summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-08-18net: mscc: ocelot: remove duplicate "the the" phrase in Kconfig textColin Ian King
The Kconfig help text contains the phrase "the the" in the help text. Fix this. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18bonding: fix active-backup failover for current ARP slaveJiri Wiesner
When the ARP monitor is used for link detection, ARP replies are validated for all slaves (arp_validate=3) and fail_over_mac is set to active, two slaves of an active-backup bond may get stuck in a state where both of them are active and pass packets that they receive to the bond. This state makes IPv6 duplicate address detection fail. The state is reached thus: 1. The current active slave goes down because the ARP target is not reachable. 2. The current ARP slave is chosen and made active. 3. A new slave is enslaved. This new slave becomes the current active slave and can reach the ARP target. As a result, the current ARP slave stays active after the enslave action has finished and the log is littered with "PROBE BAD" messages: > bond0: PROBE: c_arp ens10 && cas ens11 BAD The workaround is to remove the slave with "going back" status from the bond and re-enslave it. This issue was encountered when DPDK PMD interfaces were being enslaved to an active-backup bond. I would be possible to fix the issue in bond_enslave() or bond_change_active_slave() but the ARP monitor was fixed instead to keep most of the actions changing the current ARP slave in the ARP monitor code. The current ARP slave is set as inactive and backup during the commit phase. A new state, BOND_LINK_FAIL, has been introduced for slaves in the context of the ARP monitor. This allows administrators to see how slaves are rotated for sending ARP requests and attempts are made to find a new active slave. Fixes: b2220cad583c9 ("bonding: refactor ARP active-backup monitor") Signed-off-by: Jiri Wiesner <jwiesner@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18drm/amd/display: use correct scale for actual_brightnessAlexander Monakov
Documentation for sysfs backlight level interface requires that values in both 'brightness' and 'actual_brightness' files are interpreted to be in range from 0 to the value given in the 'max_brightness' file. With amdgpu, max_brightness gives 255, and values written by the user into 'brightness' are internally rescaled to a wider range. However, reading from 'actual_brightness' gives the raw register value without inverse rescaling. This causes issues for various userspace tools such as PowerTop and systemd that expect the value to be in the correct range. Introduce a helper to retrieve internal backlight range. Use it to reimplement 'convert_brightness' as 'convert_brightness_from_user' and introduce 'convert_brightness_to_user'. Bug: https://bugzilla.kernel.org/show_bug.cgi?id=203905 Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1242 Cc: Alex Deucher <alexander.deucher@amd.com> Cc: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alexander Monakov <amonakov@ispras.ru> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: should check error using DC_OKTong Zhang
core_link_read_dpcd returns only DC_OK(1) and DC_ERROR_UNEXPECTED(-1), the caller should check error using DC_OK instead of checking against 0 Signed-off-by: Tong Zhang <ztong0001@gmail.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: fix potential integer overflow when shifting 32 bit ↵Colin Ian King
variable bl_pwm The 32 bit unsigned integer bl_pwm is being shifted using 32 bit arithmetic and then being assigned to a 64 bit unsigned integer. There is a potential for a 32 bit overflow so cast bl_pwm to enforce a 64 bit shift operation to avoid this. Addresses-Coverity: ("unintentional integer overflow") Fixes: 3ba01817365c ("drm/amd/display: Move panel_cntl specific register from abm to panel_cntl.") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu/pm: only hide average power on SI and pre-RENOIR APUsAlex Deucher
We can get this on RENOIR and newer via the SMU metrics table. Reviewed-by: Evan Quan <evan.quan@amd.com> Acked-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu/swsmu: implement power metrics for RENOIRAlex Deucher
Grab the data from the SMU metrics table. Reviewed-by: Evan Quan <evan.quan@amd.com> Acked-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu/swsmu: implement voltage metrics for RENOIRAlex Deucher
Grab the data from the SMU metrics table. Reviewed-by: Evan Quan <evan.quan@amd.com> Acked-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu/pm: remove duplicate checkAlex Deucher
FAMILY_KV is APUs and we already check for APUs. Reviewed-by: Evan Quan <evan.quan@amd.com> Acked-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu/jpeg: remove redundant check when it returnsLeo Liu
Fix warning from kernel test robot v2: remove the local variable as well Signed-off-by: Leo Liu <leo.liu@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Acked-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu: Limit the error info print ratejqdeng
Use function printk_ratelimit to limit the print rate. Signed-off-by: jqdeng <Emily.Deng@amd.com> Acked-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu: Fix repeatly flr issuejqdeng
Only for no job running test case need to do recover in flr notification. For having job in mirror list, then let guest driver to hit job timeout, and then do recover. Signed-off-by: jqdeng <Emily.Deng@amd.com> Acked-by: Nirmoy Das <nirmoy.das@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/pm: add SMU11 common deep sleep control interfaceEvan Quan
Considering the same logic can be applied to Arcturus, Navi1X and Sienna Cichlid. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/pm: disable/enable deep sleep features on UMD pstate enter/exitEvan Quan
Add deep sleep disablement/enablement on UMD pstate entering/exiting. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/pm: add SMU11 common gfx ulv control interfaceEvan Quan
Considering the same logic can be applied to Arcturus, Navi1X and Sienna Cichlid. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/pm: disable/enable gfx ulv on UMD pstate enter/exitEvan Quan
Add gfx ulv disablement/enablement on UMD pstate entering/exiting. Signed-off-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/pm: update driver if version for navy_flounderJiansong Chen
It's in accordance with pmfw 65.7.0 for navy_flounder. Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18Revert "drm/amdgpu: disable gfxoff for navy_flounder"Jiansong Chen
This reverts commit ba4e049e63b607ac2e0c070b1406826390d5047e. Newly released sdma fw (51.52) provides a fix for the issue. Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/scheduler: Remove priority macro INVALID (v2)Luben Tuikov
Remove DRM_SCHED_PRIORITY_INVALID. We no longer carry around an invalid priority and cut it off at the source. Backwards compatibility behaviour of AMDGPU CTX IOCTL passing in garbage for context priority from user space and then mapping that to DRM_SCHED_PRIORITY_NORMAL is preserved. v2: Revert "res" --> "r" and "prio" --> "priority". Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/scheduler: Scheduler priority fixes (v2)Luben Tuikov
Remove DRM_SCHED_PRIORITY_LOW, as it was used in only one place. Rename and separate by a line DRM_SCHED_PRIORITY_MAX to DRM_SCHED_PRIORITY_COUNT as it represents a (total) count of said priorities and it is used as such in loops throughout the code. (0-based indexing is the the count number.) Remove redundant word HIGH in priority names, and rename *KERNEL* to *HIGH*, as it really means that, high. v2: Add back KERNEL and remove SW and HW, in lieu of a single HIGH between NORMAL and KERNEL. Signed-off-by: Luben Tuikov <luben.tuikov@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: Add dsc_to_stream_resource for dcn3Bhawanpreet Lakha
Without this, enabling dsc will cause a nullptr Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com> Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdkfd: Initialize SDMA activity counter to 0Mukul Joshi
To prevent reporting erroneous SDMA usage, initialize SDMA activity counter to 0 before using. Signed-off-by: Mukul Joshi <mukul.joshi@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: fix pow() crashing when given base 0Krunoslav Kovac
[Why&How] pow(a,x) is implemented as exp(x*log(a)). log(0) will crash. So return 0^x = 0, unless x=0, convention seems to be 0^0 = 1. Cc: stable@vger.kernel.org Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: Reset scrambling on Test PatternChris Park
[Why] Programming is missing the sequence where for eDP the scrambling is reset when testing for eye diagram test pattern. [How] Include the required register in the definition Signed-off-by: Chris Park <Chris.Park@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: fix dcn3 wide timing dsc validationDmytro Laktyushkin
Wide timing DSC requires odm. Since spreadsheet is missing this dsc validation we have to modify DML vba code ourselves. Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: Fix DFPstate hang due to view port changedPaul Hsieh
[Why] Place the cursor in the center of screen between two pipes then adjusting the viewport but cursour doesn't update cause DFPstate hang. [How] If viewport changed, update cursor as well. Cc: stable@vger.kernel.org Signed-off-by: Paul Hsieh <paul.hsieh@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: Assign correct left shiftChris Park
[Why] Reading for DP alt registers return incorrect values due to LE_SF definition missing. [How] Define correct LE_SF or DP alt registers. Signed-off-by: Chris Park <Chris.Park@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amd/display: Call DMUB for eDP power controlChris Park
[Why] If DMUB is used, LVTMA VBIOS call can be used to control eDP instead of tranditional transmitter control. Interface is agreed with VBIOS for eDP to use this new path to program LVTMA registers. [How] Create DAL interface to send DMUB command for LVTMA as currently implemented in VBIOS. Signed-off-by: Chris Park <Chris.Park@amd.com> Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdkfd: fix the wrong sdma instance query for renoirHuang Rui
Renoir only has one sdma instance, it will get failed once query the sdma1 registers. So use switch-case instead of static register array. Signed-off-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu: parse ta firmware for navy_flounderBhawanpreet Lakha
Use the same case as sienna_cichlid Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18Merge tag 'spi-fix-v5.9-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi Pull spi fixes from Mark Brown: "A bunch of fixes that came in for SPI during the merge window. Some from ST and others for their controller, one from Lukas for a race between device addition and controller unregistration and one from fix from Geert for the DT bindings which unbreaks validation" * tag 'spi-fix-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: dt-bindings: lpspi: Add missing boolean type for fsl,spi-only-use-cs1-sel spi: stm32: always perform registers configuration prior to transfer spi: stm32: fixes suspend/resume management spi: stm32: fix stm32_spi_prepare_mbr in case of odd clk_rate spi: stm32: fix fifo threshold level in case of short transfer spi: stm32h7: fix race condition at end of transfer spi: stm32: clear only asserted irq flags on interrupt spi: Prevent adding devices below an unregistering controller
2020-08-18drm/amdgpu: fix NULL pointer access issue when unloading driverGuchun Chen
When unloading driver by "modprobe -r amdgpu", one NULL pointer dereference bug occurs in ras debugfs releasing. The cause is the duplicated debugfs_remove, as drm debugfs_root dir has been cleaned up already by drm_minor_unregister. BUG: kernel NULL pointer dereference, address: 00000000000000a0 PGD 0 P4D 0 Oops: 0002 [#1] SMP PTI CPU: 11 PID: 1526 Comm: modprobe Tainted: G OE 5.6.0-guchchen #1 Hardware name: System manufacturer System Product Name/TUF Z370-PLUS GAMING II, BIOS 0411 09/21/2018 RIP: 0010:down_write+0x15/0x40 Code: eb de e8 7e 17 72 ff cc cc cc cc cc cc cc cc cc cc cc cc cc cc 0f 1f 44 00 00 53 48 89 fb e8 92 d8 ff ff 31 c0 ba 01 00 00 00 <f0> 48 0f b1 13 75 0f 65 48 8b 04 25 c0 8b 01 00 48 89 43 08 5b c3 RSP: 0018:ffffb1590386fcd0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 00000000000000a0 RCX: 0000000000000000 RDX: 0000000000000001 RSI: ffffffff85b2fcc2 RDI: 00000000000000a0 RBP: ffffb1590386fd30 R08: ffffffff85b2fcc2 R09: 000000000002b3c0 R10: ffff97a330618c40 R11: 00000000000005f6 R12: ffff97a3481beb40 R13: 00000000000000a0 R14: ffff97a3481beb40 R15: 0000000000000000 FS: 00007fb11a717540(0000) GS:ffff97a376cc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000000a0 CR3: 00000004066d6006 CR4: 00000000003606e0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: simple_recursive_removal+0x63/0x370 ? debugfs_remove+0x60/0x60 debugfs_remove+0x40/0x60 amdgpu_ras_fini+0x82/0x230 [amdgpu] ? __kernfs_remove.part.17+0x101/0x1f0 ? kernfs_name_hash+0x12/0x80 amdgpu_device_fini+0x1c0/0x580 [amdgpu] amdgpu_driver_unload_kms+0x3e/0x70 [amdgpu] amdgpu_pci_remove+0x36/0x60 [amdgpu] pci_device_remove+0x3b/0xb0 device_release_driver_internal+0xe5/0x1c0 driver_detach+0x46/0x90 bus_remove_driver+0x58/0xd0 pci_unregister_driver+0x29/0x90 amdgpu_exit+0x11/0x25 [amdgpu] __x64_sys_delete_module+0x13d/0x210 do_syscall_64+0x5f/0x250 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by: Guchun Chen <guchun.chen@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu: fix uninit-value in arcturus_log_thermal_throttling_event()Kevin Wang
when function arcturus_get_smu_metrics_data() call failed, it will cause the variable "throttler_status" isn't initialized before use. warning: powerplay/arcturus_ppt.c:2268:24: warning: ‘throttler_status’ may be used uninitialized in this function [-Wmaybe-uninitialized] 2268 | if (throttler_status & logging_label[throttler_idx].feature_mask) { Signed-off-by: Kevin Wang <kevin1.wang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/amdgpu: disable gfxoff for navy_flounderJiansong Chen
gfxoff is temporarily disabled for navy_flounder, since at present the feature has broken some basic amdgpu test. Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com> Reviewed-by: Tao Zhou <tao.zhou1@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-08-18drm/panel: Use dev_ based loggingSam Ravnborg
Standardize on the dev_ based logging and drop the include of drm_print.h. Fix a few cases where "x@" was used when printing the mode. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Guido Günther <agx@sigxcpu.org> Cc: Jerry Han <hanxu5@huaqin.corp-partner.google.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Icenowy Zheng <icenowy@aosc.io> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Guido Günther <agx@sigxcpu.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200815125406.1153224-6-sam@ravnborg.org
2020-08-18drm/panel: sitronix: Use dev_ based loggingSam Ravnborg
Standardize on the dev_ based logging and drop the include of drm_print.h. Fix a few cases where "x@" was used when printing the mode. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Guido Günther <agx@sigxcpu.org> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Guido Günther <agx@sigxcpu.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200815125406.1153224-5-sam@ravnborg.org
2020-08-18drm/panel: raydium: Use dev_ based loggingSam Ravnborg
Standardize on the dev_ based logging and drop the include of drm_print.h. Fix a few cases where "x@" was used when printing the mode. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Guido Günther <agx@sigxcpu.org> Cc: Robert Chiras <robert.chiras@nxp.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Guido Günther <agx@sigxcpu.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200815125406.1153224-4-sam@ravnborg.org
2020-08-18drm/panel: leadtek: Use dev_ based loggingSam Ravnborg
Standardize on the dev_ based logging and drop the include of drm_print.h. Fix a few cases where "x@" was used when printing the mode. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Guido Günther <agx@sigxcpu.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Guido Günther <agx@sigxcpu.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200815125406.1153224-3-sam@ravnborg.org
2020-08-18drm/panel: samsung: Use dev_ based loggingSam Ravnborg
Standardize on the dev_ based logging and drop the include of drm_print.h. Fix a few cases where "x@" was used when printing the mode. Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Guido Günther <agx@sigxcpu.org> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Guido Günther <agx@sigxcpu.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200815125406.1153224-2-sam@ravnborg.org
2020-08-18net: gianfar: Add of_node_put() before goto statementSumera Priyadarsini
Every iteration of for_each_available_child_of_node() decrements reference count of the previous node, however when control is transferred from the middle of the loop, as in the case of a return or break or goto, there is no decrement thus ultimately resulting in a memory leak. Fix a potential memory leak in gianfar.c by inserting of_node_put() before the goto statement. Issue found with Coccinelle. Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18cxgb4: Fix race between loopback and normal Tx pathGanji Aravind
Even after Tx queues are marked stopped, there exists a small window where the current packet in the normal Tx path is still being sent out and loopback selftest ends up corrupting the same Tx ring. So, ensure selftest takes the Tx lock to synchronize access the Tx ring. Fixes: 7235ffae3d2c ("cxgb4: add loopback ethtool self-test") Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18cxgb4: Fix work request size calculation for loopback testGanji Aravind
Work request used for sending loopback packet needs to add the firmware work request only once. So, fix by using correct structure size. Fixes: 7235ffae3d2c ("cxgb4: add loopback ethtool self-test") Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18sfc: don't free_irq()s if they were never requestedEdward Cree
If efx_nic_init_interrupt fails, or was never run (e.g. due to an earlier failure in ef100_net_open), freeing irqs in efx_nic_fini_interrupt is not needed and will cause error messages and stack traces. So instead, only do this if efx_nic_init_interrupt successfully completed, as indicated by the new efx->irqs_hooked flag. Fixes: 965b549f3c20 ("sfc_ef100: implement ndo_open/close and EVQ probing") Signed-off-by: Edward Cree <ecree@solarflare.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18sfc: null out channel->rps_flow_id after freeing itEdward Cree
If an ef100_net_open() fails, ef100_net_stop() may be called without channel->rps_flow_id having been written; thus it may hold the address freed by a previous ef100_net_stop()'s call to efx_remove_filters(). This then causes a double-free when efx_remove_filters() is called again, leading to a panic. To prevent this, after freeing it, overwrite it with NULL. Fixes: a9dc3d5612ce ("sfc_ef100: RX filter table management and related gubbins") Signed-off-by: Edward Cree <ecree@solarflare.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18sfc: take correct lock in ef100_reset()Edward Cree
When downing and upping the ef100 filter table, we need to take a write lock on efx->filter_sem, not just a read lock, because we may kfree() the table pointers. Without this, resets cause a WARN_ON from efx_rwsem_assert_write_locked(). Fixes: a9dc3d5612ce ("sfc_ef100: RX filter table management and related gubbins") Signed-off-by: Edward Cree <ecree@solarflare.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18sfc: really check hash is valid before using itEdward Cree
Actually hook up the .rx_buf_hash_valid method in EF100's nic_type. Fixes: 068885434ccb ("sfc: check hash is valid before using it") Reported-by: Martin Habets <mhabets@solarflare.com> Signed-off-by: Edward Cree <ecree@solarflare.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18macvlan: validate setting of multiple remote source MAC addressesAlvin Šipraga
Remote source MAC addresses can be set on a 'source mode' macvlan interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit tightens the validation of these MAC addresses to match the validation already performed when setting or adding a single MAC address via the IFLA_MACVLAN_MACADDR attribute. iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set' command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command, which demonstrates the inconsistent behaviour that this commit addresses: # ip link add link eth0 name macvlan0 type macvlan mode source # ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00 RTNETLINK answers: Cannot assign requested address # ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00 # ip -d link show macvlan0 5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ... link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0 macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ... With this change, the 'set' command will (rightly) fail in the same way as the 'add' command. Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-18Revert "HID: usbhid: do not sleep when opening device"Jiri Kosina
This reverts commit d3132792285859253c466354fd8d54d1fe0ba786. This patch causes a regression with quite a few devices, as probing fails because of the race where the first IRQ is dropped on the floor (after hid_device_io_start() happens, but before the 50ms timeout passess), and report descriptor never gets parsed and populated. As this is just a boot time micro-optimization, let's revert the patch for 5.9 now, and fix this properly eventually for next merge window. Link: https://bugzilla.kernel.org/show_bug.cgi?id=208935 Reported-by: Johannes Hirte <johannes.hirte@datenkhaos.de> Reported-by: Marius Zachmann <mail@mariuszachmann.de> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2020-08-18drm/panel: Add panel driver for the Mantix MLAF057WE51-X DSI panelGuido Günther
The panel uses a Focaltech FT8006p, the touch part is handled by the already existing edt-ft5x06. Signed-off-by: Guido Günther <agx@sigxcpu.org> Reviewed-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/118c6e03dd0ff6e86e495579102cbf7d0cfca6f4.1597652012.git.agx@sigxcpu.org
2020-08-18RDMA/usnic: Fix spelling mistake "transistion" -> "transition"Colin Ian King
There is a spelling mistake in a usnic_err error message. Fix it. Link: https://lore.kernel.org/r/20200805141459.23069-1-colin.king@canonical.com Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
generated by cgit (git 2.34.1) at 2025-09-20 18:26:48 +0000