| Age | Commit message (Collapse) | Author |
|---|
|
In a similar fashion to other control traps, register ACL control traps
with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to layer 2 control traps, register layer 3 control
traps with devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to other traps, register layer 2 control traps with
devlink.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently have an Rx listener function for exception traps that marks
received skbs with 'offload_fwd_mark' and injects them to the kernel's
Rx path. The marking is done because all these exceptions occur during
L3 forwarding, after the packets were potentially flooded at L2.
A subsequent patch will add support for control traps. Packets received
via some of these control traps need different handling:
1. Packets might not need to be marked with 'offload_fwd_mark'. For
example, if packet was trapped before L2 forwarding
2. Packets might not need to be injected to the kernel's Rx path. For
example, sampled packets are reported to user space via the psample
module
Factor out a common Rx listener function that only reports trapped
packets to devlink. Call it from mlxsw_sp_rx_no_mark_listener() and
mlxsw_sp_rx_mark_listener() that will inject the packets to the kernel's
Rx path, without and with the marking, respectively.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register two control traps with devlink. The existing selftest at
tools/testing/selftests/drivers/net/netdevsim/devlink_trap.sh iterates
over all registered traps and checks that the action of non-drop traps
cannot be changed. Up until now only exception traps were tested, now
control traps will be tested as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The layer 3 exceptions are still subject to the same trap policer, so
nothing changes, but user space can choose to assign a different one.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sh5 never became a product and has probably never really worked.
Remove it by recursively deleting all associated Kconfig options
and all corresponding files.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rich Felker <dalias@libc.org>
|
|
When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: Liu Xiang <liuxiang_1999@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The removal of mips_swiotlb_ops exposed a problem in octeon_mgmt Ethernet
driver. mips_swiotlb_ops had an mb() after most of the operations and the
removal of the ops had broken the receive functionality of the driver.
My code inspection has shown no other places except
octeon_mgmt_rx_fill_ring() where an explicit barrier would be obviously
missing. The latter function however has to make sure that "ringing the
bell" doesn't happen before RX ring entry is really written.
The patch has been successfully tested on Octeon II.
Fixes: a999933db9ed ("MIPS: remove mips_swiotlb_ops")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The big change in this release is that Matti Vaittinen has factored
out the linear ranges support into a separate library in lib/ since it
is also useful for at least the power subsystem (and most likely
others too), it helps subsystems which need to map register values
into more useful real world values do so with minimal per-driver code.
- Factoring out of the linear ranges support into a library in lib/
from Matti Vaittinen.
- Trace points for bypass mode.
- Use the consumer name in debugfs to make it easier to understand.
- New drivers for Maxim MAX77826 and MAX8998"
* tag 'regulator-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (23 commits)
regulator: max8998: max8998_set_current_limit() can be static
dt-bindings: regulator: Convert anatop regulator to json-schema
regulator: core: Add regulator bypass trace points
regulator: extract voltage balancing code to the separate function
regulator/mfd: max8998: Document charger regulator
regulator: max8998: Add charger regulator
MAINTAINERS: Add maintainer entry for linear ranges helper
regulator: bd718x7: remove voltage change restriction from BD71847 LDOs
lib: linear_ranges: Add missing MODULE_LICENSE()
regulator: use linear_ranges helper
power: supply: bd70528: rename linear_range to avoid collision
lib/test_linear_ranges: add a test for the 'linear_ranges'
lib: add linear ranges helpers
regulator: db8500-prcmu: Use true,false for bool variable
regulator: bd718x7: remove voltage change restriction from BD71847
regulator: max77826: Remove erroneous additionalProperties
regulator: qcom-rpmh: Fix typos in pm8150 and pm8150l
regulator: Document bindings for max77826
regulator: max77826: Add max77826 regulator driver
regulator: tps80031: remove redundant assignment to variables ret and val
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"This has been a very active release for the DesignWare driver in
particular - after a long period of inactivity we have had a lot of
people actively working on it for unrelated reasons this cycle with
some of that work still not landed.
Otherwise it's been fairly quiet for the subsystem.
Highlights include:
- Lots of performance improvements and fixes for the DesignWare
driver from Serge Semin, Andy Shevchenko, Wan Ahmad Zainie, Clement
Leger, Dinh Nguyen and Jarkko Nikula.
- Support for octal mode transfers in spidev.
- Slave mode support for the Rockchip drivers.
- Support for AMD controllers, Broadcom mspi and Raspberry Pi 4, and
Intel Elkhart Lake"
* tag 'spi-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (125 commits)
spi: spi-fsl-dspi: fix native data copy
spi: Convert DW SPI binding to DT schema
spi: dw: Refactor mid_spi_dma_setup() to separate DMA and IRQ config
spi: dw: Make DMA request line assignments explicit for Intel Medfield
spi: bcm2835: Remove shared interrupt support
dt-bindings: snps,dw-apb-ssi: add optional reset property
spi: dw: add reset control
spi: bcm2835: Enable shared interrupt support
spi: bcm2835: Implement shutdown callback
spi: dw: Use regset32 DebugFS method to create regdump file
spi: dw: Add DMA support to the DW SPI MMIO driver
spi: dw: Cleanup generic DW DMA code namings
spi: dw: Add DW SPI DMA/PCI/MMIO dependency on the DW SPI core
spi: dw: Remove DW DMA code dependency from DW_DMAC_PCI
spi: dw: Move Non-DMA code to the DW PCIe-SPI driver
spi: dw: Add core suffix to the DW APB SSI core source file
spi: dw: Fix Rx-only DMA transfers
spi: dw: Use DMA max burst to set the request thresholds
spi: dw: Parameterize the DMA Rx/Tx burst length
spi: dw: Add SPI Rx-done wait method to DMA-based transfer
...
|
|
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register ndo callback via flow_indr_dev_register() and
flow_indr_dev_unregister().
No need for mlx5e_rep_indr_clean_block_privs() since flow_block_cb_free()
already releases the internal mapping via ->release callback, which in
this case is mlx5e_rep_indr_tc_block_unbind().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a very active release for the regmap API for some
reason, a lot of it due to new devices with odd requirements that can
sensibly be handled here.
- Add support for buses implementing a custom reg_update_bits()
method in case the bus has a native operation for this.
- Support 16 bit register addresses in SMBus.
- Allow customization of the device attached to regmap-irq.
- Helpers for bitfield operations and per-port field initializations"
* tag 'regmap-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: provide helpers for simple bit operations
regmap: add helper for per-port regfield initialization
regmap-i2c: add 16-bit width registers support
regmap: Simplify implementation of the regmap_field_read_poll_timeout() macro
regmap: Simplify implementation of the regmap_read_poll_timeout() macro
regmap: add reg_sequence helpers
regmap-irq: make it possible to add irq_chip do a specific device node
regmap: Add bus reg_update_bits() support
regmap: debugfs: check count when read regmap file
|
|
Shrink the code visually by replacing regmap_update_bits() with
appropriate regmap bit operations where applicable.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In many instances regmap_update_bits() is used for simple bit setting
and clearing. In these cases the last argument is redundant and we can
hide it with a static inline function.
This adds three new helpers for simple bit operations: set_bits,
clear_bits and test_bits (the last one defined as a regular function).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
"Infrastructure:
- Add notification support
New drivers:
- Baikal-T1 PVT sensor driver
- amd_energy driver to report energy counters
- Driver for Maxim MAX16601
- Gateworks System Controller
Various:
- applesmc: avoid overlong udelay()
- dell-smm: Use one DMI match for all XPS models
- ina2xx: Implement alert functions
- lm70: Add support for ACPI
- lm75: Fix coding-style warnings
- lm90: Add max6654 support to lm90 driver
- nct7802: Replace container_of() API
- nct7904: Set default timeout
- nct7904: Add watchdog function
- pmbus: Improve initialization of 'currpage' and 'currphase'"
* tag 'hwmon-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (24 commits)
hwmon: Add Baikal-T1 PVT sensor driver
hwmon: Add notification support
dt-bindings: hwmon: Add Baikal-T1 PVT sensor binding
hwmon: (applesmc) avoid overlong udelay()
hwmon: (nct7904) Set default timeout
hwmon: (amd_energy) Missing platform_driver_unregister() on error in amd_energy_init()
MAINTAINERS: add entry for AMD energy driver
hwmon: (amd_energy) Add documentation
hwmon: Add amd_energy driver to report energy counters
hwmon: (nct7802) Replace container_of() API
hwmon: (lm90) Add max6654 support to lm90 driver
hwmon : (nct6775) Use kobj_to_dev() API
hwmon: (pmbus) Driver for Maxim MAX16601
hwmon: (pmbus) Improve initialization of 'currpage' and 'currphase'
hwmon: (adt7411) update contact email
hwmon: (lm75) Fix all coding-style warnings on lm75 driver
hwmon: Reduce indentation level in __hwmon_device_register()
hwmon: (ina2xx) Implement alert functions
hwmon: (lm70) Add support for ACPI
hwmon: (dell-smm) Use one DMI match for all XPS models
...
|
|
The caller doesn't care about the error codes, they only check for zero
vs non-zero. Still, it's better to preserve the negative error codes
from alloc_uld_rxqs() instead of changing it to 1. We can also return
directly if there is a failure.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull tpm updates from Jarkko Sakkinen.
* tag 'tpmdd-next-20200522' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: eventlog: Replace zero-length array with flexible-array member
tpm/tpm_ftpm_tee: Use UUID API for exporting the UUID
|
|
When proxy mode is enabled the vxlan device might reply to Neighbor
Solicitation (NS) messages on behalf of remote hosts.
In case the NS message includes the "Source link-layer address" option
[1], the vxlan device will use the specified address as the link-layer
destination address in its reply.
To avoid an infinite loop, break out of the options parsing loop when
encountering an option with length zero and disregard the NS message.
This is consistent with the IPv6 ndisc code and RFC 4886 which states
that "Nodes MUST silently discard an ND packet that contains an option
with length zero" [2].
[1] https://tools.ietf.org/html/rfc4861#section-4.3
[2] https://tools.ietf.org/html/rfc4861#section-4.6
Fixes: 4b29dba9c085 ("vxlan: fix nonfunctional neigh_reduce()")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2020-06-01
Here's one last bluetooth-next pull request for 5.8, which I hope can
still be accepted.
- Enabled Wide-Band Speech (WBS) support for Qualcomm wcn3991
- Multiple fixes/imprvovements to Qualcomm-based devices
- Fix GAP/SEC/SEM/BI-10-C qualfication test case
- Added support for Broadcom BCM4350C5 device
- Several other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
SPI NOR core changes:
- add, update support and fix few flashes
- prepare BFPT parsing for JESD216 rev D
- kernel doc fixes
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
|
|
Print IRQ number used by DPC port, like AER/PME does. It provides
convenience to track DPC interrupts counts of certain port from
/proc/interrupts.
Link: https://lore.kernel.org/r/1589018214-52752-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Previously we used "pos" or "aer_pos" for the offset of the AER Capability.
Use "aer" consistently and initialize it the same way everywhere. No
functional change intended.
Link: https://lore.kernel.org/r/20200529230915.GA479883@bjorn-Precision-5520
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
|
|
pcie_aer_get_firmware_first() checks dev->aer_cap, so we can remove
redundant dev->aer_cap checks in the callers.
Link: https://lore.kernel.org/r/d5ccc7a060ec9cdc234bdae7df8a0a4410f13f42.1590534843.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
AER is a PCIe Extended Capability, so dev->aer_cap will only be set for
PCIe devices. Remove redundant pci_is_pcie() checks.
Link: https://lore.kernel.org/r/361c622eabe5b845b8092e0bec04a3a2c262cb38.1590534843.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Commit c100beb9ccfb ("PCI/AER: Use only _OSC to determine AER ownership")
removed the use of HEST in determining AER ownership, but the AER driver
still used HEST to verify AER ownership in some of its APIs.
Per the ACPI spec v6.3, sec 18.3.2.4, some HEST table entries contain a
FIRMWARE_FIRST bit, but that bit does not tell us anything about ownership
of the AER capability.
Remove parsing of HEST to look for FIRMWARE_FIRST.
Add pcie_aer_is_native() for the places that need to know whether the OS
owns the AER capability.
[bhelgaas: commit log, reorder patch, remove unused __aer_firmware_first]
Link: https://lore.kernel.org/r/9a37f53a4e6ff4942ff8e18dbb20b00e16c47341.1590534843.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull ARM cpufreq updates for v5.8-rc1 (part 2) from Viresh Kumar:
"This contains a single patch to enable CPUFREQ_NEED_INITIAL_FREQ_CHECK
flag for tegra driver."
* 'cpufreq/arm/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: tegra186: add CPUFREQ_NEED_INITIAL_FREQ_CHECK flag
|
|
* acpi-apei:
arm64: acpi: Make apei_claim_sea() synchronise with APEI's irq work
ACPI: APEI: Kick the memory_failure() queue for synchronous errors
mm/memory-failure: Add memory_failure_queue_kick()
* acpi-pmic:
ACPI / PMIC: Add i2c address for thermal control
* acpi-video:
ACPI: video: Use native backlight on Acer TravelMate 5735Z
* acpi-dptf:
ACPI: DPTF: Add battery participant driver
ACPI: DPTF: Additional sysfs attributes for power participant driver
|
|
'acpi-pci'
* acpi-processor:
ACPI: processor: idle: Allow probing on platforms with one ACPI C-state
* acpi-cppc:
ACPI: CPPC: Fix reference count leak in acpi_cppc_processor_probe()
ACPI: CPPC: Make some symbols static
* acpi-dbg:
ACPI: debug: Make two functions static
* acpi-misc:
ACPI: GED: use correct trigger type field in _Exx / _Lxx handling
ACPI: GED: add support for _Exx / _Lxx handler methods
ACPI: Delete unused proc filename macros
* acpi-pci:
ACPI: hotplug: PCI: Use the new acpi_evaluate_reg() helper
ACPI: utils: Add acpi_evaluate_reg() helper
|
|
* acpica:
ACPICA: Update version to 20200430
ACPICA: Fix required parameters for _NIG and _NIH
ACPICA: Dispatcher: add status checks
ACPICA: Disassembler: ignore AE_ALREADY_EXISTS status when parsing create operators
ACPICA: Move acpi_gbl_next_cmd_num definition to acglobal.h
ACPICA: Make acpi_protocol_lengths static
* acpi-tables:
ACPI: sleep: Put the FACS table after using it
ACPI: scan: Put SPCR and STAO table after using it
ACPI: EC: Put the ACPI table after using it
ACPI: APEI: Put the HEST table for error path
ACPI: APEI: Put the error record serialization table for error path
ACPI: APEI: Put the error injection table for error path and module exit
ACPI: APEI: Put the boot error record table after parsing
ACPI: watchdog: Put the watchdog action table after parsing
ACPI: LPIT: Put the low power idle table after using it
|
|
* pm-devfreq:
PM / devfreq: Use lockdep asserts instead of manual checks for locked mutex
PM / devfreq: imx-bus: Fix inconsistent IS_ERR and PTR_ERR
PM / devfreq: Replace strncpy with strscpy
PM / devfreq: imx: Register interconnect device
PM / devfreq: Add generic imx bus scaling driver
PM / devfreq: tegra30: Delete an error message in tegra_devfreq_probe()
PM / devfreq: tegra30: Make CPUFreq notifier to take into account boosting
* powercap:
powercap: RAPL: remove unused local MSR define
powercap/intel_rapl: add support for ElkhartLake
* pm-docs:
Documentation: admin-guide: pm: Document intel-speed-select
* pm-tools:
cpupower: Remove unneeded semicolon
|
|
* pm-cpufreq:
cpufreq: Fix up cpufreq_boost_set_sw()
cpufreq: fix minor typo in struct cpufreq_driver doc comment
cpufreq: qoriq: Add platform dependencies
clk: qoriq: add cpufreq platform device
cpufreq: qoriq: convert to a platform driver
cpufreq: qcom: fix wrong compatible binding
cpufreq: imx-cpufreq-dt: support i.MX7ULP
cpufreq: dt: Add support for r8a7742
cpufreq: Add i.MX7ULP to cpufreq-dt-platdev blacklist
cpufreq: omap: Build driver by default for ARCH_OMAP2PLUS
cpufreq: intel_pstate: Use passive mode by default without HWP
|
|
* pm-cpuidle:
cpuidle: Fix three reference count leaks
cpuidle: Convert Qualcomm SPM driver to a generic CPUidle driver
Documentation: ABI: make current_governer_ro as a candidate for removal
Documentation: cpuidle: update the document
cpuidle: sysfs: Remove sysfs_switch and switch attributes
cpuidle: Make cpuidle governor switchable to be the default behaviour
cpuidle: sysfs: Accept governor name with 15 characters
cpuidle: sysfs: Fix the overlap for showing available governors
cpuidle: psci: Fixup execution order when entering a domain idle state
cpuidle: sysfs: Minor coding style corrections
cpuidle: sysfs: Remove the unused define_one_r(o/w) macros
|
|
* pm-core:
PM: runtime: Replace pm_runtime_callbacks_present()
PM: runtime: clk: Fix clk_pm_runtime_get() error path
PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()
* pm-sleep:
PM: hibernate: Restrict writes to the resume device
PM: hibernate: Split off snapshot dev option
PM: hibernate: Incorporate concurrency handling
PM: sleep: Helpful edits for devices.rst documentation
Documentation: PM: sleep: Update driver flags documentation
PM: sleep: core: Rename DPM_FLAG_LEAVE_SUSPENDED
PM: sleep: core: Rename DPM_FLAG_NEVER_SKIP
PM: sleep: core: Rename dev_pm_smart_suspend_and_suspended()
PM: sleep: core: Rename dev_pm_may_skip_resume()
PM: sleep: core: Rework the power.may_skip_resume handling
PM: sleep: core: Do not skip callbacks in the resume phase
PM: sleep: core: Fold functions into their callers
PM: sleep: core: Simplify the SMART_SUSPEND flag handling
|
|
With the advent of preempt-to-busy, a request may still be on the GPU as
we unwind. And in the case of a unpreemptible [due to HW] request, that
request will remain indefinitely on the GPU even though we have
returned it back to our submission queue, and cleared the active bit.
We only run the execution callbacks on transferring the request from our
submission queue to the execution queue, but if this is a bonded request
that the HW is waiting for, we will not submit it (as we wait for a
fresh execution) even though it is still being executed.
As we know that there are always preemption points between requests, we
know that only the currently executing request may be still active even
though we have cleared the flag. However, we do not precisely know which
request is in ELSP[0] due to a delay in processing events, and
furthermore we only store the last request in a context in our state
tracker.
Fixes: 22b7a426bbe1 ("drm/i915/execlists: Preempt-to-busy")
Testcase: igt/gem_exec_balancer/bonded-dual
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200529143926.3245-1-chris@chris-wilson.co.uk
(cherry picked from commit b55230e5e800868961fc271b26d9ce53ae1f691e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
When we push a virtual request onto the HW, we update the rq->engine to
point to the physical engine. A request that is then submitted by the
user that waits upon the virtual engine, but along the physical engine
in use, will then see that it is due to be submitted to the same engine
and take a shortcut (and be queued without waiting for the completion
fence). However, the virtual request may be preempted (either by higher
priority users, or by timeslicing) and removed from the physical engine
to be migrated over to one of its siblings. The dependent normal request
however is oblivious to the removal of the virtual request and remains
queued to execute on HW, believing that once it reaches the head of its
queue all of its predecessors will have completed executing!
v2: Beware restriction of signal->execution_mask prior to submission.
Fixes: 6d06779e8672 ("drm/i915: Load balancing across a virtual engine")
Testcase: igt/gem_exec_balancer/sliced
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: <stable@vger.kernel.org> # v5.3+
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526090753.11329-2-chris@chris-wilson.co.uk
(cherry picked from commit 511b6d9aed417739b6aa49d0b6b4354ad21020f1)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Reorder the code so that we can reuse the await_execution from a special
case in await_request in the next patch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200526090753.11329-1-chris@chris-wilson.co.uk
(cherry picked from commit ffb0c600c240103f6f34e07892a7e0a75502b243)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
|
|
|
|
|
|
Fixes: 4ffea5e083f8 ("regulator: max8998: Add charger regulator")
Signed-off-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200530130314.GA73557@d7d8dbfb64ff
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) framework changes for v5.8
from Viresh Kumar:
"This contains:
- support for interconnect bandwidth in the OPP core (Georgi Djakov,
Saravana Kannan, Sibi Sankar, Viresh Kumar).
- support for regulator enable/disable (Kamil Konieczny).
This is based on three patches from the interconnect tree which
shall get merged via Greg's tree."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: Don't parse icc paths unnecessarily
opp: Remove bandwidth votes when target_freq is zero
opp: core: add regulators enable and disable
opp: Reorder the code for !target_freq case
opp: Expose bandwidth information via debugfs
cpufreq: dt: Add support for interconnect bandwidth scaling
opp: Update the bandwidth on OPP frequency changes
opp: Add sanity checks in _read_opp_key()
opp: Add support for parsing interconnect bandwidth
interconnect: Remove unused module exit code from core
interconnect: Disallow interconnect core to be built as a module
interconnect: Add of_icc_get_by_index() helper function
OPP: Add helpers for reading the binding properties
dt-bindings: opp: Introduce opp-peak-kBps and opp-avg-kBps bindings
|
|
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Add support for a new method for BIOS to provide the address and length
of the protected SMI communication buffer, via SMBIOS OEM strings.
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
On the ASUS laptop UX325JA/UX425JA, most of the media keys are not
working due to the ASUS WMI driver fails to be loaded. The ACPI error
as follows leads to the failure of asus_wmi_evaluate_method.
ACPI BIOS Error (bug): AE_AML_BUFFER_LIMIT, Field [IIA3] at bit offset/length 96/32 exceeds size of target Buffer (96 bits) (20200326/dsopcode-203)
No Local Variables are initialized for Method [WMNB]
ACPI Error: Aborting method \_SB.ATKD.WMNB due to previous error (AE_AML_BUFFER_LIMIT) (20200326/psparse-531)
The DSDT for the WMNB part shows that 5 DWORD required for local
variables and the 3rd variable IIA3 hit the buffer limit.
Method (WMNB, 3, Serialized)
{ ..
CreateDWordField (Arg2, Zero, IIA0)
CreateDWordField (Arg2, 0x04, IIA1)
CreateDWordField (Arg2, 0x08, IIA2)
CreateDWordField (Arg2, 0x0C, IIA3)
CreateDWordField (Arg2, 0x10, IIA4)
Local0 = (Arg1 & 0xFFFFFFFF)
If ((Local0 == 0x54494E49))
..
}
The limitation is determined by the input acpi_buffer size passed
to the wmi_evaluate_method. Since the struct bios_args is the data
structure used as input buffer by default for all ASUS WMI calls,
the size needs to be expanded to fix the problem.
Signed-off-by: Chris Chiu <chiu@endlessm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
