| Age | Commit message (Collapse) | Author |
|---|
|
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based kernel configuration guards.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
spi: Support DTR in spi-mem
Changes to support DTR with spi-mem.
|
|
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Some PCI host bridges require special handling when enabling or
disabling PCI devices. For example, the i.MX95 platform has a lookup
table to map Requester IDs to StreamIDs, which the SMMU and MSI
controller use to identify the source of DMA accesses.
Without this mapping, DMA accesses may target unintended memory, which
would corrupt memory or read the wrong data.
Add a host bridge enable_device() hook the imx6 driver can use to
configure the Requester ID to StreamID mapping. The hardware table isn't
big enough to map all possible Requester IDs, so this hook may fail if
no table space is available. In that case, return failure from
pci_enable_device().
It might make more sense to make pci_set_master() decline to enable bus
mastering and return failure, but it currently doesn't have a way to return
failure.
Link: https://lore.kernel.org/r/20250114-imx95_lut-v9-1-39f58dbed03a@nxp.com
Tested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
[kwilczynski: commit log]
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Apparently the Raptor Lake-P reference firmware configures the PIO log size
correctly, but some vendor BIOSes, including at least ASUSTeK COMPUTER INC.
Zenbook UX3402VA_UX3402VA, do not.
Apply the quirk for Raptor Lake-P. This prevents kernel complaints like:
DPC: RP PIO log size 0 is invalid
and also enables the DPC driver to dump the RP PIO Log registers when DPC
is triggered.
Note that the bug report also mentions 8086:a76e, which has been already
added by 627c6db20703 ("PCI/DPC: Quirk PIO log size for Intel Raptor Lake
Root Ports").
Link: https://lore.kernel.org/r/20250102164315.7562-1-tiwai@suse.de
Link: https://bugzilla.suse.com/show_bug.cgi?id=1234623
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
|
|
This reverts commit 98d1fb94ce75f39febd456d6d3cbbe58b6678795.
The commit uses data nbits instead of addr nbits for dummy phase. This
causes a regression for all boards where spi-tx-bus-width is smaller
than spi-rx-bus-width. It is a common pattern for boards to have
spi-tx-bus-width == 1 and spi-rx-bus-width > 1. The regression causes
all reads with a dummy phase to become unavailable for such boards,
leading to a usually slower 0-dummy-cycle read being selected.
Most controllers' supports_op hooks call spi_mem_default_supports_op().
In spi_mem_default_supports_op(), spi_mem_check_buswidth() is called to
check if the buswidths for the op can actually be supported by the
board's wiring. This wiring information comes from (among other things)
the spi-{tx,rx}-bus-width DT properties. Based on these properties,
SPI_TX_* or SPI_RX_* flags are set by of_spi_parse_dt().
spi_mem_check_buswidth() then uses these flags to make the decision
whether an op can be supported by the board's wiring (in a way,
indirectly checking against spi-{rx,tx}-bus-width).
Now the tricky bit here is that spi_mem_check_buswidth() does:
if (op->dummy.nbytes &&
spi_check_buswidth_req(mem, op->dummy.buswidth, true))
return false;
The true argument to spi_check_buswidth_req() means the op is treated as
a TX op. For a board that has say 1-bit TX and 4-bit RX, a 4-bit dummy
TX is considered as unsupported, and the op gets rejected.
The commit being reverted uses the data buswidth for dummy buswidth. So
for reads, the RX buswidth gets used for the dummy phase, uncovering
this issue. In reality, a dummy phase is neither RX nor TX. As the name
suggests, these are just dummy cycles that send or receive no data, and
thus don't really need to have any buswidth at all.
Ideally, dummy phases should not be checked against the board's wiring
capabilities at all, and should only be sanity-checked for having a sane
buswidth value. Since we are now at rc7 and such a change might
introduce many unexpected bugs, revert the commit for now. It can be
sent out later along with the spi_mem_check_buswidth() fix.
Fixes: 98d1fb94ce75 ("mtd: spi-nor: core: replace dummy buswidth from addr to data")
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Closes: https://lore.kernel.org/linux-mtd/3342163.44csPzL39Z@steina-w/
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
TOSHIBA TransMemory-Mx is a good performence flash device, but it
doesn't work well with LPM on Huawei hisi platform, so let's disable
LPM to resolve the issue.
Signed-off-by: Miao Li <limiao@kylinos.cn>
Link: https://lore.kernel.org/r/20250113085619.44371-1-limiao870622@163.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
* pr_err() of request_region() in cb7210 uses 0x%u which is defective.
* The config->ibbase is of u32 and correct prefix is 0x%x.
* This error reported by checkpatch with below message:
ERROR: Prefixing 0x with decimal output is defective
Signed-off-by: Ajith P V <ajithpv.linux@gmail.com>
Link: https://lore.kernel.org/r/20250114121656.30577-1-ajithpv.linux@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some drivers were still using the old syntax for initializing
structs:
field : value;
This caused sparse to emit the following warning, for example:
common/gpib_os.c:2026:1: warning: obsolete struct initializer, use C99 syntax
Use C99 syntax:
.field = value;
Some local structs and arrays were not declared static causing
sparse to emit the following warning, for example:
warning: symbol 'ib_fops' was not declared. Should it be static?
Declare the local structs and arrays as static.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250114165403.16410-5-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A number of drivers were comparing request_region() with 0,
others were passing 0 instead of NULL as a pointer argument.
This led to the following sparse warning, for example:
cb7210/cb7210.c:1043:72: warning: Using plain integer as NULL pointer
Use !request_region() to test for NULL return and use NULL instead
of 0 as pointer parameter.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250114165403.16410-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The user buffers in copy_from_user, copy_to_user and some file ops
did not use the __user address space attribute.
This led to the following sparse warning, for example:
common/gpib_os.c:838:40: warning: incorrect type in argument 2 (different address spaces)
common/gpib_os.c:838:40: expected void const [noderef] __user *from
common/gpib_os.c:838:40: got void *
Add the __user address space attribute where needed.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250114165403.16410-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In a number of drivers the PCI memory pointers were declared simply as
void *.
This caused sparse to emit the following warning, for example:
agilent_82350b/agilent_82350b.c:44:58: warning: incorrect type in argument 2 (different address spaces)
agilent_82350b/agilent_82350b.c:44:58: expected void volatile [noderef] __iomem *addr
Declare the PCI memory pointers as void __iomem *addr.
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20250114165403.16410-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20250114-sysfs-const-bin_attr-devcoredump-v1-2-fa93be30efae@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The macro saves some lines of code and simplifies the constification of
the attribute.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20250114-sysfs-const-bin_attr-devcoredump-v1-1-fa93be30efae@weissschuh.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are too many different host behaviors when it comes to NoStream
handling, and not everyone follows the USB and xHCI spec. The DWC3
driver attempts to do some guess work to interop with different hosts,
but it can't cover everything. Let's keep it simple and treat every host
the same: just retry on NoStream after a 100ms of no response delay.
Note that some hosts cannot handle frequent retries. This may affect
performance on certain defective hosts, but NoStream is a rare
occurrence and interoperability is more important.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/b92ae94c86f01f165d5f178b7767898573b6dc75.1736819308.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-6-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-5-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-4-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-3-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-2-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use existing str_plural() helper from string_choices.h to reduce amount
of duplicated code.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250114-str-enable-disable-usb-v1-1-c8405df47c19@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
soc/drivers
Reset controller updates for v6.14 (v2)
* Add support for A1 SoC in amlogic reset driver.
* Drop aux registration helper from amlogic reset driver.
* tag 'reset-for-v6.14-2' of git://git.pengutronix.de/pza/linux:
reset: amlogic: aux: drop aux registration helper
reset: amlogic: aux: get regmap through parent device
reset: amlogic: add support for A1 SoC in auxiliary reset driver
dt-bindings: reset: add bindings for A1 SoC audio reset controller
clk: amlogic: axg-audio: revert reset implementation
Revert "clk: Fix invalid execution of clk_set_rate"
Link: https://lore.kernel.org/r/20250115170247.1303656-1-p.zabel@pengutronix.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() and getting the argument. Except
simpler code this annotates within one line that given phandle has
arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20250111-b4-syscon-phandle-args-remoteproc-v1-5-73ed6fafa1e3@linaro.org
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Use syscon_regmap_lookup_by_phandle_args() which is a wrapper over
syscon_regmap_lookup_by_phandle() and getting the argument. Except
simpler code this annotates within one line that given phandle has
arguments, so grepping for code would be easier.
There is also no real benefit in printing errors on missing syscon
argument, because this is done just too late: runtime check on
static/build-time data. Dtschema and Devicetree bindings offer the
static/build-time check for this already.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250111-b4-syscon-phandle-args-remoteproc-v1-4-73ed6fafa1e3@linaro.org
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
Having the aux registration helper along with the registered driver is not
great dependency wise. It does not allow the registering driver to be
properly decoupled from the registered auxiliary driver.
Drop the registration helper from the amlogic auxiliary reset driver.
This will be handled in the registering clock driver to start with while
a more generic solution is worked on.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241209-meson-rst-aux-rework-v1-2-d2afb69cc72e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Get regmap directly from the parent device registering the
auxiliary reset driver, instead of using device data attached
to the auxiliary device.
This simplifies the registration a bit.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20241209-meson-rst-aux-rework-v1-1-d2afb69cc72e@baylibre.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Add support for the reset controller present in the audio clock
controller of A1 SoC families, using the auxiliary bus.
Signed-off-by: Jan Dakinevich <jan.dakinevich@salutedevices.com>
Link: https://lore.kernel.org/r/20241112230056.1406222-3-jan.dakinevich@salutedevices.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Use dev_err_probe() to make error code handling simpler and handle
deferred probe.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20250111-b4-syscon-phandle-args-remoteproc-v1-3-73ed6fafa1e3@linaro.org
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath
ath.git patches for v6.14
This development cycle again featured multiple patchsets to ath12k to
support the new 802.11be MLO feature, this time including the device
grouping infrastructure, and the advertisement of MLO support to the
wireless core. However the MLO feature is still considered to be
incomplete.
In addition, there was the usual set of bug fixes and cleanups, mostly
in ath12k, but also in ath9k.
|
|
No need to store PTR_ERR into temporary, local 'ret' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250111-b4-syscon-phandle-args-remoteproc-v1-2-73ed6fafa1e3@linaro.org
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
No need to store PTR_ERR into temporary, local 'ret' variable.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250111-b4-syscon-phandle-args-remoteproc-v1-1-73ed6fafa1e3@linaro.org
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
|
|
wiphy_unregister()/wiphy_free() has been recently decoupled from
wilc_netdev_cleanup() to fix a faulty error path in sdio/spi probe
functions. However this change introduced a new failure when simply
loading then unloading the driver:
$ modprobe wilc1000-sdio; modprobe -r wilc1000-sdio
WARNING: CPU: 0 PID: 115 at net/wireless/core.c:1145 wiphy_unregister+0x904/0xc40 [cfg80211]
Modules linked in: wilc1000_sdio(-) wilc1000 cfg80211 bluetooth ecdh_generic ecc
CPU: 0 UID: 0 PID: 115 Comm: modprobe Not tainted 6.13.0-rc6+ #45
Hardware name: Atmel SAMA5
Call trace:
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x44/0x70
dump_stack_lvl from __warn+0x118/0x27c
__warn from warn_slowpath_fmt+0xcc/0x140
warn_slowpath_fmt from wiphy_unregister+0x904/0xc40 [cfg80211]
wiphy_unregister [cfg80211] from wilc_sdio_remove+0xb0/0x15c [wilc1000_sdio]
wilc_sdio_remove [wilc1000_sdio] from sdio_bus_remove+0x104/0x3f0
sdio_bus_remove from device_release_driver_internal+0x424/0x5dc
device_release_driver_internal from driver_detach+0x120/0x224
driver_detach from bus_remove_driver+0x17c/0x314
bus_remove_driver from sys_delete_module+0x310/0x46c
sys_delete_module from ret_fast_syscall+0x0/0x1c
Exception stack(0xd0acbfa8 to 0xd0acbff0)
bfa0: 0044b210 0044b210 0044b24c 00000800 00000000 00000000
bfc0: 0044b210 0044b210 00000000 00000081 00000000 0044b210 00000000 00000000
bfe0: 00448e24 b6af99c4 0043ea0d aea2e12c
irq event stamp: 0
hardirqs last enabled at (0): [<00000000>] 0x0
hardirqs last disabled at (0): [<c01588f0>] copy_process+0x1c4c/0x7bec
softirqs last enabled at (0): [<c0158944>] copy_process+0x1ca0/0x7bec
softirqs last disabled at (0): [<00000000>] 0x0
The warning is triggered by the fact that there is still a
wireless_device linked to the wiphy we are unregistering, due to
wiphy_unregister() now being called after net device unregister (performed
in wilc_netdev_cleanup()). Fix this warning by moving wiphy_unregister()
after wilc_netdev_cleanup() is nominal paths (ie: driver removal).
wilc_netdev_cleanup() ordering is left untouched in error paths in probe
function because net device is not registered in those paths (so the
warning can not trigger), yet the wiphy can still be registered, and we
still some cleanup steps from wilc_netdev_cleanup().
Fixes: 1be94490b6b8 ("wifi: wilc1000: unregister wiphy only if it has been registered")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20250114-wilc1000_modprobe-v1-1-ad19d46f0c07@bootlin.com
|
|
For WCN6855, board ID specific NVM needs to be downloaded once board ID
is available, but the default NVM is always downloaded currently.
The wrong NVM causes poor RF performance, and effects user experience
for several types of laptop with WCN6855 on the market.
Fix by downloading board ID specific NVM if board ID is available.
Fixes: 095327fede00 ("Bluetooth: hci_qca: Add support for QTI Bluetooth chip wcn6855")
Cc: stable@vger.kernel.org # 6.4
Signed-off-by: Zijun Hu <quic_zijuhu@quicinc.com>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Steev Klimaszewski <steev@kali.org> #Thinkpad X13s
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The hdev->reset is never used now and the hdev->cmd_timeout actually
does reset. This patch changes the call path from
hdev->cmd_timeout -> vendor_cmd_timeout -> btusb_reset -> hdev->reset
, to
hdev->reset -> vendor_reset -> btusb_reset
Which makes it clear when we export the hdev->reset to a wider usage
e.g. allowing reset from sysfs.
This patch doesn't introduce any behavior change.
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Remove the cmd timeout count in btusb since we only ever allow one
command in flight at a time. We should always reset after a single
command times out.
Signed-off-by: Hsin-chen Chuang <chharry@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Replace ternary (condition ? "enable" : "disable") syntax with helpers
from string_choices.h because:
1. Simple function call with one argument is easier to read. Ternary
operator has three arguments and with wrapping might lead to quite
long code.
2. Is slightly shorter thus also easier to read.
3. It brings uniformity in the text - same string.
4. Allows deduping by the linker, which results in a smaller binary
file.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Remove resetting mt7921 before downloading the fw, as it may cause
command timeout when performing the reset.
Signed-off-by: Hao Qin <hao.qin@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=07 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3600 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
S: SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Garrett Wilke <garrett@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3576 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Garrett Wilke <garrett@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
If insert an USB dongle which chip is not maintained in ic_id_table, it
will hit the NULL point accessed. Add a null point check to avoid the
Kernel Oops.
Fixes: b39910bb54d9 ("Bluetooth: Populate hci_set_hw_info for Intel and Realtek")
Reviewed-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
devm_kstrdup() can return a NULL pointer on failure,but this
returned value in btbcm_get_board_name() is not checked.
Add NULL check in btbcm_get_board_name(), to handle kernel NULL
pointer dereference error.
Fixes: f9183eaad915 ("Bluetooth: btbcm: Use devm_kstrdup()")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The firmware-name property has been expanded to specify the names of NVM
and rampatch firmware for certain chips, such as the QCA6698 Bluetooth
chip. Although it shares the same IP core as the WCN6855, the QCA6698
has different RF components and RAM sizes, necessitating new firmware
files. This change allows for the configuration of NVM and rampatch in
DT.
Possible configurations:
firmware-name = QCA6698/hpnv21.bin, QCA6698/hpbtfw21.tlv;
firmware-name = QCA6698/hpnv21, QCA6698/hpbtfw21.tlv;
Signed-off-by: Cheng Jiang <quic_chejiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Different connectivity boards may be attached to the same platform. For
example, QCA6698-based boards can support either a two-antenna or
three-antenna solution, both of which work on the sa8775p-ride platform.
Due to differences in connectivity boards and variations in RF
performance from different foundries, different NVM configurations are
used based on the board ID.
Therefore, in the firmware-name property, if the NVM file has an
extension, the NVM file will be used. Otherwise, the system will first
try the .bNN (board ID) file, and if that fails, it will fall back to
the .bin file.
Possible configurations:
firmware-name = "QCA6698/hpnv21";
firmware-name = "QCA6698/hpnv21.bin";
Signed-off-by: Cheng Jiang <quic_chejiang@quicinc.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Add VID 13d3 & PID 3628 for MediaTek MT7925 USB Bluetooth chip.
The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.
T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3628 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: En-Wei Wu <en-wei.wu@canonical.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
A new machine has a Archer AX3000 / TX55e in it,
and out the box reported issues resetting hci0. It looks like
this is a MT7922 from the lspci output, so treat it as a MediaTek
device and use the proper callbacks. With that in place an xbox
controller can be used without issue as seen below:
[ 7.047388] Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20241106163512
[ 9.583883] Bluetooth: hci0: Device setup in 2582842 usecs
[ 9.583895] Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported.
[ 9.644780] Bluetooth: hci0: AOSP extensions version v1.00
[ 9.644784] Bluetooth: hci0: AOSP quality report is supported
[ 876.379876] input: Xbox Wireless Controller as /devices/virtual/misc/uhid/0005:045E:0B13.0006/input/input27
[ 876.380215] hid-generic 0005:045E:0B13.0006: input,hidraw3: BLUETOOTH HID v5.15 Gamepad [Xbox Wireless Controller] on c0:bf:be:27:de:f7
[ 876.429368] input: Xbox Wireless Controller as /devices/virtual/misc/uhid/0005:045E:0B13.0006/input/input28
[ 876.429423] microsoft 0005:045E:0B13.0006: input,hidraw3: BLUETOOTH HID v5.15 Gamepad [Xbox Wireless Controller] on c0:bf:be:27:de:f7
lspci output:
root@livingroom:/home/ajhalaney/git# lspci
...
05:00.0 Network controller: MEDIATEK Corp. MT7922 802.11ax PCI Express Wireless Network Adapter
and USB device:
root@livingroom:/home/ajhalaney/git# cat /sys/kernel/debug/usb/devices
...
T: Bus=01 Lev=01 Prnt=01 Port=10 Cnt=03 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3610 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I:* If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Andrew Halaney <ajhalaney@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
When a Bluetooth raw socket is open, the HCI event related to SCO
connection changes are not dispatched to the hci_event module, and
the underlying Bluetooth controller's USB Interface 1 will not be
updated accordingly.
This patch adds `isoc_alt` sysfs attribute, allowing user space
to update the alternate setting of the USB interface alternate
setting as needed.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Adds a new entry with VID 0x2c7c and PID 0x0130 to the btusb quirks table as it uses a Qualcomm WCN785x chipset
The device information from /sys/kernel/debug/usb/devices is provided below:
T: Bus=01 Lev=01 Prnt=01 Port=04 Cnt=05 Dev#= 7 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0130 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms
Signed-off-by: Mark Dietzer <git@doridian.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
mt76 patches for 6.14
- mlo fixes for mt792x
- single wiphy multiband support for mt7996
- mt7915 stability fixes
|
|
rtw-next patches for v6.14
rtl8xxxu, rtlwifi and rtw88 fix field issues reported by users.
rtw89 is ongoing to implement MLO and fix issues during the development.
Major changes:
rtw88:
- support LED blinking
rtw89:
- support RTL8922AE-VS chip
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next
Pull Thunderbolt updates from Mika:
thunderbolt: Changes for v6.14 merge window
This includes following USB4/Thunderbolt changes for the v6.14 merge
window:
- Add debugfs write capability to path config spaces.
- Expose router DROM through debugfs.
- Increase DPRX capabilities read timeout to support runtime
suspending of graphics driver.
- Handle DisplayPort tunnel activation asynchronously.
- Small cleanups.
All these have been in linux-next with no reported issues.
* tag 'thunderbolt-for-v6.14-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
thunderbolt: Expose router DROM through debugfs
thunderbolt: Handle DisplayPort tunnel activation asynchronously
thunderbolt: Rework tb_tunnel_consumed_bandwidth()
thunderbolt: Move forward declarations in one place
thunderbolt: Pass reason to tb_dp_resource_unavailable()
thunderbolt: Drop tb_tunnel_restart()
thunderbolt: Rework how tunnel->[init|deinit] hooks are called
thunderbolt: Show path name in debug log when path is deactivated
thunderbolt: Make tb_tunnel_one_dp() return void
thunderbolt: Increase DPRX capabilities read timeout
thunderbolt: Debug log an invalid config space reply just once
thunderbolt: Log config space when invalid config space reply is received
thunderbolt: Drop doubled empty line from ctl.h
thunderbolt: debugfs: Add write capability to path config space
|
