| Age | Commit message (Collapse) | Author |
|---|
|
We seem to have forgotten to check that iommu_fwspecs actually belong to
us before we go ahead and dereference their private data. Oops.
Fixes: 021bb8420d44 ("iommu/arm-smmu: Wire up generic configuration support")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
We now delay installing our per-bus iommu_ops until we know an SMMU has
successfully probed, as they don't serve much purpose beforehand, and
doing so also avoids fights between multiple IOMMU drivers in a single
kernel. However, the upshot of passing the return value of bus_set_iommu()
back from our probe function is that if there happens to be more than
one SMMUv3 device in a system, the second and subsequent probes will
wind up returning -EBUSY to the driver core and getting torn down again.
Avoid re-setting ops if ours are already installed, so that any genuine
failures stand out.
Fixes: 08d4ca2a672b ("iommu/arm-smmu: Support non-PCI devices with SMMUv3")
CC: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
CC: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The 32-bit ARM DMA configuration code predates the IOMMU core's default
domain functionality, and instead relies on allocating its own domains
and attaching any devices using the generic IOMMU binding to them.
Unfortunately, it does this relatively early on in the creation of the
device, before we've seen our add_device callback, which leads us to
attempt to operate on a half-configured master.
To avoid a crash, check for this situation on attach, but refuse to
play, as there's nothing we can do. This at least allows VFIO to keep
working for people who update their 32-bit DTs to the generic binding,
albeit with a few (innocuous) warnings from the DMA layer on boot.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Need to ensure that reg_output is not updated while setting multiple
bits. This makes the mutex locking behaviour for the set_multiple call
consistent with that of the set_value call.
Cc: stable@vger.kernel.org
Fixes: b4818afeacbd ("gpio: pca953x: Add set_multiple to allow multiple")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gpiod_set_array_value_complex does not clear the bits field.
Therefore when the drivers set_multiple funciton is called bits outside
the mask are undefined and can be either set or not. So bank_val needs
to be masked with bank_mask before or with the reg_val cache.
Cc: stable@vger.kernel.org
Fixes: b4818afeacbd ("gpio: pca953x: Add set_multiple to allow multiple")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Virtio 1.0 spec says VIRTIO_F_ANY_LAYOUT and VIRTIO_NET_F_GSO are
legacy-only feature bits. Do not negotiate them in virtio 1 mode. Note
this is a spec violation so we need to backport it to stable/downstream
kernels.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by class_find_device() in
hnae_get_handle() on errors and when later releasing the handle.
Fixes: 6fe6611ff275 ("net: add Hisilicon Network Subsystem...")
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Cc: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by bus_find_device() before
returning from emac_dev_open().
Note that phy_connect still takes a reference to the phy device.
Fixes: 5d69e0076a72 ("net: davinci_emac: switch to new mdio")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the references taken by of_get_child_by_name() and
bus_find_device() before returning from cpsw_phy_sel().
Note that holding a reference to the cpsw-phy-sel device does not
prevent the devres-managed private data from going away.
Fixes: 5892cd135e16 ("drivers: net: cpsw-phy-sel: Add new driver...")
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure to drop the reference taken by bus_find_device_by_name()
before returning from phy_connect() and phy_attach().
Note that both function still take a reference to the phy device
through phy_attach_direct().
Fixes: e13934563db0 ("[PATCH] PHY Layer fixup")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fix from Guenter Roeck:
"Fix resource leak on devm_kcalloc failure"
* tag 'hwmon-for-linus-v4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (core) fix resource leak on devm_kcalloc failure
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- modprobe-after-rmmod load failure bugfix for intel-ish, from Even Xu
- IRQ probing bugfix for intel-ish, from Srinivas Pandruvada
- attribute parsing fix in hid-sensor, from Ooi, Joyce
- other small misc fixes / quirky device additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: sensor: fix attributes in HID sensor interface
HID: intel-ish-hid: request_irq failure
HID: intel-ish-hid: Fix driver reinit failure
HID: intel-ish-hid: Move DMA disable code to new function
HID: intel-ish-hid: consolidate ish wake up operation
HID: usbhid: add ATEN CS962 to list of quirky devices
HID: intel-ish-hid: Fix !CONFIG_PM build warning
HID: sensor-hub: Fix packing of result buffer for feature report
|
|
On CZ/ST systems with AZ rather than ACP audio, we need to bail
early in hw_fini since there is nothing to do.
bug: https://bugs.freedesktop.org/show_bug.cgi?id=98276
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Valleyview appears to be limited to only scanning out from the first 512MiB
of the Global GTT. Lets presume that this behaviour was inherited from the
display block copied from g4x (not Ironlake) and all earlier generations
are similarly affected, though testing suggests different symptoms. For
simplicity, impose that these platforms must scanout from the mappable
region. (For extra simplicity, use HAS_GMCH_DISPLAY even though this
catches Cherryview which does not appear to be limited to the low
aperture for its scanout.)
v2: Use HAS_GMCH_DISPLAY() to more clearly convey my intent about
limiting this workaround to the old style of display engine.
v3: Update changelog to reflect testing by Ville Syrjälä
v4: Include the changes to the comments as well
Reported-by: Luis Botello <luis.botello.ortega@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98036
Fixes: 2efb813d5388 ("drm/i915: Fallback to using unmappable memory for scanout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.9-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20161107110128.28762-1-chris@chris-wilson.co.uk
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit 767a222e47cc13239d38018887f911fec06169ea)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When we split a large object up into chunks for GTT faulting (because we
can't fit the whole object into the aperture) we have to align our cuts
with the fence registers. Each partial VMA must cover a complete set of
tile rows or the offset into each partial VMA is not aligned with the
whole image. Currently we enforce a minimum size on each partial VMA,
but this minimum size itself was not aligned to the tile row causing
distortion.
Reported-by: Andreas Reis <andreas.reis@gmail.com>
Reported-by: Chris Clayton <chris2553@googlemail.com>
Reported-by: Norbert Preining <preining@logic.at>
Tested-by: Norbert Preining <preining@logic.at>
Tested-by: Chris Clayton <chris2553@googlemail.com>
Fixes: 03af84fe7f48 ("drm/i915: Choose partial chunksize based on tile row size")
Fixes: a61007a83a46 ("drm/i915: Fix partial GGTT faulting") # enabling patch
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98402
Testcase: igt/gem_mmap_gtt/medium-copy-odd
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <drm-intel-fixes@lists.freedesktop.org> # v4.9-rc1+
Link: http://patchwork.freedesktop.org/patch/msgid/20161107105443.27855-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 0ef723cbceb6dce8116e75d44c5b8679b2eba69a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
According to BSpec, cdclk for BDW has to be not less than 432 MHz with DP
audio enabled, port width x4, and link rate HBR2 (5.4 GHz). With cdclk less
than 432 MHz, enabling audio leads to pipe FIFO underruns and displays
cycling on/off.
Let's apply this work around to GEN9 platforms too, as it fixes the same
issue.
v2: Move drm_device to drm_i915_private conversion
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97907
Cc: stable@vger.kernel.org
Cc: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478117601-19122-1-git-send-email-dhinakaran.pandiyan@intel.com
(cherry picked from commit 9c7540241885838cfc7fa58c4a8bd75be0303ed1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
According to BSpec, cdclk for BDW has to be not less than 432 MHz with DP
audio enabled, port width x4, and link rate HBR2 (5.4 GHz). With cdclk less
than 432 MHz, enabling audio leads to pipe FIFO underruns and displays
cycling on/off.
From BSpec:
"Display» BDW-SKL» dpr» [Register] DP_TP_CTL [BDW+,EXCLUDE(CHV)]
Workaround : Do not use DisplayPort with CDCLK less than 432 MHz, audio
enabled, port width x4, and link rate HBR2 (5.4 GHz), or else there may
be audio corruption or screen corruption."
Since, some DP configurations (e.g., MST) use port width x4 and HBR2
link rate, let's increase the cdclk to >= 432 MHz to enable audio for those
cases.
v4: Changed commit message
v3: Combine BDW pixel rate adjustments into a function (Jani)
v2: Restrict fix to BDW
Retain the set cdclk across modesets (Ville)
Cc: stable@vger.kernel.org
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1478026080-2925-1-git-send-email-dhinakaran.pandiyan@intel.com
(cherry picked from commit b30ce9e0552aa017ac6f2243f3c2d8e36fe52e69)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
One of the CI machines began to run into issues with the hpd poller
suddenly waking up in the midst of the late suspend phase. It looks like
this is getting caused by the fact we now deinitialize power wells in
late suspend, which means that intel_hpd_poll_init() gets called in late
suspend causing polling to get re-enabled. So, when deinitializing power
wells on valleyview we now refrain from enabling polling in the midst of
suspend.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98040
Fixes: 19625e85c6ec ("drm/i915: Enable polling when we don't have hpd")
Signed-off-by: Lyude <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Cc: Petry Latvala <petri.latvala@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1477499769-1966-1-git-send-email-lyude@redhat.com
(cherry picked from commit b64b540931483cca3200d98756bed6ad0e01d75c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The VBT provides the platform a way to mix and match the DDI ports vs.
GMBUS pins. Currently we only trust the VBT for DDI E, which I suppose
has no standard GMBUS pin assignment. However, there are machines out
there that use a non-standard mapping for the other ports as well.
Let's start trusting the VBT on this one for all ports on DDI platforms.
I've structured the code such that other platforms could easily start
using this as well, by simply filling in the ddi_port_info. IIRC there
may be CHV system that might actually need this.
v2: Include a commit message, include a debug message during init
Cc: stable@vger.kernel.org
Cc: Maarten Maathuis <madman2003@gmail.com>
Tested-by: Maarten Maathuis <madman2003@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97877
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1476208368-5710-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
(cherry picked from commit e4ab73a13291fc844c9e24d5c347bd95818544d2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
If 'sun4i_layers_init()' returns an error, propagate it instead of
returning -EINVAL unconditionally.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
An interrupt may occur right after devm_request_irq() is called and
prior to the spinlock initialization, leading to a kernel oops,
as the interrupt handler uses the spinlock.
In order to prevent this problem, move the spinlock initialization
prior to requesting the interrupts.
Fixes: e4243f13d10e (mmc: mxs-mmc: add mmc host driver for i.MX23/28)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the eMMC 4.51 version of the spec, an EXT_CSD field called
GENERIC_CMD6_TIME[248] was added. This allows cards to specify the maximum
time it may need to move out from its busy state, when a CMD6 command has
been sent.
In cases when the card is compliant to versions < 4.51 of the eMMC spec,
obviously the core needs to use a fall-back value for this timeout, which
currently is set to 10 minutes. This value is completely in the wrong range
and importantly in some cases it causes a card initialization to take more
than 10 minute to complete.
Earlier this scenario was avoided as the mmc core used CMD13 to poll the
card, to find out when it stopped signaling busy. Commit 08573eaf1a70
("mmc: mmc: do not use CMD13 to get status after speed mode switch")
changed this behavior.
Instead of reverting that commit, which would cause other issues, let's
instead start by picking a simple solution for the problem, by using a
500ms default generic CMD6 timeout.
The reason for using exactly 500ms, comes from observations that shows it's
quite common for cards to specify 250ms. 500ms is two times that value so
likely it should be enough for most cards.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 08573eaf1a70 ("mmc: mmc: do not use CMD13 to get status after speed
mode switch")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Stephen Boyd <sboyd@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
|
|
mmc_test_check_result_async() requires that struct mmc_async_req is
contained within struct mmc_test_async_req. Fix the "Commands during
non-blocking write" tests so that is the case.
Fixes: 4bbb9aac9a9a ("mmc: mmc_test: Add tests for sending commands during transfer")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Restore enhanced strobe setting during runtime resume.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To prevent subsequent commands failing, ensure the cmd and data circuits
are reset after a tuning timeout.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the busy response case (i.e. !host->data), an unexpected data interrupt
would result in clearing the data command as though it had completed but
without informing the upper layers and thus resulting in a hang. Fix by
only clearing the data command for data interrupts that are expected.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
CMD line reset during an ongoing data transfer can cause the data transfer
to hang. Fix by delaying the reset until the data transfer is finished.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit cc7cc02bada8 ("PCI: Query platform firmware for device power
state") augmented struct pci_platform_pm_ops with a ->get_state hook and
implemented it for acpi_pci_platform_pm, the only pci_platform_pm_ops
existing till v4.7.
However v4.8 introduced another pci_platform_pm_ops for Intel Mobile
Internet Devices with commit 5823d0893ec2 ("x86/platform/intel-mid: Add
Power Management Unit driver"). It is missing the ->get_state hook,
which is fatal since pci_set_platform_pm() enforces its presence. Andy
Shevchenko reports that without the present commit, such a device
"crashes without even a character printed out on serial console and
reboots (since watchdog)".
Retrofit mid_pci_platform_pm with the missing callback to fix the
breakage.
Acked-and-tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fixes: cc7cc02bada8 ("PCI: Query platform firmware for device power state")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: http://lkml.kernel.org/r/7c1567d4c49303a4aada94ba16275cbf56b8976b.1477221514.git.lukas@wunner.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This basicly reverts commit e534f3e9 (staging:nvec: Introduce the use of
the managed version of kzalloc). Serio struct should never by managed
because it is refcounted. Doing so will lead to a double free oops on module
remove.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Fixes: e534f3e9429f ("staging:nvec: Introduce the use of the managed version of kzalloc")
Cc: stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 36b30d6138f4677514aca35ab76c20c1604baaad.
This is necessary to detect paz00 (ac100) touchpad properly as one
speaking ETPS/2 protocol. Without it X.org's synaptics driver doesn't
work as the touchpad is detected as an ImPS/2 mouse instead.
Commit ec6184b1c717b8768122e25fe6d312f609cc1bb4 changed the way
auto-detection is performed on ports marked as pass through and made the
issue apparent.
A pass through port is an additional PS/2 port used to connect a slave
device to a master device that is using PS/2 to communicate with the
host (so slave's PS/2 communication is tunneled over master's PS/2
link). "Synaptics PS/2 TouchPad Interfacing Guide" describes such a
setup (PS/2 PASS-THROUGH OPTION section).
Since paz00's embedded controller is not connected to a PS/2 port
itself, the PS/2 interface it exposes is not a pass-through one.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Acked-by: Marc Dietrich <marvin24@gmx.de>
Fixes: 36b30d6138f4 ("staging: nvec: ps2: change serio type to passthrough")
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This command was sent behind serio's back and the answer to it was
confusing atkbd probe function which lead to the elantech touchpad
getting detected as a keyboard.
To prevent this from happening just let every party do its part of the
job.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Acked-by: Marc Dietrich <marvin24@gmx.de>
Cc: stable <stable@vger.kernel.org> # 3.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to drop the device reference taken by of_find_device_by_node()
before returning from arche_platform_change_state().
Note that this code is expected to be removed, but let's fix up the leak
nonetheless.
Fixes: 886aba558b9e ("greybus: arche-platform: Export fn to allow...")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Vaibhav Hiremath <hvaibhav.linux@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
`ni_tio_clock_period_ps()` used to return the clock period in
picoseconds, and had a `BUG()` call for invalid cases. It was changed
to pass the clock period back via a pointer parameter and return an
error for the invalid cases. Unfortunately the code to handle
user-specified clock sources with user-specified clock period is still
returning the clock period the old way, which can lead to the caller not
getting the clock period, or seeing an unexpected error. Fix it by
passing the clock period via the pointer parameter and returning `0`.
Fixes: b42ca86ad605 ("staging: comedi: ni_tio: remove BUG() checks for ni_tio_get_clock_src()")
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: <stable@vger.kernel.org> # 4.7+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a pin depending on bit 6 in SCU90 is requested for GPIO, the export
will succeed but changes to the GPIO's value will not be accepted by the
hardware. This is because the pinmux driver has misconfigured the SCU by
writing 1 to the reserved bit.
The description of SCU90[6] from the datasheet is 'Reserved, must keep
at value ”0”'. The fix is to switch pinmux from the bit-flipping macro
to explicitly configuring the .enable and .disable values to zero.
The patch has been tested on an AST2500 EVB.
Fixes: 56e57cb6c07f (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Uma Yadlapati <yadlapat@us.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Early commit 30ca5cb63c56965 ("staging: sm750fb: change definition of
PANEL_PLANE_TL fields") and 27b047bbe1ee9c0 ("staging: sm750fb: change
definition of PANEL_PLANE_BR fields") modify the register bit fields
definitions. But the modifications are wrong, because the bit mask of
"bit field 10:0" is not 0xeff, but 0x7ff. The wrong definition bugs
makes display very strange.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for the TI CC3200 LaunchPad board, which uses a
custom USB vendor ID and product ID. Channel A is used for JTAG, and
channel B is used for a UART.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
variable struct usb_cdc_parsed_header h may be used
uninitialized in acm_probe.
In kernel 4.8.
/* handle quirks deadly to normal probing*/
if (quirks == NO_UNION_NORMAL)
...
goto skip_normal_probe;
}
we bypass call to
cdc_parse_cdc_header(&h, intf, buffer, buflen);
but later use h in
if (h.usb_cdc_country_functional_desc) { /* export the country data */
Signed-off-by: Oliver Neukum <oneukum@suse.com>
CC: stable@vger.kernel.org
Reported-by: Victor Sologoubov <victor0@rambler.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Never seen XHCI auto handoff working on TI and RENESAS cards.
Eventually, we force handoff. This code forces the handoff
unconditionally. It saves 5 seconds boot time for each card.
Signed-off-by: Babu Moger <babu.moger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Removing unnecessary duplicated actions that we've got while merging:
Commit 19915e623458 ("Merge 4.1-rc7 into usb-next")
[ b-liu@ti.com: added 'Commit' in the commit message ]
Signed-off-by: Kirill Esipov <yesipov@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This suppresses printing the error message "failed to get phy" in the
kernel log when the error is -EPROBE_DEFER. This prevents usless noise
in the kernel log.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 4.9 -rc
phy fixes:
*) Add a empty function for phy_reset when CONFIG_GENERIC_PHY is not set
*) change the phy lookup table for da8xx-usb to match it with the name
present in the board configuraion file (used for non-dt boot)
*) Fix incorrect programming sequence in w.r.t deassert of phy_rst
in phy-rockchip-pcie
*) Fix to avoid NULL pointer dereferencing error in sun4i phy
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Second set of IIO fixes for the 4.9 cycle.
Interestingly scale related fixes for accelerometers at both ends of
the range. Obviously more varied devices turning up than we've seen before!
* ad5933
- fix an uninitialized value in a return case that is winding up GCC.
* hid sensors
- missing pm function prevents hid rotations sensors from working on newer
ISH hubs (works by luck on older ones)
- increase of scale precision needed to fix a case where on a yoga 260
the reported scale is 0 (presumably a high precision but very low g sensor).
* st_sensors
- fix an issue seen with the hs3lis331dl where the range is much greater
than previous devices (100's of g) and hence the per bit scale is greater
than 1.
|
|
Add the "reset" as name of reset controller.
This is for preventing the wrong operation. Even if some SoC has reset
controller, doesn't define "resets" in device-tree.
Then it might be waiting for reset controller and it should be stuck.
Fixes: d6786fefe816 ("mmc: dw_mmc: add reset support to dwmmc host controller")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
into drm-fixes
Fixes for some msm issues
* 'msm-fixes-4.9' of git://people.freedesktop.org/~robclark/linux:
drm/msm: Fix error handling crashes seen when VRAM allocation fails
drm/msm/mdp5: 8x16 actually has 8 mixer stages
drm/msm/mdp5: no scaling support on RGBn pipes for 8x16
drm/msm/mdp5: handle non-fullscreen base plane case
drm/msm: Set CLK_IGNORE_UNUSED flag for PLL clocks
drm/msm/dsi: Queue HPD helper work in attach/detach callbacks
|
|
into drm-fixes
A few more fixes for 4.9.
* 'drm-fixes-4.9' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: add some error handling to amdgpu_init v2
drm/amd: fix scheduler fence teardown order v2
drm/amd/powerplay: don't succeed in getters if fan is missing
drm/amdgpu: make sure ddc_bus is valid in connector unregister
drm/radeon: Fix kernel panic on shutdown
drm/amdgpu: disable runtime pm in certain cases
drm/radeon: disable runtime pm in certain cases
drm/amdgpu: add support for new smc firmware on iceland
drm/amdgpu: add support for new smc firmware on tonga
|
|
'blk_mq_alloc_request()' returns an error pointer in case of error, not
NULL. So test it with IS_ERR.
Fixes: fd8383fd88a2 ("nbd: convert to blkmq")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"A bugfix for the I2C core fixing a (rare) race condition"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: fix NULL pointer dereference under race condition
|
|
Pull MD fixes from Shaohua Li:
"There are several bug fixes queued:
- fix raid5-cache recovery bugs
- fix discard IO error handling for raid1/10
- fix array sync writes bogus position to superblock
- fix IO error handling for raid array with external metadata"
* tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md: be careful not lot leak internal curr_resync value into metadata. -- (all)
raid1: handle read error also in readonly mode
raid5-cache: correct condition for empty metadata write
md: report 'write_pending' state when array in sync
md/raid5: write an empty meta-block when creating log super-block
md/raid5: initialize next_checkpoint field before use
RAID10: ignore discard error
RAID1: ignore discard error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two more important data integrity fixes related to RAID device drivers
which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
path and a memory leak in the scsi_debug driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - cleanup Focaltech code
Input: i8042 - add XMG C504 to keyboard reset table
|
