| Age | Commit message (Collapse) | Author |
|---|
|
When the user requests a high enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value of 0.
But according to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency. Adding 0
to the counter is a no-op. The data-sheet even explicitly states that
writing 0 to the base_unit bits will result in the PWM outputting a
continuous 0 signal.
When the user requestes a low enough period ns value, then the
calculations in pwm_lpss_prepare() might result in a base_unit value
which is bigger then base_unit_range - 1. Currently the codes for this
deals with this by applying a mask:
base_unit &= (base_unit_range - 1);
But this means that we let the value overflow the range, we throw away the
higher bits and store whatever value is left in the lower bits into the
register leading to a random output frequency, rather then clamping the
output frequency to the highest frequency which the hardware can do.
This commit fixes both issues by clamping the base_unit value to be
between 1 and (base_unit_range - 1).
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-5-hdegoede@redhat.com
|
|
According to the data-sheet the way the PWM controller works is that
each input clock-cycle the base_unit gets added to a N bit counter and
that counter overflowing determines the PWM output frequency.
So assuming e.g. a 16 bit counter this means that if base_unit is set to 1,
after 65535 input clock-cycles the counter has been increased from 0 to
65535 and it will overflow on the next cycle, so it will overflow after
every 65536 clock cycles and thus the calculations done in
pwm_lpss_prepare() should use 65536 and not 65535.
This commit fixes this. Note this also aligns the calculations in
pwm_lpss_prepare() with those in pwm_lpss_get_state().
Note this effectively reverts commit 684309e5043e ("pwm: lpss: Avoid
potential overflow of base_unit"). The next patch in this series really
fixes the potential overflow of the base_unit value.
Fixes: 684309e5043e ("pwm: lpss: Avoid potential overflow of base_unit")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-4-hdegoede@redhat.com
|
|
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets turned off from the _PS3 method of the graphics-card dev:
Method (_PS3, 0, Serialized) // _PS3: Power State 3
{
...
PWMB = PWMC /* \_SB_.PCI0.GFX0.PWMC */
PSAT |= 0x03
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
...
}
Where PSAT is the power-status register of the PWM controller.
Since the i915 driver will do a pwm_get on the pwm device as it uses it to
control the LCD panel backlight, there is a device-link marking the i915
device as a consumer of the pwm device. So that the PWM controller will
always be suspended after the i915 driver suspends (which is the right
thing to do). This causes the above GFX0 PS3 AML code to run before
acpi_lpss.c calls acpi_lpss_save_ctx().
So on these devices the PWM controller will already be off when
acpi_lpss_save_ctx() runs. This causes it to read/save all 1-s (0xffffffff)
as ctx register values.
When these bogus values get restored on resume the PWM controller actually
keeps working, since most bits are reserved, but this does set bit 3 of
the LPSS General purpose register, which for the PWM controller has the
following function: "This bit is re-used to support 32kHz slow mode.
Default is 19.2MHz as PWM source clock".
This causes the clock of the PWM controller to switch from 19.2MHz to
32KHz, which is a slow-down of a factor 600. Surprisingly enough so far
there have been few bug reports about this. This is likely because the
i915 driver was hardcoding the PWM frequency to 46 KHz, which divided
by 600 would result in a PWM frequency of approx. 78 Hz, which mostly
still works fine. There are some bug reports about the LCD backlight
flickering after suspend/resume which are likely caused by this issue.
But with the upcoming patch-series to finally switch the i915 drivers
code for external PWM controllers to use the atomic API and to honor
the PWM frequency specified in the video BIOS (VBT), this becomes a much
bigger problem. On most cases the VBT specifies either 200 Hz or 20
KHz as PWM frequency, which with the mentioned issue ends up being either
1/3 Hz, where the backlight actually visible blinks on and off every 3s,
or in 33 Hz and horrible flickering of the backlight.
There are a number of possible solutions to this problem:
1. Make acpi_lpss_save_ctx() run before GFX0._PS3
Pro: Clean solution from pov of not medling with save/restore ctx code
Con: As mentioned the current ordering is the right thing to do
Con: Requires assymmetry in at what suspend/resume phase we do the save vs
restore, requiring more suspend/resume ordering hacks in already
convoluted acpi_lpss.c suspend/resume code.
2. Do some sort of save once mode for the LPSS ctx
Pro: Reasonably clean
Con: Needs a new LPSS flag + code changes to handle the flag
3. Detect we have failed to save the ctx registers and do not restore them
Pro: Not PWM specific, might help with issues on other LPSS devices too
Con: If we can get away with not restoring the ctx why bother with it at
all?
4. Do not save the ctx for CHT PWM controllers
Pro: Clean, as simple as dropping a flag?
Con: Not so simple as dropping a flag, needs a new flag to ensure that
we still do lpss_deassert_reset() on device activation.
5. Make the pwm-lpss code fixup the LPSS-context registers
Pro: Keeps acpi_lpss.c code clean
Con: Moves knowledge of LPSS-context into the pwm-lpss.c code
1 and 5 both do not seem to be a desirable way forward.
3 and 4 seem ok, but they both assume that restoring the LPSS-context
registers is not necessary. I have done a couple of test and those do
show that restoring the LPSS-context indeed does not seem to be necessary
on devices using s2idle suspend (and successfully reaching S0i3). But I
have no hardware to test deep / S3 suspend. So I'm not sure that not
restoring the context is safe.
That leaves solution 2, which is about as simple / clean as 3 and 4,
so this commit fixes the described problem by implementing a new
LPSS_SAVE_CTX_ONCE flag and setting that for the CHT PWM controllers.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-3-hdegoede@redhat.com
|
|
The DSDTs on most Cherry Trail devices have an ugly clutch where the PWM
controller gets poked from the _PS0 method of the graphics-card device:
Local0 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
If (((Local0 & 0x03) == 0x03))
{
PSAT &= 0xFFFFFFFC
Local1 = PSAT /* \_SB_.PCI0.GFX0.PSAT */
RSTA = Zero
RSTF = Zero
RSTA = One
RSTF = One
PWMB |= 0xC0000000
PWMC = PWMB /* \_SB_.PCI0.GFX0.PWMB */
}
Where PSAT is the power-status register of the PWM controller, so if it
is in D3 when the GFX0 device's PS0 method runs then it will turn it on
and restore the PWM ctrl register value it saved from its PS3 handler.
Note not only does it restore it, it ors it with 0xC0000000 turning it
on at a time where we may not want it to get turned on at all.
The pwm_get call which the i915 driver does to get a reference to the
PWM controller, already adds a device-link making the GFX0 device a
consumer of the PWM device. So it should already have been resumed when
the above AML runs and the AML should thus not do its undesirable poking
of the PWM controller register.
But the PCI core powers on PCI devices in the no-irq resume phase and
thus calls the troublesome PS0 method in the no-irq resume phase.
Where as LPSS devices by default are resumed in the early resume phase.
This commit sets the resume_from_noirq flag in the bsw_pwm_dev_desc
struct, so that Cherry Trail PWM controllers will be resumed in the
no-irq phase. Together with the device-link added by the pwm-get this
ensures that the PWM controller will be on when the troublesome PS0
method runs, which stops it from poking the PWM controller.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200903112337.4113-2-hdegoede@redhat.com
|
|
'clang-format-for-linus-v5.9-rc4' and 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux
Pull misc fixes from Miguel Ojeda:
"A trivial patch for auxdisplay:
- Replace HTTP links with HTTPS ones (Alexander A. Klimov)
The usual clang-format trivial update:
- Update with the latest for_each macro list (Miguel Ojeda)
And Luc requested me to pick a sparse fix on my queue, so here it goes
along with other two trivial Compiler Attributes ones (also from Luc).
- sparse: use static inline for __chk_{user,io}_ptr() (Luc Van
Oostenryck)
- Compiler Attributes: fix comment concerning GCC 4.6 (Luc Van
Oostenryck)
- Compiler Attributes: remove comment about sparse not supporting
__has_attribute (Luc Van Oostenryck)"
* tag 'auxdisplay-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
auxdisplay: Replace HTTP links with HTTPS ones
* tag 'clang-format-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
clang-format: Update with the latest for_each macro list
* tag 'compiler-attributes-for-linus-v5.9-rc4' of git://github.com/ojeda/linux:
sparse: use static inline for __chk_{user,io}_ptr()
Compiler Attributes: fix comment concerning GCC 4.6
Compiler Attributes: remove comment about sparse not supporting __has_attribute
|
|
The dpsub driver uses the DMA engine API, and thus selects DMA_ENGINE to
provide that API. DMA_ENGINE depends on DMADEVICES, which can be
deselected by the user, creating a possibly unmet indirect dependency:
WARNING: unmet direct dependencies detected for DMA_ENGINE
Depends on [n]: DMADEVICES [=n]
Selected by [m]:
- DRM_ZYNQMP_DPSUB [=m] && HAS_IOMEM [=y] && (ARCH_ZYNQMP || COMPILE_TEST [=y]) && COMMON_CLK [=y] && DRM [=m] && OF [=y]
Add a dependency on DMADEVICES to fix this.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
|
|
Enabling a whole subsystem from a single driver 'select' is frowned
upon and won't be accepted in new drivers, that need to use 'depends on'
instead. Existing selection of DMAENGINES will then cause circular
dependencies. Replace them with a dependency.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
|
|
The upstream S6E63M0 driver has some peculiarities around
the prepare/enable disable/unprepare sequence: the screen
is taken out of sleep in prepare() as part of
s6e63m0_init() the put to on with MIPI_DCS_SET_DISPLAY_ON
in enable().
However it is just put into sleep mode directly in
disable(). As disable()/enable() can be called without
unprepare()/prepare() being called, this is unbalanced,
we should take the display out of sleep in enable()
then turn it off().
Further MIPI_DCS_SET_DISPLAY_OFF is never called
balanced with MIPI_DCS_SET_DISPLAY_ON.
The vendor driver for Samsung GT-I8190 (Golden) does all
of these things in strict order.
Augment the driver to do exit sleep/set display on in
enable() and set display off/enter sleep in disable().
Further send an explicit reset pulse in power_on() so we
come up in a known state, and issue the MCS_ERROR_CHECK
command after setting display on like the vendor driver
does. Also use the timings from the vendor driver in
the sequence.
Doing all of these things makes the display much more
stable on the Samsung GT-I8190 when enabling/disabling
the display pipeline.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200817213906.88207-1-linus.walleij@linaro.org
|
|
We add code to identify a few different panels mounted
on the s6e63m0 controller. This is necessary to achieve
the proper biasing with DSI versions of the panel.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809215104.1830206-5-linus.walleij@linaro.org
|
|
This adds code to send read commands to read a single
byte from the display, in order to perform MTP ID
look-up of the mounted panel on the s6e63m0 controller.
This is needed for proper biasing on the DSI variants.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809215104.1830206-4-linus.walleij@linaro.org
|
|
This makes it possible to use the s6e63m0 panel with a
DSI host, such as in the Samsung GT-I8190 (Golden) mobile
phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20200809215104.1830206-3-linus.walleij@linaro.org
|
|
This panel can be accessed using both SPI and DSI.
To make it possible to probe and use the device also from
a DSI bus, first break out the SPI support to its own file.
Since all the panel driver does is write DCS commands to
the panel, we pass a DCS write function to probe()
from each subdriver.
We make the Kconfig entry for SPI mode default so all
current users will continue to work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Cc: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/384873/
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix reference counting in the operating performance points (OPP)
framework and address a few intel_pstate driver issues, mostly related
to switching driver operation modes and similar with hardware-managed
P-states (HWP) enabled.
Specifics:
- Fix reference counting of operating performance points (OPP) tables
(Viresh Kumar).
- Address intel_pstate driver interface issues, mostly related to
switching operation modes and handling CPU offline and online and
system-wide suspend/resume with hardware-managed P-states (HWP)
enabled (Rafael Wysocki).
- Fix the maximum frequency computation in the intel_pstate driver
with turbo P-states disabled by the platform firmware and HWP
enabled (Francisco Jerez)"
* tag 'pm-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: intel_pstate: Fix intel_pstate_get_hwp_max() for turbo disabled
cpufreq: intel_pstate: Free memory only when turning off
cpufreq: intel_pstate: Add ->offline and ->online callbacks
cpufreq: intel_pstate: Tweak the EPP sysfs interface
cpufreq: intel_pstate: Update cached EPP in the active mode
cpufreq: intel_pstate: Refuse to turn off with HWP enabled
opp: Don't drop reference for an OPP table that was never parsed
|
|
Pull libata fixes from Jens Axboe:
- improve Sandisks ATA_HORKAGE on NCQ (Tejun)
- link printk cleanup (Xu)
* tag 'libata-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
libata: implement ATA_HORKAGE_MAX_TRIM_128M and apply to Sandisks
ata: ahci: use ata_link_info() instead of ata_link_printk()
|
|
Pull block fixes from Jens Axboe:
"A bit larger than usual this week, mostly due to the NVMe fixes
arriving late for -rc3 and hence didn't make last weeks pull request.
- NVMe:
- instance leak and io boundary fixes from Keith
- fc locking fix from Christophe
- various tcp/rdma reset during traffic fixes from Sagi
- pci use-after-free fix from Tong
- tcp target null deref fix from Ziye
- Locking fix for partition removal (Christoph)
- Ensure bdi->io_pages is always set (me)
- Fixup for hd struct reference (Ming)
- Fix for zero length bvecs (Ming)
- Two small blk-iocost fixes (Tejun)"
* tag 'block-5.9-2020-09-04' of git://git.kernel.dk/linux-block:
block: allow for_each_bvec to support zero len bvec
blk-stat: make q->stats->lock irqsafe
blk-iocost: ioc_pd_free() shouldn't assume irq disabled
block: fix locking in bdev_del_partition
block: release disk reference in hd_struct_free_work
block: ensure bdi->io_pages is always initialized
nvme-pci: cancel nvme device request before disabling
nvme: only use power of two io boundaries
nvme: fix controller instance leak
nvmet-fc: Fix a missed _irqsave version of spin_lock in 'nvmet_fc_fod_op_done()'
nvme: Fix NULL dereference for pci nvme controllers
nvme-rdma: fix reset hang if controller died in the middle of a reset
nvme-rdma: fix timeout handler
nvme-rdma: serialize controller teardown sequences
nvme-tcp: fix reset hang if controller died in the middle of a reset
nvme-tcp: fix timeout handler
nvme-tcp: serialize controller teardown sequences
nvme: have nvme_wait_freeze_timeout return if it timed out
nvme-fabrics: don't check state NVME_CTRL_NEW for request acceptance
nvmet-tcp: Fix NULL dereference when a connect data comes in h2cdata pdu
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixes from Daniel Lezcano:
- Fix bogus thermal shutdowns for omap4430 where bogus values resulting
from an incorrect ADC conversion are too high and fire an emergency
shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
* tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Fix use-after-free in thermal_zone_device_unregister()
thermal: qcom-spmi-temp-alarm: Don't suppress negative temp
thermal: ti-soc-thermal: Fix bogus thermal shutdowns for omap4430
|
|
Disable the RPTR shadow across all targets. It will be selectively
re-enabled later for targets that need it.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Temporarily disable preemption on a5xx targets pending some improvements
to protect the RPTR shadow from being corrupted.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
a650 supports expanded apriv support that allows us to map critical buffers
(ringbuffer and memstore) as as privileged to protect them from corruption.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The main a5xx preemption record can be marked as privileged to
protect it from user access but the counters storage needs to be
remain unprivileged. Split the buffers and mark the critical memory
as privileged.
Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A couple of core fixes and odd driver fixes for dmaengine subsystem:
Core:
- drop ACPI CSRT table reference after using it
- fix of_dma_router_xlate() error handling
Drivers fixes in idxd, at_hdmac, pl330, dw-edma and jz478"
* tag 'dmaengine-fix-5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: ti: k3-udma: Update rchan_oes_offset for am654 SYSFW ABI 3.0
drivers/dma/dma-jz4780: Fix race condition between probe and irq handler
dmaengine: dw-edma: Fix scatter-gather address calculation
dmaengine: ti: k3-udma: Fix the TR initialization for prep_slave_sg
dmaengine: pl330: Fix burst length if burst size is smaller than bus width
dmaengine: at_hdmac: add missing kfree() call in at_dma_xlate()
dmaengine: at_hdmac: add missing put_device() call in at_dma_xlate()
dmaengine: at_hdmac: check return value of of_find_device_by_node() in at_dma_xlate()
dmaengine: of-dma: Fix of_dma_router_xlate's of_dma_xlate handling
dmaengine: idxd: reset states after device disable or reset
dmaengine: acpi: Put the CSRT table after using it
|
|
Pull drm fixes from Dave Airlie:
"Not much going on this week, nouveau has a display hw bug workaround,
amdgpu has some PM fixes and CIK regression fixes, one single radeon
PLL fix, and a couple of i915 display fixes.
amdgpu:
- Fix for 32bit systems
- SW CTF fix
- Update for Sienna Cichlid
- CIK bug fixes
radeon:
- PLL fix
i915:
- Clang build warning fix
- HDCP fixes
nouveau:
- display fixes"
* tag 'drm-fixes-2020-09-04' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/kms/nv50-gp1xx: add WAR for EVO push buffer HW bug
drm/nouveau/kms/nv50-gp1xx: disable notifies again after core update
drm/nouveau/kms/nv50-: add some whitespace before debug message
drm/nouveau/kms/gv100-: Include correct push header in crcc37d.c
drm/radeon: Prefer lower feedback dividers
drm/amdgpu: Fix bug in reporting voltage for CIK
drm/amdgpu: Specify get_argument function for ci_smu_funcs
drm/amd/pm: enable MP0 DPM for sienna_cichlid
drm/amd/pm: avoid false alarm due to confusing softwareshutdowntemp setting
drm/amd/pm: fix is_dpm_running() run error on 32bit system
drm/i915: Clear the repeater bit on HDCP disable
drm/i915: Fix sha_text population code
drm/i915/display: Ensure that ret is always initialized in icl_combo_phy_verify_state
|
|
Merge emailed patches from Peter Xu:
"This is a small series that I picked up from Linus's suggestion to
simplify cow handling (and also make it more strict) by checking
against page refcounts rather than mapcounts.
This makes uffd-wp work again (verified by running upmapsort)"
Note: this is horrendously bad timing, and making this kind of
fundamental vm change after -rc3 is not at all how things should work.
The saving grace is that it really is a a nice simplification:
8 files changed, 29 insertions(+), 120 deletions(-)
The reason for the bad timing is that it turns out that commit
17839856fd58 ("gup: document and work around 'COW can break either way'
issue" broke not just UFFD functionality (as Peter noticed), but Mikulas
Patocka also reports that it caused issues for strace when running in a
DAX environment with ext4 on a persistent memory setup.
And we can't just revert that commit without re-introducing the original
issue that is a potential security hole, so making COW stricter (and in
the process much simpler) is a step to then undoing the forced COW that
broke other uses.
Link: https://lore.kernel.org/lkml/alpine.LRH.2.02.2009031328040.6929@file01.intranet.prod.int.rdu2.redhat.com/
* emailed patches from Peter Xu <peterx@redhat.com>:
mm: Add PGREUSE counter
mm/gup: Remove enfornced COW mechanism
mm/ksm: Remove reuse_ksm_page()
mm: do_wp_page() simplification
|
|
* pm-cpufreq:
cpufreq: intel_pstate: Fix intel_pstate_get_hwp_max() for turbo disabled
cpufreq: intel_pstate: Free memory only when turning off
cpufreq: intel_pstate: Add ->offline and ->online callbacks
cpufreq: intel_pstate: Tweak the EPP sysfs interface
cpufreq: intel_pstate: Update cached EPP in the active mode
cpufreq: intel_pstate: Refuse to turn off with HWP enabled
|
|
With the more strict (but greatly simplified) page reuse logic in
do_wp_page(), we can safely go back to the world where cow is not
enforced with writes.
This essentially reverts commit 17839856fd58 ("gup: document and work
around 'COW can break either way' issue"). There are some context
differences due to some changes later on around it:
2170ecfa7688 ("drm/i915: convert get_user_pages() --> pin_user_pages()", 2020-06-03)
376a34efa4ee ("mm/gup: refactor and de-duplicate gup_fast() code", 2020-06-03)
Some lines moved back and forth with those, but this revert patch should
have striped out and covered all the enforced cow bits anyways.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This commit fixes two issues:
1. The lockdep warning reported by Dong Aisheng <dongas86@gmail.com> [1].
It is a warning about a cycle (dpm_list_mtx --> kn->active#3 --> fw_lock)
that was introduced when device-link devices were added to expose device
link information in sysfs.
The patch that "introduced" this cycle can't be reverted because it's fixes
a real SRCU issue and also ensures that the device-link device is deleted
as soon as the device-link is deleted. This is important to avoid sysfs
name collisions if the device-link is create again immediately (this can
happen a lot with deferred probing).
2. Inconsistency in grabbing device_pm_lock() during device link deletion
Some device link deletion code paths grab device_pm_lock(), while others
don't. The device_pm_lock() is grabbed during device_link_add() because it
checks if the supplier is in the dpm_list and also reorders the dpm_list.
However, when a device link is deleted, it does not do either of those and
therefore device_pm_lock() is not necessary. Dropping the device_pm_lock()
in all the device link deletion paths removes the inconsistency in locking.
Thanks to Stephen Boyd for helping me understand the lockdep splat.
Fixes: 843e600b8a2b ("driver core: Fix sleeping in invalid context during device link deletion")
[1] - https://lore.kernel.org/lkml/CAA+hA=S4eAreb7vo69LAXSk2t5=DEKNxHaiY1wSpk4xTp9urLg@mail.gmail.com/
Reported-by: Dong Aisheng <dongas86@gmail.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200901184445.1736658-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dev_err_probe() prepends the message with an error code. Let's make it
more readable by translating the code to a more recognisable symbol.
Fixes: a787e5400a1c ("driver core: add device probe log helper")
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/ea3f973e4708919573026fdce52c264db147626d.1598630856.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzbot is reporting OOB read at vga_8planes_imageblit() [1], for
"cdat[y] >> 4" can become a negative value due to "const char *cdat".
[1] https://syzkaller.appspot.com/bug?id=0d7a0da1557dcd1989e00cb3692b26d4173b4132
Reported-by: syzbot <syzbot+69fbd3e01470f169c8c4@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/90b55ec3-d5b0-3307-9f7c-7ff5c5fd6ad3@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB device descriptor may get changed between two consecutive
enumerations on the same device for some reason, such as DFU or
malicius device.
In that case, we may access the changing descriptor if we don't take
the device lock here.
The issue is reported:
https://syzkaller.appspot.com/bug?id=901a0d9e6519ef8dc7acab25344bd287dd3c7be9
Cc: stable <stable@vger.kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+256e56ddde8b8957eabd@syzkaller.appspotmail.com
Fixes: 217a9081d8e6 ("USB: add all configs to the "descriptors" attribute")
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Link: https://lore.kernel.org/r/1599201467-11000-1-git-send-email-prime.zeng@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 7a410953d1fb4dbe91ffcfdee9cbbf889d19b0d7.
This commit breaks USB on meson-gxl-s905x-libretech-cc. Reverting
the change solves the issue.
In fact, according to the reset framework code, consumers must not use
reset_control_(de)assert() on shared reset lines when reset_control_reset
has been used, and vice-versa.
Moreover, with this commit, usb is not guaranted to be reset since the
reset is likely to be initially deasserted.
Reverting the commit will bring back the suspend warning mentioned in the
commit description. Nevertheless, a warning is much less critical than
breaking dwc3-meson-g12a USB completely. We will address the warning
issue in another way as a 2nd step.
Fixes: 7a410953d1fb ("usb: dwc3: meson-g12a: fix shared reset control use")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reported-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200827144810.26657-1-aouledameur@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Failing probe with -EPROBE_DEFER until all dependencies
listed in the _DEP (Operation Region Dependencies) object
have been met.
This will fix an issue where on some platforms UCSI ACPI
driver fails to probe because the address space handler for
the operation region that the UCSI ACPI interface uses has
not been loaded yet.
Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200904110918.51546-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added missing code for un-register USB role switch in the remove and
error path.
Cc: Stable <stable@vger.kernel.org> # v5.8
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Fixes: 6701adfa9693b ("usb: typec: driver for Intel PMC mux control")
Signed-off-by: Madhusudanarao Amara <madhusudanarao.amara@intel.com>
Link: https://lore.kernel.org/r/20200825183811.7262-1-madhusudanarao.amara@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Userspace drivers that use a SetConfiguration() request to "lightweight"
reset an already configured usb device might cause data toggles to get out
of sync between the device and host, and the device becomes unusable.
The xHCI host requires endpoints to be dropped and added back to reset the
toggle. If USB core notices the new configuration is the same as the
current active configuration it will avoid these extra steps by calling
usb_reset_configuration() instead of usb_set_configuration().
A SetConfiguration() request will reset the device side data toggles.
Make sure usb_reset_configuration() function also drops and adds back the
endpoints to ensure data toggles are in sync.
To avoid code duplication split the current usb_disable_device() function
and reuse the endpoint specific part.
Cc: stable <stable@vger.kernel.org>
Tested-by: Martin Thierer <mthierer@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200901082528.12557-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
into char-misc-linus
Georgi writes:
interconnect fixes for v5.9
This contains two fixes:
- Fix the core to show correctly the bandwidth for disabled paths.
- Fix a driver to make sure small values are not truncated.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
* tag 'icc-5.9-rc4' of https://git.linaro.org/people/georgi.djakov/linux:
interconnect: qcom: Fix small BW votes being truncated to zero
interconnect: Show bandwidth for disabled paths as zero in debugfs
|
|
Not needed, already tracked by drm_crtc_state->active.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20200818072511.6745-3-kraxel@redhat.com
(cherry picked from commit 1174c8a0f33c1e5c442ac40381fe124248c08b3a)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-linus
Vinod writes:
phy: fixes for 5.9
*) platform_no_drv_owner.cocci and return value check qcom ipq806x-usb driver
*) correcting register programming for ipq8074 phy
*) disable PHY charger detect for omap-usb2-phy
* tag 'phy-fixes-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: omap-usb2-phy: disable PHY charger detect
phy: qcom-qmp: Use correct values for ipq8074 PCIe Gen2 PHY init
phy: qualcomm: fix return value check in qcom_ipq806x_usb_phy_probe()
phy: qualcomm: fix platform_no_drv_owner.cocci warnings
|
|
Streamline the modeset init by removing the extra init layer.
No functional changes, which means the cleanup path looks hideous.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/62c32c35683b843ecdc2eca2bd2d3e62cb705e96.1599056955.git.jani.nikula@intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
soundwire fixes for v5.8
This contains two fixes to sdw core for dangling pointer and a typo for
INTSTAT register
* tag 'soundwire-5.9-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: fix double free of dangling pointer
soundwire: bus: fix typo in comment on INTSTAT registers
|
|
Split out a separate display function for driver remove after gem
deinitialization. Note that the sequence is not symmetric with
init. However use similar naming as that reflects the deinit sequence.
No functional changes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/197fa7e488b412e147ff0fe9440c48811888f1a6.1599056955.git.jani.nikula@intel.com
|
|
With the intel_modeset_* probe functions clarified, we can continue with
moving more related calls to the right layer:
- drm_vblank_init()
- intel_bios_init()
- intel_vga_register()
- intel_csr_ucode_init()
Unfortunately, for the time being, we also need to move a call to the
*wrong* layer: the power domain init.
No functional changes.
v2: move probe failure while at it, power domain init
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/da229ffbed64983f002605074533c8b2878d17ee.1599056955.git.jani.nikula@intel.com
|
|
Turn current intel_modeset_init() to a pre-gem init function, and add a
new intel_modeset_init() function and move all post-gem modeset init
there, in the correct layer. No functional changes.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/5f4603f2c0216dba980338f00e0bfa791b526231.1599056955.git.jani.nikula@intel.com
|
|
Beware that the address size for x86-32 may exceed unsigned long.
[ 0.368971] UBSAN: shift-out-of-bounds in drivers/iommu/intel/iommu.c:128:14
[ 0.369055] shift exponent 36 is too large for 32-bit type 'long unsigned int'
If we don't handle the wide addresses, the pages are mismapped and the
device read/writes go astray, detected as DMAR faults and leading to
device failure. The behaviour changed (from working to broken) in commit
fa954e683178 ("iommu/vt-d: Delegate the dma domain to upper layer"), but
the error looks older.
Fixes: fa954e683178 ("iommu/vt-d: Delegate the dma domain to upper layer")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Cc: James Sewart <jamessewart@arista.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: <stable@vger.kernel.org> # v5.3+
Link: https://lore.kernel.org/r/20200822160209.28512-1-chris@chris-wilson.co.uk
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When memory encryption is active the device is likely not in a direct
mapped domain. Forbid using IOMMUv2 functionality for now until finer
grained checks for this have been implemented.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200824105415.21000-3-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Do not force devices supporting IOMMUv2 to be direct mapped when memory
encryption is active. This might cause them to be unusable because their
DMA mask does not include the encryption bit.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Link: https://lore.kernel.org/r/20200824105415.21000-2-joro@8bytes.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When using 128-bit interrupt-remapping table entry (IRTE) (a.k.a GA mode),
current driver disables interrupt remapping when it updates the IRTE
so that the upper and lower 64-bit values can be updated safely.
However, this creates a small window, where the interrupt could
arrive and result in IO_PAGE_FAULT (for interrupt) as shown below.
IOMMU Driver Device IRQ
============ ===========
irte.RemapEn=0
...
change IRTE IRQ from device ==> IO_PAGE_FAULT !!
...
irte.RemapEn=1
This scenario has been observed when changing irq affinity on a system
running I/O-intensive workload, in which the destination APIC ID
in the IRTE is updated.
Instead, use cmpxchg_double() to update the 128-bit IRTE at once without
disabling the interrupt remapping. However, this means several features,
which require GA (128-bit IRTE) support will also be affected if cmpxchg16b
is not supported (which is unprecedented for AMD processors w/ IOMMU).
Fixes: 880ac60e2538 ("iommu/amd: Introduce interrupt remapping ops structure")
Reported-by: Sean Osborne <sean.m.osborne@oracle.com>
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Erik Rockstrom <erik.rockstrom@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/20200903093822.52012-3-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Currently, the RemapEn (valid) bit is accidentally cleared when
programming IRTE w/ guestMode=0. It should be restored to
the prior state.
Fixes: b9fc6b56f478 ("iommu/amd: Implements irq_set_vcpu_affinity() hook to setup vapic mode for pass-through devices")
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Link: https://lore.kernel.org/r/20200903093822.52012-2-suravee.suthikulpanit@amd.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The user-after-free bug in thermal_zone_device_unregister() is reported by
KASAN. It happens because struct thermal_zone_device is released during of
device_unregister() invocation, and hence the "tz" variable shouldn't be
touched by thermal_notify_tz_delete(tz->id).
Fixes: 55cdf0a283b8 ("thermal: core: Add notifications call in the framework")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200817235854.26816-1-digetx@gmail.com
|
|
Currently driver is suppressing the negative temperature
readings from the vadc. Consumers of the thermal zones need
to read the negative temperature too. Don't suppress the
readings.
Fixes: c610afaa21d3c6e ("thermal: Add QPNP PMIC temperature alarm driver")
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/944856eb819081268fab783236a916257de120e4.1596040416.git.gurus@codeaurora.org
|
|
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54d7 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
|
|
The dev_iommu_priv_set() must be called after probe_device(). This fixes
a NULL pointer deference bug when booting a system with kernel cmdline
"intel_iommu=on,igfx_off", where the dev_iommu_priv_set() is abused.
The following stacktrace was produced:
Command line: BOOT_IMAGE=/isolinux/bzImage console=tty1 intel_iommu=on,igfx_off
...
DMAR: Host address width 39
DMAR: DRHD base: 0x000000fed90000 flags: 0x0
DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap 1c0000c40660462 ecap 19e2ff0505e
DMAR: DRHD base: 0x000000fed91000 flags: 0x1
DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008c40660462 ecap f050da
DMAR: RMRR base: 0x0000009aa9f000 end: 0x0000009aabefff
DMAR: RMRR base: 0x0000009d000000 end: 0x0000009f7fffff
DMAR: No ATSR found
BUG: kernel NULL pointer dereference, address: 0000000000000038
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] SMP PTI
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.9.0-devel+ #2
Hardware name: LENOVO 20HGS0TW00/20HGS0TW00, BIOS N1WET46S (1.25s ) 03/30/2018
RIP: 0010:intel_iommu_init+0xed0/0x1136
Code: fe e9 61 02 00 00 bb f4 ff ff ff e9 57 02 00 00 48 63 d1 48 c1 e2 04 48
03 50 20 48 8b 12 48 85 d2 74 0b 48 8b 92 d0 02 00 00 48 89 7a 38 ff c1
e9 15 f5 ff ff 48 c7 c7 60 99 ac a7 49 c7 c7 a0
RSP: 0000:ffff96d180073dd0 EFLAGS: 00010282
RAX: ffff8c91037a7d20 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffffffffffffff
RBP: ffff96d180073e90 R08: 0000000000000001 R09: ffff8c91039fe3c0
R10: 0000000000000226 R11: 0000000000000226 R12: 000000000000000b
R13: ffff8c910367c650 R14: ffffffffa8426d60 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff8c9107480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000038 CR3: 00000004b100a001 CR4: 00000000003706e0
Call Trace:
? _raw_spin_unlock_irqrestore+0x1f/0x30
? call_rcu+0x10e/0x320
? trace_hardirqs_on+0x2c/0xd0
? rdinit_setup+0x2c/0x2c
? e820__memblock_setup+0x8b/0x8b
pci_iommu_init+0x16/0x3f
do_one_initcall+0x46/0x1e4
kernel_init_freeable+0x169/0x1b2
? rest_init+0x9f/0x9f
kernel_init+0xa/0x101
ret_from_fork+0x22/0x30
Modules linked in:
CR2: 0000000000000038
---[ end trace 3653722a6f936f18 ]---
Fixes: 01b9d4e21148c ("iommu/vt-d: Use dev_iommu_priv_get/set()")
Reported-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Reported-by: Wendy Wang <wendy.wang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Tested-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Link: https://lore.kernel.org/linux-iommu/96717683-70be-7388-3d2f-61131070a96a@secunet.com/
Link: https://lore.kernel.org/r/20200903065132.16879-1-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
