| Age | Commit message (Collapse) | Author |
|---|
|
Update cache info reporting in sysfs to report the correct
number of CUs and associated cache information based on
different spatial partitioning modes.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently, we store CU info only for a single XCC assuming
that it is the same for all XCCs. However, that may not be
true. As a result, store CU info for all XCCs. This info is
later used for CU masking.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes the following unaligned 64-bit doorbell
warning seen when submitting packets on HIQ on GFX v9.4.3
by making the HIQ doorbell 64-bit aligned.
The warning is seen when GPU is loaded in any mode other
than SPX mode.
[ +0.000301] ------------[ cut here ]------------
[ +0.000003] Unaligned 64-bit doorbell
[ +0.000030] WARNING: /amdkfd/kfd_doorbell.c:339 write_kernel_doorbell64+0x72/0x80
[ +0.000003] RIP: 0010:write_kernel_doorbell64+0x72/0x80
[ +0.000004] RSP: 0018:ffffc90004287730 EFLAGS: 00010246
[ +0.000005] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
[ +0.000003] RDX: 0000000000000001 RSI: ffffffff82837c71 RDI: 00000000ffffffff
[ +0.000003] RBP: ffffc90004287748 R08: 0000000000000003 R09: 0000000000000001
[ +0.000002] R10: 000000000000001a R11: ffff88a034008198 R12: ffffc900013bd004
[ +0.000003] R13: 0000000000000008 R14: ffffc900042877b0 R15: 000000000000007f
[ +0.000003] FS: 00007fa8c7b62000(0000) GS:ffff889f88400000(0000) knlGS:0000000000000000
[ +0.000004] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ +0.000003] CR2: 000056111c45aaf0 CR3: 00000001414f2002 CR4: 0000000000770ee0
[ +0.000003] PKRU: 55555554
[ +0.000002] Call Trace:
[ +0.000004] <TASK>
[ +0.000006] kq_submit_packet+0x45/0x50 [amdgpu]
[ +0.000524] pm_send_set_resources+0x7f/0xc0 [amdgpu]
[ +0.000500] set_sched_resources+0xe4/0x160 [amdgpu]
[ +0.000503] start_cpsch+0x1c5/0x2a0 [amdgpu]
[ +0.000497] kgd2kfd_device_init.cold+0x816/0xb42 [amdgpu]
[ +0.000743] amdgpu_amdkfd_device_init+0x15f/0x1f0 [amdgpu]
[ +0.000602] amdgpu_device_init.cold+0x1813/0x2176 [amdgpu]
[ +0.000684] ? pci_bus_read_config_word+0x4a/0x80
[ +0.000012] ? do_pci_enable_device+0xdc/0x110
[ +0.000008] amdgpu_driver_load_kms+0x1a/0x110 [amdgpu]
[ +0.000545] amdgpu_pci_probe+0x197/0x400 [amdgpu]
Fixes: c31866651086 ("drm/amdgpu: use doorbell mgr for kfd kernel doorbells")
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch fixes the case where the code currently passes
absolute register address and not the reg offset, which HWS
expects, when sending the PM4 packet to set/update CWSR grace
period. Additionally, cleanup the signature of
build_grace_period_packet_info function as it no longer needs
the inst parameter.
Signed-off-by: Mukul Joshi <mukul.joshi@amd.com>
Reviewed-by: Jonathan Kim <jonathan.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a compile error when this commit is added:
md: raid1: fix potential OOB in raid1_remove_disk()
drivers/md/raid1.c: In function 'raid1_remove_disk':
drivers/md/raid1.c:1844:9: error: ISO C90 forbids mixed declarations
and code [-Werror=declaration-after-statement]
1844 | struct raid1_info *p = conf->mirrors + number;
| ^~~~~~
That's because the new code was inserted before the struct.
The change is move the struct command above this commit.
Fixes: 8b0472b50bcf ("md: raid1: fix potential OOB in raid1_remove_disk()")
Signed-off-by: Nigel Croxon <ncroxon@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/46d929d0-2aab-4cf2-b2bf-338963e8ba5a@redhat.com
|
|
Rework the write operation such that the Byte Count register is written with
a single raw i2c write outside of regmap using transfer which does specify
the number of bytes to be transfered, one in this case, and which makes the
expected subsequent write transfer look like address+register+data, and then
make use of this method. Without this change, the Byte Count register write
in probe() would succeed as it would provide the byte count as part of its
write payload, but any subsequent writes would fail due to this Byte Count
register programming. Such failing writes happens e.g. during resume, when
restoring the regmap content.
Fixes: edc12763a3a2 ("clk: si521xx: Clock driver for Skyworks Si521xx I2C PCIe clock generators")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230831181656.154750-2-marex@denx.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
In order to reload registers into the clock generator on resume using
regcache_sync(), it is necessary to select one of the regcache types
which are not NONE. Since this device has some 7 registers, use the
simplest one, FLAT. The regcache code complains about REGCACHE_NONE
being selected and generates a WARNING, this fixes that warning.
Fixes: edc12763a3a2 ("clk: si521xx: Clock driver for Skyworks Si521xx I2C PCIe clock generators")
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230831181656.154750-1-marex@denx.de
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The thm*_clk have two clock sources 32k and 250k,excluding 32m.
Fixes: af3bd36573e3 ("clk: sprd: Add clocks support for UMS512")
Signed-off-by: Zhifeng Tang <zhifeng.tang@unisoc.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Reviewed-by: Baolin Wang <baolin.wang@linux.alibaba.com>
Link: https://lore.kernel.org/r/20230824092624.20020-1-zhifeng.tang@unisoc.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Make vc3_clk_mux enum values depend upon vc3_clk enum values to avoid
any accidental breakage in the future.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230824104812.147775-5-biju.das.jz@bp.renesas.com
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
According to Table 3. ("Output Source") in the 5P35023 datasheet,
the output clock mapping should be 0=REF, 1=SE1, 2=SE2, 3=SE3,
4=DIFF1, 5=DIFF2. But the code uses inverse. Fix this mapping issue.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Closes: https://lore.kernel.org/all/CAMuHMdUHD+bEco=WYTYWsTAyRt3dTQQt4Xpaejss0Y2ZpLCMNg@mail.gmail.com/
Fixes: 6e9aff555db7 ("clk: Add support for versa3 clock driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230824104812.147775-4-biju.das.jz@bp.renesas.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Fix the below cocci warnings by replacing do_div()->div64_ul() and
bound the result with a max value of U16_MAX.
cocci warnings:
drivers/clk/clk-versaclock3.c:404:2-8: WARNING: do_div() does a
64-by-32 division, please consider using div64_ul instead.
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Closes: https://lore.kernel.org/r/202307270841.yr5HxYIl-lkp@intel.com/
Fixes: 6e9aff555db7 ("clk: Add support for versa3 clock driver")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230824104812.147775-3-biju.das.jz@bp.renesas.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Intel Granite Rapids has a flash controller that is compatible with the
other Cannon Lake derivatives. Add Granite Rapids PCI ID to the driver
list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20230911074616.3473347-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When mt6370_chg_field_get() suceeds, ret is set to zero and returning
zero when flash led is still in strobe mode looks incorrect.
Fixes: 233cb8a47d65 ("power: supply: mt6370: Add MediaTek MT6370 charger driver")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: ChiaEn Wu <chiaen_wu@richtek.com>
Link: https://lore.kernel.org/r/20230906084815.2827930-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add 'const' to the definition of the 'trip' argument of the
.get_trend() thermal zone callback to indicate that the trip point
passed to it should not be modified by it and adjust the
callback functions implementing it, thermal_get_trend() in the
ACPI thermal driver and __ti_thermal_get_trend(), accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
|
|
for_each_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an
of_node_put.
This was done using the Coccinelle semantic patch
iterators/for_each_child.cocci
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
Short summary of fixes pull:
* nouveau: Lockdep workaround
* fbdev/g364fb: Build fix
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230911141915.GA983@linux-uq9g
|
|
A few lines above, space is kzalloc()'ed for:
sizeof(struct iwl_nvm_data) +
sizeof(struct ieee80211_channel) +
sizeof(struct ieee80211_rate)
'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine.
At the end of this structure, there is the 'channels' flex array.
Each element is of type 'struct ieee80211_channel'.
So only 1 element is allocated in this array.
When doing:
mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels;
We point at the first element of the 'channels' flex array.
So this is fine.
However, when doing:
mvm->nvm_data->bands[0].bitrates =
(void *)((u8 *)mvm->nvm_data->channels + 1);
because of the "(u8 *)" cast, we add only 1 to the address of the beginning
of the flex array.
It is likely that we want point at the 'struct ieee80211_rate' allocated
just after.
Remove the spurious casting so that the pointer arithmetic works as
expected.
Fixes: 8ca151b568b6 ("iwlwifi: add the MVM driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/23f0ec986ef1529055f4f93dcb3940a6cf8d9a94.1690143750.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Debugging indicates that nothing else is clearing the info->flags,
so some frames were flagged as ACKed when they should not be.
Explicitly clear the ack flag to ensure this does not happen.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230808205605.4105670-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The iwl_fw_ini_error_dump_range structure has conflicting alignment
requirements for the inner union and the outer struct:
In file included from drivers/net/wireless/intel/iwlwifi/fw/dbg.c:9:
drivers/net/wireless/intel/iwlwifi/fw/error-dump.h:312:2: error: field within 'struct iwl_fw_ini_error_dump_range' is less aligned than 'union iwl_fw_ini_error_dump_range::(anonymous at drivers/net/wireless/intel/iwlwifi/fw/error-dump.h:312:2)' and is usually due to 'struct iwl_fw_ini_error_dump_range' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
union {
As the original intention was apparently to make the entire structure
unaligned, mark the innermost members the same way so the union
becomes packed as well.
Fixes: 973193554cae6 ("iwlwifi: dbg_ini: dump headers cleanup")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230616090343.2454061-1-arnd@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use the correct field to fix wrong voltage range selection on regulators
such as tps6287x since the blamed commit.
Fixes: 269cb04b601d ("regulator: Use bitfield values for range selectors")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20230911-regulator-voltage-sel-v1-1-886eb1ade8d8@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Making sure the UCSI debugfs entry actually exists before
attempting to remove it.
Fixes: df0383ffad64 ("usb: typec: ucsi: Add debugfs for ucsi commands")
Reported-by: Dave Hansen <dave.hansen@intel.com>
Closes: https://lore.kernel.org/linux-usb/700df3c4-2f6c-85f9-6c61-065bc5b2db3a@intel.com/
Suggested-by: Dave Hansen <dave.hansen@intel.com>
Suggested-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: Saranya Gopal <saranya.gopal@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Link: https://lore.kernel.org/r/20230906084842.1922052-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add quirk for ASUS ROG X16 (GV601V, 2023 versions) Flow 2-in-1
to enable tablet mode with lid flip (all screen rotations).
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Link: https://lore.kernel.org/r/20230905082813.13470-1-luke@ljones.dev
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The only probing method supported by the Nvidia SN2201 platform driver
is probing through an ACPI match table. Hence add a dependency on
ACPI, to prevent asking the user about this driver when configuring a
kernel without ACPI support.
Fixes: 662f24826f95 ("platform/mellanox: Add support for new SN2201 system")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/ec5a4071691ab08d58771b7732a9988e89779268.1693828363.git.geert+renesas@glider.be
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The latest version of the mlxbf_bootctl driver utilizes
"sysfs_format_mac", and this API is only available if
NET is defined in the kernel configuration. This patch
changes the mlxbf_bootctl Kconfig to depend on NET.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309031058.JvwNDBKt-lkp@intel.com/
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/20230905133243.31550-1-davthompson@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This fix involves 2 changes:
- All event regs have a reset value of 0, which is not a valid
event_number as per the event_list for most blocks and hence seen
as an error. Add a "disable" event with event_number 0 for all blocks.
- The enable bit for each counter need not be checked before
reading the event info, and hence removed.
Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/04d0213932d32681de1c716b54320ed894e52425.1693917738.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Replace sprintf with sysfs_emit where possible.
Size check in mlxbf_pmc_event_list_show should account for "\0".
Fixes: 1a218d312e65 ("platform/mellanox: mlxbf-pmc: Add Mellanox BlueField PMC driver")
Signed-off-by: Shravan Kumar Ramani <shravankr@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/bef39ef32319a31b32f999065911f61b0d3b17c3.1693917738.git.shravankr@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This commit drops over-sized network packets to avoid tmfifo
queue stuck.
Fixes: 1357dfd7261f ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/9318936c2447f76db475c985ca6d91f057efcd41.1693322547.git.limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
This commit fixes tmfifo console stuck issue when the virtual
networking interface is in down state. In such case, the network
Rx descriptors runs out and causes the Rx network packet staying
in the head of the tmfifo thus blocking the console packets. The
fix is to drop the Rx network packet when no more Rx descriptors.
Function name mlxbf_tmfifo_release_pending_pkt() is also renamed
to mlxbf_tmfifo_release_pkt() to be more approperiate.
Fixes: 1357dfd7261f ("platform/mellanox: Add TmFifo driver for Mellanox BlueField Soc")
Signed-off-by: Liming Sun <limings@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: David Thompson <davthompson@nvidia.com>
Link: https://lore.kernel.org/r/8c0177dc938ae03f52ff7e0b62dbeee74b7bec09.1693322547.git.limings@nvidia.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
I had the following weird phenomena on a mobile phone: while
the capacity in /sys/class/power_supply/ab8500_fg/capacity
would reflect the actual charge and capacity of the battery,
only 1/3 of the value was shown on the battery status
indicator and warnings for low battery appeared.
It turns out that UPower, the Freedesktop power daemon,
will average all the power supplies of type "battery" in
/sys/class/power_supply/* if there is more than one battery.
For the AB8500, there was "battery" ab8500_fg, ab8500_btemp
and ab8500_chargalg. The latter two don't know anything
about the battery, and should not be considered. They were
however averaged and with the capacity of 0.
Flag ab8500_btemp and ab8500_chargalg with type "unknown"
so they are not averaged as batteries.
Remove the technology prop from ab8500_btemp as well, all
it does is snoop in on knowledge from another supply.
After this the battery indicator shows the right value.
Cc: Stefan Hansson <newbyte@disroot.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Handling of BSS_CHANGED_PS was missing in vif_cfg_changed
callback. Fix it.
Fixes: 22c588343529 ("wifi: iwlwifi: mvm: replace bss_info_changed() with vif_cfg/link_info_changed()")
Reported-by: Sultan Alsawaf <sultan@kerneltoast.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230905162939.5ef0c8230de6.Ieed265014988c50ec68fbff6d33821e4215f987f@changeid
[note: patch looks bigger than it is due to reindentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
MT7988 SoC support 3 NICs. Fix pse_port configuration in
mtk_flow_set_output_device routine if the traffic is offloaded to eth2.
Rely on mtk_pse_port definitions.
Fixes: 88efedf517e6 ("net: ethernet: mtk_eth_soc: enable nft hw flowtable_offload for MT7988 SoC")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Variable dma_addr in function mtk_poll_rx can be uninitialized on
some of the error paths. In practise this doesn't matter, even random
data present in uninitialized stack memory can safely be used in the
way it happens in the error path.
However, in order to make Smatch happy make sure the variable is
always initialized.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The perf power scale value would currently be reported as bogowatts if the
platform firmware supports microwatt power scale and meets the perf major
version requirements. Fix this by populating version information in the
driver private data before the call to protocol attributes is made.
CC: Chandra Sekhar Lingutla <quic_lingutla@quicinc.com>
Fixes: 3630cd8130ce ("firmware: arm_scmi: Add SCMI v3.1 perf power-cost in microwatts")
Signed-off-by: Sibi Sankar <quic_sibis@quicinc.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Link: https://lore.kernel.org/r/20230811204818.30928-1-quic_sibis@quicinc.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e4454 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when we add the first sja1105 port to a bridge with
vlan_filtering 1, then we sometimes see this output:
sja1105 spi2.2: port 4 failed to read back entry for be:79:b4:9e:9e:96 vid 3088: -ENOENT
sja1105 spi2.2: Reset switch and programmed static config. Reason: VLAN filtering
sja1105 spi2.2: port 0 failed to add be:79:b4:9e:9e:96 vid 0 to fdb: -2
It is because sja1105_fdb_add() runs from the dsa_owq which is no longer
serialized with switch resets since it dropped the rtnl_lock() in the
blamed commit.
Either performing the FDB accesses before the reset, or after the reset,
is equally fine, because sja1105_static_fdb_change() backs up those
changes in the static config, but FDB access during reset isn't ok.
Make sja1105_static_config_reload() take the fdb_lock to fix that.
Fixes: 0faf890fc519 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sja1105_fdb_add() runs from the dsa_owq, and sja1105_port_mcast_flood()
runs from switchdev_deferred_process_work(). Prior to the blamed commit,
they used to be indirectly serialized through the rtnl_lock(), which
no longer holds true because dsa_owq dropped that.
So, it is now possible that we traverse the static config BLK_IDX_L2_LOOKUP
elements concurrently compared to when we change them, in
sja1105_static_fdb_change(). That is not ideal, since it might result in
data corruption.
Introduce a mutex which serializes accesses to the hardware FDB and to
the static config elements for the L2 Address Lookup table.
I can't find a good reason to add locking around sja1105_fdb_dump().
I'll add it later if needed.
Fixes: 0faf890fc519 ("net: dsa: drop rtnl_lock from dsa_slave_switchdev_event_work")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
entry
The commit cited in Fixes: did 2 things: it refactored the read-back
polling from sja1105_dynamic_config_read() into a new function,
sja1105_dynamic_config_wait_complete(), and it called that from
sja1105_dynamic_config_write() too.
What is problematic is the refactoring.
The refactored code from sja1105_dynamic_config_poll_valid() works like
the previous one, but the problem is that it uses another packed_buf[]
SPI buffer, and there was code at the end of sja1105_dynamic_config_read()
which was relying on the read-back packed_buf[]:
/* Don't dereference possibly NULL pointer - maybe caller
* only wanted to see whether the entry existed or not.
*/
if (entry)
ops->entry_packing(packed_buf, entry, UNPACK);
After the change, the packed_buf[] that this code sees is no longer the
entry read back from hardware, but the original entry that the caller
passed to the sja1105_dynamic_config_read(), packed into this buffer.
This difference is the most notable with the SJA1105_SEARCH uses from
sja1105pqrs_fdb_add() - used for both fdb and mdb. There, we have logic
added by commit 728db843df88 ("net: dsa: sja1105: ignore the FDB entry
for unknown multicast when adding a new address") to figure out whether
the address we're trying to add matches on any existing hardware entry,
with the exception of the catch-all multicast address.
That logic was broken, because with sja1105_dynamic_config_read() not
working properly, it doesn't return us the entry read back from
hardware, but the entry that we passed to it. And, since for multicast,
a match will always exist, it will tell us that any mdb entry already
exists at index=0 L2 Address Lookup table. It is index=0 because the
caller doesn't know the index - it wants to find it out, and
sja1105_dynamic_config_read() does:
if (index < 0) { // SJA1105_SEARCH
/* Avoid copying a signed negative number to an u64 */
cmd.index = 0; // <- this
cmd.search = true;
} else {
cmd.index = index;
cmd.search = false;
}
So, to the caller of sja1105_dynamic_config_read(), the returned info
looks entirely legit, and it will add all mdb entries to FDB index 0.
There, they will always overwrite each other (not to mention,
potentially they can also overwrite a pre-existing bridge fdb entry),
and the user-visible impact will be that only the last mdb entry will be
forwarded as it should. The others won't (will be flooded or dropped,
depending on the egress flood settings).
Fixing is a bit more complicated, and involves either passing the same
packed_buf[] to sja1105_dynamic_config_wait_complete(), or moving all
the extra processing on the packed_buf[] to
sja1105_dynamic_config_wait_complete(). I've opted for the latter,
because it makes sja1105_dynamic_config_wait_complete() a bit more
self-contained.
Fixes: df405910ab9f ("net: dsa: sja1105: wait for dynamic config command completion on writes too")
Reported-by: Yanan Yang <yanan.yang@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sja1105_dynamic_config_poll_valid()
Currently, sja1105_dynamic_config_wait_complete() returns either 0 or
-ETIMEDOUT, because it just looks at the read_poll_timeout() return code.
There will be future changes which move some more checks to
sja1105_dynamic_config_poll_valid(). It is important that we propagate
their exact return code (-ENOENT, -EINVAL), because callers of
sja1105_dynamic_config_read() depend on them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4d9423549501 ("net: dsa: sja1105: offload bridge port flags to
device") has partially hidden some multicast entries from showing up in
the "bridge fdb show" output, but it wasn't enough. Addresses which are
added through "bridge mdb add" still show up. Hide them all.
Fixes: 291d1e72b756 ("net: dsa: sja1105: Add support for FDB and MDB management")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when a new fdb entry is added (with both ports of the
ADIN2111 bridged), the driver configures the MAC filters for the wrong
port, which results in the forwarding being done by the host, and not
actually hardware offloaded.
The ADIN2111 offloads the forwarding by setting filters on the
destination MAC address of incoming frames. Based on these, they may be
routed to the other port. Thus, if a frame has to be forwarded from port
1 to port 2, the required configuration for the ADDR_FILT_UPRn register
should set the APPLY2PORT1 bit (instead of APPLY2PORT2, as it's
currently the case).
Fixes: bc93e19d088b ("net: ethernet: adi: Add ADIN1110 support")
Signed-off-by: Ciprian Regus <ciprian.regus@analog.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mtk_hwlro_get_fdir_all()
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid NULL pointer dereference.
Fixes: 7aab747e5563 ("net: ethernet: mediatek: add ethtool functions to configure RX flows of HW LRO")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rules is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rules to avoid OOB writing or NULL pointer dereference.
Fixes: 90b509b39ac9 ("net: mvpp2: cls: Add Classification offload support")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rule_locs is allocated in ethtool_get_rxnfc and the size is determined by
rule_cnt from user space. So rule_cnt needs to be check before using
rule_locs to avoid OOB writing or NULL pointer dereference.
Fixes: c5d511c49587 ("net: bcmasp: Add support for wake on net filters")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting ethtool -C eth0 tx-usecs 0 is supposed to disable the use of the
coalescing timer but currently it gets programmed with zero delay
instead.
Disable the use of the coalescing timer if tx-usecs is zero by
preventing it from being restarted. Note that to keep things simple we
don't start/stop the timer when the coalescing settings are changed, but
just let that happen on the next transmit or timer expiry.
Fixes: 8fce33317023 ("net: stmmac: Rework coalesce timer and fix multi-queue races")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kyril reports that crashkernels fail to work on confidential VMs that
rely on the unaccepted memory table, and this appears to be caused by
the fact that it is not considered part of the set of firmware tables
that the crashkernel needs to map.
This is an oversight, and a result of the use of the EFI_LOADER_DATA
memory type for this table. The correct memory type to use for any
firmware table is EFI_ACPI_RECLAIM_MEMORY (including ones created by the
EFI stub), even though the name suggests that is it specific to ACPI.
ACPI reclaim means that the memory is used by the firmware to expose
information to the operating system, but that the memory region has no
special significance to the firmware itself, and the OS is free to
reclaim the memory and use it as ordinary memory if it is not interested
in the contents, or if it has already consumed them. In Linux, this
memory is never reclaimed, but it is always covered by the kernel direct
map and generally made accessible as ordinary memory.
On x86, ACPI reclaim memory is translated into E820_ACPI, which the
kexec logic already recognizes as memory that the crashkernel may need
to to access, and so it will be mapped and accessible to the booting
crash kernel.
Fixes: 745e3ed85f71 ("efi/libstub: Implement support for unaccepted memory")
Reported-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
snprintf() returns the "number of characters which *would* be generated for
the given input", not the size *really* generated.
In order to avoid too large values for 'o' (and potential negative values
for "sizeof(linebuf) o") use scnprintf() instead of snprintf().
Note that given the "w < 4" in the for loop, the buffer can NOT
overflow, but using the *right* function is always better.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."
In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."
Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.
DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.
sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.
This change is based on a patch originally submitted by Runa Guo-oc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a6e ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Commit feaa8baee82a ("bus: ti-sysc: Implement SoC revision handling")
created a list of SoC types searching for strings based on names
and wildcards which associates the SoC to different families.
The OMAP34xx and OMAP35xx are treated as SOC_3430 while
OMAP36xx and OMAP37xx are treated as SOC_3630, but the AM35xx
isn't listed.
The AM35xx is mostly an OMAP3430, and a later commit a12315d6d270
("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific") looks
for the SOC type and behaves in a certain way if it's SOC_3430.
This caused a regression on the AM3517 causing it to return two
errors:
ti-sysc: probe of 48318000.target-module failed with error -16
ti-sysc: probe of 49032000.target-module failed with error -16
Fix this by treating the creating SOC_AM35 and inserting it between
the SOC_3430 and SOC_3630. If it is treaed the same way as the
SOC_3430 when checking the status of sysc_check_active_timer,
the error conditions will disappear.
Fixes: a12315d6d270 ("bus: ti-sysc: Make omap3 gpt12 quirk handling SoC specific")
Fixes: feaa8baee82a ("bus: ti-sysc: Implement SoC revision handling")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-ID: <20230906233442.270835-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The am335x-evm started producing boot errors because of subtle timing
changes:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xf03c1010
...
sysc_reset from sysc_probe+0xf60/0x1514
sysc_probe from platform_probe+0x5c/0xbc
...
The fix consists in using the appropriate sleep function in sysc reset.
For flexible sleeping, fsleep is recommended. Here, sysc delay parameter
can take any value in [0 - 255] us range. As a result, fsleep() should
be used, calling udelay() for a sysc delay lower than 10 us.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Fixes: e709ed70d122 ("bus: ti-sysc: Fix missing reset delay handling")
Message-ID: <20230821-fix-ti-sysc-reset-v1-1-5a0a5d8fae55@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As explained in errata sheet, in section "2.14.5 Truncation of SPI output
signals after EOT event":
On STM32MP1x, EOT interrupt can be thrown before the true end of
communication.
So we add a delay of a half period to wait the real end of the
transmission.
Link: https://www.st.com/resource/en/errata_sheet/es0539-stm32mp131x3x5x-device-errata-stmicroelectronics.pdf
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230906132735.748174-1-valentin.caron@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
