| Age | Commit message (Collapse) | Author |
|---|
|
Thanks to Ville Syrjälä for pointing me towards the cause of this issue.
Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:
[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config] FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config] scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A
Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.
A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.
Changes since v4:
- Fix calculation of final for systems with LVDS panels (fixes BUG() on
CI test suite)
Changes since v3:
- Move temp variable into loop
- Move checks for using_ssc_source to after we've figured out has_ck505
- Add using_ssc_source to debug output
Changes since v2:
- Fix debug output for when we disable the CPU source
Changes since v1:
- Leave the SSC source clock on instead of just shutting it off on all
of the DPLL configurations.
Cc: stable@vger.kernel.org
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465916649-10228-1-git-send-email-cpaul@redhat.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
The comment is wrong, glue is devm_kzalloc-ed mem attached to the
"allwinner,sun4i-a10-musb" compatible platform-dev. Where as
glue->musb_pdev is a newly created "musb-hdrc" platform-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Stop using the return value of platform_device_register_full() to get to
the struct musb in sunxi_musb_work(). If a gadget has been registered
(insmod-ed) before the musb driver, then musb_start will get called
from the musb_core probe function and sunxi_musb_work() may run before
platform_device_register_full() has returned.
Instead store a pointer to struct musb in struct sunxi_glue when
sunxi_musb_enable gets called. Note that sunxi_musb_enable always gets
called before sunxi_musb_work() can run.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[b-liu@ti.com: revise subject prefix]
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 26c5f03 uses a new skb allocator to avoid the RFD overflow
issue.
But from debugging without datasheet, we found the error always
happen when the DMA RX address is set to 0x....fc0, which is very
likely to be a HW/silicon problem.
So one idea is instead of adding a new allocator, why not just
hitting the right target by avaiding the error-prone DMA address?
This patch will actually
* Remove the commit 26c5f03
* Apply rx skb with 64 bytes longer space, and if the allocated skb
has a 0x...fc0 address, it will use skb_resever(skb, 64) to
advance the address, so that the RX overflow can be avoided.
In theory this method should also apply to atl1c driver, which
I can't find anyone who can help to test on real devices.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
Signed-off-by: Feng Tang <feng.tang@intel.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ole Lukoie <olelukoie@mail.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configuring the PHY LED registers for the Marvell 88E1510 and others is
not possible, because regardless of the values in marvell,reg-init, it
is later overridden in m88e1121_config_aneg with a non-standard default.
This patch moves that default configuration to .config_init to allow
setting the LED configuration through marvell,reg-init in the device
tree, which should override said default if it exists.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change power_supply_read_temp() to use power_supply_get_property()
so that it will check the use_cnt and ensure it is > 0. The use_cnt
will be incremented at the end of __power_supply_register, so this
will block to case where get_property can be called before the supply
is fully registered. This fixes the issue show in the stack below:
[ 1.452598] power_supply_read_temp+0x78/0x80
[ 1.458680] thermal_zone_get_temp+0x5c/0x11c
[ 1.464765] thermal_zone_device_update+0x34/0xb4
[ 1.471195] thermal_zone_device_register+0x87c/0x8cc
[ 1.477974] __power_supply_register+0x364/0x424
[ 1.484317] power_supply_register_no_ws+0x10/0x18
[ 1.490833] bq27xxx_battery_setup+0x10c/0x164
[ 1.497003] bq27xxx_battery_i2c_probe+0xd0/0x1b0
[ 1.503435] i2c_device_probe+0x174/0x240
[ 1.509172] driver_probe_device+0x1fc/0x29c
[ 1.515167] __driver_attach+0xa4/0xa8
[ 1.520643] bus_for_each_dev+0x58/0x98
[ 1.526204] driver_attach+0x20/0x28
[ 1.531505] bus_add_driver+0x1c8/0x22c
[ 1.537067] driver_register+0x68/0x108
[ 1.542630] i2c_register_driver+0x38/0x7c
[ 1.548457] bq27xxx_battery_i2c_driver_init+0x18/0x20
[ 1.555321] do_one_initcall+0x38/0x12c
[ 1.560886] kernel_init_freeable+0x148/0x1ec
[ 1.566972] kernel_init+0x10/0xfc
[ 1.572101] ret_from_fork+0x10/0x40
Also make the same change to ps_get_max_charge_cntl_limit() and
ps_get_cur_chrage_cntl_limit() to be safe. Lastly, change the return
value of power_supply_get_property() to -EAGAIN from -ENODEV if
use_cnt <= 0.
Fixes: 297d716f6260 ("power_supply: Change ownership from driver to core")
Cc: stable@vger.kernel.org
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
The incorrect GPIO mask cause kernel warning, when AR9462 access GPIO11.
Also fix the mask for AR9565.
WARNING: CPU: 1 PID: 199 at ../drivers/net/wireless/ath/ath9k/hw.c:2778 ath9k_hw_gpio_get+0x1a9/0x1b0 [ath9k_hw]
CPU: 1 PID: 199 Comm: kworker/u16:9 Not tainted 4.7.0-rc1-next-20160530+ #5
Hardware name: Acer TravelMate P243/BA40_HC, BIOS V1.01 04/20/2012
Workqueue: events_power_efficient rfkill_poll
0000000000000000 ffff88002cf73d28 ffffffff813b8ddc 0000000000000000
0000000000000000 ffff88002cf73d68 ffffffff8107a331 00000ada00000086
ffff880148d9c018 000000000000000b ffff880147e68720 0000000000000200
Call Trace:
[<ffffffff813b8ddc>] dump_stack+0x63/0x87
[<ffffffff8107a331>] __warn+0xd1/0xf0
[<ffffffff8107a41d>] warn_slowpath_null+0x1d/0x20
[<ffffffffc0775b19>] ath9k_hw_gpio_get+0x1a9/0x1b0 [ath9k_hw]
[<ffffffffc047f3e4>] ath9k_rfkill_poll_state+0x34/0x60 [ath9k]
[<ffffffffc06dbb53>] ieee80211_rfkill_poll+0x33/0x40 [mac80211]
[<ffffffffc03ad65a>] cfg80211_rfkill_poll+0x2a/0xc0 [cfg80211]
[<ffffffff817c5514>] rfkill_poll+0x24/0x50
[<ffffffff81093183>] process_one_work+0x153/0x3f0
[<ffffffff8109393b>] worker_thread+0x12b/0x4b0
[<ffffffff81093810>] ? rescuer_thread+0x340/0x340
[<ffffffff81099129>] kthread+0xc9/0xe0
[<ffffffff817d8f1f>] ret_from_fork+0x1f/0x40
[<ffffffff81099060>] ? kthread_park+0x60/0x60
Fixes: a01ab81b09c5 ("ath9k: define correct GPIO numbers and bits mask")
Reported-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
commit 5c86d97bcc1d ("ath10k: combine txrx and replenish task")
introduced deadlock while processing rx in order indication message
for qca6174 based devices. While merging replenish and txrx tasklets,
replenish task should be called out of htt rx ring locking since it
is also try to acquire the same lock.
Unfortunately this issue is not exposed by other solutions (qca988x,
qca99x0 & qca4019), as rx_in_ord_ind message is specific to qca6174
based devices. This patch fixes
=============================================
[ INFO: possible recursive locking detected ]
4.7.0-rc2-wt-ath+ #1353 Tainted: G E
---------------------------------------------
swapper/3/0 is trying to acquire lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d7ef19>]
ath10k_htt_rx_msdu_buff_replenish+0x29/0x90 [ath10k_core]
but task is already holding lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&htt->rx_ring.lock)->rlock);
lock(&(&htt->rx_ring.lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by swapper/3/0:
#0: (&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=119151
Fixes: 5c86d97bcc1d ("ath10k: combine txrx and replenish task")
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When allocating a new device IRQ, gic_dev_domain_alloc() correctly calls
irq_domain_set_hwirq_and_chip(), but gic_irq_domain_alloc() does not. This
means that gic_irq_domain believes all IRQs from the dev domain have an
hwirq of 0 and creates incorrect mappings in the linear_revmap. As
gic_irq_domain is a parent of the gic_dev_domain, this leads to an
inability to boot on devices with a GIC. Excerpt of the error:
[ 2.297649] irq 0: nobody cared (try booting with the "irqpoll" option)
...
[ 2.436963] handlers:
[ 2.439492] Disabling IRQ #0
Fix this by calling irq_domain_set_hwirq_and_chip() for both the dev and
irq domain.
Now that we are modifying the parent domain, be sure to clear it up in
case of an allocation error.
Fixes: c98c1822ee13 ("irqchip/mips-gic: Add device hierarchy domain")
Fixes: 2af70a962070 ("irqchip/mips-gic: Add a IPI hierarchy domain")
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Tested-by: Govindraj Raja <Govindraj.Raja@imgtec.com> # On Pistachio SoC
Reviewed-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: jason@lakedaemon.net
Cc: marc.zyngier@arm.com
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1464001552-31174-1-git-send-email-harvey.hunt@imgtec.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The trasfer timeout is fixed at 1000 ms. Reading a 4Mbyte flash over
1MHz SPI bus takes way longer than that. Calculate the timeout from the
actual time the transfer is supposed to take and multiply by 2 for good
measure.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
When testing SPI without DMA I noticed that filling the FIFO on the
spi controller causes timeout.
Always leave room for one byte in the FIFO.
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The PWM device exposed by the HLCDC IP is configured with an inverted
polarity by default. Registering the PWM chip with the normal polarity
was not a problem before commit 42e8992c58d4 ("pwm: Add core
infrastructure to allow atomic updates") because the ->set_polarity()
hook was called no matter the current polarity state, but this is no longer
the case.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Directly accessing inode fields bypasses ->getattr()
and can cause problems when the underlying filesystem
does not have the default ->getattr() implementation.
So instead of obtaining the backing inode via d_backing_inode()
use vfs_getattr() and obtain what we need from the kstat struct.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This reverts commit 87f15d4add758fb7fc76655721af94be57a4c17d.
vfs_stat() can only be used on user supplied buffers.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This reverts commit 322ea0bbf3003df17b6253f76e572c37d79a6810.
vfs_stat() can only be used on user supplied buffers.
UBI's kapi.c is the API to the kernel and therefore vfs_stat()
is inappropriate.
This solves the problem that mounting any UBIFS will immediately
fail with -EINVAL.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Fix warning about tainted kernel because usb-otg-fsm has no license.
WARNING: with this patch usb-otg-fsm module can be loaded
but then the kernel will hang. Tested with a udoo quad board.
Cc: <stable@vger.kernel.org> #v4.1+
Signed-off-by: Oscar <oscar@naiandei.net>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Acquire a reference to the carrier's kernel module in bus code, so
it can't be removed from the kernel while it still has a bus and thus
possibly devices attached to it.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Andreas Werner <andreas.werner@men.de>
Tested-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mcb_probe() does not aqcuire a reference to the probed device but drops one
when removing the device. As it is actually using the device, it should grab
a reference via get_device().
This could lead to a panic found with a rmmod/modprobe stress test
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reported-by: Andreas Werner <andreas.werner@men.de>
Tested-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 2ba272d7bde27e1db2cf1c6cee49b01b7ea08989.
The issue fixed by this patch is specific to compute rings and the
previous patch was enough. Additionally, this patch as been traced
to strange behavior on some CZ systems so we might as well drop it.
|
|
Wrong operator.
Reported-by: David Binderman <linuxdev.baldrick@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When executing in a PCI passthrough based virtuzliation environment, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.
Ported from amdgpu commit:
amdgpu: fix asic initialization for virtualized environments
Cc: Andres Rodriguez <andres.rodriguez@amd.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
When executing in a PCI passthrough based virtuzliation environemnt, the
hypervisor will usually attempt to send a PCIe bus reset signal to the
ASIC when the VM reboots. In this scenario, the card is not correctly
initialized, but we still consider it to be posted. Therefore, in a
passthrough based environemnt we should always post the card to guarantee
it is in a good state for driver initialization.
However, if we are operating in SR-IOV mode it is up to the GIM driver
to manage the asic state, therefore we should not post the card (and
shouldn't be able to do it either).
v2: add missing semi-colon
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Andres Rodriguez <andres.rodriguez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Seems to cause problems for some older hardware. Kudos to Thom Kouwenhoven
for working a lot with the PLLs and figuring this out.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Seems r600/r700 does not like hard reset while freezing for hibernation
(regression due to 274ad65c9d02bdcbee9bae045517864c3521d530 which itself
is a fix for hibernation on some GPU families). Until i can debug further
issue with r600, let just disable this for r600/r700 as they are very
similar family and bug affecting one likely affect the other.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
'regulator/fix/tps51632' into regulator-linus
|
|
Commit 7ea0ed2b5be8 ("ipmi: Make the message handler easier to use for
SMI interfaces") changed handle_new_recv_msgs() to call handle_one_recv_msg()
for a smi_msg while the smi_msg is still connected to waiting_rcv_msgs list.
That could lead to following list corruption problems:
1) low-level function treats smi_msg as not connected to list
handle_one_recv_msg() could end up calling smi_send(), which
assumes the msg is not connected to list.
For example, the following sequence could corrupt list by
doing list_add_tail() for the entry still connected to other list.
handle_new_recv_msgs()
msg = list_entry(waiting_rcv_msgs)
handle_one_recv_msg(msg)
handle_ipmb_get_msg_cmd(msg)
smi_send(msg)
spin_lock(xmit_msgs_lock)
list_add_tail(msg)
spin_unlock(xmit_msgs_lock)
2) race between multiple handle_new_recv_msgs() instances
handle_new_recv_msgs() once releases waiting_rcv_msgs_lock before calling
handle_one_recv_msg() then retakes the lock and list_del() it.
If others call handle_new_recv_msgs() during the window shown below
list_del() will be done twice for the same smi_msg.
handle_new_recv_msgs()
spin_lock(waiting_rcv_msgs_lock)
msg = list_entry(waiting_rcv_msgs)
spin_unlock(waiting_rcv_msgs_lock)
|
| handle_one_recv_msg(msg)
|
spin_lock(waiting_rcv_msgs_lock)
list_del(msg)
spin_unlock(waiting_rcv_msgs_lock)
Fixes: 7ea0ed2b5be8 ("ipmi: Make the message handler easier to use for SMI interfaces")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
[Added a comment to describe why this works.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: stable@vger.kernel.org # 3.19
Tested-by: Ye Feng <yefeng.yl@alibaba-inc.com>
|
|
Fixes: 9ae482104cb9 ("gpio: 104-idi-48: Clear pending interrupt once in IRQ handler")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The hash buffer is really HASH_BLOCK_SIZE bytes, someone
must have thought that memmove takes n*u32 words by mistake.
Tests work as good/bad as before after this patch.
Cc: Joakim Bech <joakim.bech@linaro.org>
Cc: stable@vger.kernel.org
Reported-by: David Binderman <linuxdev.baldrick@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
All of the VMX AES ciphers (AES, AES-CBC and AES-CTR) are set at
priority 1000. Unfortunately this means we never use AES-CBC and
AES-CTR, because the base AES-CBC cipher that is implemented on
top of AES inherits its priority.
To fix this, AES-CBC and AES-CTR have to be a higher priority. Set
them to 2000.
Testing on a POWER8 with:
cryptsetup benchmark --cipher aes --key-size 256
Shows decryption speed increase from 402.4 MB/s to 3069.2 MB/s,
over 7x faster. Thanks to Mike Strosaker for helping me debug
this issue.
Fixes: 8c755ace357c ("crypto: vmx - Adding CBC routines for VMX module")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When calling ppc-xlate.pl, we pass it either linux-ppc64 or
linux-ppc64le. The script however was expecting linux64le, a result
of its OpenSSL origins. This means we aren't obeying the ppc64le
ABIv2 rules.
Fix this by checking for linux-ppc64le.
Fixes: 5ca55738201c ("crypto: vmx - comply with ABIs that specify vrsave as reserved.")
Cc: stable@vger.kernel.org
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The map_sg callback is missing from arm_smmu_ops, but is required by
iommu.h. Similarly to most other IOMMU drivers, connect it to
default_iommu_map_sg.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This patch adds support to list_voltage callback, so that consumers
like mmc core, can get information of supported voltage range.
Without this patch there is no way for mmc core to know this voltage range.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There is no reason to destroy channels that are destroyed while
cpdma_ctlr destroy. In this case no need to remember how much
channels where created and destroy them by one, as cpdma_ctlr
destroys all of them.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- fix an ordering issue in cpu cooling that cooling device is
registered before it's ready (freq_table being populated).
(Lukasz Luba)
- fix a missing comment update (Caesar Wang)
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: add the note for set_trip_temp
thermal: cpu_cooling: fix improper order during initialization
|
|
Pull block layer fixes from Jens Axboe:
"A small collection of fixes for the current series. This contains:
- Two fixes for xen-blkfront, from Bob Liu.
- A bug fix for NVMe, releasing only the specific resources we
requested.
- Fix for a debugfs flags entry for nbd, from Josef.
- Plug fix from Omar, fixing up a case of code being switched between
two functions.
- A missing bio_put() for the new discard callers of
submit_bio_wait(), fixing a regression causing a leak of the bio.
From Shaun.
- Improve dirty limit calculation precision in the writeback code,
fixing a case where setting a limit lower than 1% of memory would
end up being zero. From Tejun"
* 'for-linus' of git://git.kernel.dk/linux-block:
NVMe: Only release requested regions
xen-blkfront: fix resume issues after a migration
xen-blkfront: don't call talk_to_blkback when already connected to blkback
nbd: pass the nbd pointer for flags debugfs
block: missing bio_put following submit_bio_wait
blk-mq: really fix plug list flushing for nomerge queues
writeback: use higher precision calculation in domain_dirty_limits()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A new bunch of GPIO fixes for v4.7.
This time I am very grateful that Ricardo Ribalda Delgado went in and
fixed my stupid refcounting mistakes in the removal path for GPIO
chips. I had a feeling something was wrong here and so it was. It
exploded on OMAP and it fixes their problem. Now it should be (more)
solid.
The rest i compilation, Kconfig and driver fixes. Some tagged for
stable.
Summary:
- Fix a NULL pointer dereference when we are searching the GPIO
device list but one of the devices have been removed (struct
gpio_chip pointer is NULL).
- Fix unaligned reference counters: we were ending on +3 after all
said and done. It should be 0. Remove an extraneous get_device(),
and call cdev_del() followed by device_del() in gpiochip_remove()
instead and the count goes to zero and calls the release() function
properly.
- Fix a compile warning due to a missing #include in the OF/device
tree portions.
- Select ANON_INODES for GPIOLIB, we're using that for our character
device. Some randconfig tests disclosed the problem.
- Make sure the Zynq driver clock runs also without CONFIG_PM enabled
- Fix an off-by-one error in the 104-DIO-48E driver
- Fix warnings in bcm_kona_gpio_reset()"
* tag 'gpio-v4.7-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: bcm-kona: fix bcm_kona_gpio_reset() warnings
gpio: select ANON_INODES
gpio: include <linux/io-mapping.h> in gpiolib-of
gpiolib: Fix unaligned used of reference counters
gpiolib: Fix NULL pointer deference
gpio: zynq: initialize clock even without CONFIG_PM
gpio: 104-dio-48e: Fix control port offset computation off-by-one error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two current fixes:
- one affects Qemu CD ROM emulation, which stopped working after the
updates in SCSI to require VPD pages from all conformant devices.
Fix temporarily by blacklisting Qemu (we can relax later when they
come into compliance).
- The other is a fix to the optimal transfer size. We set up a
minefield for ourselves by being confused about whether the limits
are in bytes or sectors (SCSI optimal is in blocks and the queue
parameter is in bytes).
This tries to fix the problem (wrong setting for queue limits
max_sectors) and make the problem more obvious by introducing a
wrapper function"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
sd: Fix rw_max for devices that report an optimal xfer size
scsi: Add QEMU CD-ROM to VPD Inquiry Blacklist
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
- a bigger fix for i801 to finally be able to be loaded on some
machines again
- smaller driver fixes
- documentation update because of a renamed file
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: mux: reg: Provide of_match_table
i2c: mux: refer to i2c-mux.txt
i2c: octeon: Avoid printk after too long SMBUS message
i2c: octeon: Missing AAK flag in case of I2C_M_RECV_LEN
i2c: i801: Allow ACPI SystemIO OpRegion to conflict with PCI BAR
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- fix unflatten_dt_nodes when dad parameter is set.
- add vendor prefixes for TechNexion and UniWest
- documentation fix for Marvell BT
- OF IRQ kerneldoc fixes
- restrict CMA alignment adjustments to non dma-coherent
- a couple of warning fixes in reserved-memory code
- DT maintainers updates
* tag 'devicetree-fixes-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
drivers: of: add definition of early_init_dt_alloc_reserved_memory_arch
drivers/of: Fix depth for sub-tree blob in unflatten_dt_nodes()
drivers: of: Fix of_pci.h header guard
dt-bindings: Add vendor prefix for TechNexion
of: add vendor prefix for UniWest
dt: bindings: fix documentation for MARVELL's bt-sd8xxx wireless device
of: add missing const for of_parse_phandle_with_args() in !CONFIG_OF
of: silence warnings due to max() usage
drivers: of: of_reserved_mem: fixup the CMA alignment not to affect dma-coherent
of: irq: fix of_irq_get[_byname]() kernel-doc
MAINTAINERS: DeviceTree maintainer updates
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux
Pull uvc compat XU ioctl fixes from Andy Lutomirski:
"uvc's compat XU ioctls go through tons of potentially buggy
indirection. The first patch removes the indirection. The second one
cleans up the code.
Compile-tested only. I have the hardware, but I have absolutely no
idea what XU does, how to use it, what software to recompile as
32-bit, or what to test in that software"
* tag '20160610_uvc_compat_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/luto/linux:
uvc_v4l2: Simplify compat ioctl implementation
uvc: Forward compat ioctls to their handlers directly
|
|
Correctly handle the settling time cycles value. The else branch is an
impossible condition, > 1022 in the else branch of > 511. Flipping the order.
Based on the Table 13 at the bottom of Page 25 of the Data Sheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/AD5933.pdf
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
As pointed out by Geert Uytterhoeven, the patch was incorrect
and breaks the driver, which was fortunately pointed out by
this gcc warning:
drivers/staging/iio/adc/ad7606_spi.c: In function ‘ad7606_spi_read_block’:
drivers/staging/iio/adc/ad7606_spi.c:34: warning: ‘data’ is used uninitialized in this function
The effect of the patch is that the data is copied into
a random memory location (from the uninitialized pointer)
instead of being byteswapped in place.
This adds the initialization for the 'data' variable back
to restore the original behavior.
Cc: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Fixes: 87787e5ef727 ("Staging: iio: Fix sparse endian warning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
In some cases this can result in incorrectly returning a negative value
from asus_acpi_get_sensor_info and the AK8963 magnetometer failing to
show up.
Note cpm is an alias for buffer.pointer which isn't apparent in this
patch on it's own.
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Commit 7f854420fbfe9d49afe2ffb1df052cfe8e215541
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a2f27217e4e60e663b5b971b0ccb287a9548b04e.
I applied the wrong version of this.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 7f854420fbfe9d49afe2ffb1df052cfe8e215541
("phy: Add API for {un}registering an mdio device to a bus.")
broke PHY detection on this driver with a copy-paste bug:
The code is looking 32 times for a PHY at address 0.
Fixes ethernet on AMD DB1100/DB1500/DB1550 boards which have
their (autodetected) PHYs at address 31.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code checks if the queue should be stopped because we are below the
threshold of free descriptors only to check if it should be started again.
If we do end up in a state where we are at the threshold limit, it makes
more sense to just stop the queue and wait for the next IRQ to trigger the
TX housekeeping again. There is no rush in enqueuing the next packet, it
needs to wait for all the others in the queue to be dispatched first
anyway.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code unconditionally wakes up the queue at the end of each
tx_poll action. Change the code to only wake up the queues if any of
them have actually been stopped before.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TX ring setup has an off by one error causing it to not utilise all
descriptors. This has the side effect that we need to reset the next
pointer at runtime to make it work. Fix the off by one and remove the
code fixing the ring at runtime.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During stress testing, after reducing the threshold value, we have seen
TX timeouts that were caused by the watchdog_timeo value being too low.
Increase the value to 5 * HZ which is a value commonly used by many other
drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
