| Age | Commit message (Collapse) | Author |
|---|
|
sop_drop_qpn field in the cqe is used by two features, in SWITCHDEV mode
to restore the chain id in case of a miss and in LEGACY mode to support
skbedit mark action. In build RX skb, the skb mark field is set regardless
of the configured mode which cause a corruption of the mark field in case
of switchdev mode.
Fix by overriding the mark value back to 0 in the representor tc update
skb flow.
Fixes: 8f1e0b97cc70 ("net/mlx5: E-Switch, Mark miss packets with new chain id mapping")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Raed Salem <raeds@nvidia.com>
Reviewed-by: Oz Shlomo <ozsh@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Adding vf VLANID for the first time, or after having cleared previously
defined VLANID works fine, however, attempting to change an existing vf
VLANID clears the rules on the firmware, but does not add new rules for
the new vf VLANID.
Fix this by changing the logic in function esw_acl_egress_lgcy_setup()
so that it will always configure egress rules.
Fixes: ea651a86d468 ("net/mlx5: E-Switch, Refactor eswitch egress acl codes")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In case WQE includes inline header the vlan is inserted by driver even
if vlan offload is set. On geneve over vlan interface where software
parser is used the SWP offsets should be updated according to the added
vlan.
Fixes: e3cfc7e6b7bd ("net/mlx5e: TX, Add geneve tunnel stateless offload support")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Connection counters may be shared for both directions when the counter
is used for connection aging purposes. However, if TC flow
accounting is enabled then a unique counter is required per direction.
Instantiate a unique counter per direction if the conntrack accounting
extension is enabled. Use a shared counter when the connection accounting
extension is disabled.
Fixes: 1edae2335adf ("net/mlx5e: CT: Use the same counter for both directions")
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In multi-port mode, FW reports syndrome 0x2ea48 (invalid vhca_port_number)
if the port_num is not 1 or 2.
Fixes: 80f09dfc237f ("net/mlx5: Eswitch, enable RoCE loopback traffic")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Expose firmware indication that it supports setting eswitch uplink state
to follow (follow the physical link). Condition setting the eswitch
uplink admin-state with this capability bit. Older FW may not support
the uplink state setting.
Fixes: 7d0314b11cdd ("net/mlx5e: Modify uplink state on interface up/down")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This patch fixes a memleak issue by preventing to create a lag and
add PFs if lag is not supported.
comm “python3”, pid 349349, jiffies 4296985507 (age 1446.976s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …………….
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 …………….
backtrace:
[<000000005b216ae7>] mlx5_lag_add+0x1d5/0×3f0 [mlx5_core]
[<000000000445aa55>] mlx5e_nic_enable+0x66/0×1b0 [mlx5_core]
[<00000000c56734c3>] mlx5e_attach_netdev+0x16e/0×200 [mlx5_core]
[<0000000030439d1f>] mlx5e_attach+0x5c/0×90 [mlx5_core]
[<0000000018fd8615>] mlx5e_add+0x1a4/0×410 [mlx5_core]
[<0000000068bc504b>] mlx5_add_device+0x72/0×120 [mlx5_core]
[<000000009fce51f9>] mlx5_register_device+0x77/0xb0 [mlx5_core]
[<00000000d0d81ff3>] mlx5_load_one+0xc58/0×1eb0 [mlx5_core]
[<0000000045077adc>] init_one+0x3ea/0×920 [mlx5_core]
[<0000000043287674>] pci_device_probe+0xcd/0×150
[<00000000dafd3279>] really_probe+0x1c9/0×4b0
[<00000000f06bdd84>] driver_probe_device+0x5d/0×140
[<00000000e3d508b6>] device_driver_attach+0x4f/0×60
[<0000000084fba0f0>] bind_store+0xbf/0×120
[<00000000bf6622b3>] kernfs_fop_write+0x114/0×1b0
Fixes: 9b412cc35f00 ("net/mlx5e: Add LAG warning if bond slave is not lag master")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Maor Gottlieb <maorg@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of core fixes here, both to do with handling of drivers which
don't report their maximum speed since we factored some of the
handling for transfer speeds out into the core in the previous
release.
There's also some driver specific fixes, including a relatively large
set for some races around timeouts in spi-geni-qcom"
* tag 'spi-fix-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: fix the divide by 0 error when calculating xfer waiting time
spi: Fix the clamping of spi->max_speed_hz
spi: altera: fix return value for altera_spi_txrx()
spi: stm32: FIFO threshold level - fix align packet size
spi: spi-geni-qcom: Print an error when we timeout setting the CS
spi: spi-geni-qcom: Don't try to set CS if an xfer is pending
spi: spi-geni-qcom: Fail new xfers if xfer/cancel/abort pending
spi: spi-geni-qcom: Fix geni_spi_isr() NULL dereference in timeout case
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few minor driver specific fixes, mostly DT bindings document bits,
plus a new device ID"
* tag 'regulator-fix-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: qcom-rpmh: add QCOM_COMMAND_DB dependency
regulator: qcom-rpmh-regulator: correct hfsmps515 definition
dt-bindings: regulator: qcom,rpmh-regulator: add pm8009 revision
regulator: bd718x7: Add enable times
regulator: pf8x00: Use specific compatible strings for devices
|
|
If usnic_ib_qp_grp_create() fails at the first call, dev_list
will not be freed on error, which leads to memleak.
Fixes: e3cf00d0a87f ("IB/usnic: Add Cisco VIC low-level hardware driver")
Link: https://lore.kernel.org/r/20201226074248.2893-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"A couple of small fixes for leaks when attaching a device to a
preexisting regmap"
* tag 'regmap-fix-v5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: debugfs: Fix a reversed if statement in regmap_debugfs_init()
regmap: debugfs: Fix a memory leak when calling regmap_attach_dev
|
|
Inconveniently devm_ioport_map() and devm_ioremap_resource()
return errors differently, i.e. former uses simply NULL pointer,
while the latter an error pointer.
Due to this, we have to check each of them separately.
Fixes: f104060813fe ("misc: pvpanic: Combine ACPI and platform drivers")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201228184313.57610-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xa_alloc_cyclic() call returns positive number if ID allocation
succeeded but wrapped. It is not an error, so normalize the "ret"
variable to zero as marker of not-an-error.
drivers/infiniband/core/restrack.c:261 rdma_restrack_add()
warn: 'ret' can be either negative or positive
Fixes: fd47c2f99f04 ("RDMA/restrack: Convert internal DB from hash to XArray")
Link: https://lore.kernel.org/r/20201216100753.1127638-1-leon@kernel.org
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Using this code on A5xx (and probably older too) causes a
smmu bug.
Fixes: 474dadb8b0d5 ("drm/msm/a6xx: Add support for using system cache(LLC)")
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
percent_fp() was used in intel_pstate_pid_reset(), which was removed in
commit 9d0ef7af1f2d ("cpufreq: intel_pstate: Do not use PID-based P-state
selection") and hence, percent_fp() is unused since then.
percent_ext_fp() was last used in intel_pstate_update_perf_limits(), which
was refactored in commit 1a4fe38add8b ("cpufreq: intel_pstate: Remove
max/min fractions to limit performance"), and hence, percent_ext_fp() is
unused since then.
make CC=clang W=1 points us those unused functions:
drivers/cpufreq/intel_pstate.c:79:23: warning: unused function 'percent_fp' [-Wunused-function]
static inline int32_t percent_fp(int percent)
^
drivers/cpufreq/intel_pstate.c:94:23: warning: unused function 'percent_ext_fp' [-Wunused-function]
static inline int32_t percent_ext_fp(int percent)
^
Remove those obsolete functions.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Using the GPU with a VRAM Carveout is a security vulnerability.
Nevertheless it is sometimes required, especially when no IOMMU
implementation is available for a certain platform.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
vram.size is needed when binding a gpu without an iommu and is defined
in msm_init_vram(), so run that before binding it.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Tested-by: Alexey Minnekhanov <alexeymin@postmarketos.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
irq_hpd event can only be executed at connected state. Therefore
irq_hpd event should be postponed if it happened at connection
pending state. This patch also make sure both link rate and lane
are valid before start link training.
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
There are only four valid fwnode cases which are
- primary --> secondary --> -ENODEV
- primary --> NULL
- secondary --> -ENODEV
- NULL
dev->fwnode should be converted between the 4 cases above no matter
how/when set_primary_fwnode() and set_secondary_fwnode() are called.
Describe it in the code so people will keep it in mind.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ rjw: Comment edit ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
While commit d5dcce0c414f ("device property: Keep secondary firmware
node secondary by type") describes everything correct in its commit
message, the change it made does the opposite and original commit
c15e1bdda436 ("device property: Fix the secondary firmware node handling
in set_primary_fwnode()") was fully correct.
Revert the former one here and improve documentation in the next patch.
Fixes: d5dcce0c414f ("device property: Keep secondary firmware node secondary by type")
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: 5.10+ <stable@vger.kernel.org> # 5.10+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The CONTAINER and HOTPLUG_MEMORY options mention modules but are bool
only, so if selected are always built in.
Drop the help text about modules.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Two local variables in drivers/acpi/x86/s2idle.c are never read, so
drop them along with the code updating their values (in vain).
Fixes: fef98671194b ("ACPI: PM: s2idle: Move x86-specific code to the x86 directory")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently there is an unlikely case where cpufreq_cpu_get() returns a
NULL policy and this will cause a NULL pointer dereference later on.
Fix this by passing the policy to transition_frequency_fidvid() from
the caller and hence eliminating the need for the cpufreq_cpu_get()
and cpufreq_cpu_put().
Thanks to Viresh Kumar for suggesting the fix.
Addresses-Coverity: ("Dereference null return")
Fixes: b43a7ffbf33b ("cpufreq: Notify all policy->cpus in cpufreq_notify_transition()")
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If turbo P-states cannot be used, either due to the configuration of
the processor, or because intel_pstate is not allowed to used them,
the maximum available P-state with HWP enabled corresponds to the
HWP_CAP.GUARANTEED value which is not static. It can be adjusted by
an out-of-band agent or during an Intel Speed Select performance
level change, so long as it remains less than or equal to
HWP_CAP.MAX.
However, if turbo P-states cannot be used, intel_cpufreq_adjust_perf()
always uses pstate.max_pstate (set during the initialization of the
driver only) as the maximum available P-state, so it may miss a change
of the HWP_CAP.GUARANTEED value.
Prevent that from happening by modifyig intel_cpufreq_adjust_perf()
to always read the "guaranteed" and "maximum turbo" performance
levels from the cached HWP_CAP value.
Fixes: a365ab6b9dfb ("cpufreq: intel_pstate: Implement the ->adjust_perf() callback")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
|
|
iommu_flush_dev_iotlb() is called to invalidate caches on a device but
only loops over the devices which are fully-attached to the domain. For
sub-devices, this is ineffective and can result in invalid caching
entries left on the device.
Fix the missing invalidation by adding a loop over the subdevices and
ensuring that 'domain->has_iotlb_device' is updated when attaching to
subdevices.
Fixes: 67b8e02b5e76 ("iommu/vt-d: Aux-domain specific domain attach/detach")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1609949037-25291-4-git-send-email-yi.l.liu@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The aux-domain attach/detach are not tracked, some data structures might
be used after free. This causes general protection faults when multiple
subdevices are created and assigned to a same guest machine:
| general protection fault, probably for non-canonical address 0xdead000000000100: 0000 [#1] SMP NOPTI
| RIP: 0010:intel_iommu_aux_detach_device+0x12a/0x1f0
| [...]
| Call Trace:
| iommu_aux_detach_device+0x24/0x70
| vfio_mdev_detach_domain+0x3b/0x60
| ? vfio_mdev_set_domain+0x50/0x50
| iommu_group_for_each_dev+0x4f/0x80
| vfio_iommu_detach_group.isra.0+0x22/0x30
| vfio_iommu_type1_detach_group.cold+0x71/0x211
| ? find_exported_symbol_in_section+0x4a/0xd0
| ? each_symbol_section+0x28/0x50
| __vfio_group_unset_container+0x4d/0x150
| vfio_group_try_dissolve_container+0x25/0x30
| vfio_group_put_external_user+0x13/0x20
| kvm_vfio_group_put_external_user+0x27/0x40 [kvm]
| kvm_vfio_destroy+0x45/0xb0 [kvm]
| kvm_put_kvm+0x1bb/0x2e0 [kvm]
| kvm_vm_release+0x22/0x30 [kvm]
| __fput+0xcc/0x260
| ____fput+0xe/0x10
| task_work_run+0x8f/0xb0
| do_exit+0x358/0xaf0
| ? wake_up_state+0x10/0x20
| ? signal_wake_up_state+0x1a/0x30
| do_group_exit+0x47/0xb0
| __x64_sys_exit_group+0x18/0x20
| do_syscall_64+0x57/0x1d0
| entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix the crash by tracking the subdevices when attaching and detaching
aux-domains.
Fixes: 67b8e02b5e76 ("iommu/vt-d: Aux-domain specific domain attach/detach")
Co-developed-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1609949037-25291-3-git-send-email-yi.l.liu@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
'struct intel_svm' is shared by all devices bound to a give process,
but records only a single pointer to a 'struct intel_iommu'. Consequently,
cache invalidations may only be applied to a single DMAR unit, and are
erroneously skipped for the other devices.
In preparation for fixing this, rework the structures so that the iommu
pointer resides in 'struct intel_svm_dev', allowing 'struct intel_svm'
to track them in its device list.
Fixes: 1c4f88b7f1f9 ("iommu/vt-d: Shared virtual address in scalable mode")
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: Raj Ashok <ashok.raj@intel.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Reported-by: Guo Kaijie <Kaijie.Guo@intel.com>
Reported-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Guo Kaijie <Kaijie.Guo@intel.com>
Signed-off-by: Xin Zeng <xin.zeng@intel.com>
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Tested-by: Guo Kaijie <Kaijie.Guo@intel.com>
Cc: stable@vger.kernel.org # v5.0+
Acked-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/1609949037-25291-2-git-send-email-yi.l.liu@intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
On SM8150 it's occasionally observed that the boot hangs in between the
writing of SMEs and context banks in arm_smmu_device_reset().
The problem seems to coincide with a display refresh happening after
updating the stream mapping, but before clearing - and there by
disabling translation - the context bank picked to emulate translation
bypass.
Resolve this by explicitly disabling the bypass context already in
cfg_probe.
Fixes: f9081b8ff593 ("iommu/arm-smmu-qcom: Implement S2CR quirk")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210106005038.4152731-1-bjorn.andersson@linaro.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Lock(&iommu->lock) without disabling irq causes lockdep warnings.
========================================================
WARNING: possible irq lock inversion dependency detected
5.11.0-rc1+ #828 Not tainted
--------------------------------------------------------
kworker/0:1H/120 just changed the state of lock:
ffffffffad9ea1b8 (device_domain_lock){..-.}-{2:2}, at:
iommu_flush_dev_iotlb.part.0+0x32/0x120
but this lock took another, SOFTIRQ-unsafe lock in the past:
(&iommu->lock){+.+.}-{2:2}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&iommu->lock);
local_irq_disable();
lock(device_domain_lock);
lock(&iommu->lock);
<Interrupt>
lock(device_domain_lock);
*** DEADLOCK ***
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201231005323.2178523-5-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
This reverts commit 65f746e8285f0a67d43517d86fedb9e29ead49f2.
As commit 8a473dbadccf ("drm/i915: Fix DMA mapped scatterlist walks") and
commit 934941ed5a30 ("drm/i915: Fix DMA mapped scatterlist lookup") fixed
the DMA scatterlist limitations in the i915 driver, remove this temporary
workaround.
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Tom Murphy <murphyt7@tcd.ie>
Cc: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201231005323.2178523-4-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Use IS_ALIGNED() instead. Otherwise, an unaligned address will be ignored.
Fixes: 33cd6e642d6a ("iommu/vt-d: Flush PASID-based iotlb for iova over first level")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20201231005323.2178523-1-baolu.lu@linux.intel.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Drivers are not supposed to use this directly any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Link: https://patchwork.freedesktop.org/patch/412156/
|
|
Drivers are not supposed to init the page pool directly any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Link: https://patchwork.freedesktop.org/patch/412153/
|
|
If an active transfer is dequeued, then the endpoint is freed to start a
new transfer. Make sure to clear the endpoint's transfer wait flag for
this case.
Fixes: e0d19563eb6c ("usb: dwc3: gadget: Wait for transfer completion")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b81cd5b5281cfbfdadb002c4bcf5c9be7c017cfd.1609828485.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Generate a change uevent when the "number_of_alternate_modes" sysfs file
for partners and plugs is updated by a port driver.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20210107034904.4112029-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The name of the module for the NVIDIA alt-mode is incorrect as it
looks to be a copy-paste error from the entry above, update it to
the correct typec_nvidia module name.
Cc: Ajay Gupta <ajayg@nvidia.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210106001605.167917-1-pbrobinson@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enable Super speed plus in configfs to support USB3.1 Gen2.
This ensures that when a USB gadget is plugged in, it is
enumerated as Gen 2 and connected at 10 Gbps if the host and
cable are capable of it.
Many in-tree gadget functions (fs, midi, acm, ncm, mass_storage,
etc.) already have SuperSpeed Plus support.
Tested: plugged gadget into Linux host and saw:
[284907.385986] usb 8-2: new SuperSpeedPlus Gen 2 USB device number 3 using xhci_hcd
Tested-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: taehyun.cho <taehyun.cho@samsung.com>
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Link: https://lore.kernel.org/r/20210106154625.2801030-1-lorenzo@google.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Done opencode in_serving_softirq() checks in in_serving_softirq() to avoid
cluttering the code, hide them in kcov helpers instead.
Fixes: aee9ddb1d371 ("kcov, usb: only collect coverage from __usb_hcd_giveback_urb in softirq")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lore.kernel.org/r/aeb430c5bb90b0ccdf1ec302c70831c1a47b9c45.1609876340.git.andreyknvl@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is observed 'use-after-free' on the dmabuf's file->f_inode with the
race between closing the dmabuf file and reading the dmabuf's debug
info.
Consider the below scenario where P1 is closing the dma_buf file
and P2 is reading the dma_buf's debug info in the system:
P1 P2
dma_buf_debug_show()
dma_buf_put()
__fput()
file->f_op->release()
dput()
....
dentry_unlink_inode()
iput(dentry->d_inode)
(where the inode is freed)
mutex_lock(&db_list.lock)
read 'dma_buf->file->f_inode'
(the same inode is freed by P1)
mutex_unlock(&db_list.lock)
dentry->d_op->d_release()-->
dma_buf_release()
.....
mutex_lock(&db_list.lock)
removes the dmabuf from the list
mutex_unlock(&db_list.lock)
In the above scenario, when dma_buf_put() is called on a dma_buf, it
first frees the dma_buf's file->f_inode(=dentry->d_inode) and then
removes this dma_buf from the system db_list. In between P2 traversing
the db_list tries to access this dma_buf's file->f_inode that was freed
by P1 which is a use-after-free case.
Since, __fput() calls f_op->release first and then later calls the
d_op->d_release, move the dma_buf's db_list removal from d_release() to
f_op->release(). This ensures that dma_buf's file->f_inode is not
accessed after it is released.
Cc: <stable@vger.kernel.org> # 5.4.x-
Fixes: 4ab59c3c638c ("dma-buf: Move dma_buf_release() from fops to dentry_ops")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Charan Teja Reddy <charante@codeaurora.org>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1609857399-31549-1-git-send-email-charante@codeaurora.org
|
|
The tb_dbg() call is using %#x that already adds the 0x prefix so don't
duplicate it.
Fixes: 9039387e166e ("thunderbolt: Add USB4 router operation proxy for firmware connection manager")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
|
|
The rcar_can driver also supports RZ/G SoC's, update the description to reflect
this.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210104090327.6547-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
pointer in HW, then in driver
The previous patch fixes a TEF vs. TX race condition, by first updating the TEF
tail pointer in hardware, and then updating the driver internal pointer.
The same pattern exists in the RX-path, too. This should be no problem, as the
driver accesses the RX-FIFO from the interrupt handler only, thus the access is
properly serialized. Fix the order here, too, so that the TEF- and RX-path look
similar.
Fixes: 1f652bb6bae7 ("can: mcp25xxfd: rx-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The mcp251xfd driver uses a TX FIFO for sending CAN frames and a TX Event FIFO
(TEF) for completed TX-requests.
The TEF event handling in the mcp251xfd_handle_tefif() function has a race
condition. It first increments the tx-ring's tail counter to signal that
there's room in the TX and TEF FIFO, then it increments the TEF FIFO in
hardware.
A running mcp251xfd_start_xmit() on a different CPU might not stop the txqueue
(as the tx-ring still shows free space). The next mcp251xfd_start_xmit() will
push a message into the chip and the TX complete event might overflow the TEF
FIFO.
This patch changes the order to fix the problem.
Fixes: 68c0c1c7f966 ("can: mcp251xfd: tef-path: reduce number of SPI core requests to set UINC bit")
Link: https://lore.kernel.org/r/20210105214138.3150886-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
drm/i915 fixes for v5.11-rc3:
- Use per-connector PM QoS tracking for DP aux communication
- GuC firmware fix for older Cometlakes
- Clear the gpu reloc and shadow batches
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/877dop18zf.fsf@intel.com
|
|
See Documentation/core-api/printk-formats.rst.
h should no longer be used in the format specifier for printk.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
See Documentation/core-api/printk-formats.rst.
h should no longer be used in the format specifier for printk.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.11-2021-01-06:
amdgpu:
- Telemetry fix for VGH
- Powerplay fixes for RV
- Powerplay fixes for RN
- RAS fixes for Sienna Cichlid
- Blank screen regression fix
- Drop DCN support for aarch64
- Misc other fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210106222721.3934-1-alexander.deucher@amd.com
|
|
According to the TCAN4550 datasheet "SLLSF91 - DECEMBER 2018" the tcan4x5x has
the same bittiming constants as a m_can revision 3.2.x/3.3.0.
The tcan4x5x chip I'm using identifies itself as m_can revision 3.2.1, so
remove the tcan4x5x specific bittiming values and rely on the values in the
m_can driver, which are selected according to core revision.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In m_can_class_register() the clock is started, but stopped on exit. When
calling m_can_class_unregister(), the clock is stopped a second time.
This patch removes the erroneous m_can_clk_stop() in m_can_class_unregister().
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Restore alignment of the continuation of the devm_ioremap() call in
register_intc_controller().
Fixes: 4bdc0d676a643140 ("remove ioremap_nocache and devm_ioremap_nocache")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rich Felker <dalias@libc.org>
|
