| Age | Commit message (Collapse) | Author |
|---|
|
Add _REG postfix to register addresses to avoid confusion with
fields. Also add additional field defines and use throughout the
driver in place of magic numbers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-14-jic23@kernel.org
|
|
Note this doesn't support everything the chip can do as we ignore
window mode for now (in window / out of window).
* Given the chip doesn't have any way of disabling the threshold
pins, use disable_irq() etc to mask them except when we actually
want them enabled (previously events were always enabled).
Note there are race conditions, but using the current state from
the status register and disabling interrupts across changes in
type of event should mean those races result in interrupts,
but no events to userspace.
* Correctly reflect that there is one threshold line per channel.
* Only take notice of rising edge. If anyone wants the other edge
then they should set the other threshold (they are available for
rising and falling directions). This isn't perfect but it makes
it a lot simpler.
* If insufficient interrupts are specified in firnware, don't support
events.
* Adaptive events use the same pos/neg values of thrMD as non adaptive
ones.
Tested against qemu based emulation.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20210314181511.531414-13-jic23@kernel.org
|
|
Now we have core support for timeouts related to adaptive events, let us
use it. Note the units of that attribute are seconds, so we also need
to scale the cycles value by the period of each sample.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-12-jic23@kernel.org
|
|
For adaptive threshold events, the current value is compared with a
(typically) low pass filtered version of the same signal that slowly
tracks large scale changes. However, sometimes a step change can
result in a large lag before the low pass filtered version begins
to track the signal again. Timeouts can be used to made an
instantaneous 'correction'. Documentation of this attribute
is added in a later patch.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-11-jic23@kernel.org
|
|
Device uses a fixed sampling frequency. Let us expose it to userspace.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-10-jic23@kernel.org
|
|
Also
* drop i2c_set_client_data() as now unused.
* white space cleanups
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-9-jic23@kernel.org
|
|
The event line is active high and not maskable within the device.
It indicates current state directly.
The device supports separate rising and falling thresholds so rather
than trying to using each bound to detect in both directions just use
IRQF_TRIGGER_RISING. If a user wants to detect the value falling
back below the threshold, then set the falling threshold appropriately.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-8-jic23@kernel.org
|
|
present or not
The driver supports devices with different numbers of channels and
also can function without provision of an IRQ (with reduced features),
so this patch handles this cleanly by having multiple chan_spec
arrays and iio_info structures to pick between depending on what we
have.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-7-jic23@kernel.org
|
|
There are no mainline board files using this driver so lets drop
the platform_data support in favour of devicetree and similar.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-6-jic23@kernel.org
|
|
updating
The timeout is treated as one single value, but the datasheet describes
it as two 4 bit values, one for each direction of event.
As such change the driver to support the separate directions.
Also add limit checking to ensure it fits within the 4 bits.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-5-jic23@kernel.org
|
|
Original code was ordered in a fairly unituitive fashion with
the non adaptive threshold handling returning from the switch
statement, whilst the adapative path did the actual writes outside
the switch. Make it more readable by bringing everything within
the switch statement cases and reducing scope of local variables
as appropriate.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-4-jic23@kernel.org
|
|
The devices support window detection, but that corresponds to
being outside of a range defined by a lower an uppper bound rather
than being related to magnitude as such. Hence drop this interface
in the interests of making the driver ABI compliant.
We may bring back support for the window mode at somepoint in the future
but it will be in an ABI compliant fashion.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20210314181511.531414-3-jic23@kernel.org
|
|
Reduces boilerplate and chances of getting the error handling wrong.
No functional change.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Barry Song <song.bao.hua@hisilicon>
Link: https://lore.kernel.org/r/20210314181511.531414-2-jic23@kernel.org
|
|
The inv_mpu6050 driver requires an interrupt for buffered capture. But non
buffered reading for measurements works just fine without an interrupt
connected.
Make the interrupt optional to support this case.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210325131046.13383-2-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The inv_mpu6050 driver manually assigns the indio_dev->modes property. But
this is not necessary since it will be setup in iio_trigger_buffer_setup().
Remove the manual assignment.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Link: https://lore.kernel.org/r/20210325131046.13383-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
As Lars pointed out, we could either return the FD vs memcpy-ing it to the
userspace data object.
However, this comment exposed a bug. We should return 0 or negative from
these ioctl() handlers. Because an ioctl() handler can also return
IIO_IOCTL_UNHANDLED (which is positive 1), which means that the ioctl()
handler doesn't support this ioctl number. Positive 1 could also be a valid
FD number in some corner cases.
The reason we did this is to be able to differentiate between an error
code and an unsupported ioctl number; for unsupported ioctl numbers, the
main loop should keep going.
Maybe we should change this to a higher negative number, to avoid such
cases when/if we add more ioctl() handlers.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Fixes: f73f7f4da5818 ("iio: buffer: add ioctl() to support opening extra buffers for IIO device")
Signed-off-by: Alexandru Ardelean <aardelean@deviqon.com>
Link: https://lore.kernel.org/r/20210322084135.17536-1-aardelean@deviqon.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The code was checking if (ret) from the processed
channel readout, not smart, we need to check if (ret < 0)
as this will likely be something like IIO_VAL_INT.
Fixes: 635ef601b238 ("iio: Provide iio_read_channel_processed_scale() API")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210323122705.1326362-1-linus.walleij@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The __mhi_unprepare_channel() API does not require the __ prefix.
Get rid of it and make the internal function consistent with the
other function names.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Link: https://lore.kernel.org/r/1617311778-1254-9-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
A client can attempt to unprepare certain channels for transfer even
after the execution environment they are supposed to run in has changed.
In the event that happens, the device need not be notified of the reset
and the host can proceed with clean up for the channel context and
memory allocated for it on the host as the device will no longer be able
to respond to such a request.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-8-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
When clearing up the channel context after client drivers are
done using channels, the configuration is currently not being
reset entirely. Ensure this is done to appropriately handle
issues where clients unaware of the context state end up calling
functions which expect a context.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-7-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
MHI host can fail early if device is in a bad state by attempting
to assert device wake and holding the runtime PM vote before
sending a channel update command instead of performing a wake
toggle and waiting for a timeout if the send were to fail. This
can help improve the design and enable shorter wait periods for
device to respond as votes are already held.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-6-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Debug messages dealing with client devices use the generic MHI
controller or parent device along with a channel number. It would
be better to instead use the client device directly and enable
better log messages for channel updates.
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-5-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Improve the channel handling state machine such that all commands
go through a common function and a validation process to ensure
that the state machine is not violated in any way and adheres to
the MHI specification. Using this common function allows MHI to
eliminate some unnecessary debug messages and code duplication.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-4-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
If a channel was explicitly stopped but not reset and a driver
remove is issued, clean up the channel context such that it is
reflected on the device. This move is useful if a client driver
module is unloaded or a device crash occurs with the host having
placed the channel in a stopped state.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-3-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add support to allow sending the STOP channel command. If a
client driver would like to STOP a channel and have the device
retain the channel context instead of issuing a RESET to it and
clearing the context, this would provide support for it after
the ability to send this command is exposed to clients.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617311778-1254-2-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Add generic info for SDX65 based modems.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1617399199-35172-1-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Some controllers can choose to skip preparation for power up.
In that case, device context is initialized based on the pre_init
flag not being set during mhi_prepare_for_power_up(). There is no
reason MHI host driver should maintain and provide controllers
with two separate paths for preparing MHI.
Going forward, all controllers will be required to call the
mhi_prepare_for_power_up() API followed by their choice of sync
or async power up. This allows MHI host driver to get rid of the
pre_init flag and sets up a common way for all controllers to use
MHI. This also helps controllers fail early on during preparation
phase in some failure cases.
Signed-off-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Hemant Kumar <hemantk@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617313309-24035-1-git-send-email-bbhatt@codeaurora.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Since M3 can be entered/exited quite a lot when used for runtime PM,
keep the mhi suspend/resume transitions quiet.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Bhaumik Bhatt <bbhatt@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617700315-12492-2-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
This change ensures that PM reference is always get during packet
queueing and released either after queuing completion (RX) or once
the buffer has been consumed (TX). This guarantees proper update for
underlying MHI controller runtime status (e.g. last_busy timestamp)
and prevents suspend to be triggered while TX packets are flying,
or before we completed update of the RX ring.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1617700315-12492-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
Memory allocated by kvzalloc() should be freed by kvfree().
Fixes: 34ca65352ddf2 ("net/mlx5: E-Switch, Indirect table infrastructur")
Signed-off-by: Xiaoming Ni <nixiaoming@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Make sure to modify uplink port to follow only if the uplink_follow
capability is set as required by the HW spec. Failure to do so causes
traffic to the uplink representor net device to cease after switching to
switchdev mode.
Fixes: 7d0314b11cdd ("net/mlx5e: Modify uplink state on interface up/down")
Signed-off-by: Eli Cohen <elic@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When changing type with TUNSETLINK ioctl command, set tun->dev->addr_len
to match the appropriate type, using new tun_get_addr_len utility function
which returns appropriate address length for given type. Fixes a
KMSAN-found uninit-value bug reported by syzbot at:
https://syzkaller.appspot.com/bug?id=0766d38c656abeace60621896d705743aeefed51
Reported-by: syzbot+001516d86dbe88862cec@syzkaller.appspotmail.com
Diagnosed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the VF down state bit is cleared after VF sending
link status request command. There is problem that when VF gets
link status replied from PF, the down state bit may still set
as 1. In this case, the link status replied from PF will be
ignored and always set VF link status to down.
To fix this problem, clear VF down state bit before VF requests
link status.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2021-04-06
this is a pull request of 1 patch for net/master.
The patch is by me and fixes the SPI half duplex support in the
mcp251x CAN driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pci_resource_start() is not a good indicator to determine if a PCI
resource exists or not, since the resource may start at address 0.
This is seen when trying to instantiate the driver in qemu for riscv32
or riscv64.
pci 0000:00:01.0: reg 0x10: [io 0x0000-0x001f]
pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000001f]
...
pcnet32: card has no PCI IO resources, aborting
Use pci_resouce_len() instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xuan Zhuo reported that commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") brought a ~10% performance drop.
The reason for the performance drop was that GRO was forced
to chain sk_buff (using skb_shinfo(skb)->frag_list), which
uses more memory but also cause packet consumers to go over
a lot of overhead handling all the tiny skbs.
It turns out that virtio_net page_to_skb() has a wrong strategy :
It allocates skbs with GOOD_COPY_LEN (128) bytes in skb->head, then
copies 128 bytes from the page, before feeding the packet to GRO stack.
This was suboptimal before commit 3226b158e67c ("net: avoid 32 x truesize
under-estimation for tiny skbs") because GRO was using 2 frags per MSS,
meaning we were not packing MSS with 100% efficiency.
Fix is to pull only the ethernet header in page_to_skb()
Then, we change virtio_net_hdr_to_skb() to pull the missing
headers, instead of assuming they were already pulled by callers.
This fixes the performance regression, but could also allow virtio_net
to accept packets with more than 128bytes of headers.
Many thanks to Xuan Zhuo for his report, and his tests/help.
Fixes: 3226b158e67c ("net: avoid 32 x truesize under-estimation for tiny skbs")
Reported-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Link: https://www.spinics.net/lists/netdev/msg731397.html
Co-Developed-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bcm4908_enet_dma_alloc, if callee bcm4908_dma_alloc_buf_descs() failed,
it will free the ring->cpu_addr by dma_free_coherent() and return error.
Then bcm4908_enet_dma_free() will be called, and free the same cpu_addr
by dma_free_coherent() again.
My patch set ring->cpu_addr to NULL after it is freed in
bcm4908_dma_alloc_buf_descs() to avoid the double free.
Fixes: 4feffeadbcb2e ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The top comment is not a kerneldoc, as W=1 build reports:
drivers/i2c/busses/i2c-exynos5.c:39: warning:
expecting prototype for i2c(). Prototype was for HSI2C_CTL() instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
during suspend
Some devices send (duplicate) tablet-mode events when moved around even
though the mode has not changed; and they do this even when suspended.
Change the tablet-mode event handling when priv->wakeup_mode is set to
update the switch state in case it changed and then return immediately
(without calling pm_wakeup_hard_event()) to avoid spurious wakeups.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212537
Fixes: 537b0dd4729e ("platform/x86: intel-hid: Add support for SW_TABLET_MODE")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Elia Devito <eliadevito@gmail.com>
Link: https://lore.kernel.org/r/20210404143831.25173-1-hdegoede@redhat.com
|
|
Typically the mem_commands[] array is in sync with 'enum { CXL_CMDS }'.
Current code works well.
However, the array size of mem_commands[] may not strictly be the same
as CXL_MEM_COMMAND_ID_MAX. E.g. if a new CXL_CMD() is added that is
guarded by #ifdefs, the array could be shorter. This could lead then
further to an out-of-bounds array access in cxl_validate_cmd_from_user().
Fix this by forcing the array size to CXL_MEM_COMMAND_ID_MAX. This
also adds range checks for array items in mem_commands[] at compile
time.
Signed-off-by: Robert Richter <rrichter@amd.com>
Link: https://lore.kernel.org/r/20210324141635.22335-1-rrichter@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
There is no power management of cxl virtual devices, disable
device-power-management and runtime-power-management to prevent
userspace from growing expectations of those attributes appearing. They
can be added back in the future if needed.
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Link: https://lore.kernel.org/r/161728761025.2474381.808344500111924819.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
While device_add() will happen to catch dev_set_name() failures it is a
broken pattern to follow given that the core may try to fall back to a
different name.
Add explicit checking for dev_set_name() failures to be cleaned up by
put_device(). Skip cdev_device_add() and proceed directly to
put_device() if the name set fails.
This type of bug is easier to see if 'alloc' is split from 'add'
operations that require put_device() on failure. So cxl_memdev_alloc()
is split out as a result.
Fixes: b39cb1052a5c ("cxl/mem: Register CXL memX devices")
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/161728760514.2474381.1163928273337158134.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The percpu_ref to gate whether cxl_memdev_ioctl() is free to use the
driver context (@cxlm) to issue I/O is overkill, implemented incorrectly
(missing a device reference before accessing the percpu_ref), and the
complexities of shutting down a percpu_ref contributed to a bug in the
error unwind in cxl_mem_add_memdev() (missing put_device() to be fixed
separately).
Use an rwsem to explicitly synchronize the usage of cxlmd->cxlm, and add
the missing reference counting for cxlmd in cxl_memdev_open() and
cxl_memdev_release_file().
Fixes: b39cb1052a5c ("cxl/mem: Register CXL memX devices")
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/161728759948.2474381.17481500816783671817.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
While none the CXL sysfs attributes are threatening to overrun a
PAGE_SIZE of output, it is good form to use the recommended helpers.
Fixes: b39cb1052a5c ("cxl/mem: Register CXL memX devices")
Reported-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/161728759424.2474381.11231441014951343463.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
during suspend
Some devices send (duplicate) tablet-mode events when moved around even
though the mode has not changed; and they do this even when suspended.
Change the tablet-mode event handling when priv->wakeup_mode is set to
update the switch state in case it changed and then return immediately
(without calling pm_wakeup_hard_event()) to avoid spurious wakeups.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=212537
Fixes: 537b0dd4729e ("platform/x86: intel-hid: Add support for SW_TABLET_MODE")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Elia Devito <eliadevito@gmail.com>
Link: https://lore.kernel.org/r/20210404143831.25173-1-hdegoede@redhat.com
|
|
Disable TE for Droid 4 panel, since implementation is currently
broken. Also disable it for N950 panel, which is untested.
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: 4c1b935fea54 ("drm/omap: dsi: move TE GPIO handling into core")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210227214542.99961-1-sebastian.reichel@collabora.com
|
|
Remove extra blank lines after an open brace to adhere to Linux kernel
coding style.
Reported by checkpatch.
Signed-off-by: Zhansaya Bagdauletkyzy <zhansayabagdaulet@gmail.com>
Link: https://lore.kernel.org/r/f61f6d330bc3fa53d4d420754d1d461b6cfcb2de.1617708653.git.zhansayabagdaulet@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace NULL comparisons with boolean negation to be more consistent with
the rest of the Linux kernel code base.
Reported by checkpatch.
Signed-off-by: Zhansaya Bagdauletkyzy <zhansayabagdaulet@gmail.com>
Link: https://lore.kernel.org/r/74471865b399584d73a18696d2008006301dfd71.1617708653.git.zhansayabagdaulet@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Clean up checks of "Alignment should match open parenthesis"
in file mlme_osdep.h
Signed-off-by: Beatriz Martins de Carvalho <martinsdecarvalhobeatriz@gmail.com>
Link: https://lore.kernel.org/r/20210406105124.78498-1-martinsdecarvalhobeatriz@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove extra spaces after a cast to conform with Linux kernel coding
style.
Reported by checkpatch.
Signed-off-by: Zhansaya Bagdauletkyzy <zhansayabagdaulet@gmail.com>
Link: https://lore.kernel.org/r/f8932bfa35eb7480b69a9c8296bb10fac5a28540.1617697237.git.zhansayabagdaulet@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
