| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A series of fixes for the da9121 driver"
* tag 'regulator-fix-v5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: da9121: Remove surplus DA9141 parameters
regulator: da9121: Fix DA914x voltage value
regulator: da9121: Fix DA914x current values
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"A fix for interrupt controllers which require the explicit
acknowledgement of interrupts using a different register to the one
where interrupts are reported.
Urgent for the few devices this affects"
* tag 'regmap-fix-v5.17-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap-irq: Update interrupt clear register for proper reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix a memory leak in the int340x thermal driver's ACPI notify handler
(Chuansheng Liu)"
* tag 'thermal-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: fix memory leak in int3400_notify()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Fix the throttle IRQ handling during cpufreq initialization on
Qualcomm platforms (Bjorn Andersson)"
* tag 'pm-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: qcom-hw: Delay enabling throttle_irq
cpufreq: Reintroduce ready() callback
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a few small driver fixes for 5.17-rc6 for reported issues.
The majority of these are IIO fixes for small things, and the other
two are a mvmem and mtd core conflict fix.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
mtd: core: Fix a conflict between MTD and NVMEM on wp-gpios property
nvmem: core: Fix a conflict between MTD and NVMEM on wp-gpios property
iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
iio: Fix error handling for PM
iio: addac: ad74413r: correct comparator gpio getters mask usage
iio: addac: ad74413r: use ngpio size when iterating over mask
iio: addac: ad74413r: Do not reference negative array offsets
iio: adc: men_z188_adc: Fix a resource leak in an error handling path
iio: frequency: admv1013: remove the always true condition
iio: accel: fxls8962af: add padding to regmap for SPI
iio:imu:adis16480: fix buffering for devices with no burst mode
iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
iio: adc: tsc2046: fix memory corruption by preventing array overflow
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fix from Greg KH:
"Here is a single driver core fix for 5.17-rc6. It resolves a reported
problem when the DMA map of a device is not properly released.
It has been in linux-next with no reported problems"
* tag 'driver-core-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: Free DMA range map when device is released
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fix from Greg KH:
"Here is a single staging driver fix for 5.17-rc6.
It resolves a reported problem in the fbtft fb_st7789v.c driver that
could cause the display to be flipped in cold weather.
It has been in linux-next with no reported problems"
* tag 'staging-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: fbtft: fb_st7789v: reset display before initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small n_gsm and sc16is7xx serial driver fixes for
5.17-rc6.
The n_gsm fixes are from Siemens as it seems they are using the line
discipline and fixing up a number of issues they found in their
testing. The sc16is7xx serial driver fix is for a reported problem
with that chip.
All of these have been in linux-next with no reported problems"
* tag 'tty-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
sc16is7xx: Fix for incorrect data being transmitted
tty: n_gsm: fix deadlock in gsmtty_open()
tty: n_gsm: fix wrong modem processing in convergence layer type 2
tty: n_gsm: fix wrong tty control line for flow control
tty: n_gsm: fix NULL pointer access due to DLCI release
tty: n_gsm: fix proper link termination after failed open
tty: n_gsm: fix encoding of command/response bit
tty: n_gsm: fix encoding of control signal octet bit DV
|
|
The setup of __IAVF_RESETTING state in watchdog task had no
effect and could lead to slow resets in the driver as
the task for __IAVF_RESETTING state only requeues watchdog.
Till now the __IAVF_RESETTING was interpreted by reset task
as running state which could lead to errors with allocating
and resources disposal.
Make watchdog_task queue the reset task when it's necessary.
Do not update the state to __IAVF_RESETTING so the reset task
knows exactly what is the current state of the adapter.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver was queueing reset_task regardless of the netdev
state.
Do not queue the reset task in iavf_change_mtu if netdev
is not running.
Fixes: fdd4044ffdc8 ("iavf: Remove timer for work triggering, use delaying work instead")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There exists a missing mutex_unlock call on crit_lock in
iavf_reset_task call path.
Unlock the crit_lock before returning from reset task.
Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When iavf_init_version_check sends VIRTCHNL_OP_GET_VF_RESOURCES
message, the driver will wait for the response after requeueing
the watchdog task in iavf_init_get_resources call stack. The
logic is implemented this way that iavf_init_get_resources has
to be called in order to allocate adapter->vf_res. It is polling
for the AQ response in iavf_get_vf_config function. Expect a
call trace from kernel when adminq_task worker handles this
message first. adapter->vf_res will be NULL in
iavf_virtchnl_completion.
Make the watchdog task not queue the adminq_task if the init
process is not finished yet.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
iavf_virtchnl_completion is called under crit_lock but when
the code for VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS is called,
this lock is released in order to obtain rtnl_lock to avoid
ABBA deadlock with unregister_netdev.
Along with the new way iavf_remove behaves, there exist
many risks related to the lock release and attmepts to regrab
it. The driver faces crashes related to races between
unregister_netdev and netdev_update_features. Yet another
risk is that the driver could already obtain the crit_lock
in order to destroy it and iavf_virtchnl_completion could
crash or block forever.
Make iavf_virtchnl_completion never relock crit_lock in it's
call paths.
Extract rtnl_lock locking logic to the driver for
unregister_netdev in order to set the netdev_registered flag
inside the lock.
Introduce a new flag that will inform adminq_task to perform
the code from VIRTCHNL_OP_GET_OFFLOAD_VLAN_V2_CAPS right after
it finishes processing messages. Guard this code with remove
flags so it's never called when the driver is in remove state.
Fixes: 5951a2b9812d ("iavf: Fix VLAN feature flags after VFR")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When init states of the adapter work, the errors like lack
of communication with the PF might hop in. If such events
occur the driver restores previous states in order to retry
initialization in a proper way. When remove task kicks in,
this situation could lead to races with unregistering the
netdevice as well as resources cleanup. With the commit
introducing the waiting in remove for init to complete,
this problem turns into an endless waiting if init never
recovers from errors.
Introduce __IAVF_IN_REMOVE_TASK bit to indicate that the
remove thread has started.
Make __IAVF_COMM_FAILED adapter state respect the
__IAVF_IN_REMOVE_TASK bit and set the __IAVF_INIT_FAILED
state and return without any action instead of trying to
recover.
Make __IAVF_INIT_FAILED adapter state respect the
__IAVF_IN_REMOVE_TASK bit and return without any further
actions.
Make the loop in the remove handler break when adapter has
__IAVF_INIT_FAILED state set.
Fixes: 898ef1cb1cb2 ("iavf: Combine init and watchdog state machines")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There exist races when port is being configured and remove is
triggered.
unregister_netdev is not and can't be called under crit_lock
mutex since it is calling ndo_stop -> iavf_close which requires
this lock. Depending on init state the netdev could be still
unregistered so unregister_netdev never cleans up, when shortly
after that the device could become registered.
Make iavf_remove wait until port finishes initialization.
All critical state changes are atomic (under crit_lock).
Crashes that come from iavf_reset_interrupt_capability and
iavf_free_traffic_irqs should now be solved in a graceful
manner.
Fixes: 605ca7c5c6707 ("iavf: Fix kernel BUG in free_msi_irqs")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver used to crash in multiple spots when put to stress testing
of the init, reset and remove paths.
The user would experience call traces or hangs when creating,
resetting, removing VFs. Depending on the machines, the call traces
are happening in random spots, like reset restoring resources racing
with driver remove.
Make adapter->crit_lock mutex a mandatory lock for guarding the
operations performed on all workqueues and functions dealing with
resource allocation and disposal.
Make __IAVF_REMOVE a final state of the driver respected by
workqueues that shall not requeue, when they fail to obtain the
crit_lock.
Make the IRQ handler not to queue the new work for adminq_task
when the __IAVF_REMOVE state is set.
Fixes: 5ac49f3c2702 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Phani Burra <phani.r.burra@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.17-rc6 to resolve
reported problems and add new device ids. They include:
- dwc3:
- device mapping fix
- new device ids
- driver fixes
- xhci driver fixes
- gadget driver fixes
- usb-serial driver device id updates
All of these have been in linux-next with no reported problems"
* tag 'usb-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: gadget: rndis: add spinlock for rndis response list
usb: dwc3: gadget: Let the interrupt handler disable bottom halves.
USB: gadget: validate endpoint index for xilinx udc
USB: serial: option: add Telit LE910R1 compositions
USB: serial: option: add support for DW5829e
Revert "USB: serial: ch341: add new Product ID for CH341A"
usb: dwc2: drd: fix soft connect when gadget is unconfigured
usb: dwc3: pci: Fix Bay Trail phy GPIO mappings
tps6598x: clear int mask on probe failure
xhci: Prevent futile URB re-submissions due to incorrect return value.
xhci: re-initialize the HC during resume if HCE was set
usb: dwc3: pci: Add "snps,dis_u2_susphy_quirk" for Intel Bay Trail
usb: dwc3: pci: add support for the Intel Raptor Lake-S
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
"Two fixes for the pata_hpt37x driver, both from Sergey:
- Fix a PCI register access using an incorrect size (8bits instead of
16bits)
- Make sure to always disable the primary channel as it is unused"
* tag 'ata-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_hpt37x: disable primary channel on HPT371
ata: pata_hpt37x: fix PCI clock detection
|
|
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 causes the "option=value" string to be
added to init's environment strings, polluting it.
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Fixes: f3240e2811f0 ("stmmac: remove warning when compile as built-in (V2)")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Link: https://lore.kernel.org/r/20220224033536.25056-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 causes the "option=value" string to be
added to init's environment strings, polluting it.
Fixes: acc18c147b22 ("net: sxgbe: add EEE(Energy Efficient Ethernet) for Samsung sxgbe")
Fixes: 1edb9ca69e8a ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Siva Reddy <siva.kallam@samsung.com>
Cc: Girish K S <ks.giri@samsung.com>
Cc: Byungho An <bh74.an@samsung.com>
Link: https://lore.kernel.org/r/20220224033528.24640-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
fully ready
Register the CAN device only when all the necessary initialization is
completed. This patch makes sure all the data structures and locks are
initialized before registering the CAN device.
Link: https://lore.kernel.org/all/20220221225935.12300-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/fixes
NXP/FSL SoC driver fixes for v5.17
- Add missing SoC compatible in existing binding
- Replace kernel.h with the necessary inclusions
- MAINTAINERS file fixes
- Fix memory allocation failure check in guts driver
- Various cleanups and minor fixes
* tag 'soc-fsl-fix-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: Check of ioremap return value
soc: fsl: qe: fix typo in a comment
soc: fsl: guts: Add a missing memory allocation failure check
soc: fsl: guts: Revert commit 3c0d64e867ed
soc: fsl: Correct MAINTAINERS database (SOC)
soc: fsl: Correct MAINTAINERS database (QUICC ENGINE LIBRARY)
soc: fsl: Replace kernel.h with the necessary inclusions
dt-bindings: fsl,layerscape-dcfg: add missing compatible for lx2160a
dt-bindings: qoriq-clock: add missing compatible for lx2160a
Link: https://lore.kernel.org/r/20220219012208.21835-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Check if operation is valid before changing any
settings in hardware. Otherwise it results in
changes being made despite it not being a valid
operation.
Fixes: 78eab33bb68b ("net: sparx5: add vlan support")
Signed-off-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function pci_find_capability() in t3_prep_adapter() can fail, so its
return value should be checked.
Fixes: 4d22de3e6cc4 ("Add support for the latest 1G/10G Chelsio adapter, T3")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently don't allow queuing resets when adapter is in VNIC_PROBING
state - instead we throw away the reset and return EBUSY. The reasoning
is probably that during ibmvnic_probe() the ibmvnic_adapter itself is
being initialized so performing a reset during this time can lead us to
accessing fields in the ibmvnic_adapter that are not fully initialized.
A review of the code shows that all the adapter state neede to process a
reset is initialized before registering the CRQ so that should no longer
be a concern.
Further the expectation is that if we do get a reset (transport event)
during probe, the do..while() loop in ibmvnic_probe() will handle this
by reinitializing the CRQ.
While that is true to some extent, it is possible that the reset might
occur _after_ the CRQ is registered and CRQ_INIT message was exchanged
but _before_ the adapter state is set to VNIC_PROBED. As mentioned above,
such a reset will be thrown away. While the client assumes that the
adapter is functional, the vnic server will wait for the client to reinit
the adapter. This disconnect between the two leaves the adapter down
needing manual intervention.
Because ibmvnic_probe() has other work to do after initializing the CRQ
(such as registering the netdev at a minimum) and because the reset event
can occur at any instant after the CRQ is initialized, there will always
be a window between initializing the CRQ and considering the adapter
ready for resets (ie state == PROBED).
So rather than discarding resets during this window, allow queueing them
- but only process them after the adapter is fully initialized.
To do this, introduce a new completion state ->probe_done and have the
reset worker thread wait on this before processing resets.
This change brings up two new situations in or just after ibmvnic_probe().
First after one or more resets were queued, we encounter an error and
decide to retry the initialization. At that point the queued resets are
no longer relevant since we could be talking to a new vnic server. So we
must purge/flush the queued resets before restarting the initialization.
As a side note, since we are still in the probing stage and we have not
registered the netdev, it will not be CHANGE_PARAM reset.
Second this change opens up a potential race between the worker thread
in __ibmvnic_reset(), the tasklet and the ibmvnic_open() due to the
following sequence of events:
1. Register CRQ
2. Get transport event before CRQ_INIT completes.
3. Tasklet schedules reset:
a) add rwi to list
b) schedule_work() to start worker thread which runs
and waits for ->probe_done.
4. ibmvnic_probe() decides to retry, purges rwi_list
5. Re-register crq and this time rest of probe succeeds - register
netdev and complete(->probe_done).
6. Worker thread resumes in __ibmvnic_reset() from 3b.
7. Worker thread sets ->resetting bit
8. ibmvnic_open() comes in, notices ->resetting bit, sets state
to IBMVNIC_OPEN and returns early expecting worker thread to
finish the open.
9. Worker thread finds rwi_list empty and returns without
opening the interface.
If this happens, the ->ndo_open() call is effectively lost and the
interface remains down. To address this, ensure that ->rwi_list is
not empty before setting the ->resetting bit. See also comments in
__ibmvnic_reset().
Fixes: 6a2fb0e99f9c ("ibmvnic: driver initialization for kdump/kexec")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clear ->failover_pending flag that may have been set in the previous
pass of registering CRQ. If we don't clear, a subsequent ibmvnic_open()
call would be misled into thinking a failover is pending and assuming
that the reset worker thread would open the adapter. If this pass of
registering the CRQ succeeds (i.e there is no transport event), there
wouldn't be a reset worker thread.
This would leave the adapter unconfigured and require manual intervention
to bring it up during boot.
Fixes: 5a18e1e0c193 ("ibmvnic: Fix failover case for non-redundant configuration")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently initialize the ->init_done completion/return code fields
before issuing a CRQ_INIT command. But if we get a transport event soon
after registering the CRQ the taskslet may already have recorded the
completion and error code. If we initialize here, we might overwrite/
lose that and end up issuing the CRQ_INIT only to timeout later.
If that timeout happens during probe, we will leave the adapter in the
DOWN state rather than retrying to register/init the CRQ.
Initialize the completion before registering the CRQ so we don't lose
the notification.
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Finish initializing the adapter before registering netdev so state
is consistent.
Fixes: c26eba03e407 ("ibmvnic: Update reset infrastructure to support tunable parameters")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we get a transport event, set the error and mark the init as
complete so the attempt to send crq-init or login fail sooner
rather than wait for the timeout.
Fixes: bbd669a868bb ("ibmvnic: Fix completion structure initialization")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Define and use a helper to flush the reset queue.
Fixes: 2770a7984db5 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should initialize ->init_done_rc before calling complete(). Otherwise
the waiting thread may see ->init_done_rc as 0 before we have updated it
and may assume that the CRQ was successful.
Fixes: 6b278c0cb378 ("ibmvnic delay complete()")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a tiny memory leak when flushing the reset work queue.
Fixes: 2770a7984db5 ("ibmvnic: Introduce hard reset recovery")
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this driver's ->ndo_open() callback, it enables DMA interrupts,
starts the DMA channels, then requests interrupts with request_irq(),
and then finally enables napi.
If RX DMA interrupts are received before napi is enabled, no processing
is done because napi_schedule_prep() will return false. If the network
has a lot of broadcast/multicast traffic, then the RX ring could fill up
completely before napi is enabled. When this happens, no further RX
interrupts will be delivered, and the driver will fail to receive any
packets.
Fix this by only enabling DMA interrupts after all other initialization
is complete.
Fixes: 523f11b5d4fd72efb ("net: stmmac: move hardware setup for stmmac_open to new function")
Reported-by: Lars Persson <larper@axis.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xennet_destroy_queues() relies on info->netdev->real_num_tx_queues to
delete queues. Since d7dac083414eb5bb99a6d2ed53dc2c1b405224e5
("net-sysfs: update the queue counts in the unregistration path"),
unregister_netdev() indirectly sets real_num_tx_queues to 0. Those two
facts together means, that xennet_destroy_queues() called from
xennet_remove() cannot do its job, because it's called after
unregister_netdev(). This results in kfree-ing queues that are still
linked in napi, which ultimately crashes:
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 52 Comm: xenwatch Tainted: G W 5.16.10-1.32.fc32.qubes.x86_64+ #226
RIP: 0010:free_netdev+0xa3/0x1a0
Code: ff 48 89 df e8 2e e9 00 00 48 8b 43 50 48 8b 08 48 8d b8 a0 fe ff ff 48 8d a9 a0 fe ff ff 49 39 c4 75 26 eb 47 e8 ed c1 66 ff <48> 8b 85 60 01 00 00 48 8d 95 60 01 00 00 48 89 ef 48 2d 60 01 00
RSP: 0000:ffffc90000bcfd00 EFLAGS: 00010286
RAX: 0000000000000000 RBX: ffff88800edad000 RCX: 0000000000000000
RDX: 0000000000000001 RSI: ffffc90000bcfc30 RDI: 00000000ffffffff
RBP: fffffffffffffea0 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000001 R12: ffff88800edad050
R13: ffff8880065f8f88 R14: 0000000000000000 R15: ffff8880066c6680
FS: 0000000000000000(0000) GS:ffff8880f3300000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000000 CR3: 00000000e998c006 CR4: 00000000003706e0
Call Trace:
<TASK>
xennet_remove+0x13d/0x300 [xen_netfront]
xenbus_dev_remove+0x6d/0xf0
__device_release_driver+0x17a/0x240
device_release_driver+0x24/0x30
bus_remove_device+0xd8/0x140
device_del+0x18b/0x410
? _raw_spin_unlock+0x16/0x30
? klist_iter_exit+0x14/0x20
? xenbus_dev_request_and_reply+0x80/0x80
device_unregister+0x13/0x60
xenbus_dev_changed+0x18e/0x1f0
xenwatch_thread+0xc0/0x1a0
? do_wait_intr_irq+0xa0/0xa0
kthread+0x16b/0x190
? set_kthread_struct+0x40/0x40
ret_from_fork+0x22/0x30
</TASK>
Fix this by calling xennet_destroy_queues() from xennet_uninit(),
when real_num_tx_queues is still available. This ensures that queues are
destroyed when real_num_tx_queues is set to 0, regardless of how
unregister_netdev() was called.
Originally reported at
https://github.com/QubesOS/qubes-issues/issues/7257
Fixes: d7dac083414eb5bb9 ("net-sysfs: update the queue counts in the unregistration path")
Cc: stable@vger.kernel.org
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes
Fixes for omaps
Fixes for devkit8000 timer regression. Similar to the earlier beagleboard
fixes, we must not configure the clocksource drivers to use an alternative
timer configuration. It causes unnecessary issues with power management.
Only some old designs based on early beagleboard revisions with a miswired
timer need to use the alternative timer.
* tag 'omap-for-v5.17/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Use 32KiHz oscillator on devkit8000
ARM: dts: switch timer config to common devkit8000 devicetree
Link: https://lore.kernel.org/r/pull-1645606483-876944@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The driver uses an atomic_t variable: gs_usb:active_channels to keep
track of the number of opened channels in order to only allocate
memory for the URBs when this count changes from zero to one.
However, the driver does not decrement the counter when an error
occurs in gs_can_open(). This issue is fixed by changing the type from
atomic_t to u8 and by simplifying the logic accordingly.
It is safe to use an u8 here because the network stack big kernel lock
(a.k.a. rtnl_mutex) is being hold. For details, please refer to [1].
[1] https://lore.kernel.org/linux-can/CAMZ6Rq+sHpiw34ijPsmp7vbUpDtJwvVtdV7CvRZJsLixjAFfrg@mail.gmail.com/T/#t
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/all/20220214234814.1321599-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver uses an atomic_t variable: struct
es58x_device::opened_channel_cnt to keep track of the number of opened
channels in order to only allocate memory for the URBs when this count
changes from zero to one.
While the intent was to prevent race conditions, the choice of an
atomic_t turns out to be a bad idea for several reasons:
- implementation is incorrect and fails to decrement
opened_channel_cnt when the URB allocation fails as reported in
[1].
- even if opened_channel_cnt were to be correctly decremented,
atomic_t is insufficient to cover edge cases: there can be a race
condition in which 1/ a first process fails to allocate URBs
memory 2/ a second process enters es58x_open() before the first
process does its cleanup and decrements opened_channed_cnt. In
which case, the second process would successfully return despite
the URBs memory not being allocated.
- actually, any kind of locking mechanism was useless here because
it is redundant with the network stack big kernel lock
(a.k.a. rtnl_lock) which is being hold by all the callers of
net_device_ops:ndo_open() and net_device_ops:ndo_close(). c.f. the
ASSERST_RTNL() calls in __dev_open() [2] and __dev_close_many()
[3].
The atmomic_t is thus replaced by a simple u8 type and the logic to
increment and decrement es58x_device:opened_channel_cnt is simplified
accordingly fixing the bug reported in [1]. We do not check again for
ASSERST_RTNL() as this is already done by the callers.
[1] https://lore.kernel.org/linux-can/20220201140351.GA2548@kili/T/#u
[2] https://elixir.bootlin.com/linux/v5.16/source/net/core/dev.c#L1463
[3] https://elixir.bootlin.com/linux/v5.16/source/net/core/dev.c#L1541
Fixes: 8537257874e9 ("can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces")
Link: https://lore.kernel.org/all/20220212112713.577957-1-mailhol.vincent@wanadoo.fr
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A couple driver fixes in the clk subsystem
- Fix a hang due to bad clk parent in the Ingenic jz4725b driver
- Fix SD controllers on Qualcomm MSM8994 SoCs by removing clks that
shouldn't be touched"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: jz4725b: fix mmc0 clock gating
clk: qcom: gcc-msm8994: Remove NoC clocks
|
|
Pull drm fixes from Dave Airlie:
"Regular drm fixes pull, i915, amdgpu and tegra mostly, all pretty
small.
core:
- edid: Always set RGB444
tegra:
- tegra186 suspend/resume fixes
- syncpoint wait fix
- build warning fix
- eDP on older devices fix
amdgpu:
- Display FP fix
- PCO powergating fix
- RDNA2 OEM SKU stability fixes
- Display PSR fix
- PCI ASPM fix
- Display link encoder fix for TEST_COMMIT
- Raven2 suspend/resume fix
- Fix a regression in virtual display support
- GPUVM eviction fix
i915:
- Fix QGV handling on ADL-P+
- Fix bw atomic check when switching between SAGV vs. no SAGV
- Disconnect PHYs left connected by BIOS on disabled ports
- Fix SAVG to no SAGV transitions on TGL+
- Print PHY name properly on calibration error (DG2)
imx:
- dcss: Select GEM CMA helpers
radeon:
- Fix some variables's type
vc4:
- Fix codec cleanup
- Fix PM reference counting"
* tag 'drm-fixes-2022-02-25' of git://anongit.freedesktop.org/drm/drm: (24 commits)
drm/amdgpu: check vm ready by amdgpu_vm->evicting flag
drm/amdgpu: bypass tiling flag check in virtual display case (v2)
Revert "drm/amdgpu: add modifiers in amdgpu_vkms_plane_init()"
drm/amdgpu: do not enable asic reset for raven2
drm/amd/display: Fix stream->link_enc unassigned during stream removal
drm/amd: Check if ASPM is enabled from PCIe subsystem
drm/edid: Always set RGB444
drm/tegra: dpaux: Populate AUX bus
drm/radeon: fix variable type
drm/amd/display: For vblank_disable_immediate, check PSR is really used
drm/amd/pm: fix some OEM SKU specific stability issues
drm/amdgpu: disable MMHUB PG for Picasso
drm/amd/display: Protect update_bw_bounding_box FPU code.
drm/i915/dg2: Print PHY name properly on calibration error
drm/i915: Fix bw atomic check when switching between SAGV vs. no SAGV
drm/i915: Correctly populate use_sagv_wm for all pipes
drm/i915: Disconnect PHYs left connected by BIOS on disabled ports
drm/i915: Widen the QGV point mask
drm/imx/dcss: i.MX8MQ DCSS select DRM_GEM_CMA_HELPER
drm/vc4: crtc: Fix runtime_pm reference counting
...
|
|
If the config options HAS_IOMEM is not set then the driver fails to link
with the following error:
clk-lan966x.c:(.text+0x950): undefined reference to
`devm_platform_ioremap_resource'
Therefor add missing dependencies: HAS_IOMEM and OF.
Fixes: 54104ee02333 ("clk: lan966x: Add lan966x SoC clock driver")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220219141536.460812-1-horatiu.vultur@microchip.com
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
TE-gpio, if defined, is placed in the panel's node, not the parent DSI
node. Change the devm_gpiod_get_optional() to gpiod_get_optional() and
pass proper device node to it. The code already has a proper cleanup
path, so it looks that the devm_* variant has been applied accidentally
during the conversion to gpiod API.
Fixes: ee6c8b5afa62 ("drm/exynos: Replace legacy gpio interface for gpiod interface")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixed a typo.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
TE-gpio is optional and if it is not found then gpiod_get_optional()
returns NULL. In such case the code will continue and try to convert NULL
gpiod to irq what in turn fails. The failure is then propagated and driver
is not registered.
Fix this by returning early from exynos_dsi_register_te_irq() if no
TE-gpio is found.
Fixes: ee6c8b5afa62 ("drm/exynos: Replace legacy gpio interface for gpiod interface")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
platform_get_resource_byname(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypassed the hierarchical setup and messed up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_byname().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
On SC7180 we observe black screens because the gdsc is being
enabled/disabled very rapidly and the GDSC FSM state does not work as
expected. This is due to the fact that the GDSC reset value is being
updated from SW.
The recommended transition delay for mdss core gdsc updated for
SC7180/SC7280/SM8250.
Fixes: dd3d06622138 ("clk: qcom: Add display clock controller driver for SC7180")
Fixes: 1a00c962f9cd ("clk: qcom: Add display clock controller driver for SC7280")
Fixes: 80a18f4a8567 ("clk: qcom: Add display clock controller driver for SM8150 and SM8250")
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/20220223185606.3941-2-tdas@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[sboyd@kernel.org: lowercase hex]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
GDSCs have multiple transition delays which are used for the GDSC FSM
states. Older targets/designs required these values to be updated from
gdsc code to certain default values for the FSM state to work as
expected. But on the newer targets/designs the values updated from the
GDSC driver can hamper the FSM state to not work as expected.
On SC7180 we observe black screens because the gdsc is being
enabled/disabled very rapidly and the GDSC FSM state does not work as
expected. This is due to the fact that the GDSC reset value is being
updated from SW.
Thus add support to update the transition delay from the clock
controller gdscs as required.
Fixes: 45dd0e55317cc ("clk: qcom: Add support for GDSCs)
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lore.kernel.org/r/20220223185606.3941-1-tdas@codeaurora.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.17, round 2:
- Drop reset signal from i.MX8MM vpumix power domain to fix a system
hang.
- Fix a dtbs_check warning caused by #thermal-sensor-cells in i.MX8ULP
device tree.
- Fix a clock disabling imbalance in gpcv2 driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
