| Age | Commit message (Collapse) | Author |
|---|
|
Raise the config max for lpfc_fcp_mq_threshold variable to 256.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
CC: Hannes Reinecke <hare@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Family 16h Model 30h SMBus controller needs the same port selection fix
as described and fixed in commit 0fe16195f891 ("i2c: piix4: Fix SMBus port
selection for AMD Family 17h chips")
commit 6befa3fde65f ("i2c: piix4: Support alternative port selection
register") also fixed the port selection for Hudson2, but unfortunately
this is not the exact same device and the AMD naming and PCI Device IDs
aren't particularly helpful here.
The SMBus port selection register is common to the following Families
and models, as documented in AMD's publicly available BIOS and Kernel
Developer Guides:
50742 - Family 15h Model 60h-6Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
55072 - Family 15h Model 70h-7Fh (PCI_DEVICE_ID_AMD_KERNCZ_SMBUS)
52740 - Family 16h Model 30h-3Fh (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS)
The Hudson2 PCI Device ID (PCI_DEVICE_ID_AMD_HUDSON2_SMBUS) is shared
between Bolton FCH and Family 16h Model 30h, but the location of the
SmBus0Sel port selection bits are different:
51192 - Bolton Register Reference Guide
We distinguish between Bolton and Family 16h Model 30h using the PCI
Revision ID:
Bolton is device 0x780b, revision 0x15
Family 16h Model 30h is device 0x780b, revision 0x1F
Family 15h Model 60h and 70h are both device 0x790b, revision 0x4A.
The following additional public AMD BKDG documents were checked and do
not share the same port selection register:
42301 - Family 15h Model 00h-0Fh doesn't mention any
42300 - Family 15h Model 10h-1Fh doesn't mention any
49125 - Family 15h Model 30h-3Fh doesn't mention any
48751 - Family 16h Model 00h-0Fh uses the previously supported
index register SB800_PIIX4_PORT_IDX_ALT at 0x2e
Signed-off-by: Andrew Cooks <andrew.cooks@opengear.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org [v4.6+]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Make sure interrupt handler i2c_dw_irq_handler_slave() has finished
before clearing the the dev->slave pointer in i2c_dw_unreg_slave().
There is possibility for a race if i2c_dw_irq_handler_slave() is running
on another CPU while clearing the dev->slave pointer.
Reported-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
check_acpi_smo88xx_device() utilizes acpi_get_object_info() which in its turn
allocates a buffer. User is responsible to clean allocated resources. The last
has been missed in the original code. Fix it here.
While here, replace !ACPI_SUCCESS() with ACPI_FAILURE().
Fixes: 19b07cb4a187 ("i2c: i801: Register optional lis3lv02d I2C device on Dell machines")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We are moving towards returning ERR_PTRs when i2c_new_*_device() calls
fail. Make sure its counterpart for unregistering handles ERR_PTRs as
well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd fix from Miquel Raynal:
"Add a 'depends on' in the core Hyperbus Kconfig entry to avoid build
errors"
* tag 'mtd/fixes-for-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: hyperbus: fix dependency and build error
|
|
The move of the IXP4xx SoC drivers exposed their config options on all
platforms.
Fix this by wrapping them inside an ARCH_IXP4XX or COMPILE_TEST block.
Link: https://lore.kernel.org/r/20190823090352.12243-1-linus.walleij@linaro.org
Fixes: fcf2d8978cd538a5 ("ARM: ixp4xx: Move NPE and QMGR to drivers/soc")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
arm/fixes
Hisilicon fixes for v5.3-rc
- Fixed RCU usage in logical PIO
- Added a function to unregister a logical PIO range in logical PIO
to support the fixes in the hisi-lpc driver
- Fixed and optimized hisi-lpc driver to avoid potential use-after-free
and driver unbind crash
* tag 'hisi-fixes-for-5.3' of git://github.com/hisilicon/linux-hisi:
bus: hisi_lpc: Add .remove method to avoid driver unbind crash
bus: hisi_lpc: Unregister logical PIO range to avoid potential use-after-free
lib: logic_pio: Add logic_pio_unregister_range()
lib: logic_pio: Avoid possible overlap for unregistering regions
lib: logic_pio: Fix RCU usage
Link: https://lore.kernel.org/r/5D562335.7000902@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
lib/devres.c, which implements devm_ioremap_resource(), is only built
when CONFIG_HAS_IOMEM is set/enabled, so MTD_HYPERBUS should depend
on HAS_IOMEM. Fixes a build error and a Kconfig warning (as seen on
UML builds):
WARNING: unmet direct dependencies detected for MTD_COMPLEX_MAPPINGS
Depends on [n]: MTD [=m] && HAS_IOMEM [=n]
Selected by [m]:
- MTD_HYPERBUS [=m] && MTD [=m]
ERROR: "devm_ioremap_resource" [drivers/mtd/hyperbus/hyperbus-core.ko] undefined!
Fixes: dcc7d3446a0f ("mtd: Add support for HyperBus memory devices")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-mtd@lists.infradead.org
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The ingenic driver supports DPI panels only at the moment, so hardcode
their type to DPI instead of Unknown.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20190823212353.29369-1-laurent.pinchart@ideasonboard.com
# *** extracted tags ***
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
|
|
A similar workaround for the suspend/resume problem is needed for yet
another ASUS machines, P6X models. Like the previous fix, the BIOS
doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_*
entries are used instead.
Reported-and-tested-by: SteveM <swm@swm1.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent code changes to NFP allowed the offload of neighbour entries to FW
when the next hop device was an internal port. This allows for offload of
tunnel encap when the end-point IP address is applied to such a port.
Unfortunately, the neighbour event handler still rejects events that are
not associated with a repr dev and so the firmware neighbour table may get
out of sync for internal ports.
Fix this by allowing internal port neighbour events to be correctly
processed.
Fixes: 45756dfedab5 ("nfp: flower: allow tunnels to output to internal port")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Internal port TC offload is implemented through user-space applications
(such as OvS) by adding filters at egress via TC clsact qdiscs. Indirect
block offload support in the NFP driver accepts both ingress qdisc binds
and egress binds if the device is an internal port. However, clsact sends
bind notification for both ingress and egress block binds which can lead
to the driver registering multiple callbacks and receiving multiple
notifications of new filters.
Fix this by rejecting ingress block bind callbacks when the port is
internal and only adding filter callbacks for egress binds.
Fixes: 4d12ba42787b ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unnecessary use of netif_napi_del. This also avoids to call
napi_disable() after netif_napi_del().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 0ee1f4734967af8321ecebaf9c74221ace34f2d5.
The commit 0ee1f4734967 ("r8152: napi hangup fix after
disconnect") adds a check about RTL8152_UNPLUG to determine
if calling napi_disable() is invalid in rtl8152_close(),
when rtl8152_disconnect() is called. This avoids to use
napi_disable() after calling netif_napi_del().
Howver, commit ffa9fec30ca0 ("r8152: set RTL8152_UNPLUG
only for real disconnection") causes that RTL8152_UNPLUG
is not always set when calling rtl8152_disconnect().
Therefore, I have to revert commit 0ee1f4734967 ("r8152:
napi hangup fix after disconnect"), first. And submit
another patch to fix it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the ibmvnic driver will not schedule device resets
if the device is being removed, but does not check the device
state before the reset is actually processed. This leads to a race
where a reset is scheduled with a valid device state but is
processed after the driver has been removed, resulting in an oops.
Fix this by checking the device state before processing a queued
reset event.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the General Purpose Amlogic Everything-Else Power controller,
with the first support for G12A and SM1 SoCs dedicated to the VPU, PCIe,
USB, NNA, GE2D and Ethernet Power Domains.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Update the compatibility string for SiFive FU540-C000 as per the new
string updated in the binding doc.
Reference:
https://lore.kernel.org/netdev/CAJ2_jOFEVZQat0Yprg4hem4jRrqkB72FKSeQj4p8P5KA-+rgww@mail.gmail.com/
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Paul Walmsley <paul.walmsley@sifive.com>
Tested-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scom driver currently fails out of operations if certain system
errors are flagged in the status register; system checkstop, special
attention, or recoverable error. These errors won't impact the ability
of the scom engine to perform operations, so the driver should continue
under these conditions.
Also, don't do a PIB reset for these conditions, since it won't help.
Fixes: 6b293258cded ("fsi: scom: Major overhaul")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20190827041249.13381-1-jk@ozlabs.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The compaction code already marks pages as offline when it enqueues
pages in the ballooned page list, and removes the mapping when the pages
are removed from the list. VMware balloon also updates the flags,
instead of letting the balloon-compaction logic handle it, which causes
the assertion VM_BUG_ON_PAGE(!PageOffline(page)) to fire, when
__ClearPageOffline is called the second time. This causes the following
crash.
[ 487.104520] kernel BUG at include/linux/page-flags.h:749!
[ 487.106364] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[ 487.107681] CPU: 7 PID: 1106 Comm: kworker/7:3 Not tainted 5.3.0-rc5balloon #227
[ 487.109196] Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 12/12/2018
[ 487.111452] Workqueue: events_freezable vmballoon_work [vmw_balloon]
[ 487.112779] RIP: 0010:vmballoon_release_page_list+0xaa/0x100 [vmw_balloon]
[ 487.114200] Code: fe 48 c1 e7 06 4c 01 c7 8b 47 30 41 89 c1 41 81 e1 00 01 00 f0 41 81 f9 00 00 00 f0 74 d3 48 c7 c6 08 a1 a1 c0 e8 06 0d e7 ea <0f> 0b 44 89 f6 4c 89 c7 e8 49 9c e9 ea 49 8d 75 08 49 8b 45 08 4d
[ 487.118033] RSP: 0018:ffffb82f012bbc98 EFLAGS: 00010246
[ 487.119135] RAX: 0000000000000037 RBX: 0000000000000001 RCX: 0000000000000006
[ 487.120601] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9a85b6bd7620
[ 487.122071] RBP: ffffb82f012bbcc0 R08: 0000000000000001 R09: 0000000000000000
[ 487.123536] R10: 0000000000000000 R11: 0000000000000000 R12: ffffb82f012bbd00
[ 487.125002] R13: ffffe97f4598d9c0 R14: 0000000000000000 R15: ffffb82f012bbd34
[ 487.126463] FS: 0000000000000000(0000) GS:ffff9a85b6bc0000(0000) knlGS:0000000000000000
[ 487.128110] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 487.129316] CR2: 00007ffe6e413ea0 CR3: 0000000230b18001 CR4: 00000000003606e0
[ 487.130812] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 487.132283] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 487.133749] Call Trace:
[ 487.134333] vmballoon_deflate+0x22c/0x390 [vmw_balloon]
[ 487.135468] vmballoon_work+0x6e7/0x913 [vmw_balloon]
[ 487.136711] ? process_one_work+0x21a/0x5e0
[ 487.138581] process_one_work+0x298/0x5e0
[ 487.139926] ? vmballoon_migratepage+0x310/0x310 [vmw_balloon]
[ 487.141610] ? process_one_work+0x298/0x5e0
[ 487.143053] worker_thread+0x41/0x400
[ 487.144389] kthread+0x12b/0x150
[ 487.145582] ? process_one_work+0x5e0/0x5e0
[ 487.146937] ? kthread_create_on_node+0x60/0x60
[ 487.148637] ret_from_fork+0x3a/0x50
Fix it by updating the PageOffline indication only when a 2MB page is
enqueued and dequeued. The 4KB pages will be handled correctly by the
balloon compaction logic.
Fixes: 83a8afa72e9c ("vmw_balloon: Compaction support")
Cc: David Hildenbrand <david@redhat.com>
Reported-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Link: https://lore.kernel.org/r/20190820160121.452-1-namit@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Francois reported that VMware balloon gets stuck after a balloon reset,
when the VMCI doorbell is removed. A similar error can occur when the
balloon driver is removed with the following splat:
[ 1088.622000] INFO: task modprobe:3565 blocked for more than 120 seconds.
[ 1088.622035] Tainted: G W 5.2.0 #4
[ 1088.622087] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1088.622205] modprobe D 0 3565 1450 0x00000000
[ 1088.622210] Call Trace:
[ 1088.622246] __schedule+0x2a8/0x690
[ 1088.622248] schedule+0x2d/0x90
[ 1088.622250] schedule_timeout+0x1d3/0x2f0
[ 1088.622252] wait_for_completion+0xba/0x140
[ 1088.622320] ? wake_up_q+0x80/0x80
[ 1088.622370] vmci_resource_remove+0xb9/0xc0 [vmw_vmci]
[ 1088.622373] vmci_doorbell_destroy+0x9e/0xd0 [vmw_vmci]
[ 1088.622379] vmballoon_vmci_cleanup+0x6e/0xf0 [vmw_balloon]
[ 1088.622381] vmballoon_exit+0x18/0xcc8 [vmw_balloon]
[ 1088.622394] __x64_sys_delete_module+0x146/0x280
[ 1088.622408] do_syscall_64+0x5a/0x130
[ 1088.622410] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 1088.622415] RIP: 0033:0x7f54f62791b7
[ 1088.622421] Code: Bad RIP value.
[ 1088.622421] RSP: 002b:00007fff2a949008 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
[ 1088.622426] RAX: ffffffffffffffda RBX: 000055dff8b55d00 RCX: 00007f54f62791b7
[ 1088.622426] RDX: 0000000000000000 RSI: 0000000000000800 RDI: 000055dff8b55d68
[ 1088.622427] RBP: 000055dff8b55d00 R08: 00007fff2a947fb1 R09: 0000000000000000
[ 1088.622427] R10: 00007f54f62f5cc0 R11: 0000000000000206 R12: 000055dff8b55d68
[ 1088.622428] R13: 0000000000000001 R14: 000055dff8b55d68 R15: 00007fff2a94a3f0
The cause for the bug is that when the "delayed" doorbell is invoked, it
takes a reference on the doorbell entry and schedules work that is
supposed to run the appropriate code and drop the doorbell entry
reference. The code ignores the fact that if the work is already queued,
it will not be scheduled to run one more time. As a result one of the
references would not be dropped. When the code waits for the reference
to get to zero, during balloon reset or module removal, it gets stuck.
Fix it. Drop the reference if schedule_work() indicates that the work is
already queued.
Note that this bug got more apparent (or apparent at all) due to
commit ce664331b248 ("vmw_balloon: VMCI_DOORBELL_SET does not check status").
Fixes: 83e2ec765be03 ("VMCI: doorbell implementation.")
Reported-by: Francois Rigault <rigault.francois@gmail.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Cc: Adit Ranadive <aditr@vmware.com>
Cc: Alexios Zavras <alexios.zavras@intel.com>
Cc: Vishnu DASA <vdasa@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nadav Amit <namit@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Link: https://lore.kernel.org/r/20190820202638.49003-1-namit@vmware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of a disconnect an ongoing flush() has to be made fail.
Nevertheless we cannot be sure that any pending URB has already
finished, so although they will never succeed, they still must
not be touched.
The clean solution for this is to check for WDM_IN_USE
and WDM_DISCONNECTED in flush(). There is no point in ever
clearing WDM_IN_USE, as no further writes make sense.
The issue is as old as the driver.
Fixes: afba937e540c9 ("USB: CDC WDM driver")
Reported-by: syzbot+d232cca6ec42c2edb3fc@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190827103436.21143-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's spelled "renesas", not "renensas".
Due to this typo, RZ/G1M and RZ/G1N were not covered by the check.
Fixes: 2dc240a3308b ("usb: host: xhci: rcar: retire use of xhci_plat_type_is()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20190827125112.12192-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Falcon microcontroller that runs the XUSB firmware and which is
responsible for exposing the XHCI interface can address only 40 bits of
memory. Typically that's not a problem because Tegra devices don't have
enough system memory to exceed those 40 bits.
However, if the ARM SMMU is enable on Tegra186 and later, the addresses
passed to the XUSB controller can be anywhere in the 48-bit IOV address
space of the ARM SMMU. Since the DMA/IOMMU API starts allocating from
the top of the IOVA space, the Falcon microcontroller is not able to
load the firmware successfully.
Fix this by setting the DMA mask to 40 bits, which will force the DMA
API to map the buffer for the firmware to an IOVA that is addressable by
the Falcon.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1566989697-13049-1-git-send-email-nkristam@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Auto-delink requires writing special registers to ums-realtek devices.
Unconditionally enable auto-delink may break newer devices.
So only enable auto-delink by default for the original three IDs,
0x0138, 0x0158 and 0x0159.
Realtek is working on a patch to properly support auto-delink for other
IDs.
BugLink: https://bugs.launchpad.net/bugs/1838886
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190827173450.13572-2-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
auto_delink_en
The option named "auto_delink_en" is a bit misleading, as setting it to
false doesn't really disable auto-delink but let auto-delink be firmware
controlled.
Update the description to reflect the real usage of this parameter.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190827173450.13572-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that the following error is
possible to happen when ohci hardware causes an interruption
and the system is shutting down at the same time.
[ 34.851754] usb 2-1: USB disconnect, device number 2
[ 35.166658] irq 156: nobody cared (try booting with the "irqpoll" option)
[ 35.173445] CPU: 0 PID: 22 Comm: kworker/0:1 Not tainted 5.3.0-rc5 #85
[ 35.179964] Hardware name: Renesas Salvator-X 2nd version board based on r8a77965 (DT)
[ 35.187886] Workqueue: usb_hub_wq hub_event
[ 35.192063] Call trace:
[ 35.194509] dump_backtrace+0x0/0x150
[ 35.198165] show_stack+0x14/0x20
[ 35.201475] dump_stack+0xa0/0xc4
[ 35.204785] __report_bad_irq+0x34/0xe8
[ 35.208614] note_interrupt+0x2cc/0x318
[ 35.212446] handle_irq_event_percpu+0x5c/0x88
[ 35.216883] handle_irq_event+0x48/0x78
[ 35.220712] handle_fasteoi_irq+0xb4/0x188
[ 35.224802] generic_handle_irq+0x24/0x38
[ 35.228804] __handle_domain_irq+0x5c/0xb0
[ 35.232893] gic_handle_irq+0x58/0xa8
[ 35.236548] el1_irq+0xb8/0x180
[ 35.239681] __do_softirq+0x94/0x23c
[ 35.243253] irq_exit+0xd0/0xd8
[ 35.246387] __handle_domain_irq+0x60/0xb0
[ 35.250475] gic_handle_irq+0x58/0xa8
[ 35.254130] el1_irq+0xb8/0x180
[ 35.257268] kernfs_find_ns+0x5c/0x120
[ 35.261010] kernfs_find_and_get_ns+0x3c/0x60
[ 35.265361] sysfs_unmerge_group+0x20/0x68
[ 35.269454] dpm_sysfs_remove+0x2c/0x68
[ 35.273284] device_del+0x80/0x370
[ 35.276683] hid_destroy_device+0x28/0x60
[ 35.280686] usbhid_disconnect+0x4c/0x80
[ 35.284602] usb_unbind_interface+0x6c/0x268
[ 35.288867] device_release_driver_internal+0xe4/0x1b0
[ 35.293998] device_release_driver+0x14/0x20
[ 35.298261] bus_remove_device+0x110/0x128
[ 35.302350] device_del+0x148/0x370
[ 35.305832] usb_disable_device+0x8c/0x1d0
[ 35.309921] usb_disconnect+0xc8/0x2d0
[ 35.313663] hub_event+0x6e0/0x1128
[ 35.317146] process_one_work+0x1e0/0x320
[ 35.321148] worker_thread+0x40/0x450
[ 35.324805] kthread+0x124/0x128
[ 35.328027] ret_from_fork+0x10/0x18
[ 35.331594] handlers:
[ 35.333862] [<0000000079300c1d>] usb_hcd_irq
[ 35.338126] [<0000000079300c1d>] usb_hcd_irq
[ 35.342389] Disabling IRQ #156
ohci_shutdown() disables all the interrupt and rh_state is set to
OHCI_RH_HALTED. In other hand, ohci_irq() is possible to enable
OHCI_INTR_SF and OHCI_INTR_MIE on ohci_irq(). Note that OHCI_INTR_SF
is possible to be set by start_ed_unlink() which is called:
ohci_irq()
-> process_done_list()
-> takeback_td()
-> start_ed_unlink()
So, ohci_irq() has the following condition, the issue happens by
&ohci->regs->intrenable = OHCI_INTR_MIE | OHCI_INTR_SF and
ohci->rh_state = OHCI_RH_HALTED:
/* interrupt for some other device? */
if (ints == 0 || unlikely(ohci->rh_state == OHCI_RH_HALTED))
return IRQ_NOTMINE;
To fix the issue, ohci_shutdown() holds the spin lock while disabling
the interruption and changing the rh_state flag to prevent reenable
the OHCI_INTR_MIE unexpectedly. Note that io_watchdog_func() also
calls the ohci_shutdown() and it already held the spin lock, so that
the patch makes a new function as _ohci_shutdown().
This patch is inspired by a Renesas R-Car Gen3 BSP patch
from Tho Vu.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/1566877910-6020-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using managed device resources in usb_hcd_pci_probe() allows devm usage for
resource subranges, such as the mmio resource for the platform device
created to control host/device mode mux, which is a xhci extended
capability, and sits inside the xhci mmio region.
If managed device resources are not used then "parent" resource
is released before subrange at driver removal as .remove callback is
called before the devres list of resources for this device is walked
and released.
This has been observed with the xhci extended capability driver causing a
use-after-free which is now fixed.
An additional nice benefit is that error handling on driver initialisation
is simplified much.
Signed-off-by: Carsten Schmid <carsten_schmid@mentor.com>
Tested-by: Carsten Schmid <carsten_schmid@mentor.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Fixes: fa31b3cb2ae1 ("xhci: Add Intel extended cap / otg phy mux handling")
Cc: <stable@vger.kernel.org> # v4.19+
Link: https://lore.kernel.org/r/1566569488679.31808@mentor.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There appears to be a typo in the comparison of pdo_max_voltage[i]
with the previous value, currently it is checking against the
array pdo_min_voltage rather than pdo_max_voltage. I believe this
is a typo. Fix this.
Addresses-Coverity: ("Copy-paste error")
Fixes: 5007e1b5db73 ("typec: tcpm: Validate source and sink caps")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20190822135212.10195-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lkdtm/bugs.c:94:2: error: format '%d' expects argument of type 'int', but argument 2 has type 'long unsigned int' [-Werror=format=]
pr_info("Calling function with %d frame size to depth %d ...\n",
^
THREAD_SIZE is defined as a unsigned long, cast CONFIG_FRAME_WARN to
unsigned long as well.
Fixes: 24cccab42c419 ("lkdtm/bugs: Adjust recursion test to avoid elision")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20190827173619.170065-1-rrangel@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add Tiger Lake Point device ID for TGP LP.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190819103210.32748-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds support for the Trace Hub in Tiger Lake PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v4.14+
Link: https://lore.kernel.org/r/20190821074955.3925-5-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for the Trace Hub in another Lewisburg PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: stable@vger.kernel.org # v4.14+
Link: https://lore.kernel.org/r/20190821074955.3925-4-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the error path of stm_source_register_device(), the kfree is
unnecessary, as the put_device() before it ends up calling
stm_source_device_release() to free stm_source_device, leading to
a double free at the outer kfree() call. Remove it.
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: 7bd1d4093c2fa ("stm class: Introduce an abstraction for System Trace Module devices")
Link: https://lore.kernel.org/linux-arm-kernel/1563354988-23826-1-git-send-email-dingxiang@cmss.chinamobile.com/
Cc: stable@vger.kernel.org # v4.4+
Link: https://lore.kernel.org/r/20190821074955.3925-2-alexander.shishkin@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-linus
Moritz writes:
FPGA Manager fixes for 5.3
A single fix for the altera-ps-spi driver that fixes the behavior when
the driver receives -EPROBE_DEFER when trying to obtain a GPIO desc.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
fpga: altera-ps-spi: Fix getting of optional confd gpio
|
|
Yi reported[1] that after commit a3619190d62e ("libnvdimm/pfn: stop
padding pmem namespaces to section alignment"), it was no longer
possible to create a device dax namespace with a 1G alignment. The
reason was that the pmem region was not itself 1G-aligned. The code
happily skips past the first 512M, but fails to account for a now
misaligned end offset (since space was allocated starting at that
misaligned address, and extending for size GBs). Reintroduce
end_trunc, so that the code correctly handles the misaligned end
address. This results in the same behavior as before the introduction
of the offending commit.
[1] https://lists.01.org/pipermail/linux-nvdimm/2019-July/022813.html
Fixes: a3619190d62e ("libnvdimm/pfn: stop padding pmem namespaces ...")
Reported-and-tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Link: https://lore.kernel.org/r/x49ftll8f39.fsf@segfault.boston.devel.redhat.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The de-init routine should be doing the following in order:-
1. Unregister the drm device
2. Shut down the crtcs - failing to do this might cause a connector leakage
See the 'commit 109c4d18e574 ("drm/arm/malidp: Ensure that the crtcs are
shutdown before removing any encoder/connector")'
3. Disable the interrupts
4. Unbind the components
5. Free up DRM mode_config info
Changes from v1:-
1. Re-ordered the header files inclusion
2. Rebased on top of the latest drm-misc-fixes
Signed-off-by:. Ayan Kumar Halder <Ayan.Halder@arm.com>
Reviewed-by: Mihail Atanassov <mihail.atanassov@arm.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Link: https://patchwork.freedesktop.org/patch/327606/
|
|
Walking the address list of an inet6_dev requires
appropriate locking. Since the called function
siw_listen_address() may sleep, we have to use
rtnl_lock() instead of read_lock_bh().
Also introduces sanity checks if we got a device
from in_dev_get() or in6_dev_get().
Reported-by: Bart Van Assche <bvanassche@acm.org>
Fixes: 6c52fdc244b5 ("rdma/siw: connection management")
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20190828130355.22830-1-bmt@zurich.ibm.com
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
AXI filtering is used by events 0x41 and 0x42 to count reads or writes
with an ARID or AWID matching a specified filter. The filter is exposed
to userspace as an (ID, MASK) pair, where each set bit in the mask
causes the corresponding bit in the ID to be ignored when matching
against the ID of memory transactions for the purposes of incrementing
the counter.
For example:
# perf stat -a -e imx8_ddr0/axid-read,axi_mask=0xff,axi_id=0x800/ cmd
will count all read transactions from AXI IDs 0x800 - 0x8ff. If the
'axi_mask' is omitted, then it is treated as 0x0 which means that the
'axi_id' will be matched exactly.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
This converts the BCM2835 SPI master driver to use GPIO
descriptors for chip select handling.
The BCM2835 driver was relying on the core to drive the
CS high/low so very small changes were needed for this
part. If it managed to request the CS from the device tree
node, all is pretty straight forward.
However for native GPIOs this driver has a quite unorthodox
loopback to request some GPIOs from the SoC GPIO chip by
looking it up from the device tree using gpiochip_find()
and then offseting hard into its numberspace. This has
been augmented a bit by using gpiochip_request_own_desc()
but this code really needs to be verified. If "native CS"
is actually an SoC GPIO, why is it even done this way?
Should this GPIO not just be defined in the device tree
like any other CS GPIO? I'm confused.
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Chris Boot <bootc@bootc.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190804003852.1312-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This converts the Freescale SPI master driver to use GPIO
descriptors for chip select handling.
The Freescale (fsl) driver has a lot of quirks to look up
"gpios" rather than "cs-gpios" from the device tree.
After the prior patch that will make gpiolib return the
GPIO descriptor for "gpios" in response to a request for
"cs-gpios", this code can be cut down quite a bit.
The driver has custom handling of chip select rather
than using the core (which may be possible but not
done in this patch) so it still needs to refer directly
to spi->cs_gpiod to set the chip select.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190804003539.985-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use the definition provided by include/asm/vmware.h.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Doug Covelli <dcovelli@vmware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-input@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: <pv-drivers@vmware.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190828080353.12658-5-thomas_os@shipmail.org
|
|
Use the definition provided by include/asm/vmware.h
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Doug Covelli <dcovelli@vmware.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: pv-drivers@vmware.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: VMware Graphics <linux-graphics-maintainer@vmware.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190828080353.12658-4-thomas_os@shipmail.org
|
|
The register number needs to be translated for chips with more than 8
ports. This patch fixes a bug causing all chips with more than 8 GPIO pins
to not work correctly.
Fixes: 0f25fda840a9 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The type of reg_direction needs to match the type of the regmap, which
is u8.
Fixes: 0f25fda840a9 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Cc: Cc: <stable@vger.kernel.org>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
The MT6358 is a regulator found on boards based on MediaTek MT8183 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1566531931-9772-8-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The parent image is read only up to the overlap point, the rest of
the buffer should be zeroed. This snuck in because as it turns out
the overlap test case has not been triggering this code path for
a while now.
Fixes: a9b67e69949d ("rbd: replace obj_req->tried_parent with obj_req->read_state")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
|
|
Currently big microservers have _XEON_D while small microservers have
_X, Make it uniformly: _D.
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_\(X\|XEON_D\)"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*ATOM.*\)_X/\1_D/g' \
-e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_XEON_D/\1_D/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190827195122.677152989@infradead.org
|
|
Currently big core clients with extra graphics on have:
- _G
- _GT3E
Make it uniformly: _G
for i in `git grep -l "\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*_GT3E"`
do
sed -i -e 's/\(\(INTEL_FAM6_\|VULNWL_INTEL\|INTEL_CPU_FAM6\).*\)_GT3E/\1_G/g' ${i}
done
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Link: https://lkml.kernel.org/r/20190827195122.622802314@infradead.org
|
