| Age | Commit message (Collapse) | Author |
|---|
|
In mvneta_port_up() we enable relevant RX and TX port queues by write
queues bit map to an appropriate register.
q_map must be ZERO in the beginning of this process.
Signed-off-by: Yelena Krivosheev <yelena@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Miguel reported an skb use after free / double free in vrf_finish_output
when neigh_output returns an error. The vrf driver should return after
the call to neigh_output as it takes over the skb on error path as well.
Patch is a simplified version of Miguel's patch which was written for 4.9,
and updated to top of tree.
Fixes: 8f58336d3f78a ("net: Add ethernet header for pass through VRF device")
Signed-off-by: Miguel Fadon Perlines <mfadon@teldat.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit has fix for RX traffic issues when we stress test the driver
with continuous ifconfig up/down under very high traffic conditions.
Reason for the issue is that, in existing liquidio_stop function NAPI is
disabled even before actual FW/HW interface is brought down via
send_rx_ctrl_cmd(lio, 0). Between time frame of NAPI disable and actual
interface down in firmware, firmware continuously enqueues rx traffic to
host. When interrupt happens for new packets, host irq handler fails in
scheduling NAPI as the NAPI is already disabled.
After "ifconfig <iface> up", Host re-enables NAPI but cannot schedule it
until it receives another Rx interrupt. Host never receives Rx interrupt as
it never cleared the Rx interrupt it received during interface down
operation. NIC Rx interrupt gets cleared only when Host processes queue and
clears the queue counts. Above anomaly leads to other issues like packet
overflow in FW/HW queues, backpressure.
Fix:
This commit fixes this issue by disabling NAPI only after informing
firmware to stop queueing packets to host via send_rx_ctrl_cmd(lio, 0).
send_rx_ctrl_cmd is not visible in the patch as it is already there in the
code. The DOWN command also waits for any pending packets to be processed
by NAPI so that the deadlock will not occur.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A simple but worthwhile I2C driver fix for 4.16"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-stm32f7: fix no check on returned setup
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan-next
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2018-03-29
An update from ieee802154 for *net-next*
Colin fixed a unused variable in the new mcr20a driver.
Harry fixed an unitialised data read in the debugfs interface of the
ca8210 driver.
If there are any issues or you think these are to late for -rc1 (both can also
go into -rc2 as they are simple fixes) let me know.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds initial suport for DWMAC5 and implements the Automotive Safety
Package which is available from core version 5.10.
The Automotive Safety Pacakge (also called Safety Features) offers us
with error protection in the core by implementing ECC Protection in
memories, on-chip data path parity protection, FSM parity and timeout
protection and Application/CSR interface timeout protection.
In case of an uncorrectable error we call stmmac_global_err() and
reconfigure the whole core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently TX Timeout handler does not behaves as expected and leads to
an unrecoverable state. Rework current implementation of TX Timeout
handling to actually perform a complete reset of the driver state and IP.
We use deferred work to init a task which will be responsible for
resetting the system.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The style of the rx/tx queue's *_coal member assignment is:
static void foo_coal_set(...)
{
set the coal in hw;
update queue's foo_coal member; [1]
}
In other place, we call foo_coal_set(pp, queue->foo_coal), so the above [1]
is duplicated and could be removed.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call of_get_nvmem_mac_address() to fetch the MAC address from an nvmem
cell, if one is provided in the device tree. This allows the address to
be stored in an I2C EEPROM device for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's common practice to store MAC addresses for network interfaces into
nvmem devices. However the code to actually do this in the kernel lacks,
so this patch adds of_get_nvmem_mac_address() for drivers to obtain the
address from an nvmem cell provider.
This is particulary useful on devices where the ethernet interface cannot
be configured by the bootloader, for example because it's in an FPGA.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trigger a port mod message to request an MTU change on the NIC when any
physical port representor is assigned a new MTU value. The driver waits
10 msec for an ack that the FW has set the MTU. If no ack is received the
request is rejected and an appropriate warning flagged.
Rather than maintain an MTU queue per repr, one is maintained per app.
Because the MTU ndo is protected by the rtnl lock, there can never be
contention here. Portmod messages from the NIC are also protected by
rtnl so we first check if the portmod is an ack and, if so, handle outside
rtnl and the cmsg work queue.
Acks are detected by the marking of a bit in a portmod response. They are
then verfied by checking the port number and MTU value expected by the
app. If the expected MTU is 0 then no acks are currently expected.
Also, ensure that the packet headroom reserved by the flower firmware is
considered when accepting an MTU change on any repr.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the 'change_mtu' app callback to 'check_mtu'. This is called
whenever an MTU change is requested on a netdev. It can reject the
change but is not responsible for implementing it.
Introduce a new 'repr_change_mtu' app callback that is hit when the MTU
of a repr is to be changed. This is responsible for performing the MTU
change and verifying it.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.
Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per interrupt
until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had previously
determined instead of the user requested parameters
Fixes: 9f4ca05827a2 ("net: bcmgenet: Add support for adaptive RX coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were a number of issues with setting the RX coalescing parameters:
- we would not be preserving values that would have been configured
across close/open calls, instead we would always reset to no timeout
and 1 interrupt per packet, this would also prevent DIM from setting its
default usec/pkts values
- when adaptive RX would be turned on, we woud not be fetching the
default parameters, we would stay with no timeout/1 packet per
interrupt until the estimator kicks in and changes that
- finally disabling adaptive RX coalescing while providing parameters
would not be honored, and we would stay with whatever DIM had
previously determined instead of the user requested parameters
Fixes: b6e0e875421e ("net: systemport: Implement adaptive interrupt coalescing")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adaptive TX coalescing is not currently giving us any advantages and
ends up making the CPU spin more frequently until TX completion. Deny
and disable adaptive TX coalescing for now and rely on static
configuration, we can always add it back later.
Reviewed-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to return a negative error code from the hash filter init error
handling case instead of 0, as done elsewhere in this function.
Fixes: 5c31254e35a8 ("cxgb4: initialize hash-filter configuration")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit e948bc8fbee0 (cpufreq: Cap the default transition delay
value to 10 ms) the cpufreq was not honouring the delay passed via
ACPI (PCCT). Due to which on ARM based platforms using CPPC the
cpufreq governor tries to change the frequency of CPUs faster than
expected.
This leads to continuous error messages like the following.
" ACPI CPPC: PCC check channel failed. Status=0 "
Earlier (without above commit) the default transition delay was
taken form the value passed from PCCT. Use the same value provided
by PCCT to set the transition_delay_us.
Fixes: e948bc8fbee0 (cpufreq: Cap the default transition delay value to 10 ms)
Signed-off-by: George Cherian <george.cherian@cavium.com>
Cc: 4.14+ <stable@vger.kernel.org> # 4.14+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix once per second (round_robin_time) memory leak of about 1 KB in
each acpi_pad kernel idling thread that is activated.
Found by testing with kmemleak.
Signed-off-by: Lenny Szubowicz <lszubowi@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix a DM multipath regression introduced in a v4.16-rc6 commit:
restore support for loading, and attaching, scsi_dh modules during
multipath table load. Otherwise some users may find themselves unable
to boot, as was reported today:
https://marc.info/?l=linux-scsi&m=152231276114962&w=2
- Fix a DM core ioctl permission check regression introduced in a
v4.16-rc5 commit.
* tag 'for-4.16/dm-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix dropped return code from dm_get_bdev_for_ioctl
dm mpath: fix support for loading scsi_dh modules during table load
|
|
Pull rdma fixes from Jason Gunthorpe:
"It has been fairly silent lately on our -rc front. Big queue of
patches on the mailing list going to for-next though.
Bug fixes:
- qedr driver bugfixes causing application hangs, wrong uapi errnos,
and a race condition
- three syzkaller found bugfixes in the ucma uapi
Regression fixes for things introduced in 4.16:
- Crash on error introduced in mlx5 UMR flow
- Crash on module unload/etc introduced by bad interaction of
restrack and mlx5 patches this cycle
- Typo in a two line syzkaller bugfix causing a bad regression
- Coverity report of nonsense code in hns driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/ucma: Introduce safer rdma_addr_size() variants
RDMA/hns: ensure for-loop actually iterates and free's buffers
RDMA/ucma: Check that device exists prior to accessing it
RDMA/ucma: Check that device is connected prior to access it
RDMA/rdma_cm: Fix use after free race with process_one_req
RDMA/qedr: Fix QP state initialization race
RDMA/qedr: Fix rc initialization on CNQ allocation failure
RDMA/qedr: fix QP's ack timeout configuration
RDMA/ucma: Correct option size check using optlen
RDMA/restrack: Move restrack_clean to be symmetrical to restrack_init
IB/mlx5: Don't clean uninitialized UMR resources
|
|
Pull MTD fixes from Boris Brezillon:
"Two fixes, one in the atmel NAND driver and another one in the
CFI/JEDEC code.
Summary:
- Fix a bug in Atmel ECC engine driver
- Fix a bug in the CFI/JEDEC driver"
* tag 'mtd/fixes-for-4.16' of git://git.infradead.org/linux-mtd:
mtd: jedec_probe: Fix crash in jedec_read_mfr()
mtd: nand: atmel: Fix get_sectorsize() function
|
|
dm_get_bdev_for_ioctl()'s return of 0 or 1 must be the result from
prepare_ioctl (1 means the ioctl was issued to a partition, 0 means it
wasn't). Unfortunately commit 519049afea ("dm: use blkdev_get rather
than bdgrab when issuing pass-through ioctl") reused the variable 'r'
to store the return from blkdev_get() that follows prepare_ioctl()
-- whereby dropping prepare_ioctl()'s result on the floor.
This can lead to an ioctl or persistent reservation being issued to a
partition going unnoticed, which implies the extra permission check for
CAP_SYS_RAWIO is skipped.
Fix this by using a different variable to store blkdev_get()'s return.
Fixes: 519049afea ("dm: use blkdev_get rather than bdgrab when issuing pass-through ioctl")
Reported-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Daniel Borkman says:
====================
pull-request: bpf 2018-03-29
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix nfp to properly check max insn count while emitting
instructions in the JIT which was wrongly comparing bytes
against number of instructions before, from Jakub.
2) Fix for bpftool to avoid usage of hex numbers in JSON
output since JSON doesn't accept hex numbers with 0x
prefix, also from Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ability to have multipath dynamically attach a scsi_dh, that the user
specified in the multipath table, was broken by commit e8f74a0f00 ("dm
mpath: eliminate need to use scsi_device_from_queue").
Restore the ability to load, and attach, a particular scsi_dh module if
one is specified (as noticed by checking m->hw_handler_name).
Fixes: e8f74a0f00 ("dm mpath: eliminate need to use scsi_device_from_queue")
Reported-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.17
Smaller new features to various drivers but nothing really out of
ordinary.
Major changes:
ath10k
* enable chip temperature measurement for QCA6174/QCA9377
* add firmware memory dump for QCA9984
* enable buffer STA on TDLS link for QCA6174
* support different beacon internals in multiple interface scenario
for QCA988X/QCA99X0/QCA9984/QCA4019
iwlwifi
* support for new PCI IDs for the 9000 family
* support for a new firmware API version
* support for advanced dwell and Optimized Connectivity Experience
(OCE) in scanning
btrsi
* fix kconfig dependencies
wil6210
* support multiple virtual interfaces
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
We have a fair number of patches, but many of them are from the
first bullet here:
* EAPoL-over-nl80211 from Denis - this will let us fix
some long-standing issues with bridging, races with
encryption and more
* DFS offload support from the qtnfmac folks
* regulatory database changes for the new ETSI adaptivity
requirements
* various other fixes and small enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vq log_base is the userspace address of bitmap which has nothing to do
with IOTLB. So it needs to be validated unconditionally otherwise we
may try use 0 as log_base which may lead to pin pages that will lead
unexpected result (e.g trigger BUG_ON() in set_bit_to_user()).
Fixes: 6b1e6cc7855b0 ("vhost: new device IOTLB API")
Reported-by: syzbot+6304bf97ef436580fede@syzkaller.appspotmail.com
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VTU miss violations can happen under normal conditions. Don't spam the
kernel log, downgrade the output to debug level only. The statistics
counter will indicate it is happening, if anybody not debugging is
interested.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Count the numbers of various ATU and VTU violation statistics and
return them as part of the ethtool -S statistics.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the following sparse warning:
drivers/net/ethernet/broadcom/genet/bcmgenet.c:1351:16: warning:
Using plain integer as NULL pointer
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Today, driver drops received packets which are indicated as
invalid checksum by the device. Instead of dropping such packets,
pass them to the stack with CHECKSUM_NONE indication in skb.
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cotsworks modules fail the checksums - it appears that Cotsworks
reprograms the EEPROM at the end of production with the final product
information (serial, date code, and exact part number for module
options) and fails to update the checksum.
Work around this by detecting the Cotsworks name in the manufacturer
field, and reducing the checksum failures to warnings rather than a
hard error.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds ethtool callback implementation for flash update.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the required driver support for updating the flash or
non volatile memory of the adapter. At highlevel, flash upgrade comprises
of reading the flash images from the input file, validating the images and
writing them to the respective paritions.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds APIs for flash access.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for populating the flash image attributes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This FW contains several fixes and features
RDMA Features
- SRQ support
- XRC support
- Memory window support
- RDMA low latency queue support
- RDMA bonding support
RDMA bug fixes
- RDMA remote invalidate during retransmit fix
- iWARP MPA connect interop issue with RTR fix
- iWARP Legacy DPM support
- Fix MPA reject flow
- iWARP error handling
- RQ WQE validation checks
MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
for LB packets
ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering
iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration
DEBUG
- Update debug utilities
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During heavy tx traffic, control messages (sent by liquidio driver to NIC
firmware) sometimes do not get processed in a timely manner. Reason is:
the low-level metadata of control messages and that of egress network
packets indicate that they have the same priority.
Fix it by setting a higher priority for control messages through the new
ctrl_qpg field in the oct_txpciq struct. It is the NIC firmware that does
the actual setting of priority by writing to the new ctrl_qpg field; the
host driver treats that value as opaque and just assigns it to pki_ih3->qpg
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink support to netdevsim and use it to implement a simple,
profile based resource controller. Only one controller is needed
per namespace, so the first netdevsim netdevice in a namespace
registers with devlink. If that device is deleted, the resource
settings are deleted.
The resource controller allows a user to limit the number of IPv4 and
IPv6 FIB entries and FIB rules. The resource paths are:
/IPv4
/IPv4/fib
/IPv4/fib-rules
/IPv6
/IPv6/fib
/IPv6/fib-rules
The IPv4 and IPv6 top level resources are unlimited in size and can not
be changed. From there, the number of FIB entries and FIB rule entries
are unlimited by default. A user can specify a limit for the fib and
fib-rules resources:
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib size 96
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib-rules size 16
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib size 64
$ devlink resource set netdevsim/netdevsim0 path /IPv6/fib-rules size 16
$ devlink dev reload netdevsim/netdevsim0
such that the number of rules or routes is limited (96 ipv4 routes in the
example above):
$ for n in $(seq 1 32); do ip ro add 10.99.$n.0/24 dev eth1; done
Error: netdevsim: Exceeded number of supported fib entries.
$ devlink resource show netdevsim/netdevsim0
netdevsim/netdevsim0:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables non
resources:
name fib size 96 occ 96 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables
...
With this template in place for resource management, it is fairly trivial
to extend and shows one way to implement a simple counter based resource
controller typical of network profiles.
Currently, devlink only supports initial namespace. Code is in place to
adapt netdevsim to a per namespace controller once the network namespace
issues are resolved.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-03-27 (Misc updates & SQ recovery)
This series contains Misc updates and cleanups for mlx5e rx path
and SQ recovery feature for tx path.
From Tariq: (RX updates)
- Disable Striding RQ when PCI devices, striding RQ limits the use
of CQE compression feature, which is very critical for slow PCI
devices performance, in this change we will prefer CQE compression
over Striding RQ only on specific "slow" PCIe links.
- RX path cleanups
- Private flag to enable/disable striding RQ
From Eran: (TX fast recovery)
- TX timeout logic improvements, fast SQ recovery and TX error reporting
if a HW error occurs while transmitting on a specific SQ, the driver will
ignore such error and will wait for TX timeout to occur and reset all
the rings. Instead, the current series improves the resiliency for such
HW errors by detecting TX completions with errors, which will report them
and perform a fast recover for the specific faulty SQ even before a TX
timeout is detected.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtnl_lock() is used everywhere, and contention is very high.
When someone wants to iterate over alive net namespaces,
he/she has no a possibility to do that without exclusive lock.
But the exclusive rtnl_lock() in such places is overkill,
and it just increases the contention. Yes, there is already
for_each_net_rcu() in kernel, but it requires rcu_read_lock(),
and this can't be sleepable. Also, sometimes it may be need
really prevent net_namespace_list growth, so for_each_net_rcu()
is not fit there.
This patch introduces new rw_semaphore, which will be used
instead of rtnl_mutex to protect net_namespace_list. It is
sleepable and allows not-exclusive iterations over net
namespaces list. It allows to stop using rtnl_lock()
in several places (what is made in next patches) and makes
less the time, we keep rtnl_mutex. Here we just add new lock,
while the explanation of we can remove rtnl_lock() there are
in next patches.
Fine grained locks generally are better, then one big lock,
so let's do that with net_namespace_list, while the situation
allows that.
Signed-off-by: Kirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that the loop where we read manufacturer
jedec_read_mfd() can under some circumstances get a
CFI_MFR_CONTINUATION repeatedly, making the loop go
over all banks and eventually hit the end of the
map and crash because of an access violation:
Unable to handle kernel paging request at virtual address c4980000
pgd = (ptrval)
[c4980000] *pgd=03808811, *pte=00000000, *ppte=00000000
Internal error: Oops: 7 [#1] PREEMPT ARM
CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150
Hardware name: Gemini (Device Tree)
PC is at jedec_probe_chip+0x6ec/0xcd0
LR is at 0x4
pc : [<c03a2bf4>] lr : [<00000004>] psr: 60000013
sp : c382dd18 ip : 0000ffff fp : 00000000
r10: c0626388 r9 : 00020000 r8 : c0626340
r7 : 00000000 r6 : 00000001 r5 : c3a71afc r4 : c382dd70
r3 : 00000001 r2 : c4900000 r1 : 00000002 r0 : 00080000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 0000397f Table: 00004000 DAC: 00000053
Process swapper (pid: 1, stack limit = 0x(ptrval))
Fix this by breaking the loop with a return 0 if
the offset exceeds the map size.
Fixes: 5c9c11e1c47c ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0")
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
get_sectorsize() was not using the appropriate macro to extract the
ECC sector size from the config cache, which led to buggy ECC when
using 1024 byte sectors.
Fixes: f88fc122cc34 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Reported-by: Olivier Schonken <olivier.schonken@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Olivier Schonken <olivier.schonken@gmail.com>
|
|
We can have interrupts left enabled form e.g: the bootloader which used
the network device for network boot. Make sure we have those disabled as
early as possible to avoid spurious interrupts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the system contains several BGMAC adapters, it is nice to be able
to tell which one is which by looking at /proc/interrupts. Use the
network device name as a name to request_irq() with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
