful.
So I'd like to avoid the copy from bio to stripe cache and it's very helpful
for performance. In my 1M randwrite tests, avoid the copy can increase the
performance more than 30%.
Of course, this shouldn't be enabled by default. It's reported enabling
BDI_CAP_STABLE_WRITES can harm some workloads before, so I added an option to
control it.
Neilb:
changed BUG_ON to WARN_ON
Removed some assignments from raid5_build_block which are now not needed.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
file_page_index(store, 0) is *always* 0.
This is because the bitmap sb, at 256 bytes, is *always* less than
one page.
So subtracting it has no effect and the code should be removed.
Reported-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The (lockless) release_list reduces lock contention, but there is excessive
queueing and dequeuing of stripes on this list. A stripe will currently be
queued on the release_list with a stripe reference count > 1. This can cause
the raid5 kernel thread(s) to dequeue the stripe and decrement the refcount
without doing any other useful processing of the stripe. The are two cases
when the stripe can be put on the release_list multiple times before it is
actually handled by the kernel thread(s).
1) make_request() activates the stripe processing in 4k increments. When a
write request is large enough to span multiple chunks of a stripe_head, the
first 4k chunk adds the stripe to the plug list. The next 4k chunk that is
processed for the same stripe puts the stripe on the release_list with a
refcount=2. This can cause the kernel thread to process and decrement the
stripe before the stripe us unplugged, which again will put it back on the
release_list.
2) Whenever IO is scheduled on a stripe (pre-read and/or write), the stripe
refcount is set to the number of active IO (for each chunk). The stripe is
released as each IO complete, and can be queued and dequeued multiple times
on the release_list, until its refcount finally reached zero.
This simple patch will ensure a stripe is only queued on the release_list when
its refcount=1 and is ready to be handled by the kernel thread(s). I added some
instrumentation to raid5 and counted the number of times striped were queued on
the release_list for a variety of write IO sizes. Without this patch the number
of times stripes got queued on the release_list was 100-500% higher than with
the patch. The excess queuing will increase with the IO size. The patch also
improved throughput by 5-10%.
Signed-off-by: Eivind Sarto <esarto@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Julia Lawall and coccinelle report that md_clear_badblocks always
returns 0, despite appearing to have an error path.
The error path really should return an error code. ENOSPC is
reasonably appropriate.
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If it is found that we need to pre-read some blocks before a write
can succeed, we normally set STRIPE_DELAYED and don't actually perform
the read until STRIPE_PREREAD_ACTIVE subsequently gets set.
However for a degraded RAID6 we currently perform the reads as soon
as we see that a write is pending. This significantly hurts
throughput.
So:
- when handle_stripe_dirtying find a block that it wants on a device
that is failed, set STRIPE_DELAY, instead of doing nothing, and
- when fetch_block detects that a read might be required to satisfy a
write, only perform the read if STRIPE_PREREAD_ACTIVE is set,
and if we would actually need to read something to complete the write.
This also helps RAID5, though less often as RAID5 supports a
read-modify-write cycle. For RAID5 the read is performed too early
only if the write is not a full 4K aligned write (i.e. no an
R5_OVERWRITE).
Also clean up a couple of horrible bits of formatting.
Reported-by: Patrik Horník <patrik@dsl.sk>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
read-only arrays should not be changed. This includes changing
the level, layout, size, or number of devices.
So reject those changes for readonly arrays.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Commit 8313b8e57f55b15e5b7f7fc5d1630bbf686a9a97
md: fix problem when adding device to read-only array with bitmap.
added a called to md_reap_sync_thread() which cause a reshape thread
to be interrupted (in particular, it could cause md_thread() to never even
call md_do_sync()).
However it didn't set MD_RECOVERY_INTR so ->finish_reshape() would not
know that the reshape didn't complete.
This only happens when mddev->ro is set and normally reshape threads
don't run in that situation. But raid5 and raid10 can start a reshape
thread during "run" is the array is in the middle of a reshape.
They do this even if ->ro is set.
So it is best to set MD_RECOVERY_INTR before abortingg the
sync thread, just in case.
Though it rare for this to trigger a problem it can cause data corruption
because the reshape isn't finished properly.
So it is suitable for any stable which the offending commit was applied to.
(3.2 or later)
Fixes: 8313b8e57f55b15e5b7f7fc5d1630bbf686a9a97
Cc: stable@vger.kernel.org (3.2+)
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify error
handling and allows us to get rid of da9034_touch_remove().
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch fix a typo error in MELFAS MCS-5000 controller driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch fix a typo error in mms114 touchscreen driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch fix a typo error in MELFAS 5000/5080 controller driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
input.h was included twice.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Handling calls to ->target_index() has got complex over time and might become
more complex. So, its better to take target_index() bits out in another routine
__target_index() for better code readability. Shouldn't have any functional
impact.
Tested-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The gpmi's IP for imx6sx is nearly the same as the gpmi's IP for imx6q,
except the following two new features:
(1) the new BCH contoller has 62-BIT correcting ECC strength
(The BCH for imx6q only has 40-BIT ECC strength).
(2) add the hardware Randomizer support.
This patch does the follow changes:
(1) add a new macro GPMI_IS_MX6SX to represent the imx6sx's gpmi.
(2) add a new macro GPMI_IS_MX6.
We use this macro to initialize the same registers for both
imx6sx and imx6q, and so on.
(3) add a new gpmi_devdata instance, the gpmi_devdata_imx6sx, for
imx6sx.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
* pci/misc:
PCI: Fix return value from pci_user_{read,write}_config_*()
PCI: Turn pcibios_penalize_isa_irq() into a weak function
PCI: Test for std config alias when testing extended config space
|
