| Age | Commit message (Collapse) | Author |
|---|
|
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507bf ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.
This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When commit 28b2e0d2cd13 ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().
However, once commit 88d6272acaaa ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().
This commit removes that initialization to restore the proper
functionality.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
I noticed that when probed with ti-sysc, watchdog can trigger on am3, am4
and dra7 causing a device reset.
Turns out I made several mistakes implementing the watchdog quirk handling:
1. We must do both writes to spr register
2. We must also call the reset quirk on disable
3. On am3 and am4 we need to also set swsup quirk flag
I probably only tested this earlier with watchdog service running when the
watchdog never gets disabled.
Fixes: 4e23be473e30 ("bus: ti-sysc: Add support for module specific reset quirks")
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"Fix possible use-after-free in the ACPI CPPC support code (John Garry)
and prevent the ACPI HMAT parsing code from using possibly incorrect
data coming from the platform firmware (Daniel Black)"
* tag 'acpi-5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Set pcc_data[pcc_ss_id] to NULL in acpi_cppc_processor_exit()
ACPI: HMAT: ACPI_HMAT_MEMORY_PD_VALID is deprecated since ACPI-6.3
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These include a fix for a recent regression in the ACPI CPU
performance scaling code, a PCI device power management fix,
a system shutdown fix related to cpufreq, a removal of an ACPI
suspend-to-idle blacklist entry and a build warning fix.
Specifics:
- Fix possible NULL pointer dereference in the ACPI processor scaling
initialization code introduced by a recent cpufreq update (Rafael
Wysocki).
- Fix possible deadlock due to suspending cpufreq too late during
system shutdown (Rafael Wysocki).
- Make the PCI device system resume code path be more consistent with
its PM-runtime counterpart to fix an issue with missing delay on
transitions from D3cold to D0 during system resume from
suspend-to-idle on some systems (Rafael Wysocki).
- Drop Dell XPS13 9360 from the LPS0 Idle _DSM blacklist to make it
use suspend-to-idle by default (Mario Limonciello).
- Fix build warning in the core system suspend support code (Ben
Dooks)"
* tag 'pm-5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Avoid NULL pointer dereferences at init time
PCI: PM: Fix pci_power_up()
PM: sleep: include <linux/pm_runtime.h> for pm_wq
cpufreq: Avoid cpufreq_suspend() deadlock on system shutdown
ACPI: PM: Drop Dell XPS13 9360 from LPS0 Idle _DSM blacklist
|
|
We must return a mask covering the full physical RAM when bypassing the
IOMMU mapping. Also, in iommu_need_mapping, we need to check using
dma_direct_get_required_mask to ensure that the device's dma_mask can
cover physical RAM before deciding to bypass IOMMU mapping.
Based on an earlier patch from Christoph Hellwig.
Fixes: 249baa547901 ("dma-mapping: provide a better default ->get_required_mask")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi
Pull scsi fixes from Martin Petersen:
"These two commits were in a separate postmerge branch due to a
dependency on changes merged for 5.4 in the block tree.
They fix two issues in the intersection of the request cleanup changes
from block (b7e9e1fb7a92) and the request batching changes
(8930a6c20791) that were made to SCSI during the 5.4 cycle"
* tag 'mkp-scsi-postmerge' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi:
scsi: core: fix dh and multipathing for SCSI hosts without request batching
scsi: core: fix missing .cleanup_rq for SCSI hosts without request batching
|
|
The increase_address_space() function has to check the PM_LEVEL_SIZE()
condition again under the domain->lock to avoid a false trigger of the
WARN_ON_ONCE() and to avoid that the address space is increase more
often than necessary.
Reported-by: Qian Cai <cai@lca.pw>
Fixes: 754265bcab78 ("iommu/amd: Fix race in increase_address_space()")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Pull NVMe updates from Keith:
"This is a collection of bug fixes committed since the previous pull
request that address deadlocks, double resets, memory leaks, and other
regression."
* 'nvme-5.4' of git://git.infradead.org/nvme:
nvme-pci: Set the prp2 correctly when using more than 4k page
nvme-tcp: fix possible leakage during error flow
nvmet-loop: fix possible leakage during error flow
nvme-tcp: Initialize sk->sk_ll_usec only with NET_RX_BUSY_POLL
nvme: Wait for reset state when required
nvme: Prevent resets during paused controller state
nvme: Restart request timers in resetting state
nvme: Remove ADMIN_ONLY state
nvme-pci: Free tagset if no IO queues
nvme: retain split access workaround for capability reads
nvme: fix possible deadlock when nvme_update_formats fails
|
|
In the current code, the nvme is using a fixed 4k PRP entry size,
but if the kernel use a page size which is more than 4k, we should
consider the situation that the bv_offset may be larger than the
dev->ctrl.page_size. Otherwise we may miss setting the prp2 and then
cause the command can't be executed correctly.
Fixes: dff824b2aadb ("nvme-pci: optimize mapping of small single segment requests")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
The Primebook C11B uses the SIPODEV SP1064 touchpad. There are 2 versions
of this 2-in-1 and the touchpad in the older version does not supply
descriptors, so it has to be added to the override list.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
All of the FF-related resources belong to corresponding FF device, so
they should be freed as a part of hidpp_ff_destroy() to avoid
potential race condidions.
Fixes: ff21a635dd1a ("HID: logitech-hidpp: Force feedback support for the Logitech G920")
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Henrik Rydberg <rydberg@bitmath.org>
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Cc: Austin Palmer <austinp@valvesoftware.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 5.2+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
G920 device only advertises REPORT_ID_HIDPP_LONG and
REPORT_ID_HIDPP_VERY_LONG in its HID report descriptor, so querying
for REPORT_ID_HIDPP_SHORT with optional=false will always fail and
prevent G920 to be recognized as a valid HID++ device.
To fix this and improve some other aspects, modify
hidpp_validate_device() as follows:
- Inline the code of hidpp_validate_report() to simplify
distingushing between non-present and invalid report descriptors
- Drop the check for id >= HID_MAX_IDS || id < 0 since all of our
IDs are static and known to satisfy that at compile time
- Change the algorithms to check all possible report
types (including very long report) and deem the device as a valid
HID++ device if it supports at least one
- Treat invalid report length as a hard stop for the validation
algorithm, meaning that if any of the supported reports has
invalid length we assume the worst and treat the device as a
generic HID device.
- Fold initialization of hidpp->very_long_report_length into
hidpp_validate_device() since it already fetches very long report
length and validates its value
Fixes: fe3ee1ec007b ("HID: logitech-hidpp: allow non HID++ devices to be handled by this module")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204191
Reported-by: Sam Bazely <sambazley@fastmail.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Henrik Rydberg <rydberg@bitmath.org>
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Cc: Austin Palmer <austinp@valvesoftware.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 5.2+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Original version of g920_get_config() contained two kind of actions:
1. Device specific communication to query/set some parameters
which requires active communication channel with the device,
or, put in other way, for the call to be sandwiched between
hid_device_io_start() and hid_device_io_stop().
2. Input subsystem specific FF controller initialization which, in
order to access a valid 'struct hid_input' via
'hid->inputs.next', requires claimed hidinput which means be
executed after the call to hid_hw_start() with connect_mask
containing HID_CONNECT_HIDINPUT.
Location of g920_get_config() can only fulfill requirements for #1 and
not #2, which might result in following backtrace:
[ 88.312258] logitech-hidpp-device 0003:046D:C262.0005: HID++ 4.2 device connected.
[ 88.320298] BUG: kernel NULL pointer dereference, address: 0000000000000018
[ 88.320304] #PF: supervisor read access in kernel mode
[ 88.320307] #PF: error_code(0x0000) - not-present page
[ 88.320309] PGD 0 P4D 0
[ 88.320315] Oops: 0000 [#1] SMP PTI
[ 88.320320] CPU: 1 PID: 3080 Comm: systemd-udevd Not tainted 5.4.0-rc1+ #31
[ 88.320322] Hardware name: Apple Inc. MacBookPro11,1/Mac-189A3D4F975D5FFC, BIOS 149.0.0.0.0 09/17/2018
[ 88.320334] RIP: 0010:hidpp_probe+0x61f/0x948 [hid_logitech_hidpp]
[ 88.320338] Code: 81 00 00 48 89 ef e8 f0 d6 ff ff 41 89 c6 85 c0 75 b5 0f b6 44 24 28 48 8b 5d 00 88 44 24 1e 89 44 24 0c 48 8b 83 18 1c 00 00 <48> 8b 48 18 48 8b 83 10 19 00 00 48 8b 40 40 48 89 0c 24 0f b7 80
[ 88.320341] RSP: 0018:ffffb0a6824aba68 EFLAGS: 00010246
[ 88.320345] RAX: 0000000000000000 RBX: ffff93a50756e000 RCX: 0000000000010408
[ 88.320347] RDX: 0000000000000000 RSI: ffff93a51f0ad0a0 RDI: 000000000002d0a0
[ 88.320350] RBP: ffff93a50416da28 R08: ffff93a50416da70 R09: ffff93a50416da70
[ 88.320352] R10: 000000148ae9e60c R11: 00000000000f1525 R12: ffff93a50756e000
[ 88.320354] R13: ffff93a50756f8d0 R14: 0000000000000000 R15: ffff93a50756fc38
[ 88.320358] FS: 00007f8d8c1e0940(0000) GS:ffff93a51f080000(0000) knlGS:0000000000000000
[ 88.320361] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 88.320363] CR2: 0000000000000018 CR3: 00000003996d8003 CR4: 00000000001606e0
[ 88.320366] Call Trace:
[ 88.320377] ? _cond_resched+0x15/0x30
[ 88.320387] ? create_pinctrl+0x2f/0x3c0
[ 88.320393] ? kernfs_link_sibling+0x94/0xe0
[ 88.320398] ? _cond_resched+0x15/0x30
[ 88.320402] ? kernfs_activate+0x5f/0x80
[ 88.320406] ? kernfs_add_one+0xe2/0x130
[ 88.320411] hid_device_probe+0x106/0x170
[ 88.320419] really_probe+0x147/0x3c0
[ 88.320424] driver_probe_device+0xb6/0x100
[ 88.320428] device_driver_attach+0x53/0x60
[ 88.320433] __driver_attach+0x8a/0x150
[ 88.320437] ? device_driver_attach+0x60/0x60
[ 88.320440] bus_for_each_dev+0x78/0xc0
[ 88.320445] bus_add_driver+0x14d/0x1f0
[ 88.320450] driver_register+0x6c/0xc0
[ 88.320453] ? 0xffffffffc0d67000
[ 88.320457] __hid_register_driver+0x4c/0x80
[ 88.320464] do_one_initcall+0x46/0x1f4
[ 88.320469] ? _cond_resched+0x15/0x30
[ 88.320474] ? kmem_cache_alloc_trace+0x162/0x220
[ 88.320481] ? do_init_module+0x23/0x230
[ 88.320486] do_init_module+0x5c/0x230
[ 88.320491] load_module+0x26e1/0x2990
[ 88.320502] ? ima_post_read_file+0xf0/0x100
[ 88.320508] ? __do_sys_finit_module+0xaa/0x110
[ 88.320512] __do_sys_finit_module+0xaa/0x110
[ 88.320520] do_syscall_64+0x5b/0x180
[ 88.320525] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 88.320528] RIP: 0033:0x7f8d8d1f01fd
[ 88.320532] Code: 00 c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 5b 8c 0c 00 f7 d8 64 89 01 48
[ 88.320535] RSP: 002b:00007ffefa3bb068 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
[ 88.320539] RAX: ffffffffffffffda RBX: 000055922040cb40 RCX: 00007f8d8d1f01fd
[ 88.320541] RDX: 0000000000000000 RSI: 00007f8d8ce4984d RDI: 0000000000000006
[ 88.320543] RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000007
[ 88.320545] R10: 0000000000000006 R11: 0000000000000246 R12: 00007f8d8ce4984d
[ 88.320547] R13: 0000000000000000 R14: 000055922040efc0 R15: 000055922040cb40
[ 88.320551] Modules linked in: hid_logitech_hidpp(+) fuse rfcomm ccm xt_CHECKSUM xt_MASQUERADE bridge stp llc nf_nat_tftp nf_conntrack_tftp nf_conntrack_netbios_ns nf_conntrack_broadcast xt_CT ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 xt_conntrack ebtable_nat ip6table_nat ip6table_mangle ip6table_raw ip6table_security iptable_nat nf_nat tun iptable_mangle iptable_raw iptable_security nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 libcrc32c ip_set nfnetlink ebtable_filter ebtables ip6table_filter ip6_tables cmac bnep sunrpc dm_crypt nls_utf8 hfsplus intel_rapl_msr intel_rapl_common ath9k_htc ath9k_common x86_pkg_temp_thermal intel_powerclamp b43 ath9k_hw coretemp snd_hda_codec_hdmi cordic kvm_intel snd_hda_codec_cirrus mac80211 snd_hda_codec_generic ledtrig_audio kvm snd_hda_intel snd_intel_nhlt irqbypass snd_hda_codec btusb btrtl snd_hda_core ath btbcm ssb snd_hwdep btintel snd_seq crct10dif_pclmul iTCO_wdt snd_seq_device crc32_pclmul bluetooth mmc_core iTCO_vendor_support joydev cfg80211
[ 88.320602] applesmc ghash_clmulni_intel ecdh_generic snd_pcm input_polldev intel_cstate ecc intel_uncore thunderbolt snd_timer i2c_i801 libarc4 rfkill intel_rapl_perf lpc_ich mei_me pcspkr bcm5974 snd bcma mei soundcore acpi_als sbs kfifo_buf sbshc industrialio apple_bl i915 i2c_algo_bit drm_kms_helper drm uas crc32c_intel usb_storage video hid_apple
[ 88.320630] CR2: 0000000000000018
[ 88.320633] ---[ end trace 933491c8a4fadeb7 ]---
[ 88.320642] RIP: 0010:hidpp_probe+0x61f/0x948 [hid_logitech_hidpp]
[ 88.320645] Code: 81 00 00 48 89 ef e8 f0 d6 ff ff 41 89 c6 85 c0 75 b5 0f b6 44 24 28 48 8b 5d 00 88 44 24 1e 89 44 24 0c 48 8b 83 18 1c 00 00 <48> 8b 48 18 48 8b 83 10 19 00 00 48 8b 40 40 48 89 0c 24 0f b7 80
[ 88.320647] RSP: 0018:ffffb0a6824aba68 EFLAGS: 00010246
[ 88.320650] RAX: 0000000000000000 RBX: ffff93a50756e000 RCX: 0000000000010408
[ 88.320652] RDX: 0000000000000000 RSI: ffff93a51f0ad0a0 RDI: 000000000002d0a0
[ 88.320655] RBP: ffff93a50416da28 R08: ffff93a50416da70 R09: ffff93a50416da70
[ 88.320657] R10: 000000148ae9e60c R11: 00000000000f1525 R12: ffff93a50756e000
[ 88.320659] R13: ffff93a50756f8d0 R14: 0000000000000000 R15: ffff93a50756fc38
[ 88.320662] FS: 00007f8d8c1e0940(0000) GS:ffff93a51f080000(0000) knlGS:0000000000000000
[ 88.320664] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 88.320667] CR2: 0000000000000018 CR3: 00000003996d8003 CR4: 00000000001606e0
To solve this issue:
1. Split g920_get_config() such that all of the device specific
communication remains a part of the function and input subsystem
initialization bits go to hidpp_ff_init()
2. Move call to hidpp_ff_init() from being a part of
g920_get_config() to be the last step of .probe(), right after a
call to hid_hw_start() with connect_mask containing
HID_CONNECT_HIDINPUT.
Fixes: 91cf9a98ae41 ("HID: logitech-hidpp: make .probe usbhid capable")
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-by: Sam Bazley <sambazley@fastmail.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: Henrik Rydberg <rydberg@bitmath.org>
Cc: Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>
Cc: Austin Palmer <austinp@valvesoftware.com>
Cc: linux-input@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 5.2+
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Runtime power management in i2c-hid brings lots of issues, such as:
- When transitioning from display manager to desktop session, i2c-hid
was closed and opened, so the device was set to SLEEP and ON in a short
period. Vendors confirmed that their devices can't handle fast ON/SLEEP
command because Windows doesn't have this behavior.
- When rebooting, i2c-hid was closed, and the driver core put the device
back to full power before shutdown. This behavior also triggers a quick
SLEEP and ON commands that some devices can't handle, renders an
unusable touchpad after reboot.
- Most importantly, my power meter reports little to none energy saving
when i2c-hid is runtime suspended.
So let's remove runtime power management since there is no actual
benefit.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
* acpi-tables:
ACPI: HMAT: ACPI_HMAT_MEMORY_PD_VALID is deprecated since ACPI-6.3
|
|
When enabling KASAN and DEBUG_TEST_DRIVER_REMOVE, I find this KASAN
warning:
[ 20.872057] BUG: KASAN: use-after-free in pcc_data_alloc+0x40/0xb8
[ 20.878226] Read of size 4 at addr ffff00236cdeb684 by task swapper/0/1
[ 20.884826]
[ 20.886309] CPU: 19 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc1-00009-ge7f7df3db5bf-dirty #289
[ 20.894994] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.16.01 03/15/2019
[ 20.903505] Call trace:
[ 20.905942] dump_backtrace+0x0/0x200
[ 20.909593] show_stack+0x14/0x20
[ 20.912899] dump_stack+0xd4/0x130
[ 20.916291] print_address_description.isra.9+0x6c/0x3b8
[ 20.921592] __kasan_report+0x12c/0x23c
[ 20.925417] kasan_report+0xc/0x18
[ 20.928808] __asan_load4+0x94/0xb8
[ 20.932286] pcc_data_alloc+0x40/0xb8
[ 20.935938] acpi_cppc_processor_probe+0x4e8/0xb08
[ 20.940717] __acpi_processor_start+0x48/0xb0
[ 20.945062] acpi_processor_start+0x40/0x60
[ 20.949235] really_probe+0x118/0x548
[ 20.952887] driver_probe_device+0x7c/0x148
[ 20.957059] device_driver_attach+0x94/0xa0
[ 20.961231] __driver_attach+0xa4/0x110
[ 20.965055] bus_for_each_dev+0xe8/0x158
[ 20.968966] driver_attach+0x30/0x40
[ 20.972531] bus_add_driver+0x234/0x2f0
[ 20.976356] driver_register+0xbc/0x1d0
[ 20.980182] acpi_processor_driver_init+0x40/0xe4
[ 20.984875] do_one_initcall+0xb4/0x254
[ 20.988700] kernel_init_freeable+0x24c/0x2f8
[ 20.993047] kernel_init+0x10/0x118
[ 20.996524] ret_from_fork+0x10/0x18
[ 21.000087]
[ 21.001567] Allocated by task 1:
[ 21.004785] save_stack+0x28/0xc8
[ 21.008089] __kasan_kmalloc.isra.9+0xbc/0xd8
[ 21.012435] kasan_kmalloc+0xc/0x18
[ 21.015913] pcc_data_alloc+0x94/0xb8
[ 21.019564] acpi_cppc_processor_probe+0x4e8/0xb08
[ 21.024343] __acpi_processor_start+0x48/0xb0
[ 21.028689] acpi_processor_start+0x40/0x60
[ 21.032860] really_probe+0x118/0x548
[ 21.036512] driver_probe_device+0x7c/0x148
[ 21.040684] device_driver_attach+0x94/0xa0
[ 21.044855] __driver_attach+0xa4/0x110
[ 21.048680] bus_for_each_dev+0xe8/0x158
[ 21.052591] driver_attach+0x30/0x40
[ 21.056155] bus_add_driver+0x234/0x2f0
[ 21.059980] driver_register+0xbc/0x1d0
[ 21.063805] acpi_processor_driver_init+0x40/0xe4
[ 21.068497] do_one_initcall+0xb4/0x254
[ 21.072322] kernel_init_freeable+0x24c/0x2f8
[ 21.076667] kernel_init+0x10/0x118
[ 21.080144] ret_from_fork+0x10/0x18
[ 21.083707]
[ 21.085186] Freed by task 1:
[ 21.088056] save_stack+0x28/0xc8
[ 21.091360] __kasan_slab_free+0x118/0x180
[ 21.095445] kasan_slab_free+0x10/0x18
[ 21.099183] kfree+0x80/0x268
[ 21.102139] acpi_cppc_processor_exit+0x1a8/0x1b8
[ 21.106832] acpi_processor_stop+0x70/0x80
[ 21.110917] really_probe+0x174/0x548
[ 21.114568] driver_probe_device+0x7c/0x148
[ 21.118740] device_driver_attach+0x94/0xa0
[ 21.122912] __driver_attach+0xa4/0x110
[ 21.126736] bus_for_each_dev+0xe8/0x158
[ 21.130648] driver_attach+0x30/0x40
[ 21.134212] bus_add_driver+0x234/0x2f0
[ 21.0x10/0x18
[ 21.161764]
[ 21.163244] The buggy address belongs to the object at ffff00236cdeb600
[ 21.163244] which belongs to the cache kmalloc-256 of size 256
[ 21.175750] The buggy address is located 132 bytes inside of
[ 21.175750] 256-byte region [ffff00236cdeb600, ffff00236cdeb700)
[ 21.187473] The buggy address belongs to the page:
[ 21.192254] page:fffffe008d937a00 refcount:1 mapcount:0 mapping:ffff002370c0fa00 index:0x0 compound_mapcount: 0
[ 21.202331] flags: 0x1ffff00000010200(slab|head)
[ 21.206940] raw: 1ffff00000010200 dead000000000100 dead000000000122 ffff002370c0fa00
[ 21.214671] raw: 0000000000000000 00000000802a002a 00000001ffffffff 0000000000000000
[ 21.222400] page dumped because: kasan: bad access detected
[ 21.227959]
[ 21.229438] Memory state around the buggy address:
[ 21.234218] ffff00236cdeb580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 21.241427] ffff00236cdeb600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.248637] >ffff00236cdeb680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.255845] ^
[ 21.259062] ffff00236cdeb700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 21.266272] ffff00236cdeb780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.273480] ==================================================================
It seems that global pcc_data[pcc_ss_id] can be freed in
acpi_cppc_processor_exit(), but we may later reference this value, so
NULLify it when freed.
Also remove the useless setting of data "pcc_channel_acquired", which
we're about to free.
Fixes: 85b1407bf6d2 ("ACPI / CPPC: Make CPPC ACPI driver aware of PCC subspace IDs")
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-cpufreq:
ACPI: processor: Avoid NULL pointer dereferences at init time
cpufreq: Avoid cpufreq_suspend() deadlock on system shutdown
* pm-sleep:
PM: sleep: include <linux/pm_runtime.h> for pm_wq
ACPI: PM: Drop Dell XPS13 9360 from LPS0 Idle _DSM blacklist
|
|
bam_dma_terminate_all() will leak resources if any of the transactions are
committed to the hardware (present in the desc fifo), and not complete.
Since bam_dma_terminate_all() does not cause the hardware to be updated,
the hardware will still operate on any previously committed transactions.
This can cause memory corruption if the memory for the transaction has been
reassigned, and will cause a sync issue between the BAM and its client(s).
Fix this by properly updating the hardware in bam_dma_terminate_all().
Fixes: e7c0fe2a5c84 ("dmaengine: add Qualcomm BAM dma driver")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191017152606.34120-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The BUILD_NVME define never got defined anywhere, causing NVMe commands to
be treated as SCSI commands when freeing the buffers. This was causing a
stuck discovery and a horrible crash in lpfc_set_rrq_active() later on.
Link: https://lore.kernel.org/r/20191017150019.75769-1-hare@suse.de
Fixes: c00f62e6c546 ("scsi: lpfc: Merge per-protocol WQ/CQ pairs into single per-cpu pair")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
We have a test case like block/001 in blktests, which will create a scsi
device by loading scsi_debug module and then try to delete the device by
sysfs interface. At the same time, it may remove the scsi_debug module.
And getting a invalid paging request BUG_ON as following:
[ 34.625854] BUG: unable to handle page fault for address: ffffffffa0016bb8
[ 34.629189] Oops: 0000 [#1] SMP PTI
[ 34.629618] CPU: 1 PID: 450 Comm: bash Tainted: G W 5.4.0-rc3+ #473
[ 34.632524] RIP: 0010:scsi_proc_hostdir_rm+0x5/0xa0
[ 34.643555] CR2: ffffffffa0016bb8 CR3: 000000012cd88000 CR4: 00000000000006e0
[ 34.644545] Call Trace:
[ 34.644907] scsi_host_dev_release+0x6b/0x1f0
[ 34.645511] device_release+0x74/0x110
[ 34.646046] kobject_put+0x116/0x390
[ 34.646559] put_device+0x17/0x30
[ 34.647041] scsi_target_dev_release+0x2b/0x40
[ 34.647652] device_release+0x74/0x110
[ 34.648186] kobject_put+0x116/0x390
[ 34.648691] put_device+0x17/0x30
[ 34.649157] scsi_device_dev_release_usercontext+0x2e8/0x360
[ 34.649953] execute_in_process_context+0x29/0x80
[ 34.650603] scsi_device_dev_release+0x20/0x30
[ 34.651221] device_release+0x74/0x110
[ 34.651732] kobject_put+0x116/0x390
[ 34.652230] sysfs_unbreak_active_protection+0x3f/0x50
[ 34.652935] sdev_store_delete.cold.4+0x71/0x8f
[ 34.653579] dev_attr_store+0x1b/0x40
[ 34.654103] sysfs_kf_write+0x3d/0x60
[ 34.654603] kernfs_fop_write+0x174/0x250
[ 34.655165] __vfs_write+0x1f/0x60
[ 34.655639] vfs_write+0xc7/0x280
[ 34.656117] ksys_write+0x6d/0x140
[ 34.656591] __x64_sys_write+0x1e/0x30
[ 34.657114] do_syscall_64+0xb1/0x400
[ 34.657627] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 34.658335] RIP: 0033:0x7f156f337130
During deleting scsi target, the scsi_debug module have been removed. Then,
sdebug_driver_template belonged to the module cannot be accessd, resulting
in scsi_proc_hostdir_rm() BUG_ON.
To fix the bug, we add scsi_device_get() in sdev_store_delete() to try to
increase refcount of module, avoiding the module been removed.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191015130556.18061-1-yuyufen@huawei.com
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct returning from reset before outstanding commands are completed
for the device.
Link: https://lore.kernel.org/r/157107623870.17997.11208813089704833029.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
passthrough_parse_cdb() - used by TCMU and PSCSI - attepts to reset the LUN
field of SCSI-2 CDBs (bits 5,6,7 of byte 1). The current code is wrong as
for newer commands not having the LUN field it overwrites relevant command
bits (e.g. for SECURITY PROTOCOL IN / OUT). We think this code was
unnecessary from the beginning or at least it is no longer useful. So we
remove it entirely.
Link: https://lore.kernel.org/r/12498eab-76fd-eaad-1316-c2827badb76a@ts.fujitsu.com
Signed-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to allocate a large enough buffer for the
feedback buffer, otherwise the IB test can overwrite
other memory.
Reviewed-by: James Zhu <James.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We need to drop normal and userptr BOs separately.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
When we allocate new page tables under memory
pressure we should not evict old ones.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
user_pages array should always be freed after validation regardless if
user pages are changed after bo is created because with HMM change parse
bo always allocate user pages array to get user pages for userptr bo.
v2: remove unused local variable and amend commit
v3: add back get user pages in gem_userptr_ioctl, to detect application
bug where an userptr VMA is not ananymous memory and reject it.
Bugzilla: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1844962
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Tested-by: Joe Barnett <thejoe@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.3
|
|
We need to allocate a large enough buffer for the
session info, otherwise the IB test can overwrite
other memory.
- Session info is 128K according to mesa
- Use the same session info for create and destroy
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=204241
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We need to allocate a large enough buffer for the
session info, otherwise the IB test can overwrite
other memory.
v2: - session info is 128K according to mesa
- use the same session info for create and destroy
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=204241
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
We need to allocate a large enough buffer for the
session info, otherwise the IB test can overwrite
other memory.
v2: - session info is 128K according to mesa
- use the same session info for create and destroy
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=204241
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: James Zhu <James.Zhu@amd.com>
Tested-by: James Zhu <James.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Pull drm fixes from Dave Airlie:
"This is this weeks fixes for drm.
The dma-resv one is probably the more important one a fair few people
have reported it, besides that it's a couple of panfrost, a few i915
and a few amdgpu fixes.
One radeon patch to fix some ppc64 related issues caused an x86
regression so is getting reverted for now.
Summary:
dma-resv:
- shared fences for lima/panfrost
ttm:
- prefault regression fix
- lifetime fix
panfrost:
- stopped job timeout fix
- missing register values
amdgpu:
- smu7 powerplay fix
- bail earlier for cik/si detection
- navi SDMA fix
radeon:
- revert a ppc64 shutdown fix that broke x86
i915:
- VBT information handling fix
- Circular locking fix
- preemption vs resubmission virtual requests fix"
* tag 'drm-fixes-2019-10-18' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Fixup preempt-to-busy vs resubmission of a virtual request
drm/i915/userptr: Never allow userptr into the mappable GGTT
drm/i915: Favor last VBT child device with conflicting AUX ch/DDC pin
drm/i915/execlists: Refactor -EIO markup of hung requests
drm/panfrost: Handle resetting on timeout better
drm/panfrost: Add missing GPU feature registers
drm/ttm: fix handling in ttm_bo_add_mem_to_lru
drm/ttm: Restore ttm prefaulting
drm/ttm: fix busy reference in ttm_mem_evict_first
drm/amdgpu/sdma5: fix mask value of POLL_REGMEM packet for pipe sync
drm/amdgpu: Bail earlier when amdgpu.cik_/si_support is not set to 1
Revert "drm/radeon: Fix EEH during kexec"
drm/msm/dsi: Implement reset correctly
dma-buf/resv: fix exclusive fence get
drm/edid: Add 6 bpc quirk for SDC panel in Lenovo G50
drm/tiny: Kconfig: Remove always-y THERMAL dep. from TINYDRM_REPAPER
drm/amdgpu/powerplay: fix typo in mvdd table setup
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
-dma-resv: Change shared_count to post-increment to fix lima crash (Qiang)
-ttm: A couple fixes related to lifetime and restore prefault behavior
(Christian & Thomas)
-panfrost: Fill in missing feature reg values and fix stoppedjob timeouts
(Steven)
Cc: Qiang Yu <yuq825@gmail.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Steven Price <steven.price@arm.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191017203419.GA142909@art_vandelay
|
|
There is no reason for a different pad buffer for the two
packet types.
Expand the current buffer allocation to allow for both
packet types.
Fixes: f8195f3b14a0 ("IB/hfi1: Eliminate allocation while atomic")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kaike Wan <kaike.wan@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Link: https://lore.kernel.org/r/20191004204934.26838.13099.stgit@awfm-01.aw.intel.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
A TID RDMA READ request could be retried under one of the following
conditions:
- The RC retry timer expires;
- A later TID RDMA READ RESP packet is received before the next
expected one.
For the latter, under normal conditions, the PSN in IB space is used
for comparison. More specifically, the IB PSN in the incoming TID RDMA
READ RESP packet is compared with the last IB PSN of a given TID RDMA
READ request to determine if the request should be retried. This is
similar to the retry logic for noraml RDMA READ request.
However, if a TID RDMA READ RESP packet is lost due to congestion,
header suppresion will be disabled and each incoming packet will raise
an interrupt until the hardware flow is reloaded. Under this condition,
each packet KDETH PSN will be checked by software against r_next_psn
and a retry will be requested if the packet KDETH PSN is later than
r_next_psn. Since each TID RDMA READ segment could have up to 64
packets and each TID RDMA READ request could have many segments, we
could make far more retries under such conditions, and thus leading to
RETRY_EXC_ERR status.
This patch fixes the issue by removing the retry when the incoming
packet KDETH PSN is later than r_next_psn. Instead, it resorts to
RC timer and normal IB PSN comparison for any request retry.
Fixes: 9905bf06e890 ("IB/hfi1: Add functions to receive TID RDMA READ response")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Link: https://lore.kernel.org/r/20191004204035.26542.41684.stgit@awfm-01.aw.intel.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.4-2019-10-16:
amdgpu:
- Powerplay fix for SMU7 parts
- Bail earlier when cik/si support is not set to 1
- Fix an SDMA issue on navi
radeon:
- revert a PPC fix which broken x86
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191017022443.3853-1-alexander.deucher@amd.com
|
|
Before QP is closed it changes to ERROR state, when this happens
the QP was left with old rate limit that was already removed from
the table.
Fixes: 7d29f349a4b9 ("IB/mlx5: Properly adjust rate limit on QP state transitions")
Signed-off-by: Rafi Wiener <rafiw@mellanox.com>
Signed-off-by: Oleg Kuporosov <olegk@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Link: https://lore.kernel.org/r/20191002120243.16971-1-leon@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.
To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.
Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stmmac_pcs_ctrl_ane() expects a register address as
argument 1, but for some reason the mac_device_info is
being passed.
Fix the warning (and possible bug) from sparse:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: expected void [noderef] <asn:2> *ioaddr
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: got struct mac_device_info *hw
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c9255 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The serial state information must not be embedded into another
data structure, as this interferes with cache handling for DMA
on architectures without cache coherence..
That would result in data corruption on some architectures
Allocating it separately.
v2: fix syntax error
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"The main change is that we are reverting blanket enablement of SMBus
mode for devices with Elan touchpads that report BIOS release date as
2018+ because there are older boxes with updated BIOSes that still do
not work well in SMbus mode.
We will have to establish whitelist for SMBus mode it looks like"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: elantech - enable SMBus on new (2018+) systems"
Input: synaptics-rmi4 - avoid processing unknown IRQs
Input: soc_button_array - partial revert of support for newer surface devices
Input: goodix - add support for 9-bytes reports
Input: da9063 - fix capability and drop KEY_SLEEP
|
|
git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- Users of Intel P-Unit IPC driver might be surprised by harmless
warning. Thus, switch to API which doesn't issue a warning at all.
- I²C multi-instantiate driver continues to add slave devices even when
IRQ resource is not found. For devices in the market IRQ resource is
mandatory, so, fail the ->probe() of the parent driver to avoid
slaves being probed.
- Avoid compiler warning due to unused variable in Classmate laptop
driver.
* tag 'platform-drivers-x86-v5.4-3' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: i2c-multi-instantiate: Fail the probe if no IRQ provided
platform/x86: intel_punit_ipc: Avoid error message when retrieving IRQ
platform/x86: classmate-laptop: remove unused variable
|
|
GFP_NOWAIT allocation can fail anytime - it doesn't wait for memory being
available and it fails if the mempool is exhausted and there is not enough
memory.
If we go down this path:
map_bio -> mg_start -> alloc_migration -> mempool_alloc(GFP_NOWAIT)
we can see that map_bio() doesn't check the return value of mg_start(),
and the bio is leaked.
If we go down this path:
map_bio -> mg_start -> mg_lock_writes -> alloc_prison_cell ->
dm_bio_prison_alloc_cell_v2 -> mempool_alloc(GFP_NOWAIT) ->
mg_lock_writes -> mg_complete
the bio is ended with an error - it is unacceptable because it could
cause filesystem corruption if the machine ran out of memory
temporarily.
Change GFP_NOWAIT to GFP_NOIO, so that the mempool code will properly
wait until memory becomes available. mempool_alloc with GFP_NOIO can't
fail, so remove the code paths that deal with allocation failure.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"The fixes pertain to a problem with initializing the Intel GPIO
irqchips when adding gpiochips.
Andy fixed it up elegantly by adding a hardware initialization
callback to the struct gpio_irq_chip so let's use this. Tested and
verified on the target hardware"
* tag 'gpio-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: lynxpoint: set default handler to be handle_bad_irq()
gpio: merrifield: Move hardware initialization to callback
gpio: lynxpoint: Move hardware initialization to callback
gpio: intel-mid: Move hardware initialization to callback
gpiolib: Initialize the hardware with a callback
gpio: merrifield: Restore use of irq_base
|
