| Age | Commit message (Collapse) | Author |
|---|
|
The E800 series hardware uses the same iAVF driver as older devices,
including the virtchnl negotiation scheme.
This negotiation scheme includes a mechanism to determine what type of RSS
should be supported, including RSS over PF virtchnl messages, RSS over
firmware AdminQ messages, and RSS via direct register access.
The PF driver will always prefer VIRTCHNL_VF_OFFLOAD_RSS_PF if its
supported by the VF driver. However, if an older VF driver is loaded, it
may request only VIRTCHNL_VF_OFFLOAD_RSS_REG or VIRTCHNL_VF_OFFLOAD_RSS_AQ.
The ice driver happily agrees to support these methods. Unfortunately, the
underlying hardware does not support these mechanisms. The E800 series VFs
don't have the appropriate registers for RSS_REG. The mailbox queue used by
VFs for VF to PF communication blocks messages which do not have the
VF-to-PF opcode.
Stop lying to the VF that it could support RSS over AdminQ or registers, as
these interfaces do not work when the hardware is operating on an E800
series device.
In practice this is unlikely to be hit by any normal user. The iAVF driver
has supported RSS over PF virtchnl commands since 2016, and always defaults
to using RSS_PF if possible.
In principle, nothing actually stops the existing VF from attempting to
access the registers or send an AQ command. However a properly coded VF
will check the capability flags and will report a more useful error if it
detects a case where the driver does not support the RSS offloads that it
does.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Alan Brady <alan.brady@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix softirq's not being handled during napi_schedule() call when
receiving marker packets for queue disable by disabling local bottom
half.
The issue can be seen on ifdown:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Using ftrace to catch the failing scenario:
ifconfig [003] d.... 22739.830624: softirq_raise: vec=3 [action=NET_RX]
<idle>-0 [003] ..s.. 22739.831357: softirq_entry: vec=3 [action=NET_RX]
No interrupt and CPU is idle.
After the patch when disabling local BH before calling napi_schedule:
ifconfig [003] d.... 22993.928336: softirq_raise: vec=3 [action=NET_RX]
ifconfig [003] ..s1. 22993.928337: softirq_entry: vec=3 [action=NET_RX]
Fixes: c2d548cad150 ("idpf: add TX splitq napi poll support")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alan Brady <alan.brady@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
total_fa_cnt is supposed to include cck_fa_cnt and ofdm_fa_cnt, not just
ofdm_fa_cnt.
Fixes: 960361238b86 ("rtw88: 8821c: add false alarm statistics")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f3cb6d17-e4e4-44a7-9c9b-72aed994b5c9@gmail.com
|
|
Tenda U9 V2.0, which contains RTL8811CU, is practically unusable because
of frequent disconnections:
Feb 23 14:46:45 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:46 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:46:52 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:46:54 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:46:55 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
Feb 23 14:47:01 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-CONNECTED
- Connection to 90:55:de:__:__:__ completed [id=0 id_str=]
Feb 23 14:47:04 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-BEACON-LOSS
Feb 23 14:47:05 ideapad2 wpa_supplicant[427]: wlp3s0f3u2: CTRL-EVENT-DISCONNECTED
bssid=90:55:de:__:__:__ reason=4 locally_generated=1
This is caused by a mistake in the chip initialisation. This version of
the chip requires loading an extra AGC table right after the main one,
but the extra table is being loaded at the wrong time, in
rtw_chip_board_info_setup().
Move the extra AGC table loading to the right place, in
rtw_phy_load_tables().
The rtw_chip_board_info_setup() can only do "software" things, and
rtw_phy_load_tables() can really do IO.
Fixes: 5d6651fe8583 ("rtw88: 8821c: support RFE type2 wifi NIC")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/276c31d8-b9a8-4e54-a3ac-09b74657aff7@gmail.com
|
|
Clear bit 8 of REG_SYS_STATUS1 after MAC power on.
Without this, some RTL8821CU and RTL8811CU cannot connect to any
network:
Feb 19 13:33:11 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 1/3)
Feb 19 13:33:13 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 2/3)
Feb 19 13:33:14 ideapad2 kernel: wlp3s0f3u2: send auth to
90:55:de:__:__:__ (try 3/3)
Feb 19 13:33:15 ideapad2 kernel: wlp3s0f3u2: authentication with
90:55:de:__:__:__ timed out
The RTL8822CU and RTL8822BU out-of-tree drivers do this as well, so do
it for all three types of chips.
Tested with RTL8811CU (Tenda U9 V2.0).
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/aeeefad9-27c8-4506-a510-ef9a9a8731a4@gmail.com
|
|
RTL8822CU, RTL8822BU, and RTL8821CU need an extra register write after
reading and writing certain addresses.
Without this, the firmware upload fails approximately more than 50% of
the time.
Tested with RTL8811CU (Tenda U9 V2.0) which is the same as RTL8821CU
but without Bluetooth.
Fixes: a82dfd33d123 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/f12ed39d-28e8-4b8b-8d22-447bcf295afc@gmail.com
|
|
Add VID/PIDs that are known to be missing for this driver.
Removed /* 8811CU */ and /* 8821CU */ as they are redundant
since the file is specific to those chips.
Removed /* TOTOLINK A650UA v3 */ as the manufacturer. It has a REALTEK
VID so it may not be specific to this adapter.
Verified and tested.
Cc: stable@vger.kernel.org
Signed-off-by: Nick Morrow <morrownr@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/4ume7mjw63u7.XlMUvUuacW2ErhOCdqlLkw2@1EHFQ.trk.elasticemail.com
|
|
On a PC Engines APU our admins are faced with:
$ dmesg | grep -c "gpio-keys-polled gpio-keys-polled: unable to claim gpio 0, err=-517"
261
Such a message always appears when e.g. a new USB device is plugged in.
Suppress this message which considerably clutters the kernel log for
EPROBE_DEFER (i.e. -517).
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20240305101042.10953-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This patch intended to fix an well-knonw issue in old drivers where the
endpoint type is taken for granted, which is often triggered by fuzzers.
That was the case for this driver [1], and although the fix seems to be
correct, it uncovered another issue that leads to a regression [2], if
the endpoints of the current interface are checked.
The driver makes use of endpoints that belong to a different interface
rather than the one it binds (it binds to the third interface, but also
accesses an endpoint from a different one). The driver should claim the
interfaces it requires, but that is still not the case.
Given that the regression is more severe than the issue found by
syzkaller, the best approach is reverting the patch that causes the
regression, and trying to fix the underlying problem before checking
the endpoint types again.
Note that reverting this patch will probably trigger the syzkaller bug
at some point.
This reverts commit 2b9c3eb32a699acdd4784d6b93743271b4970899.
Link: https://syzkaller.appspot.com/bug?extid=348331f63b034f89b622 [1]
Link: https://lore.kernel.org/linux-input/87sf161jjc.wl-tiwai@suse.de/ [2]
Fixes: 2b9c3eb32a69 ("Input: bcm5974 - check endpoint type before starting traffic")
Reported-by: Jacopo Radice <jacopo.radice@outlook.com>
Closes: https://bugzilla.suse.com/show_bug.cgi?id=1220030
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240305-revert_bcm5974_ep_check-v3-1-527198cf6499@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Even though the UDL driver converts to RGB565 internally (see
pixel32_to_be16() in udl_transfer.c), it advertises XRGB8888 for
compatibility. Let's add ARGB8888 to that list.
This makes UDL devices work on ChromeOS again after commit
c91acda3a380 ("drm/gem: Check for valid formats"). Prior to that
commit things were "working" because we'd silently treat the ARGB8888
that ChromeOS wanted as XRGB8888.
Fixes: c91acda3a380 ("drm/gem: Check for valid formats")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240227141928.1.I24ac8d51544e4624b7e9d438d95880c4283e611b@changeid
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the fcloop_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the nvmf_class structure to be declared at build time
placing it into read-only memory, instead of having to be dynamically
allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Since commit 43a7206b0963 ("driver core: class: make class_register() take
a const *"), the driver core allows for struct class to be in read-only
memory, so move the structures nvme_class, nvme_subsys_class and
nvme_ns_chr_class to be declared at build time placing them into read-only
memory, instead of having to be dynamically allocated at boot time.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ricardo B. Marliere <ricardo@marliere.net>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
On Arrow Lake S systems, MEI is no longer strictly connected to bus 0,
while graphics remain exclusively on bus 0. Adapt the component
matching logic to accommodate this change:
Original behavior: Required both MEI and graphics to be on the same
bus 0.
New behavior: Only enforces graphics to be on bus 0 (integrated),
allowing MEI to reside on any bus.
This ensures compatibility with Arrow Lake S and maintains functionality
for the legacy systems.
Fixes: 1dd924f6885b ("mei: gsc_proxy: add gsc proxy driver")
Cc: stable@vger.kernel.org # v6.3+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20240220200020.231192-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For CMA memory allocation, ownership is assigned to DSP to make it
accessible by the PD running on the DSP. With current implementation
HLOS VM is stored in the channel structure during rpmsg_probe and
this VM is passed to qcom_scm call as the source VM.
The qcom_scm call will overwrite the passed source VM with the next
VM which would cause a problem in case the scm call is again needed.
Adding a local copy of source VM whereever scm call is made to avoid
this problem.
Fixes: 0871561055e6 ("misc: fastrpc: Add support for audiopd")
Cc: stable <stable@kernel.org>
Signed-off-by: Ekansh Gupta <quic_ekangupt@quicinc.com>
Reviewed-by: Elliot Berman <quic_eberman@quicinc.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20240224114247.85953-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The comedi_test devices have a couple of timers (ai_timer and ao_timer)
that can be started to simulate hardware interrupts. Their expiry
functions normally reschedule the timer. The driver code calls either
del_timer_sync() or del_timer() to delete the timers from the queue, but
does not currently prevent the timers from rescheduling themselves so
synchronized deletion may be ineffective.
Add a couple of boolean members (one for each timer: ai_timer_enable and
ao_timer_enable) to the device private data structure to indicate
whether the timers are allowed to reschedule themselves. Set the member
to true when adding the timer to the queue, and to false when deleting
the timer from the queue in the waveform_ai_cancel() and
waveform_ao_cancel() functions.
The del_timer_sync() function is also called from the waveform_detach()
function, but the timer enable members will already be set to false when
that function is called, so no change is needed there.
Fixes: 403fe7f34e33 ("staging: comedi: comedi_test: fix timer race conditions")
Cc: stable@vger.kernel.org # 4.4+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20240214100747.16203-1-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The refactoring done in commit 5c57b1ccecc7 ("comedi: comedi_8255: Rework
subdevice initialization functions") to the initialization of the io
field of struct subdev_8255_private broke all cards using the
drivers/comedi/drivers/comedi_8255.c module.
Prior to 5c57b1ccecc7, __subdev_8255_init() initialized the io field
in the newly allocated struct subdev_8255_private to the non-NULL
callback given to the function, otherwise it used a flag parameter to
select between subdev_8255_mmio and subdev_8255_io. The refactoring
removed that logic and the flag, as subdev_8255_mm_init() and
subdev_8255_io_init() now explicitly pass subdev_8255_mmio and
subdev_8255_io respectively to __subdev_8255_init(), only
__subdev_8255_init() never sets spriv->io to the supplied
callback. That spriv->io is NULL leads to a later BUG:
BUG: kernel NULL pointer dereference, address: 0000000000000000
PGD 0 P4D 0
Oops: 0010 [#1] SMP PTI
CPU: 1 PID: 1210 Comm: systemd-udevd Not tainted 6.7.3-x86_64 #1
Hardware name: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
RIP: 0010:0x0
Code: Unable to access opcode bytes at 0xffffffffffffffd6.
RSP: 0018:ffffa3f1c02d7b78 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff91f847aefd00 RCX: 000000000000009b
RDX: 0000000000000003 RSI: 0000000000000001 RDI: ffff91f840f6fc00
RBP: ffff91f840f6fc00 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 000000000000005f R12: 0000000000000000
R13: 0000000000000000 R14: ffffffffc0102498 R15: ffff91f847ce6ba8
FS: 00007f72f4e8f500(0000) GS:ffff91f8d5c80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 000000010540e000 CR4: 00000000000406f0
Call Trace:
<TASK>
? __die_body+0x15/0x57
? page_fault_oops+0x2ef/0x33c
? insert_vmap_area.constprop.0+0xb6/0xd5
? alloc_vmap_area+0x529/0x5ee
? exc_page_fault+0x15a/0x489
? asm_exc_page_fault+0x22/0x30
__subdev_8255_init+0x79/0x8d [comedi_8255]
pci_8255_auto_attach+0x11a/0x139 [8255_pci]
comedi_auto_config+0xac/0x117 [comedi]
? __pfx___driver_attach+0x10/0x10
pci_device_probe+0x88/0xf9
really_probe+0x101/0x248
__driver_probe_device+0xbb/0xed
driver_probe_device+0x1a/0x72
__driver_attach+0xd4/0xed
bus_for_each_dev+0x76/0xb8
bus_add_driver+0xbe/0x1be
driver_register+0x9a/0xd8
comedi_pci_driver_register+0x28/0x48 [comedi_pci]
? __pfx_pci_8255_driver_init+0x10/0x10 [8255_pci]
do_one_initcall+0x72/0x183
do_init_module+0x5b/0x1e8
init_module_from_file+0x86/0xac
__do_sys_finit_module+0x151/0x218
do_syscall_64+0x72/0xdb
entry_SYSCALL_64_after_hwframe+0x6e/0x76
RIP: 0033:0x7f72f50a0cb9
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 47 71 0c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffd47e512d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 0000562dd06ae070 RCX: 00007f72f50a0cb9
RDX: 0000000000000000 RSI: 00007f72f52d32df RDI: 000000000000000e
RBP: 0000000000000000 R08: 00007f72f5168b20 R09: 0000000000000000
R10: 0000000000000050 R11: 0000000000000246 R12: 00007f72f52d32df
R13: 0000000000020000 R14: 0000562dd06785c0 R15: 0000562dcfd0e9a8
</TASK>
Modules linked in: 8255_pci(+) comedi_8255 comedi_pci comedi intel_gtt e100(+) acpi_cpufreq rtc_cmos usbhid
CR2: 0000000000000000
---[ end trace 0000000000000000 ]---
RIP: 0010:0x0
Code: Unable to access opcode bytes at 0xffffffffffffffd6.
RSP: 0018:ffffa3f1c02d7b78 EFLAGS: 00010202
RAX: 0000000000000000 RBX: ffff91f847aefd00 RCX: 000000000000009b
RDX: 0000000000000003 RSI: 0000000000000001 RDI: ffff91f840f6fc00
RBP: ffff91f840f6fc00 R08: 0000000000000000 R09: 0000000000000001
R10: 0000000000000000 R11: 000000000000005f R12: 0000000000000000
R13: 0000000000000000 R14: ffffffffc0102498 R15: ffff91f847ce6ba8
FS: 00007f72f4e8f500(0000) GS:ffff91f8d5c80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffffffffd6 CR3: 000000010540e000 CR4: 00000000000406f0
This patch simply corrects the above mistake by initializing spriv->io
to the given io callback.
Fixes: 5c57b1ccecc7 ("comedi: comedi_8255: Rework subdevice initialization functions")
Signed-off-by: Frej Drejhammar <frej.drejhammar@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Ian Abbott <abbotti@mev.co.uk>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20240211175822.1357-1-frej.drejhammar@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If VM_BIND is enabled on the client the legacy submission ioctl can't be
used, however if a client tries to do so regardless it will return an
error. In this case the clients mutex remained unlocked leading to a
deadlock inside nouveau_drm_postclose or any other nouveau ioctl call.
Fixes: b88baab82871 ("drm/nouveau: implement new VM_BIND uAPI")
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: <stable@vger.kernel.org> # v6.6+
Signed-off-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Danilo Krummrich <dakr@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240305133853.2214268-1-kherbst@redhat.com
|
|
Ring expansion checker may incorrectly assume a completely full ring
is empty, missing the need for expansion.
This is due to a special empty ring case where the dequeue ends up
ahead of the enqueue pointer. This is seen when enqueued TRBs fill up
exactly a segment, with enqueue then pointing to the end link TRB.
Once those TRBs are handled the dequeue pointer will follow the link
TRB and end up pointing to the first entry on the next segment, past
the enqueue.
This same enqueue - dequeue condition can be true if a ring is full,
with enqueue ending on that last link TRB before the dequeue pointer
on the next segment.
This can be seen when queuing several ~510 small URBs via usbfs in
one go before a single one is handled (i.e. dequeue not moved from first
entry in segment).
Expand the ring already when enqueue reaches the link TRB before the
dequeue segment, instead of expanding it when enqueue moves into the
dequeue segment.
Reported-by: Chris Yokum <linux-usb@mail.totalphase.com>
Closes: https://lore.kernel.org/all/949223224.833962.1709339266739.JavaMail.zimbra@totalphase.com
Tested-by: Chris Yokum <linux-usb@mail.totalphase.com>
Fixes: f5af638f0609 ("xhci: Fix transfer ring expansion size calculation")
Cc: stable@vger.kernel.org # v6.5+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240305132312.955171-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 5c7e105cd156fc9adf5294a83623d7a40c15f9b9.
As identified by KASAN, the simplification done by the cleanup patch
was not legal.
>From tracing through the code, it can be seen that we're transmitting
from a 4096-byte circular buffer. We copy anywhere from 1-4 bytes from
it each time. The simplification runs into trouble when we get near
the end of the circular buffer. For instance, we might start out with
xmit->tail = 4094 and we want to transfer 4 bytes. With the code
before simplification this was no problem. We'd read buf[4094],
buf[4095], buf[0], and buf[1]. With the new code we'll do a
memcpy(&buf[4094], 4) which reads 2 bytes past the end of the buffer
and then skips transmitting what's at buf[0] and buf[1].
KASAN isn't 100% consistent at reporting this for me, but to be extra
confident in the analysis, I added traces of the tail and tx_bytes and
then wrote a test program:
while true; do
echo -n "abcdefghijklmnopqrstuvwxyz0" > /dev/ttyMSM0
sleep .1
done
I watched the traces over SSH and saw:
qcom_geni_serial_send_chunk_fifo: 4093 4
qcom_geni_serial_send_chunk_fifo: 1 3
Which indicated that one byte should be missing. Sure enough the
output that should have been:
abcdefghijklmnopqrstuvwxyz0
In one case was actually missing a byte:
abcdefghijklmnopqrstuvwyz0
Running "ls -al" on large directories also made the missing bytes
obvious since columns didn't line up.
While the original code may not be the most elegant, we only talking
about copying up to 4 bytes here. Let's just go back to the code that
worked.
Fixes: 5c7e105cd156 ("tty: serial: simplify qcom_geni_serial_send_chunk_fifo()")
Cc: stable <stable@kernel.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240304174952.1.I920a314049b345efd1f69d708e7f74d2213d0b49@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the remote uart device is not connected or not enabled after booting
up, the CTS line is high by default. At this time, if we enable the flow
control when opening the device(for example, using “stty -F /dev/ttyLP4
crtscts” command), there will be a pending idle preamble(first writing 0
and then writing 1 to UARTCTRL_TE will queue an idle preamble) that
cannot be sent out, resulting in the uart port fail to close(waiting for
TX empty), so the user space stty will have to wait for a long time or
forever.
This is an LPUART IP bug(idle preamble has higher priority than CTS),
here add a workaround patch to enable TX CTS after enabling UARTCTRL_TE,
so that the idle preamble does not get stuck due to CTS is deasserted.
Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20240305015706.1050769-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unused USB ports may have bogus location data in ACPI PLD tables.
This causes port peering failures as these unused USB2 and USB3 ports
location may match.
Due to these failures the driver prints a
"usb: port power management may be unreliable" warning, and
unnecessarily blocks port power off during runtime suspend.
This was debugged on a couple DELL systems where the unused ports
all returned zeroes in their location data.
Similar bugreports exist for other systems.
Don't try to peer or match ports that have connect type set to
USB_PORT_NOT_USED.
Fixes: 3bfd659baec8 ("usb: find internal hub tier mismatch via acpi")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218465
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218486
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://lore.kernel.org/linux-usb/5406d361-f5b7-4309-b0e6-8c94408f7d75@molgen.mpg.de
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218490
Link: https://lore.kernel.org/r/20240222233343.71856-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While connecting to a Linux host with CDC_NCM_NTB_DEF_SIZE_TX
set to 65536, it has been observed that we receive short packets,
which come at interval of 5-10 seconds sometimes and have block
length zero but still contain 1-2 valid datagrams present.
According to the NCM spec:
"If wBlockLength = 0x0000, the block is terminated by a
short packet. In this case, the USB transfer must still
be shorter than dwNtbInMaxSize or dwNtbOutMaxSize. If
exactly dwNtbInMaxSize or dwNtbOutMaxSize bytes are sent,
and the size is a multiple of wMaxPacketSize for the
given pipe, then no ZLP shall be sent.
wBlockLength= 0x0000 must be used with extreme care, because
of the possibility that the host and device may get out of
sync, and because of test issues.
wBlockLength = 0x0000 allows the sender to reduce latency by
starting to send a very large NTB, and then shortening it when
the sender discovers that there’s not sufficient data to justify
sending a large NTB"
However, there is a potential issue with the current implementation,
as it checks for the occurrence of multiple NTBs in a single
giveback by verifying if the leftover bytes to be processed is zero
or not. If the block length reads zero, we would process the same
NTB infintely because the leftover bytes is never zero and it leads
to a crash. Fix this by bailing out if block length reads zero.
Cc: stable@vger.kernel.org
Fixes: 427694cfaafa ("usb: gadget: ncm: Handle decoding of multiple NTB's in unwrap call")
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20240228115441.2105585-1-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
device attribute group
The DisplayPort driver's sysfs nodes may be present to the userspace before
typec_altmode_set_drvdata() completes in dp_altmode_probe. This means that
a sysfs read can trigger a NULL pointer error by deferencing dp->hpd in
hpd_show or dp->lock in pin_assignment_show, as dev_get_drvdata() returns
NULL in those cases.
Remove manual sysfs node creation in favor of adding attribute group as
default for devices bound to the driver. The ATTRIBUTE_GROUPS() macro is
not used here otherwise the path to the sysfs nodes is no longer compliant
with the ABI.
Fixes: 0e3bb7d6894d ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Link: https://lore.kernel.org/r/20240229001101.3889432-2-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While commit 69f89168b310 ("usb: typec: tpcm: Fix issues with power being
removed during reset") fixes the boot issues for bus powered devices such
as LibreTech Renegade Elite/Firefly, it trades off the CC pins NOT being
Hi-Zed during errory recovery (i.e PORT_RESET) for devices which are NOT
bus powered(a.k.a self powered). This change Hi-Zs the CC pins only for
self powered devices, thus preventing brown out for bus powered devices
Adhering to spec is gaining more importance due to the Common charger
initiative enforced by the European Union.
Quoting from the spec:
4.5.2.2.2.1 ErrorRecovery State Requirements
The port shall not drive VBUS or VCONN, and shall present a
high-impedance to ground (above zOPEN) on its CC1 and CC2 pins.
Hi-Zing the CC pins is the inteded behavior for PORT_RESET.
CC pins are set to default state after tErrorRecovery in
PORT_RESET_WAIT_OFF.
4.5.2.2.2.2 Exiting From ErrorRecovery State
A Sink shall transition to Unattached.SNK after tErrorRecovery.
A Source shall transition to Unattached.SRC after tErrorRecovery.
Fixes: 69f89168b310 ("usb: typec: tpcm: Fix issues with power being removed during reset")
Cc: stable@vger.kernel.org
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Tested-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240228000512.746252-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On SM8550 and SM8650 Qualcomm platforms a call to UCSI_GET_PDOS for
non-PD partners will cause a firmware crash with no
easy way to recover from it.
Add UCSI_NO_PARTNER_PDOS quirk for those platform until we find
a way to properly handle the crash.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20240223-topic-sm8550-upstream-ucsi-no-pdos-v1-1-8900ad510944@linaro.org
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2024-03-04
this is a pull request of 4 patches for net-next/master.
The 1st patch is by Jimmy Assarsson and adds support for the Leaf v3
to the kvaser_usb driver.
Martin Jocić's patch targets the kvaser_pciefd driver and adds support
for the Kvaser PCIe 8xCAN device.
Followed by a patch by me that adds a missing a cpu_to_le32() to the
gs_usb driver, the change is not critical as the assigned value is 0.
The last patch is also by me and replaces a literal 256 with a proper
define.
linux-can-next-for-6.9-20240304
* tag 'linux-can-next-for-6.9-20240304' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: mcp251xfd: __mcp251xfd_get_berr_counter(): use CAN_BUS_OFF_THRESHOLD instead of open coding it
can: gs_usb: gs_cmd_reset(): use cpu_to_le32() to assign mode
can: kvaser_pciefd: Add support for Kvaser PCIe 8xCAN
can: kvaser_usb: Add support for Leaf v3
====================
Link: https://lore.kernel.org/r/20240304092051.3631481-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
skb_gro_header_hard() is renamed to skb_gro_may_pull() to match
the convention used by common helpers like pskb_may_pull().
This means the condition is inverted:
if (skb_gro_header_hard(skb, hlen))
slow_path();
becomes:
if (!skb_gro_may_pull(skb, hlen))
slow_path();
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The "MT7621 Giga Switch Programming Guide v0.3", "MT7531 Reference Manual
for Development Board v1.0", and "MT7988A Wi-Fi 7 Generation Router
Platform: Datasheet (Open Version) v0.1" documents show that these bits are
enabled at reset:
PMCR_IFG_XMIT(1) (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_MAC_MODE (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_EN
PMCR_RX_EN
PMCR_BACKOFF_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_BACKPR_EN (not part of PMCR_LINK_SETTINGS_MASK)
PMCR_TX_FC_EN
PMCR_RX_FC_EN
These bits also don't exist on the MT7530_PMCR_P(6) register of the switch
on the MT7988 SoC:
PMCR_IFG_XMIT()
PMCR_MAC_MODE
PMCR_BACKOFF_EN
PMCR_BACKPR_EN
Remove the setting of the bits not part of PMCR_LINK_SETTINGS_MASK on
phylink_mac_config as they're already set.
The bit for setting the port on force mode is already done on
mt7530_setup() and mt7531_setup_common(). So get rid of
PMCR_FORCE_MODE_ID() which helped determine which bit to use for the switch
model.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
port_enable and port_disable clears the link settings. Move that to
mt7530_setup() and mt7531_setup_common() which set up the switches. This
way, the link settings are cleared on all ports at setup, and then only
once with phylink_mac_link_down() when a link goes down.
Enable force mode at setup to apply the force part of the link settings.
This ensures that disabled ports will have their link down.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The commit fae463084032 ("net: dsa: mt753x: fix pcs conversion regression")
fixes regression caused by cpu_port_config manually calling phylink
operations. cpu_port_config was deemed useless and was removed. Therefore,
put initialising PCS devices code back to its original order.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There is no need for a separate function to call
priv->info->mac_port_config(). Call it from mt753x_phylink_mac_config()
instead and remove mt753x_mac_config().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
priv->info->cpu_port_config() is used for MT7531 and the switch on the
MT7988 SoC. It sets up the ports described as a CPU port earlier than the
phylink code path would do.
This function is useless as:
- Configuring the MACs can be done from the phylink_mac_config code path
instead.
- All the link configuration it does on the CPU ports are later undone with
the port_enable, phylink_mac_config, and then phylink_mac_link_up code
path [1].
priv->p5_interface and priv->p6_interface were being used to prevent
configuring the MACs from the phylink_mac_config code path. Remove them now
that they hold no purpose.
Remove priv->info->cpu_port_config(). On mt753x_phylink_mac_config, switch
to if statements to simplify the code.
Remove the overwriting of the speed and duplex interfaces for certain
interface modes. Phylink already provides the speed and duplex variables
with proper values. Phylink already sets the max speed of TRGMII to
SPEED_1000. Add SPEED_2500 for PHY_INTERFACE_MODE_2500BASEX to where the
speed and EEE bits are set instead.
On the switch on the MT7988 SoC, PHY_INTERFACE_MODE_INTERNAL is being used
to describe the interface mode of the 10G MAC, which is of port 6. On
mt7988_cpu_port_config() PMCR_FORCE_SPEED_1000 was set via the
PMCR_CPU_PORT_SETTING() mask. Add SPEED_10000 case to where the speed bits
are set to cover this. No need to add it to where the EEE bits are set as
the "MT7988A Wi-Fi 7 Generation Router Platform: Datasheet (Open Version)
v0.1" document shows that these bits don't exist on the MT7530_PMCR_P(6)
register.
Remove the definition of PMCR_CPU_PORT_SETTING() now that it holds no
purpose.
Change mt753x_cpu_port_enable() to void now that there're no error cases
left.
Link: https://lore.kernel.org/netdev/ZHy2jQLesdYFMQtO@shell.armlinux.org.uk/ [1]
Suggested-by: Russell King (Oracle) <linux@armlinux.org.uk>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Remove error returns on the cases where they are already handled with the
function the mac_port_get_caps member in mt753x_table points to.
mt7531_mac_config() is also called from mt7531_cpu_port_config() outside of
phylink but the port and interface modes are already handled there.
Change the functions and the mac_port_config function pointer to void now
that there're no error returns anymore.
Remove mt753x_is_mac_port() that used to help the said error returns.
On mt7531_mac_config(), switch to if statements to simplify the code.
Remove internal phy cases from mt753x_phylink_mac_config(), there is no
need to check the interface mode as that's already handled with the
function the mac_port_get_caps member in mt753x_table points to.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According to the document MT7531 Reference Manual for Development Board
v1.0, the SW_PHY_RST bit on the SYS_CTRL register doesn't exist for
MT7531. This is likely why forcing link down on all ports is necessary for
MT7531.
Therefore, do not set SW_PHY_RST on mt7531_setup().
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Setting this register related to interrupts is only needed for the MT7530
switch. Make an exclusive check to ensure this.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For the switch on the MT7988 SoC, the mac_port_config member for ID_MT7988
in mt753x_table is not needed as the interfaces of all MACs are already
handled on mt7988_mac_port_get_caps().
Therefore, remove the mac_port_config member from ID_MT7988 in
mt753x_table. Before calling priv->info->mac_port_config(), if there's no
mac_port_config member in mt753x_table, exit mt753x_mac_config()
successfully.
Remove calling priv->info->mac_port_config() from the sanity check as the
sanity check requires a pointer to a mac_port_config function to be
non-NULL. This will fail for MT7988 as mac_port_config won't be a member of
its info table.
Co-developed-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The page frag in vhost_net_page_frag_refill() uses the
'struct page_frag' from skb_page_frag_refill(), but it's
implementation is similar to page_frag_alloc_align() now.
This patch removes vhost_net_page_frag_refill() by using
'struct page_frag_cache' instead of 'struct page_frag',
and allocating frag using page_frag_alloc_align().
The added benefit is that not only unifying the page frag
implementation a little, but also having about 0.5% performance
boost testing by using the vhost_net_test introduced in the
last patch.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When draining a page_frag_cache, most user are doing
the similar steps, so introduce an API to avoid code
duplication.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Currently there seems to be three page frag implementations
which all try to allocate order 3 page, if that fails, it
then fail back to allocate order 0 page, and each of them
all allow order 3 page allocation to fail under certain
condition by using specific gfp bits.
The gfp bits for order 3 page allocation are different
between different implementation, __GFP_NOMEMALLOC is
or'd to forbid access to emergency reserves memory for
__page_frag_cache_refill(), but it is not or'd in other
implementions, __GFP_DIRECT_RECLAIM is masked off to avoid
direct reclaim in vhost_net_page_frag_refill(), but it is
not masked off in __page_frag_cache_refill().
This patch unifies the gfp bits used between different
implementions by or'ing __GFP_NOMEMALLOC and masking off
__GFP_DIRECT_RECLAIM for order 3 page allocation to avoid
possible pressure for mm.
Leave the gfp unifying for page frag implementation in sock.c
for now as suggested by Paolo Abeni.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
CC: Alexander Duyck <alexander.duyck@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
GPIO EOI is not set to clear interrupt status after handling the
interrupt. It should be done in irq_chip->irq_ack, but this function
is not called in handle_nested_irq(). So executing function
txgbe_gpio_irq_ack() manually in txgbe_gpio_irq_handler().
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-2-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The register of GPIO interrupt status is masked before MAC IRQ
is enabled. This is because of hardware deficiency. So manually
clear the interrupt status before using them. Otherwise, GPIO
interrupts will never be reported again. There is a workaround for
clearing interrupts to set GPIO EOI in txgbe_up_complete().
Fixes: aefd013624a1 ("net: txgbe: use irq_domain for interrupt controller")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20240301092956.18544-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The icl+ power well code currently assumes that every AUX power
well maps to an encoder which is using said power well. That is
by no menas guaranteed as we:
- only register encoders for ports declared in the VBT
- combo PHY HDMI-only encoder no longer get an AUX CH since
commit 9856308c94ca ("drm/i915: Only populate aux_ch if really needed")
However we have places such as intel_power_domains_sanitize_state()
that blindly traverse all the possible power wells. So these bits
of code may very well encounbter an aux power well with no associated
encoder.
In this particular case the BIOS seems to have left one AUX power
well enabled even though we're dealing with a HDMI only encoder
on a combo PHY. We then proceed to turn off said power well and
explode when we can't find a matching encoder. As a short term fix
we should be able to just skip the PHY related parts of the power
well programming since we know this situation can only happen with
combo PHYs.
Another option might be to go back to always picking an AUX CH for
all encoders. However I'm a bit wary about that since we might in
theory end up conflicting with the VBT AUX CH assignment. Also
that wouldn't help with encoders not declared in the VBT, should
we ever need to poke the corresponding power wells.
Longer term we need to figure out what the actual relationship
is between the PHY vs. AUX CH vs. AUX power well. Currently this
is entirely unclear.
Cc: stable@vger.kernel.org
Fixes: 9856308c94ca ("drm/i915: Only populate aux_ch if really needed")
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10184
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240223203216.15210-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 6a8c66bf0e565c34ad0a18f820e0bb17951f7f91)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
On the error path, assign -ENOMEM to ret when memory allocation of
"dev->prev_data" fails.
Fixes: e70961505808 ("platform/x86/amd/pmf: Fixup error handling for amd_pmf_init_smart_pc()")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20240226144011.2100804-1-harshit.m.mogalapalli@oracle.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
On Goldmont p2sb_bar() only ever gets called for 2 devices, the actual P2SB
devfn 13,0 and the SPI controller which is part of the P2SB, devfn 13,2.
But the current p2sb code tries to cache BAR0 info for all of
devfn 13,0 to 13,7 . This involves calling pci_scan_single_device()
for device 13 functions 0-7 and the hw does not seem to like
pci_scan_single_device() getting called for some of the other hidden
devices. E.g. on an ASUS VivoBook D540NV-GQ065T this leads to continuous
ACPI errors leading to high CPU usage.
Fix this by only caching BAR0 info and thus only calling
pci_scan_single_device() for the P2SB and the SPI controller.
Fixes: 5913320eb0b3 ("platform/x86: p2sb: Allow p2sb_bar() calls during PCI device probe")
Reported-by: Danil Rybakov <danilrybakov249@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218531
Tested-by: Danil Rybakov <danilrybakov249@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20240304134356.305375-2-hdegoede@redhat.com
|
|
https://anongit.freedesktop.org/git/drm/drm-intel into drm-fixes
- Fix to extract HDCP information from primary connector
- Check for NULL mmu_interval_notifier before removing
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ZeGOUTfiA0_FNKLg@jlahtine-mobl.ger.corp.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2024-03-01
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2024-03-01' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: Switch to using _bh variant of of spinlock API in port timestamping NAPI poll context
net/mlx5e: Use a memory barrier to enforce PTP WQ xmit submission tracking occurs after populating the metadata_map
net/mlx5e: Fix MACsec state loss upon state update in offload path
net/mlx5e: Change the warning when ignore_flow_level is not supported
net/mlx5: Check capability for fw_reset
net/mlx5: Fix fw reporter diagnose output
net/mlx5: E-switch, Change flow rule destination checking
Revert "net/mlx5e: Check the number of elements before walk TC rhashtable"
Revert "net/mlx5: Block entering switchdev mode with ns inconsistency"
====================
Link: https://lore.kernel.org/r/20240302070318.62997-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-03-01 (ixgbe, i40e, ice)
This series contains updates to ixgbe, i40e, and ice drivers.
Maciej corrects disable flow for ixgbe, i40e, and ice drivers which could
cause non-functional interface with AF_XDP.
Michal restores host configuration when changing MSI-X count for VFs on
ice driver.
* '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: reconfig host after changing MSI-X on VF
ice: reorder disabling IRQ and NAPI in ice_qp_dis
i40e: disable NAPI right after disabling irqs when handling xsk_pool
ixgbe: {dis, en}able irqs in ixgbe_txrx_ring_{dis, en}able
====================
Link: https://lore.kernel.org/r/20240301192549.2993798-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add curly braces to avoid entering to an if statement where it is not
always required in e1000_shutdown function.
This improves code readability and might prevent non-deterministic
behaviour in the future.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-5-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When IGC is built-in but LEDS_CLASS is a loadable module, there is
a link failure:
x86_64-linux-ld: drivers/net/ethernet/intel/igc/igc_leds.o: in function `igc_led_setup':
igc_leds.c:(.text+0x75c): undefined reference to `devm_led_classdev_register_ext'
Add another dependency that prevents this combination.
Fixes: ea578703b03d ("igc: Add support for LEDs on i225/i226")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20240301184806.2634508-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
