| Age | Commit message (Collapse) | Author |
|---|
|
Add support for mcan bit timing and control mode according to bosch mcan IP
version 3.3.0. The mcan version read from the Core Release field of CREL
register would be 33. Accordingly the properties are to be set for mcan v3.3.0
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/1606366302-5520-1-git-send-email-pankj.sharma@samsung.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0e1 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
request_threaded_irq()'s flags
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Currently lock gets freed only if timeout expires, but missed a
case when HW returns failure and goes for cleanup.
Fixes: efca3878a5fb ("ch_ktls: Issue if connection offload fails")
Signed-off-by: Rohit Maheshwari <rohitm@chelsio.com>
Link: https://lore.kernel.org/r/20201125072626.10861-1-rohitm@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Feed kstrtou8 with NULL terminated string.
Changes since v1:
-Use sscanf to get rid of adhoc string parse.
Changes since v2:
-Check if sscanf returns 3.
Fixes: 7ea5fda2b132 ("ptp: ptp_clockmatrix: update to support 4.8.7 firmware")
Signed-off-by: Min Li <min.li.xe@renesas.com>
Link: https://lore.kernel.org/r/1606273115-25792-1-git-send-email-min.li.xe@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The tc-taprio base time indicates the beginning of the tc-taprio
schedule, which is cyclic by definition (where the length of the cycle
in nanoseconds is called the cycle time). The base time is a 64-bit PTP
time in the TAI domain.
Logically, the base-time should be a future time. But that imposes some
restrictions to user space, which has to retrieve the current PTP time
from the NIC first, then calculate a base time that will still be larger
than the base time by the time the kernel driver programs this value
into the hardware. Actually ensuring that the programmed base time is in
the future is still a problem even if the kernel alone deals with this.
Luckily, the enetc hardware already advances a base-time that is in the
past into a congruent time in the immediate future, according to the
same formula that can be found in the software implementation of taprio
(in taprio_get_start_time):
/* Schedule the start time for the beginning of the next
* cycle.
*/
n = div64_s64(ktime_sub_ns(now, base), cycle);
*start = ktime_add_ns(base, (n + 1) * cycle);
There's only one problem: the driver doesn't let the hardware do that.
It interferes with the base-time passed from user space, by special-casing
the situation when the base-time is zero, and replaces that with the
current PTP time. This changes the intended effective base-time of the
schedule, which will in the end have a different phase offset than if
the base-time of 0.000000000 was to be advanced by an integer multiple
of the cycle-time.
Fixes: 34c6adf1977b ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201124220259.3027991-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 757926247836 ("net: stmmac: add flexible PPS to dwmac
4.10a") was intended to modify the struct dwmac410_ops, but it got
somehow badly merged and modified the struct dwmac4_ops.
Revert the modification in struct dwmac4_ops and re-apply it
properly in struct dwmac410_ops.
Fixes: 757926247836 ("net: stmmac: add flexible PPS to dwmac 4.10a")
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Reported-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20201124223729.886992-1-antonio.borneo@st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Based on the discussion with Sukadev Bhattiprolu and Dany Madden,
we believe that checking adapter->resetting bit is preferred
since RESETTING state flag is not as strict as resetting bit.
RESETTING state flag is removed since it is verbose now.
Fixes: 7d7195a026ba ("ibmvnic: Do not process device remove during device reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
crq->msgs could be NULL if the previous reset did not complete after
freeing crq->msgs. Check for NULL before dereferencing them.
Snippet of call trace:
...
ibmvnic 30000003 env3 (unregistering): Releasing sub-CRQ
ibmvnic 30000003 env3 (unregistering): Releasing CRQ
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc0000000000c1a30
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: ibmvnic(E-) rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag tun raw_diag inet_diag unix_diag bridge af_packet_diag netlink_diag stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod [last unloaded: ibmvnic]
CPU: 20 PID: 8426 Comm: kworker/20:0 Tainted: G E 5.10.0-rc1+ #12
Workqueue: events __ibmvnic_reset [ibmvnic]
NIP: c0000000000c1a30 LR: c008000001b00c18 CTR: 0000000000000400
REGS: c00000000d05b7a0 TRAP: 0380 Tainted: G E (5.10.0-rc1+)
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 44002480 XER: 20040000
CFAR: c0000000000c19ec IRQMASK: 0
GPR00: 0000000000000400 c00000000d05ba30 c008000001b17c00 0000000000000000
GPR04: 0000000000000000 0000000000000000 0000000000000000 00000000000001e2
GPR08: 000000000001f400 ffffffffffffd950 0000000000000000 c008000001b0b280
GPR12: c0000000000c19c8 c00000001ec72e00 c00000000019a778 c00000002647b440
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000006 0000000000000001 0000000000000003 0000000000000002
GPR24: 0000000000001000 c008000001b0d570 0000000000000005 c00000007ab5d550
GPR28: c00000007ab5c000 c000000032fcf848 c00000007ab5cc00 c000000032fcf800
NIP [c0000000000c1a30] memset+0x68/0x104
LR [c008000001b00c18] ibmvnic_reset_crq+0x70/0x110 [ibmvnic]
Call Trace:
[c00000000d05ba30] [0000000000000800] 0x800 (unreliable)
[c00000000d05bab0] [c008000001b0a930] do_reset.isra.40+0x224/0x634 [ibmvnic]
[c00000000d05bb80] [c008000001b08574] __ibmvnic_reset+0x17c/0x3c0 [ibmvnic]
[c00000000d05bc50] [c00000000018d9ac] process_one_work+0x2cc/0x800
[c00000000d05bd20] [c00000000018df58] worker_thread+0x78/0x520
[c00000000d05bdb0] [c00000000019a934] kthread+0x1c4/0x1d0
[c00000000d05be20] [c00000000000d5d0] ret_from_kernel_thread+0x5c/0x6c
Fixes: 032c5e82847a ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
adapter->tx_scrq and adapter->rx_scrq could be NULL if the previous reset
did not complete after freeing sub crqs. Check for NULL before
dereferencing them.
Snippet of call trace:
ibmvnic 30000006 env6: Releasing sub-CRQ
ibmvnic 30000006 env6: Releasing CRQ
...
ibmvnic 30000006 env6: Got Control IP offload Response
ibmvnic 30000006 env6: Re-setting tx_scrq[0]
BUG: Kernel NULL pointer dereference on read at 0x00000000
Faulting instruction address: 0xc008000003dea7cc
Oops: Kernel access of bad area, sig: 11 [#1]
LE PAGE_SIZE=64K MMU=Hash SMP NR_CPUS=2048 NUMA pSeries
Modules linked in: rpadlpar_io rpaphp xt_CHECKSUM xt_MASQUERADE xt_conntrack ipt_REJECT nf_reject_ipv4 nft_compat nft_counter nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables xsk_diag tcp_diag udp_diag raw_diag inet_diag unix_diag af_packet_diag netlink_diag tun bridge stp llc rfkill sunrpc pseries_rng xts vmx_crypto uio_pdrv_genirq uio binfmt_misc ip_tables xfs libcrc32c sd_mod t10_pi sg ibmvscsi ibmvnic ibmveth scsi_transport_srp dm_mirror dm_region_hash dm_log dm_mod
CPU: 80 PID: 1856 Comm: kworker/80:2 Tainted: G W 5.8.0+ #4
Workqueue: events __ibmvnic_reset [ibmvnic]
NIP: c008000003dea7cc LR: c008000003dea7bc CTR: 0000000000000000
REGS: c0000007ef7db860 TRAP: 0380 Tainted: G W (5.8.0+)
MSR: 800000000280b033 <SF,VEC,VSX,EE,FP,ME,IR,DR,RI,LE> CR: 28002422 XER: 0000000d
CFAR: c000000000bd9520 IRQMASK: 0
GPR00: c008000003dea7bc c0000007ef7dbaf0 c008000003df7400 c0000007fa26ec00
GPR04: c0000007fcd0d008 c0000007fcd96350 0000000000000027 c0000007fcd0d010
GPR08: 0000000000000023 0000000000000000 0000000000000000 0000000000000000
GPR12: 0000000000002000 c00000001ec18e00 c0000000001982f8 c0000007bad6e840
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 0000000000000000 0000000000000000 fffffffffffffef7
GPR24: 0000000000000402 c0000007fa26f3a8 0000000000000003 c00000016f8ec048
GPR28: 0000000000000000 0000000000000000 0000000000000000 c0000007fa26ec00
NIP [c008000003dea7cc] ibmvnic_reset_init+0x15c/0x258 [ibmvnic]
LR [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic]
Call Trace:
[c0000007ef7dbaf0] [c008000003dea7bc] ibmvnic_reset_init+0x14c/0x258 [ibmvnic] (unreliable)
[c0000007ef7dbb80] [c008000003de8860] __ibmvnic_reset+0x408/0x970 [ibmvnic]
[c0000007ef7dbc50] [c00000000018b7cc] process_one_work+0x2cc/0x800
[c0000007ef7dbd20] [c00000000018bd78] worker_thread+0x78/0x520
[c0000007ef7dbdb0] [c0000000001984c4] kthread+0x1d4/0x1e0
[c0000007ef7dbe20] [c00000000000cea8] ret_from_kernel_thread+0x5c/0x74
Fixes: 57a49436f4e8 ("ibmvnic: Reset sub-crqs during driver reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch fixes two lines in which the rx_offset received by the device
wasn't taken into account:
- prefetch function:
In our driver the copied data would reside in
rx_info->page + rx_headroom + rx_offset
so the prefetch function is changed accordingly.
- setting page_offset to zero for descriptors > 1:
for every descriptor but the first, the rx_offset is zero. Hence
the page_offset value should be set to rx_headroom.
The previous implementation changed the value of rx_info after
the descriptor was added to the SKB (essentially providing wrong
page offset).
Fixes: 68f236df93a9 ("net: ena: add support for the rx offset feature")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ENA driver uses the readless mechanism, which uses DMA, to find
out what the DMA mask is supposed to be.
If DMA is used without setting the dma_mask first, it causes the
Intel IOMMU driver to think that ENA is a 32-bit device and therefore
disables IOMMU passthrough permanently.
This patch sets the dma_mask to be ENA_MAX_PHYS_ADDR_SIZE_BITS=48
before readless initialization in
ena_device_init()->ena_com_mmio_reg_read_request_init(),
which is large enough to workaround the intel_iommu issue.
DMA mask is set again to the correct value after it's received from the
device after readless is initialized.
The patch also changes the driver to use dma_set_mask_and_coherent()
function instead of the two pci_set_dma_mask() and
pci_set_consistent_dma_mask() ones. Both methods achieve the same
effect.
Fixes: 1738cd3ed342 ("net: ena: Add a driver for Amazon Elastic Network Adapters (ENA)")
Signed-off-by: Mike Cui <mikecui@amazon.com>
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After request id is checked in validate_rx_req_id() its value is still
used in the line
rx_ring->free_ids[next_to_clean] =
rx_ring->ena_bufs[i].req_id;
even if it was found to be out-of-bound for the array free_ids.
The patch moves the request id to an earlier stage in the napi routine and
makes sure its value isn't used if it's found out-of-bounds.
Fixes: 30623e1ed116 ("net: ena: avoid memory access violation by validating req_id properly")
Signed-off-by: Ido Segev <idose@amazon.com>
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
GPIOs - as returned by of_get_named_gpio() and used by the gpiolib - are
signed integers, where negative number indicates error. The return
value of of_get_named_gpio() should not be assigned to an unsigned int
because in case of !CONFIG_GPIOLIB such number would be a valid GPIO.
Fixes: c04c674fadeb ("nfc: s3fwrn5: Add driver for Samsung S3FWRN5 NFC Chip")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201123162351.209100-1-krzk@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dpaa2 driver depends on devlink, so it should select
NET_DEVLINK in order to fix compile errors, such as:
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth.o: in function `dpaa2_eth_rx_err':
dpaa2-eth.c:(.text+0x3cec): undefined reference to `devlink_trap_report'
drivers/net/ethernet/freescale/dpaa2/dpaa2-eth-devlink.o: in function `dpaa2_eth_dl_info_get':
dpaa2-eth-devlink.c:(.text+0x160): undefined reference to `devlink_info_driver_name_put'
Fixes: ceeb03ad8e22 ("dpaa2-eth: add basic devlink support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201123163553.1666476-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When performing IPv6 forwarding, there is an expectation that SKBs
will have some headroom. When forwarding a packet from the aquantia
driver, this does not always happen, triggering a kernel warning.
aq_ring.c has this code (edited slightly for brevity):
if (buff->is_eop && buff->len <= AQ_CFG_RX_FRAME_MAX - AQ_SKB_ALIGN) {
skb = build_skb(aq_buf_vaddr(&buff->rxdata), AQ_CFG_RX_FRAME_MAX);
} else {
skb = napi_alloc_skb(napi, AQ_CFG_RX_HDR_SIZE);
There is a significant difference between the SKB produced by these
2 code paths. When napi_alloc_skb creates an SKB, there is a certain
amount of headroom reserved. However, this is not done in the
build_skb codepath.
As the hardware buffer that build_skb is built around does not
handle the presence of the SKB header, this code path is being
removed and the napi_alloc_skb path will always be used. This code
path does have to copy the packet header into the SKB, but it adds
the packet data as a frag.
Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Lincoln Ramsay <lincoln.ramsay@opengear.com>
Link: https://lore.kernel.org/r/MWHPR1001MB23184F3EAFA413E0D1910EC9E8FC0@MWHPR1001MB2318.namprd10.prod.outlook.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Prevent VFs from resetting when PF driver is being unloaded:
- introduce new pf state: __I40E_VF_RESETS_DISABLED;
- check if pf state has __I40E_VF_RESETS_DISABLED state set,
if so, disable any further VFLR event notifications;
- when i40e_remove (rmmod i40e) is called, disable any resets on
the VFs;
Previously if there were bare-metal VFs passing traffic and PF
driver was removed, there was a possibility of VFs triggering a Tx
timeout right before iavf_remove. This was causing iavf_close to
not be called because there is a check in the beginning of iavf_remove
that bails out early if adapter->state < IAVF_DOWN_PENDING. This
makes it so some resources do not get cleaned up.
Fixes: 6a9ddb36eeb8 ("i40e: disable IOV before freeing resources")
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20201120180640.3654474-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.10
First set of fixes for v5.10. One fix for iwlwifi kernel panic, others
less notable.
rtw88
* fix a bogus test found by clang
iwlwifi
* fix long memory reads causing soft lockup warnings
* fix kernel panic during Channel Switch Announcement (CSA)
* other smaller fixes
MAINTAINERS
* email address updates
* tag 'wireless-drivers-2020-11-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers:
iwlwifi: mvm: fix kernel panic in case of assert during CSA
iwlwifi: pcie: set LTR to avoid completion timeout
iwlwifi: mvm: write queue_sync_state only for sync
iwlwifi: mvm: properly cancel a session protection for P2P
iwlwifi: mvm: use the HOT_SPOT_CMD to cancel an AUX ROC
iwlwifi: sta: set max HE max A-MPDU according to HE capa
MAINTAINERS: update maintainers list for Cypress
MAINTAINERS: update Yan-Hsuan's email address
iwlwifi: pcie: limit memory read spin time
rtw88: fix fw_fifo_addr check
====================
Link: https://lore.kernel.org/r/20201123161037.C11D1C43460@smtp.codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Sometimes it takes longer than 5 seconds (watchdog timeout) to complete
failover, migration, and other resets. In stead of scheduling another
timeout reset, we wait for the current one to complete.
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 61d3e1d9bc2a ("ibmvnic: Remove netdev notify for failover resets")
excluded the failover case for notify call because it said
netdev_notify_peers() can cause network traffic to stall or halt.
Current testing does not show network traffic stall
or halt because of the notify call for failover event.
netdev_notify_peers may be used when a device wants to inform the
rest of the network about some sort of a reconfiguration
such as failover or migration.
It is unnecessary to call that in other events like
FATAL, NON_FATAL, CHANGE_PARAM, and TIMEOUT resets
since in those scenarios the hardware does not change.
If the driver must do a hard reset, it is necessary to notify peers.
Fixes: 61d3e1d9bc2a ("ibmvnic: Remove netdev notify for failover resets")
Suggested-by: Brian King <brking@linux.vnet.ibm.com>
Suggested-by: Pradeep Satyanarayana <pradeeps@linux.vnet.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When netdev_notify_peers was substituted in
commit 986103e7920c ("net/ibmvnic: Fix RTNL deadlock during device reset"),
call_netdevice_notifiers(NETDEV_RESEND_IGMP, dev) was missed.
Fix it now.
Fixes: 986103e7920c ("net/ibmvnic: Fix RTNL deadlock during device reset")
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Reviewed-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tun only checks the file O_NONBLOCK flag, but it should also be checking
the iocb IOCB_NOWAIT flag. Any fops using ->read/write_iter() should check
both, otherwise it breaks users that correctly expect O_NONBLOCK semantics
if IOCB_NOWAIT is set.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/e9451860-96cc-c7c7-47b8-fe42cadd5f4c@kernel.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting with iOS 14 released in September 2020, connectivity using the
personal hotspot USB tethering function of iOS devices is broken.
Communication between the host and the device (for example ICMP traffic
or DNS resolution using the DNS service running in the device itself)
works fine, but communication to endpoints further away doesn't work.
Investigation on the matter shows that no UDP and ICMP traffic from the
tethered host is reaching the Internet at all. For TCP traffic there are
exchanges between tethered host and server but packets are modified in
transit leading to impossible communication.
After some trials Matti Vuorela discovered that reducing the URB buffer
size by two bytes restored the previous behavior. While a better
solution might exist to fix the issue, since the protocol is not
publicly documented and considering the small size of the fix, let's do
that.
Tested-by: Matti Vuorela <matti.vuorela@bitfactor.fi>
Signed-off-by: Yves-Alexis Perez <corsac@corsac.net>
Link: https://lore.kernel.org/linux-usb/CAAn0qaXmysJ9vx3ZEMkViv_B19ju-_ExN8Yn_uSefxpjS6g4Lw@mail.gmail.com/
Link: https://github.com/libimobiledevice/libimobiledevice/issues/1038
Link: https://lore.kernel.org/r/20201119172439.94988-1-corsac@corsac.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After commit 9d2e5e9eeb59 ("cxgb4/ch_ktls: decrypted bit is not enough")
whenever CONFIG_TLS=m and CONFIG_CHELSIO_T4=y, the following build
failure occurs:
ld: drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.o: in function
`cxgb_select_queue':
cxgb4_main.c:(.text+0x2dac): undefined reference to `tls_validate_xmit_skb'
Fix this by ensuring that if TLS is set to be a module, CHELSIO_T4 will
also be compiled as a module. As otherwise the cxgb4 driver will not be
able to access TLS' symbols.
Fixes: 9d2e5e9eeb59 ("cxgb4/ch_ktls: decrypted bit is not enough")
Signed-off-by: Tom Seewald <tseewald@gmail.com>
Link: https://lore.kernel.org/r/20201120192528.615-1-tseewald@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
syzkaller found that with CONFIG_DEBUG_KOBJECT_RELEASE=y, releasing a
struct slave device could result in the following splat:
kobject: 'bonding_slave' (00000000cecdd4fe): kobject_release, parent 0000000074ceb2b2 (delayed 1000)
bond0 (unregistering): (slave bond_slave_1): Releasing backup interface
------------[ cut here ]------------
ODEBUG: free active (active state 0) object type: timer_list hint: workqueue_select_cpu_near kernel/workqueue.c:1549 [inline]
ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x98 kernel/workqueue.c:1600
WARNING: CPU: 1 PID: 842 at lib/debugobjects.c:485 debug_print_object+0x180/0x240 lib/debugobjects.c:485
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 842 Comm: kworker/u4:4 Tainted: G S 5.9.0-rc8+ #96
Hardware name: linux,dummy-virt (DT)
Workqueue: netns cleanup_net
Call trace:
dump_backtrace+0x0/0x4d8 include/linux/bitmap.h:239
show_stack+0x34/0x48 arch/arm64/kernel/traps.c:142
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x174/0x1f8 lib/dump_stack.c:118
panic+0x360/0x7a0 kernel/panic.c:231
__warn+0x244/0x2ec kernel/panic.c:600
report_bug+0x240/0x398 lib/bug.c:198
bug_handler+0x50/0xc0 arch/arm64/kernel/traps.c:974
call_break_hook+0x160/0x1d8 arch/arm64/kernel/debug-monitors.c:322
brk_handler+0x30/0xc0 arch/arm64/kernel/debug-monitors.c:329
do_debug_exception+0x184/0x340 arch/arm64/mm/fault.c:864
el1_dbg+0x48/0xb0 arch/arm64/kernel/entry-common.c:65
el1_sync_handler+0x170/0x1c8 arch/arm64/kernel/entry-common.c:93
el1_sync+0x80/0x100 arch/arm64/kernel/entry.S:594
debug_print_object+0x180/0x240 lib/debugobjects.c:485
__debug_check_no_obj_freed lib/debugobjects.c:967 [inline]
debug_check_no_obj_freed+0x200/0x430 lib/debugobjects.c:998
slab_free_hook mm/slub.c:1536 [inline]
slab_free_freelist_hook+0x190/0x210 mm/slub.c:1577
slab_free mm/slub.c:3138 [inline]
kfree+0x13c/0x460 mm/slub.c:4119
bond_free_slave+0x8c/0xf8 drivers/net/bonding/bond_main.c:1492
__bond_release_one+0xe0c/0xec8 drivers/net/bonding/bond_main.c:2190
bond_slave_netdev_event drivers/net/bonding/bond_main.c:3309 [inline]
bond_netdev_event+0x8f0/0xa70 drivers/net/bonding/bond_main.c:3420
notifier_call_chain+0xf0/0x200 kernel/notifier.c:83
__raw_notifier_call_chain kernel/notifier.c:361 [inline]
raw_notifier_call_chain+0x44/0x58 kernel/notifier.c:368
call_netdevice_notifiers_info+0xbc/0x150 net/core/dev.c:2033
call_netdevice_notifiers_extack net/core/dev.c:2045 [inline]
call_netdevice_notifiers net/core/dev.c:2059 [inline]
rollback_registered_many+0x6a4/0xec0 net/core/dev.c:9347
unregister_netdevice_many.part.0+0x2c/0x1c0 net/core/dev.c:10509
unregister_netdevice_many net/core/dev.c:10508 [inline]
default_device_exit_batch+0x294/0x338 net/core/dev.c:10992
ops_exit_list.isra.0+0xec/0x150 net/core/net_namespace.c:189
cleanup_net+0x44c/0x888 net/core/net_namespace.c:603
process_one_work+0x96c/0x18c0 kernel/workqueue.c:2269
worker_thread+0x3f0/0xc30 kernel/workqueue.c:2415
kthread+0x390/0x498 kernel/kthread.c:292
ret_from_fork+0x10/0x18 arch/arm64/kernel/entry.S:925
This is a potential use-after-free if the sysfs nodes are being accessed
whilst removing the struct slave, so wait for the object destruction to
complete before freeing the struct slave itself.
Fixes: 07699f9a7c8d ("bonding: add sysfs /slave dir for bond slave devices.")
Fixes: a068aab42258 ("bonding: Fix reference count leak in bond_sysfs_slave_add.")
Cc: Qiushi Wu <wu000273@umn.edu>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jamie Iles <jamie@nuviainc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201120142827.879226-1-jamie@nuviainc.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When qeth_iqd_tx_complete() detects that a TX buffer requires additional
async completion via QAOB, it might fail to replace the queue entry's
metadata (and ends up triggering recovery).
Assume now that the device gets torn down, overruling the recovery.
If the QAOB notification then arrives before the tear down has
sufficiently progressed, the buffer state is changed to
QETH_QDIO_BUF_HANDLED_DELAYED by qeth_qdio_handle_aob().
The tear down code calls qeth_drain_output_queue(), where
qeth_cleanup_handled_pending() will then attempt to replace such a
buffer _again_. If it succeeds this time, the buffer ends up dangling in
its replacement's ->next_pending list ... where it will never be freed,
since there's no further call to qeth_cleanup_handled_pending().
But the second attempt isn't actually needed, we can simply leave the
buffer on the queue and re-use it after a potential recovery has
completed. The qeth_clear_output_buffer() in qeth_drain_output_queue()
will ensure that it's in a clean state again.
Fixes: 72861ae792c2 ("qeth: recovery through asynchronous delivery")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The two expected notification sequences are
1. TX_NOTIFY_PENDING with a subsequent TX_NOTIFY_DELAYED_*, when
our TX completion code first observed the pending TX and the QAOB
then completes at a later time; or
2. TX_NOTIFY_OK, when qeth_qdio_handle_aob() picked up the QAOB
completion before our TX completion code even noticed that the TX
was pending.
But as qeth_iqd_tx_complete() and qeth_qdio_handle_aob() can run
concurrently, we may end up with a race that results in a sequence of
TX_NOTIFY_DELAYED_* followed by TX_NOTIFY_PENDING. Which would confuse
the af_iucv code in its tracking of pending transmits.
Rework the notification code, so that qeth_qdio_handle_aob() defers its
notification if the TX completion code is still active.
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Calling into socket code is ugly already, at least check whether we are
dealing with the expected sk_family. Only looking at skb->protocol is
bound to cause troubles (consider eg. af_packet).
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove workaround that supported early hardware implementations
of PNSO OC3. Rely on the 'enarf' feature bit instead.
Fixes: fa115adff2c1 ("s390/qeth: Detect PNSO OC3 capability")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
[jwi: use logical instead of bit-wise AND]
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Explicitly enable the FSL_XGMAC_MDIO Kconfig option in order to have
MDIO access to internal and external PHYs.
Fixes: 719479230893 ("dpaa2-eth: add MAC/PHY support through phylink")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20201119145106.712761-1-ciorneiioana@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
SMT entry is allocated only when loopback Source MAC
rewriting is requested. Accessing SMT entry for non
smac rewrite cases results in kernel panic.
Fix the panic caused by non smac rewrite
Fixes: 937d84205884 ("cxgb4: set up filter action after rewrites")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Link: https://lore.kernel.org/r/20201118143213.13319-1-rajur@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jump to init_err_release to cleanup. bnxt_unmap_bars() will also be
called but it will do nothing if the BARs are not mapped yet.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1605858271-8209-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Link: https://lore.kernel.org/r/1605792621-6268-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: c213eae8d3cd ("bnxt_en: Improve VF/PF link change logic.")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Link: https://lore.kernel.org/r/1605701851-20270-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.10-rc5, including fixes from the WiFi
(mac80211), can and bpf (including the strncpy_from_user fix).
Current release - regressions:
- mac80211: fix memory leak of filtered powersave frames
- mac80211: free sta in sta_info_insert_finish() on errors to avoid
sleeping in atomic context
- netlabel: fix an uninitialized variable warning added in -rc4
Previous release - regressions:
- vsock: forward all packets to the host when no H2G is registered,
un-breaking AWS Nitro Enclaves
- net: Exempt multicast addresses from five-second neighbor lifetime
requirement, decreasing the chances neighbor tables fill up
- net/tls: fix corrupted data in recvmsg
- qed: fix ILT configuration of SRC block
- can: m_can: process interrupt only when not runtime suspended
Previous release - always broken:
- page_frag: Recover from memory pressure by not recycling pages
allocating from the reserves
- strncpy_from_user: Mask out bytes after NUL terminator
- ip_tunnels: Set tunnel option flag only when tunnel metadata is
present, always setting it confuses Open vSwitch
- bpf, sockmap:
- Fix partial copy_page_to_iter so progress can still be made
- Fix socket memory accounting and obeying SO_RCVBUF
- net: Have netpoll bring-up DSA management interface
- net: bridge: add missing counters to ndo_get_stats64 callback
- tcp: brr: only postpone PROBE_RTT if RTT is < current min_rtt
- enetc: Workaround MDIO register access HW bug
- net/ncsi: move netlink family registration to a subsystem init,
instead of tying it to driver probe
- net: ftgmac100: unregister NC-SI when removing driver to avoid
crash
- lan743x:
- prevent interrupt storm on open
- fix freeing skbs in the wrong context
- net/mlx5e: Fix socket refcount leak on kTLS RX resync
- net: dsa: mv88e6xxx: Avoid VLAN database corruption on 6097
- fix 21 unset return codes and other mistakes on error paths, mostly
detected by the Hulk Robot"
* tag 'net-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (115 commits)
fail_function: Remove a redundant mutex unlock
selftest/bpf: Test bpf_probe_read_user_str() strips trailing bytes after NUL
lib/strncpy_from_user.c: Mask out bytes after NUL terminator.
net/smc: fix direct access to ib_gid_addr->ndev in smc_ib_determine_gid()
net/smc: fix matching of existing link groups
ipv6: Remove dependency of ipv6_frag_thdr_truncated on ipv6 module
libbpf: Fix VERSIONED_SYM_COUNT number parsing
net/mlx4_core: Fix init_hca fields offset
atm: nicstar: Unmap DMA on send error
page_frag: Recover from memory pressure
net: dsa: mv88e6xxx: Wait for EEPROM done after HW reset
mlxsw: core: Use variable timeout for EMAD retries
mlxsw: Fix firmware flashing
net: Have netpoll bring-up DSA management interface
atl1e: fix error return code in atl1e_probe()
atl1c: fix error return code in atl1c_probe()
ah6: fix error return code in ah6_input()
net: usb: qmi_wwan: Set DTR quirk for MR400
can: m_can: process interrupt only when not runtime suspended
can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery
...
|
|
Pull rdma fixes from Jason Gunthorpe:
"The last two weeks have been quiet here, just the usual smattering of
long standing bug fixes.
A collection of error case bug fixes:
- Improper nesting of spinlock types in cm
- Missing error codes and kfree()
- Ensure dma_virt_ops users have the right kconfig symbols to work
properly
- Compilation failure of tools/testing"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
tools/testing/scatterlist: Fix test to compile and run
IB/hfi1: Fix error return code in hfi1_init_dd()
RMDA/sw: Don't allow drivers using dma_virt_ops on highmem configs
RDMA/pvrdma: Fix missing kfree() in pvrdma_register_device()
RDMA/cm: Make the local_id_table xarray non-irq
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix recent regression in the APEI code and initialization issue
in the ACPI fan driver.
Specifics:
- Make the APEI code avoid attempts to obtain logical addresses for
registers located in the I/O address space to fix initialization
issues (Aili Yao)
- Fix sysfs attribute initialization in the ACPI fan driver (Guenter
Roeck)"
* tag 'acpi-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI, APEI, Fix error return value in apei_map_generic_address()
ACPI: fan: Initialize performance state sysfs attribute
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix two issues in ARM cpufreq drivers and one cpuidle driver
issue.
Specifics:
- Add missing RCU_NONIDLE() annotations to the Tegra cpuidle driver
(Dmitry Osipenko)
- Fix boot frequency computation in the tegra186 cpufreq driver (Jon
Hunter)
- Make the SCMI cpufreq driver register a dummy clock provider to
avoid OPP addition failures (Sudeep Holla)"
* tag 'pm-5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scmi: Fix OPP addition failure with a dummy clock provider
cpufreq: tegra186: Fix get frequency callback
cpuidle: tegra: Annotate tegra_pm_set_cpu_in_lp2() with RCU_NONIDLE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"This is a relatively large set of fixes, the bulk of it being a series
from Lukas Wunner which fixes confusion with the lifetime of driver
data allocated along with the SPI controller structure that's been
created as part of the conversion to devm APIs.
The simplest fix, explained in detail in Lukas' commit message, is to
move to a devm_ function for allocation of the controller and hence
driver data in order to push the free of that after anything tries to
reference the driver data in the remove path. This results in a
relatively large diff due to the addition of a new function but isn't
particularly complex.
There's also a fix from Sven van Asbroeck which fixes yet more fallout
from the conflicts between the various different places one can
configure the polarity of GPIOs in modern systems.
Otherwise everything is fairly small and driver specific"
* tag 'spi-fix-v5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: npcm-fiu: Don't leak SPI master in probe error path
spi: dw: Set transfer handler before unmasking the IRQs
spi: cadence-quadspi: Fix error return code in cqspi_probe
spi: bcm2835aux: Restore err assignment in bcm2835aux_spi_probe
spi: lpspi: Fix use-after-free on unbind
spi: bcm-qspi: Fix use-after-free on unbind
spi: bcm2835aux: Fix use-after-free on unbind
spi: bcm2835: Fix use-after-free on unbind
spi: Introduce device-managed SPI controller allocation
spi: fsi: Fix transfer returning without finalizing message
spi: fix client driver breakages when using GPIO descriptors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Mostly core fixes here, one set from Michał Mirosław which cleans up
some issues introduced as part of the coupled regulators work, one
memory leak during probe and two due to regulators which have an input
supply name and regulator name which are identical, which is very
unusual.
There's also a fix for our handling of the similarly unusual case
where we can't determine if a regulator is enabled during boot"
* tag 'regulator-fix-v5.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: ti-abb: Fix array out of bound read access on the first transition
regulator: workaround self-referent regulators
regulator: avoid resolve_supply() infinite recursion
regulator: fix memory leak with repeated set_machine_constraints()
regulator: pfuze100: limit pfuze-support-disable-sw to pfuze{100,200}
regulator: core: don't disable regulator if is_enabled return error.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fix from Daniel Lezcano:
"Disable the CPU PM notifier for OMAP4430 for suspend in order to
prevent wrong temperature leading to a critical shutdown (Peter
Ujfalusi)"
* tag 'thermal-v5.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: ti-soc-thermal: Disable the CPU PM notifier for OMAP4430
|
|
* acpi-fan:
ACPI: fan: Initialize performance state sysfs attribute
|
|
* pm-cpuidle:
cpuidle: tegra: Annotate tegra_pm_set_cpu_in_lp2() with RCU_NONIDLE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2020-11-18
Jimmy Assarsson provides two patches for the kvaser_pciefd and kvaser_usb
drivers, where the can_bittiming_const are fixed.
The next patch is by me and fixes an erroneous flexcan_transceiver_enable()
during bus-off recovery in the flexcan driver.
Jarkko Nikula's patch for the m_can driver fixes the IRQ handler to only
process the interrupts if the device is not suspended.
* tag 'linux-can-fixes-for-5.10-20201118' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: m_can: process interrupt only when not runtime suspended
can: flexcan: flexcan_chip_start(): fix erroneous flexcan_transceiver_enable() during bus-off recovery
can: kvaser_usb: kvaser_usb_hydra: Fix KCAN bittiming limits
can: kvaser_pciefd: Fix KCAN bittiming limits
====================
Link: https://lore.kernel.org/r/20201118160414.2731659-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Slave function read the following capabilities from the wrong offset:
1. log_mc_entry_sz
2. fs_log_entry_sz
3. log_mc_hash_sz
Fix that by adjusting these capabilities offset to match firmware
layout.
Due to the wrong offset read, the following issues might occur:
1+2. Negative value reported at max_mcast_qp_attach.
3. Driver to init FW with multicast hash size of zero.
Fixes: a40ded604365 ("net/mlx4_core: Add masking for a few queries on HCA caps")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20201118081922.553-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2020-11-17
This series introduces some fixes to mlx5 driver.
* tag 'mlx5-fixes-2020-11-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: fix error return code in mlx5e_tc_nic_init()
net/mlx5: E-Switch, Fail mlx5_esw_modify_vport_rate if qos disabled
net/mlx5: Disable QoS when min_rates on all VFs are zero
net/mlx5: Clear bw_share upon VF disable
net/mlx5: Add handling of port type in rule deletion
net/mlx5e: Fix check if netdev is bond slave
net/mlx5e: Fix IPsec packet drop by mlx5e_tc_update_skb
net/mlx5e: Set IPsec WAs only in IP's non checksum partial case.
net/mlx5e: Fix refcount leak on kTLS RX resync
====================
Link: https://lore.kernel.org/r/20201117195702.386113-1-saeedm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The `skb' is mapped for DMA in ns_send() but does not unmap DMA in case
push_scqe() fails to submit the `skb'. The memory of the `skb' is
released so only the DMA mapping is leaking.
Unmap the DMA mapping in case push_scqe() failed.
Fixes: 864a3ff635fa7 ("atm: [nicstar] remove virt_to_bus() and support 64-bit platforms")
Cc: Chas Williams <3chas3@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the switch is hardware reset, it reads the contents of the
EEPROM. This can contain instructions for programming values into
registers and to perform waits between such programming. Reading the
EEPROM can take longer than the 100ms mv88e6xxx_hardware_reset() waits
after deasserting the reset GPIO. So poll the EEPROM done bit to
ensure it is complete.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ruslan Sushko <rus@sushko.dev>
Link: https://lore.kernel.org/r/20201116164301.977661-1-rus@sushko.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
