| Age | Commit message (Collapse) | Author |
|---|
|
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit 71266d9d3936 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7e6 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes: 71266d9d3936 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In commit 4b7618fdc7e6 ("pinctrl: qcom: Add irq_enable callback for
msm gpio") we tried to Ack interrupts during unmask. However, that
patch forgot to check "intr_ack_high" so, presumably, it only worked
for a certain subset of SoCs.
Let's add a small accessor so we don't need to open-code the logic in
both places.
This was found by code inspection. I don't have any access to the
hardware in question nor software that needs the Ack during unmask.
Fixes: 4b7618fdc7e6 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.3.I32d0f4e174d45363b49ab611a13c3da8f1e87d0f@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There's currently a comment in the code saying function 0 is GPIO.
Instead of hardcoding it, let's add a member where an SoC can specify
it. No known SoCs use a number other than 0, but this just makes the
code clearer. NOTE: no SoC code needs to be updated since we can rely
on zero-initialization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.1.I3ad184e3423d8e479bc3e86f5b393abb1704a1d1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some SoCs, eg. mt8183, are using a pinconfig operation bias_set_combo.
The fallback path in mtk_pinconf_adv_pull_set() should also try this
operation.
Fixes: cafe19db7751 ("pinctrl: mediatek: Backward compatible to previous Mediatek's bias-pull usage")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/20201228090425.2130569-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Clang warns:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:952:8: warning: unused
variable 'wake' [-Wunused-variable]
bool wake;
^
1 warning generated.
There were two wake declarations added to nmk_gpio_dbg_show_one when
converting it to use irq_has_action but only one is used within its
scope. Remove the unused one so there is no more warning.
Fixes: f3925032d7fd ("pinctrl: nomadik: Use irq_has_action()")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Halaney <ajhalaney@gmail.com>
Reviewed-by: Andrew Halaney <ajhalaney@gmail.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201229204710.1129033-1-natechancellor@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The SCU offset for signal PWM8 in group PWM8G0 is wrong, fix it from
SCU414 to SCU4B4.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Fixes: 2eda1cdec49f ("pinctrl: aspeed: Add AST2600 pinmux support")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201217024912.3198-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that JZ4760 support has been fixed, it looks wrong to have
JZ4760_GPIO_* registers being written if the SoC is a JZ4770 or later.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-2-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
- JZ4760 and JZ4760B have a similar register layout as the JZ4740, and
don't use the new register layout, which was introduced with the
JZ4770 SoC and not the JZ4760 or JZ4760B SoCs.
- The JZ4740 code path only expected two function modes to be
configurable for each pin, and wouldn't work with more than two. Fix
it for the JZ4760, which has four configurable function modes.
Fixes: 0257595a5cf4 ("pinctrl: Ingenic: Add pinctrl driver for JZ4760 and JZ4760B.")
Cc: <stable@vger.kernel.org> # 5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pull NTB fixes from Jon Mason:
"Bug fix for IDT NTB and Intel NTB LTR management support"
* tag 'ntb-5.11' of git://github.com/jonmason/ntb:
ntb: intel: add Intel NTB LTR vendor support for gen4 NTB
ntb: idt: fix error check in ntb_hw_idt.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"Fix a number of autobuild failures due to missing Kconfig
dependencies"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: qat - add CRYPTO_AES to Kconfig dependencies
crypto: keembay - Add dependency on HAS_IOMEM
crypto: keembay - CRYPTO_DEV_KEEMBAY_OCS_AES_SM4 should depend on ARCH_KEEMBAY
|
|
Commit c9a3c4e637ac ("mfd: ab8500-debugfs: Remove extraneous curly
brace") removed a left-over curly brace that caused build failures, but
Joe Perches points out that the subsequent 'seq_putc()' should also be
removed, because the commit that caused all these problems already added
the final '\n' to the seq_printf() above it.
Reported-by: Joe Perches <joe@perches.com>
Fixes: 886c8121659d ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix a tegra enumeration regression (Rob Herring)
- Fix a designware-host check that warned on *success*, not failure
(Alexander Lobakin)
* tag 'pci-v5.11-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dwc: Fix inverted condition of DMA mask setup warning
PCI: tegra: Fix host link initialization
|
|
Clang errors:
drivers/mfd/ab8500-debugfs.c:1526:2: error: non-void function does not return a value [-Werror,-Wreturn-type]
}
^
drivers/mfd/ab8500-debugfs.c:1528:2: error: expected identifier or '('
return 0;
^
drivers/mfd/ab8500-debugfs.c:1529:1: error: extraneous closing brace ('}')
}
^
3 errors generated.
The cleanup in ab8500_interrupts_show left a curly brace around, remove
it to fix the error.
Fixes: 886c8121659d ("mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 660c486590aa ("PCI: dwc: Set 32-bit DMA mask for MSI target address
allocation") added dma_mask_set() call to explicitly set 32-bit DMA mask
for MSI message mapping, but for now it throws a warning on ret == 0, while
dma_set_mask() returns 0 in case of success.
Fix this by inverting the condition.
[bhelgaas: join string to make it greppable]
Fixes: 660c486590aa ("PCI: dwc: Set 32-bit DMA mask for MSI target address allocation")
Link: https://lore.kernel.org/r/20201222150708.67983-1-alobakin@pm.me
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Commit b9ac0f9dc8ea ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common
code") broke enumeration of downstream devices on Tegra:
In non-working case (next-20201211):
0001:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: NVIDIA Corporation Device 1ad0 (rev a1)
In working case (v5.10-rc7):
0001:00:00.0 PCI bridge: Molex Incorporated Device 1ad2 (rev a1)
0001:01:00.0 SATA controller: Marvell Technology Group Ltd. Device 9171 (rev 13)
0005:00:00.0 PCI bridge: Molex Incorporated Device 1ad0 (rev a1)
0005:01:00.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:02:02.0 PCI bridge: PLX Technology, Inc. Device 3380 (rev ab)
0005:03:00.0 USB controller: PLX Technology, Inc. Device 3380 (rev ab)
The problem seems to be dw_pcie_setup_rc() is now called twice before and
after the link up handling. The fix is to move Tegra's link up handling to
.start_link() function like other DWC drivers. Tegra is a bit more
complicated than others as it re-inits the whole DWC controller to retry
the link. With this, the initialization ordering is restored to match the
prior sequence.
Fixes: b9ac0f9dc8ea ("PCI: dwc: Move dw_pcie_setup_rc() to DWC common code")
Link: https://lore.kernel.org/r/20201218143905.1614098-1-robh@kernel.org
Reported-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Tested-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
|
|
clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.
This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.
So just initialize 'val' to zero to avoid the issue.
Fixes: 110b055b2827 ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is the second attempt after the first one failed miserably and
got zapped to unblock the rest of the interrupt related patches.
A treewide cleanup of interrupt descriptor (ab)use with all sorts of
racy accesses, inefficient and disfunctional code. The goal is to
remove the export of irq_to_desc() to prevent these things from
creeping up again"
* tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
genirq: Restrict export of irq_to_desc()
xen/events: Implement irq distribution
xen/events: Reduce irq_info:: Spurious_cnt storage size
xen/events: Only force affinity mask for percpu interrupts
xen/events: Use immediate affinity setting
xen/events: Remove disfunct affinity spreading
xen/events: Remove unused bind_evtchn_to_irq_lateeoi()
net/mlx5: Use effective interrupt affinity
net/mlx5: Replace irq_to_desc() abuse
net/mlx4: Use effective interrupt affinity
net/mlx4: Replace irq_to_desc() abuse
PCI: mobiveil: Use irq_data_get_irq_chip_data()
PCI: xilinx-nwl: Use irq_data_get_irq_chip_data()
NTB/msi: Use irq_has_action()
mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc
pinctrl: nomadik: Use irq_has_action()
drm/i915/pmu: Replace open coded kstat_irqs() copy
drm/i915/lpe_audio: Remove pointless irq_to_desc() usage
s390/irq: Use irq_desc_kstat_cpu() in show_msi_interrupt()
parisc/irq: Use irq_desc_kstat_cpu() in show_interrupts()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Borislav Petkov:
"These got delayed due to a last minute ia64 build issue which got
fixed in the meantime.
EFI updates collected by Ard Biesheuvel:
- Don't move BSS section around pointlessly in the x86 decompressor
- Refactor helper for discovering the EFI secure boot mode
- Wire up EFI secure boot to IMA for arm64
- Some fixes for the capsule loader
- Expose the RT_PROP table via the EFI test module
- Relax DT and kernel placement restrictions on ARM
with a few followup fixes:
- fix the build breakage on IA64 caused by recent capsule loader
changes
- suppress a type mismatch build warning in the expansion of
EFI_PHYS_ALIGN on ARM"
* tag 'efi_updates_for_v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: arm: force use of unsigned type for EFI_PHYS_ALIGN
efi: ia64: disable the capsule loader
efi: stub: get rid of efi_get_max_fdt_addr()
efi/efi_test: read RuntimeServicesSupported
efi: arm: reduce minimum alignment of uncompressed kernel
efi: capsule: clean scatter-gather entries from the D-cache
efi: capsule: use atomic kmap for transient sglist mappings
efi: x86/xen: switch to efi_get_secureboot_mode helper
arm64/ima: add ima_arch support
ima: generalize x86/EFI arch glue for other EFI architectures
efi: generalize efi_get_secureboot
efi/libstub: EFI_GENERIC_STUB_INITRD_CMDLINE_LOADER should not default to yes
efi/x86: Only copy the compressed kernel image in efi_relocate_kernel()
efi/libstub/x86: simplify efi_is_native()
|
|
Pull block fixes from Jens Axboe:
"A few stragglers in here, but mostly just straight fixes. In
particular:
- Set of rnbd fixes for issues around changes for the merge window
(Gioh, Jack, Md Haris Iqbal)
- iocost tracepoint addition (Baolin)
- Copyright/maintainers update (Christoph)
- Remove old blk-mq fast path CPU warning (Daniel)
- loop max_part fix (Josh)
- Remote IPI threaded IRQ fix (Sebastian)
- dasd stable fixes (Stefan)
- bcache merge window fixup and style fixup (Yi, Zheng)"
* tag 'block-5.11-2020-12-23' of git://git.kernel.dk/linux-block:
md/bcache: convert comma to semicolon
bcache:remove a superfluous check in register_bcache
block: update some copyrights
block: remove a pointless self-reference in block_dev.c
MAINTAINERS: add fs/block_dev.c to the block section
blk-mq: Don't complete on a remote CPU in force threaded mode
s390/dasd: fix list corruption of lcu list
s390/dasd: fix list corruption of pavgroup group list
s390/dasd: prevent inconsistent LCU device data
s390/dasd: fix hanging device offline processing
blk-iocost: Add iocg idle state tracepoint
nbd: Respect max_part for all partition scans
block/rnbd-clt: Does not request pdu to rtrs-clt
block/rnbd-clt: Dynamically allocate sglist for rnbd_iu
block/rnbd: Set write-back cache and fua same to the target device
block/rnbd: Fix typos
block/rnbd-srv: Protect dev session sysfs removal
block/rnbd-clt: Fix possible memleak
block/rnbd-clt: Get rid of warning regarding size argument in strlcpy
blk-mq: Remove 'running from the wrong CPU' warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm updates from Dan Williams:
"Twas the day before Christmas and the only thing stirring in libnvdimm
/ device-dax land is a pile of miscellaneous fixups and cleanups.
The bulk of it has appeared in -next save the last two patches to
device-dax that have passed my build and unit tests.
- Fix a long standing block-window-namespace issue surfaced by the
ndctl change to attempt to preserve the kernel device name over
a 'reconfigure'
- Fix a few error path memory leaks in nfit and device-dax
- Silence a smatch warning in the ioctl path
- Miscellaneous cleanups"
* tag 'libnvdimm-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: Avoid an unnecessary check in alloc_dev_dax_range()
device-dax: Fix range release
device-dax: delete a redundancy check in dev_dax_validate_align()
libnvdimm/label: Return -ENXIO for no slot in __blk_label_update
device-dax/core: Fix memory leak when rmmod dax.ko
device-dax/pmem: Convert comma to semicolon
libnvdimm: Cleanup include of badblocks.h
ACPI: NFIT: Fix input validation of bus-family
libnvdimm/namespace: Fix reaping of invalidated block-window-namespace labels
ACPI/nfit: avoid accessing uninitialized memory in acpi_nfit_ctl()
|
|
Pull drm fixes from Dave Airlie:
"Xmas eve pull request present.
Just some fixes that trickled in this past week: Mostly amdgpu fixes,
with a dma-buf/mips build fix and some misc komeda fixes.
dma-buf:
- fix build on mips
komeda:
- fix commit tail operation order
- NULL pointer fix
- out of bounds access fix
ttm:
- remove an unused function
amdgpu:
- Vangogh SMU fixes
- Arcturus gfx9 fixes
- Misc display fixes
- Sienna Cichlid SMU update
- Fix S3 display memory leak
- Fix regression caused by DP sub-connector support
amdkfd:
- Properly require pcie atomics for gfx10"
* tag 'drm-next-2020-12-24' of git://anongit.freedesktop.org/drm/drm: (31 commits)
drm/amd/display: Fix memory leaks in S3 resume
drm/amdgpu: Fix a copy-pasta comment
drm/amdgpu: only set DP subconnector type on DP and eDP connectors
drm/amd/pm: bump Sienna Cichlid smu_driver_if version to match latest pmfw
drm/amd/display: add getter routine to retrieve mpcc mux
drm/amd/display: always program DPPDTO unless not safe to lower
drm/amd/display: [FW Promotion] Release 0.0.47
drm/amd/display: updated wm table for Renoir
drm/amd/display: Acquire DSC during split stream for ODM only if top_pipe
drm/amd/display: Multi-display underflow observed
drm/amd/display: Remove unnecessary NULL check
drm/amd/display: Update RN/VGH active display count workaround
drm/amd/display: change SMU repsonse timeout to 2s.
drm/amd/display: gradually ramp ABM intensity
drm/amd/display: To modify the condition in indicating branch device
drm/amd/display: Modify the hdcp device count check condition
drm/amd/display: Interfaces for hubp blank and soft reset
drm/amd/display: handler not correctly checked at remove_irq_handler
drm/amdgpu: check gfx pipe availability before toggling its interrupts
drm/amdgpu: remove unnecessary asic type check
...
|
|
Pull virtio updates from Michael Tsirkin:
- vdpa sim refactoring
- virtio mem: Big Block Mode support
- misc cleanus, fixes
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (61 commits)
vdpa: Use simpler version of ida allocation
vdpa: Add missing comment for virtqueue count
uapi: virtio_ids: add missing device type IDs from OASIS spec
uapi: virtio_ids.h: consistent indentions
vhost scsi: fix error return code in vhost_scsi_set_endpoint()
virtio_ring: Fix two use after free bugs
virtio_net: Fix error code in probe()
virtio_ring: Cut and paste bugs in vring_create_virtqueue_packed()
tools/virtio: add barrier for aarch64
tools/virtio: add krealloc_array
tools/virtio: include asm/bug.h
vdpa/mlx5: Use write memory barrier after updating CQ index
vdpa: split vdpasim to core and net modules
vdpa_sim: split vdpasim_virtqueue's iov field in out_iov and in_iov
vdpa_sim: make vdpasim->buffer size configurable
vdpa_sim: use kvmalloc to allocate vdpasim->buffer
vdpa_sim: set vringh notify callback
vdpa_sim: add set_config callback in vdpasim_dev_attr
vdpa_sim: add get_config callback in vdpasim_dev_attr
vdpa_sim: make 'config' generic and usable for any device type
...
|
|
Pull in miscellaneous device-dax fixups and cleanups for v5.11.
|
|
Swap the calling sequence of krealloc() and __request_region(), call the
latter first. In this way, the value of dev_dax->nr_range does not need to
be considered when __request_region() failed.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201219081840.1149-2-thunder.leizhen@huawei.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
There are multiple locations that open-code the release of the last
range in a device-dax instance. Consolidate this into a new
dev_dax_trim_range() helper.
This also addresses a kmemleak report:
# cat /sys/kernel/debug/kmemleak
[..]
unreferenced object 0xffff976bd46f6240 (size 64):
comm "ndctl", pid 23556, jiffies 4299514316 (age 5406.733s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 20 c3 37 00 00 00 .......... .7...
ff ff ff 7f 38 00 00 00 00 00 00 00 00 00 00 00 ....8...........
backtrace:
[<00000000064003cf>] __kmalloc_track_caller+0x136/0x379
[<00000000d85e3c52>] krealloc+0x67/0x92
[<00000000d7d3ba8a>] __alloc_dev_dax_range+0x73/0x25c
[<0000000027d58626>] devm_create_dev_dax+0x27d/0x416
[<00000000434abd43>] __dax_pmem_probe+0x1c9/0x1000 [dax_pmem_core]
[<0000000083726c1c>] dax_pmem_probe+0x10/0x1f [dax_pmem]
[<00000000b5f2319c>] nvdimm_bus_probe+0x9d/0x340 [libnvdimm]
[<00000000c055e544>] really_probe+0x230/0x48d
[<000000006cabd38e>] driver_probe_device+0x122/0x13b
[<0000000029c7b95a>] device_driver_attach+0x5b/0x60
[<0000000053e5659b>] bind_store+0xb7/0xc3
[<00000000d3bdaadc>] drv_attr_store+0x27/0x31
[<00000000949069c5>] sysfs_kf_write+0x4a/0x57
[<000000004a8b5adf>] kernfs_fop_write+0x150/0x1e5
[<00000000bded60f0>] __vfs_write+0x1b/0x34
[<00000000b92900f0>] vfs_write+0xd8/0x1d1
Reported-by: Jane Chu <jane.chu@oracle.com>
Cc: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/160834570161.1791850.14911670304441510419.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-next
amd-drm-fixes-5.11-2020-12-23:
amdgpu:
- Vangogh SMU fixes
- Arcturus gfx9 fixes
- Misc display fixes
- Sienna Cichlid SMU update
- Fix S3 display memory leak
- Fix regression caused by DP sub-connector support
amdkfd:
- Properly require pcie atomics for gfx10
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201223204752.4019-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
* dma-buf: Include <linux/vmalloc.h> for building on MIPS
* komeda: Fix order of operation in commit tail; Fix NULL-pointer and
out-of-bounds access; Cleanups
* ttm: Fix an unused-function warning
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/X+JFYlW1SEZa6ShA@linux-uq9g
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- A series from Prashant for Type-C to implement TYPEC_STATUS,
parsing USB PD Partner ID VDOs, and registering partner altmodes.
cros_ec misc:
- Don't treat RTC events as wakeup sources in cros_ec_proto"
* tag 'tag-chrome-platform-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_typec: Tolerate unrecognized mux flags
platform/chrome: cros_ec_typec: Register partner altmodes
platform/chrome: cros_ec_typec: Parse partner PD ID VDOs
platform/chrome: cros_ec_typec: Introduce TYPEC_STATUS
platform/chrome: cros_ec: Import Type C host commands
platform/chrome: cros_ec_typec: Clear partner identity on device removal
platform/chrome: cros_ec_typec: Fix remove partner logic
platform/chrome: cros_ec_typec: Relocate set_port_params_v*() functions
platform/chrome: Don't treat RTC events as wakeup sources
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Removal of the pnx83xx driver
- Add a binding for A100's watchdog controller
- Add Rockchip compatibles to snps,dw-wdt.yaml
- hpwdt: Disable NMI in Crash Kernel
- Fix potential dereferencing of null pointer in watchdog_core
- Several other small fixes and improvements
* tag 'linux-watchdog-5.11-rc1' of git://www.linux-watchdog.org/linux-watchdog: (23 commits)
watchdog: convert comma to semicolon
watchdog: iTCO_wdt: use dev_*() instead of pr_*() for logging
dt-binding: watchdog: add Rockchip compatibles to snps,dw-wdt.yaml
watchdog: coh901327: add COMMON_CLK dependency
dt-bindings: watchdog: sun4i: Add A100 compatible
watchdog: qcom: Avoid context switch in restart handler
watchdog: iTCO_wdt: use module_platform_device() macro
watchdog: Fix potential dereferencing of null pointer
watchdog: wdat_wdt: Fix missing kerneldoc reported by W=1
watchdog/hpwdt: Reflect changes
watchdog/hpwdt: Disable NMI in Crash Kernel
wdt: sp805: add watchdog_stop on reboot
watchdog: sbc_fitpc2_wdt: add __user annotations
watchdog: geodewdt: remove unneeded break
watchdog: rti-wdt: fix reference leak in rti_wdt_probe
watchdog: qcom_wdt: set WDOG_HW_RUNNING bit when appropriate
watchdog: remove pnx83xx driver
watchdog: stm32_iwdg: don't print an error on probe deferral
watchdog: sprd: change to use usleep_range() instead of busy loop
watchdog: sprd: check busy bit before new loading rather than after that
...
|
|
EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in memory leak.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This is not a scsi driver.
Reviewed-by: Nirmoy Das <nirmoy.das@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes a crash in drm_object_property_set_value() because the property
is not set for internal DP ports that connect to a bridge chips
(e.g., DP to VGA or DP to LVDS).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210739
Fixes: 65bf2cf95d3ade ("drm/amdgpu: utilize subconnector property for DP through atombios")
Tested-By: Kris Karas <bugs-a17@moonlit-rail.com>
Cc: Oleg Vasilev <oleg.vasilev@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x
|
|
This can suppress the annoying but unharmful prompts.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
- restore lvtma_pwrseq_delay2 from vbios integrated info table
- restore MVID/NVID after power up.
- Enable timer wake up mask when enable timer interrupt.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
new_crtc_state is already dereferenced earlier in the function
[How]
Remove the check
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Need driver to pass values of backlight ramp start and ramp reduction so
that intensity can be ramped down appropriately.
[How]
Using abm_parameters structure to get these values from driver.
Signed-off-by: Rizvi <syerizvi@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
The sink count change HPD_IRQ will be ignored if the branch device has only
DP DFP.
[how]
To remove the port type restriction.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
Some MST display may not report the internal panel to DEVICE_COUNT,
that makes the check condition always failed.
[how]
To update this condition with the reported device count + 1
(because the immediate repeater's internal panel is possibly
not included in DEVICE_COUNT)
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
handler is supposedly passed in as a function pointer;
however, the entire struct amdgpu_dm_irq_handler_data
gets from the list is used to check match.
[how]
use the interrupt_handler within amdgpu_dm_irq_handler_data
for checking match.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
GUI_IDLE interrupts controlled by CP_INT_CNTL_RING0
are only applicable to me0 pipe0.
For ASICs that have gfx pipe removed, don't toggle
those bits.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The number of crtc should be 0 for ASICs that don't
have display engine. Remove the unnecessary asic type
check then.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
