| Age | Commit message (Collapse) | Author |
|---|
|
The video buffer used by the queue is a vb2_v4l2_buffer, not a plain
vb2_buffer. Using the wrong type causes the allocation of the buffer
storage to be too small, causing a out of bounds write when
__init_vb2_v4l2_buffer initializes the buffer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 3a762dbd5347 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191104114454.10500-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Non-TC ports always have tc_mode == TC_PORT_TBT_ALT so it was
switching aux to TBT mode for all combo-phy ports, happily this did
not caused any issue but is better follow BSpec.
Also this is reserved bit before ICL.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Fixes: e9b7e1422d40 ("drm/i915: Sanitize the terminology used for TypeC port modes")
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191029011014.286885-1-jose.souza@intel.com
(cherry picked from commit 49748264826ff4cc7f0ebbdd6b0d1a36b13b1cee)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
For the HPD interrupt functionality the HW depends on power wells in the
display core domain to be on. Accordingly when enabling these power
wells the HPD polling logic will force an HPD detection cycle to account
for hotplug events that may have happened when such a power well was
off.
Thus a detect cycle started by polling could start a new detect cycle if
a power well in the display core domain gets enabled during detect and
stays enabled after detect completes. That in turn can lead to a
detection cycle runaway.
To prevent re-triggering a poll-detect cycle make sure we drop all power
references we acquired during detect synchronously by the end of detect.
This will let the poll-detect logic continue with polling (matching the
off state of the corresponding power wells) instead of scheduling a new
detection cycle.
Fixes: 6cfe7ec02e85 ("drm/i915: Remove the unneeded AUX power ref from intel_dp_detect()")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112125
Reported-and-tested-by: Val Kulkov <val.kulkov@gmail.com>
Reported-and-tested-by: wangqr <wqr.prg@gmail.com>
Cc: Val Kulkov <val.kulkov@gmail.com>
Cc: wangqr <wqr.prg@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191028181517.22602-1-imre.deak@intel.com
(cherry picked from commit a8ddac7c9f06a12227a4f5febd1cbe0575a33179)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
error value in case of errors
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
queue overflow or OOM
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
beyond skb_queue_len_max
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
skb mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_sorted() will
not queue the skb and return with an error.
None of the callers of this function, issue a kfree_skb() to free the
not queued skb. This results in a memory leak.
This patch fixes the problem by freeing the skb in case of a full queue.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the callers, as this function might
be used in both the rx and tx path.
Fixes: 55059f2b7f86 ("can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions")
Cc: linux-stable <stable@vger.kernel.org>
Cc: Martin Hundebøll <martin@geanix.com>
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
AXI CANIP doesn't support tx fifo empty interrupt feature(TXFEMP),
update the flags filed in the driver for AXI CAN case accordingly.
Fixes: 3281b380ec9f ("can: xilinx_can: Fix flags field initialization for axi can and canps")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d3388 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865be ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver was accessing its driver data after having freed it.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Cc: stable <stable@vger.kernel.org> # 3.9
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver was accessing its driver data after having freed it.
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.
Fixes: 2290aefa2e90 ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk into clk-fixes
Pull Samsung clk driver fixes from Sylwester Nawrocki:
- system suspend related fixes for the exynos542x clocks driver
- probe() error paths fixes in the exynos5433 CMU driver adding
proper release of memory and clk resources
* tag 'clk-v5.4-samsung-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume
clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU
clk: samsung: exynos5433: Fix error paths
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-fixes
Two patches that fix some operator precedence and zeroing of bits
* tag 'sunxi-clk-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
clk: sunxi-ng: a80: fix the zero'ing of bits 16 and 18
clk: sunxi: Fix operator precedence in sunxi_divs_clk_setup
|
|
Commit 3d8598fb9c5a ("clk: ti: clkctrl: use fallback udelay approach if
timekeeping is suspended") added handling for cases when timekeeping is
suspended. But looks like we can still get occasional "failed to enable"
errors on the PM runtime resume path with udelay() returning faster than
expected.
With ti-sysc interconnect target module driver this leads into device
failure with PM runtime failing with "failed to enable" clkctrl error.
Let's fix the issue with a delay of two times the desired delay as in
often done for udelay() to account for the inaccuracy.
Fixes: 3d8598fb9c5a ("clk: ti: clkctrl: use fallback udelay approach if timekeeping is suspended")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lkml.kernel.org/r/20190930154001.46581-1-tony@atomide.com
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
ti_clk_register() calls it already so the driver should not create
duplicated alias.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lkml.kernel.org/r/20191002083436.10194-1-peter.ujfalusi@ti.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull clockevent fixes from Daniel Lezcano:
- Fix scary messages in sh_mtu2 by using platform_irq_count() helper
function (Geert Uytterhoeven)
- Fix double free when using timer-of in the mediatek timer driver
(Fabien Parent)
|
|
This adds support for Intel TH on Jasper Lake PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191028070651.9770-8-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for Intel TH on Comet Lake PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191028070651.9770-7-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'mode' is malloced in mode_store() and should be freed before leaving
from the error handling cases, otherwise it will cause memory leak.
Fixes: 615c164da0eb ("intel_th: msu: Introduce buffer interface")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/lkml/20190801013825.182543-1-weiyongjun1@huawei.com/
Link: https://lore.kernel.org/r/20191028070651.9770-6-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The shift of the unsigned int win->nr_blocks by PAGE_SHIFT may
potentially overflow. Note that the intended return of this shift
is expected to be a size_t however the shift is being performed as
an unsigned int. Fix this by casting win->nr_blocks to a size_t
before performing the shift.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 615c164da0eb ("intel_th: msu: Introduce buffer interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/lkml/20190726113151.8967-1-colin.king@canonical.com/
Link: https://lore.kernel.org/r/20191028070651.9770-5-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 615c164da0eb ("intel_th: msu: Introduce buffer interface") forgot
to add a NULL pointer check for the value returned from kstrdup(), which
will be troublesome if the allocation fails.
Fix that by adding the check.
Addresses-Coverity: ("Dereference null return")
Fixes: 615c164da0eb ("intel_th: msu: Introduce buffer interface")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
[alexander.shishkin: amended the commit message]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/lkml/20190726120421.9650-1-colin.king@canonical.com/
Link: https://lore.kernel.org/r/20191028070651.9770-4-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 615c164da0eb ("intel_th: msu: Introduce buffer interface") added a
mutex that it forgot to initialize, resulting in a lockdep splat.
Fix that by initializing the mutex statically.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 615c164da0eb ("intel_th: msu: Introduce buffer interface")
Link: https://lore.kernel.org/r/20191028070651.9770-3-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 8116db57cf16 ("intel_th: Add switch triggering support") added
a trigger assertion of the CTS, but forgot to de-assert it at the end
of the sequence. This results in window switches randomly not happening.
Fix that by de-asserting the trigger at the end of the window switch
sequence.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: 8116db57cf16 ("intel_th: Add switch triggering support")
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191028070651.9770-2-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some processors may incur a machine check error possibly resulting in an
unrecoverable CPU lockup when an instruction fetch encounters a TLB
multi-hit in the instruction TLB. This can occur when the page size is
changed along with either the physical address or cache type. The relevant
erratum can be found here:
https://bugzilla.kernel.org/show_bug.cgi?id=205195
There are other processors affected for which the erratum does not fully
disclose the impact.
This issue affects both bare-metal x86 page tables and EPT.
It can be mitigated by either eliminating the use of large pages or by
using careful TLB invalidations when changing the page size in the page
tables.
Just like Spectre, Meltdown, L1TF and MDS, a new bit has been allocated in
MSR_IA32_ARCH_CAPABILITIES (PSCHANGE_MC_NO) and will be set on CPUs which
are mitigated against this issue.
Signed-off-by: Vineela Tummalapalli <vineela.tummalapalli@intel.com>
Co-developed-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
|
|
The following build warning occurred on powerpc 64-bit builds:
drivers/cpufreq/powernv-cpufreq.c: In function 'init_chip_info':
drivers/cpufreq/powernv-cpufreq.c:1070:1: warning: the frame size of
1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
This is with a cross-compiler based on gcc 8.1.0, which I got from:
https://mirrors.edge.kernel.org/pub/tools/crosstool/files/bin/x86_64/8.1.0/
The warning is due to putting 1024 bytes on the stack:
unsigned int chip[256];
...and it's also undesirable to have a hard limit on the number of
CPUs here.
Fix both problems by dynamically allocating based on num_possible_cpus,
as recommended by Michael Ellerman.
Fixes: 053819e0bf840 ("cpufreq: powernv: Handle throttling due to Pmax capping at chip level")
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
One of the responsibility of the ->verify() callback is to make sure
that the policy's min frequency is <= max frequency as this isn't
guaranteed by the QoS framework which gave us those values.
Update the comment in cpufreq_set_policy() to clarify that.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Minor changes of the new comment ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
to pick up the KVM fix which is required for the NX series.
|
|
When the compiler decides not to inline the Chunky-to-Planar core
functions, the build fails with:
c2p_planar.c:(.text+0xd6): undefined reference to `c2p_unsupported'
c2p_planar.c:(.text+0x1dc): undefined reference to `c2p_unsupported'
c2p_iplan2.c:(.text+0xc4): undefined reference to `c2p_unsupported'
c2p_iplan2.c:(.text+0x150): undefined reference to `c2p_unsupported'
Fix this by marking the functions __always_inline.
While this could be triggered before by manually enabling both
CONFIG_OPTIMIZE_INLINING and CONFIG_CC_OPTIMIZE_FOR_SIZE, it was exposed
in the m68k defconfig by commit ac7c3e4ff401b304 ("compiler: enable
CONFIG_OPTIMIZE_INLINING forcibly").
Fixes: 9012d011660ea5cf ("compiler: allow all arches to enable CONFIG_OPTIMIZE_INLINING")
Reported-by: noreply@ellerman.id.au
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927094708.11563-1-geert@linux-m68k.org
|
|
This reverts commit 8f86a5b4ad679e4836733b47414226074eee4e4d.
It has been established that this causes a boot regression on
both Baytrail and Cherrytrail SoCs, and we can't have that in
the final kernel release, so we need to revert it.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
