| Age | Commit message (Collapse) | Author |
|---|
|
Since we already have the useful atm_info() macro, use it instead of
raw atm_printk()
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201208093206.24780-2-info@metux.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If drivers work correctly, they should remain silent.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201208093206.24780-1-info@metux.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.11-rc1
- several refactoring patches of the core gpiolib code
- add support for NXP PCAL9554B/C to gpio-pca953x
- allow probing mockup devices from device tree
- refactoring and improvements to gpio-rcar
- improvements to locking in gpio-tegra
- code shrink in gpiolib devres
- get the irq offset from device tree in gpio-sifive
- major refactoring of gpio-exar
- convert gpio-mvebu pwm access to regmap
- create a new submenu for virtual GPIO drivers
- fix clang fall-through warnings treewide
- minor driver refactoring and tweaks sprinkled all over
|
|
The DDR Perf for i.MX8 is a system PMU whose AXI ID would different from
SoC to SoC. Need expose system PMU identifier for userspace which refer
to /sys/bus/event_source/devices/<PMU DEVICE>/identifier.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/20201130114202.26057-3-qiangqing.zhang@nxp.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Add an interface-number sanity check before testing the device flags to
avoid relying on undefined behaviour when left shifting in case a device
uses an interface number greater than or equal to BITS_PER_LONG (i.e. 64
or 32).
Reported-by: syzbot+8881b478dad0a7971f79@syzkaller.appspotmail.com
Fixes: c3a65808f04a ("USB: serial: option: reimplement interface masking")
Cc: stable@vger.kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Unmask EXTENDED_STATUS_MASK.vSafe0V, ALERT.Extended_Status
and set vbus_vsafe0v to enable VSAFE0V signalling.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change adds vbus_vsafe0v which when set, makes TCPM
query for VSAFE0V by assigning the tcpc.is_vbus_vsafe0v callback.
Also enables ALERT.ExtendedStatus which is triggered when
status of EXTENDED_STATUS.vSafe0V changes.
EXTENDED_STATUS.vSafe0V is set when vbus is at vSafe0V and
cleared otherwise.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TCPM at present lacks the notion of VSAFE0V. There
are three vbus threshold levels that are critical to track:
a. vSafe5V - VBUS “5 volts” as defined by the USB
PD specification.
b. vSinkDisconnect - Threshold used for transition from
Attached.SNK to Unattached.SNK.
c. vSafe0V - VBUS “0 volts” as defined by the USB
PD specification.
Tracking vSafe0V is crucial for entry into Try.SNK and
Attached.SRC and turning vbus back on by the source in
response to hard reset.
>From "4.5.2.2.8.2 Exiting from AttachWait.SRC State" section
in the Type-C spec:
"The port shall transition to Attached.SRC when VBUS is at
vSafe0V and the SRC.Rd state is detected on exactly one of
the CC1 or CC2 pins for at least tCCDebounce."
"A DRP that strongly prefers the Sink role may optionally
transition to Try.SNK instead of Attached.SRC when VBUS
is at vSafe0V and the SRC.Rd state is detected on exactly
one of the CC1 or CC2 pins for at least tCCDebounce."
>From "7.1.5 Response to Hard Resets" section in the PD spec:
"After establishing the vSafe0V voltage condition on VBUS,
the Source Shall wait tSrcRecover before re-applying VCONN
and restoring VBUS to vSafe5V."
vbus_present in the TCPM code tracks vSafe5V(vbus_present is true)
and vSinkDisconnect(vbus_present is false).
This change adds is_vbus_vsafe0v callback which when set makes
TCPM query for vSafe0V voltage level when needed.
Since not all TCPC controllers might have the capability
to report vSafe0V, TCPM assumes that vSafe0V is same as
vSinkDisconnect when is_vbus_vsafe0v callback is not set.
This allows TCPM to continue to support controllers which don't
have the support for reporting vSafe0V.
Introducing vSafe0V helps fix the failure reported at
"Step 15. CVS verifies PUT remains in AttachWait.SRC for 500ms"
of "TD 4.7.2 Try. SNK DRP Connect DRP Test" of
"Universal Serial Bus Type-C (USB Type-C) Functional Test
Specification Chapters 4 and 5". Here the compliance tester
intentionally maintains vbus at greater than vSafe0V and expects
the Product under test to stay in AttachWait.SRC till vbus drops
to vSafe0V.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202040840.663578-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
tcpm_check_send_discover does not clear the send_discover flag
when any of the following conditions are not met.
1. data_role is TYPEC_HOST
2. link is pd_capable
Discovery indentity would anyways not be attempted during
the current session anymore when the above conditions are not
met. Hence clear the send_discover flag here to prevent
tcpm_enable_frs_work from rescheduling indefinetly.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201203031908.1491542-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
nRetryCount was updated from 3 to 2 between PD2.0 and PD3.0 spec.
nRetryCount in "Table 6-34 Counter parameters" of the PD 2.0
spec is set to 3, whereas, nRetryCount in "Table 6-59 Counter
parameters" is set to 2.
Pass down negotiated rev in pd_transmit so that low level chip
drivers can update the retry count accordingly before attempting
packet transmission.
This helps in passing "TEST.PD.PORT.ALL.02" of the
"Power Delivery Merged" test suite which was initially failing
with "The UUT did not retransmit the message nReryCount times"
In fusb302 & tcpci drivers, by default the driver sets the retry
count to 3 (Default for PD 2.0). Update this to 2,
if the negotiated rev is PD 3.0.
In wcove, since the retry count is intentionally set to max, leaving
it as is.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20201202031733.647808-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When Intel PMC Mux agent driver receives the response message from PMC, it
checks for the same response bits for all the mux states.
Corrected it by checking correct response message bits, Bit 8 & 9 for the
SAFE Mode and Alternate Modes and Bit 16 & 17 for the Connect and
Disconnect Modes.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Utkarsh Patel <utkarsh.h.patel@intel.com>
Link: https://lore.kernel.org/r/20201203220813.16281-1-utkarsh.h.patel@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pm_runtime_enable will decrement the power disable depth. Imbalance
depth will resulted in enabling runtime PM of device fails later. Thus
a pairing decrement must be needed on the error handling path to keep it
balanced.
Fixes: 6c984b066d84b ("ARM: OMAP: USBHOST: Replace usbhs core driver APIs by Runtime pm APIs")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201123145719.1455849-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a USB2 device wakeup is not enabled/supported the link state may
still be in U0 in xhci_bus_suspend(), where it's then manually put
to suspended U3 state.
Just as with selective suspend the device needs time to enter U3
suspend before continuing with further suspend operations
(e.g. system suspend), otherwise we may enter system suspend with link
state in U0.
[commit message rewording -Mathias]
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Intel Maple Ridge is successor of Titan Ridge Thunderbolt controller. As
Titan Ridge this one also includes xHCI host controller. In order to
safe energy we should put it to low power state by default when idle.
For this reason allow host runtime PM for Maple Ridge.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-5-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xHCI controller on Alpine Ridge LP keeps the whole Thunderbolt
controller awake if the host controller is not allowed to sleep.
This is the case even if no USB devices are connected to the host.
Add the Intel Alpine Ridge LP product-id to the list of product-ids
for which we allow runtime PM by default.
Fixes: 2815ef7fe4d4 ("xhci-pci: allow host runtime PM as default for Intel Alpine and Titan Ridge")
Cc: <stable@vger.kernel.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Synopsys xHC has an internal TRB cache of size TRB_CACHE_SIZE for
each endpoint. The default value for TRB_CACHE_SIZE is 16 for SS and 8
for HS. The controller loads and updates the TRB cache from the transfer
ring in system memory whenever the driver issues a start transfer or
update transfer command.
For chained TRBs, the Synopsys xHC requires that the total amount of
bytes for all TRBs loaded in the TRB cache be greater than or equal to 1
MPS. Or the chain ends within the TRB cache (with a last TRB).
If this requirement is not met, the controller will not be able to send
or receive a packet and it will hang causing a driver timeout and error.
This can be a problem if a class driver queues SG requests with many
small-buffer entries. The XHCI driver will create a chained TRB for each
entry which may trigger this issue.
This patch adds logic to the XHCI driver to detect and prevent this from
happening.
For every (TRB_CACHE_SIZE - 2), we check the total buffer size of
the SG list and if the last window of (TRB_CACHE_SIZE - 2) SG list length
and we don't make up at least 1 MPS, we create a temporary buffer to
consolidate full SG list into the buffer.
We check at (TRB_CACHE_SIZE - 2) window because it is possible that there
would be a link and/or event data TRB that take up to 2 of the cache
entries.
We discovered this issue with devices on other platforms but have not
yet come across any device that triggers this on Linux. But it could be
a real problem now or in the future. All it takes is N number of small
chained TRBs. And other instances of the Synopsys IP may have smaller
values for the TRB_CACHE_SIZE which would exacerbate the problem.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit uses the private data passed by parent device
to set the quirk for Synopsys xHC. This patch fixes the
SNPS xHC hang issue when the data is scattered across
small buffers which does not make atleast MPS size for
given TRB cache size of SNPS xHC.
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201208092912.1773650-2-mathias.nyman@linux.intel.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy into char-misc-next
Vinod writes:
phy-for-5.11
- New phy drivers:
- Mediatek MT7621 PCIe PHY (promoted from staging)
- Ingenic USB phy driver supporting JZ4775 and X2000
- Intel Keem Bay USB PHY driver
- Marvell USB HSIC PHY driver supporting MMP3 SoC
- AXG MIPI D-PHY driver
- Updates:
- Conversion to YAML binding for:
- Broadcom SATA PHY
- Cadence Sierra PHY bindings
- STM32 USBC Phy
- Support for Exynos5433 PCIe PHY
- Support for Qualcomm SM8250 PCIe QMP PHY
- Support for Exynos5420 USB2 phy
- devm_platform_ioremap_resource conversion for bunch of drivers
* tag 'phy-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
drm/mediatek: avoid dereferencing a null hdmi_phy on an error message
phy: ingenic: depend on HAS_IOMEM
phy: mediatek: statify mtk_hdmi_phy_driver
dt-bindings: phy: Convert Broadcom SATA PHY to YAML
devicetree: phy: rockchip-emmc add output-tapdelay-select
phy: rockchip-emmc: output tap delay dt property
PHY: Ingenic: Add USB PHY driver using generic PHY framework.
dt-bindings: USB: Add bindings for Ingenic JZ4775 and X2000.
USB: PHY: JZ4770: Remove unnecessary function calls.
devicetree: phy: rockchip-emmc: pulldown property
phy: rockchip: set pulldown for strobe line in dts
phy: renesas: rcar-gen3-usb2: disable runtime pm in case of failure
phy: mediatek: allow compile-testing the hdmi phy
phy/rockchip: Make PHY_ROCKCHIP_INNO_HDMI depend on HAS_IOMEM to fix build error
phy: samsung: Merge Kconfig for Exynos5420 and Exynos5250
phy: ralink: phy-mt7621-pci: set correct name in MODULE_DEVICE_TABLE macro
phy: ralink: phy-mt7621-pci: drop 'COMPILE_TEST' from Kconfig
phy: mediatek: Make PHY_MTK_{XSPHY, TPHY} depend on HAS_IOMEM and OF_ADDRESS to fix build errors
phy: tegra: xusb: Fix usb_phy device driver field
phy: amlogic: replace devm_reset_control_array_get()
...
|
|
The Canaan Kendryte K210 RISC-V SoC includes a DW apb_ssi v4 controller
which is documented to have a 32 words deep TX and RX FIFO. The FIFO
length detection in spi_hw_init() correctly detects this value.
However, when the controller RX FIFO is filled up to 32 entries
(RXFLR = 32), an RX FIFO overrun error occurs. This likely due to a
hardware bug which can be avoided by force setting the fifo_len field of
struct dw_spi to 31.
Define the dw_spi_canaan_k210_init() function to force set fifo_len to
31 when the device node compatible string is "canaan,k210-spi".
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-4-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The Synopsis DesignWare DW_apb_ssi specifications version 3.23 onward
define a 32-bits maximum transfer size synthesis parameter
(SSI_MAX_XFER_SIZE=32) in addition to the legacy 16-bits configuration
(SSI_MAX_XFER_SIZE=16) for SPI controllers. When SSI_MAX_XFER_SIZE=32,
the layout of the ctrlr0 register changes, moving the data frame format
field from bits [3..0] to bits [16..20], and the RX/TX FIFO word size
can be up to 32-bits.
To support this new format, introduce the DW SPI capability flag
DW_SPI_CAP_DFS32 to indicate that a controller is configured with
SSI_MAX_XFER_SIZE=32. Since SSI_MAX_XFER_SIZE is a controller synthesis
parameter not accessible through a register, the detection of this
parameter value is done in spi_hw_init() by writing and reading the
ctrlr0 register and testing the value of bits [3..0]. These bits are
ignored (unchanged) for SSI_MAX_XFER_SIZE=16, allowing the detection.
If a DFS32 capable SPI controller is detected, the new field dfs_offset
in struct dw_spi is set to SPI_DFS32_OFFSET (16).
dw_spi_update_config() is modified to set the data frame size field at
the correct position is the CTRLR0 register, as indicated by the
dfs_offset field of the dw_spi structure.
The DW_SPI_CAP_DFS32 flag is also unconditionally set for SPI slave
controllers, e.g. controllers that have the DW_SPI_CAP_DWC_SSI
capability flag set. However, for these ssi controllers, the dfs_offset
field is set to 0 as before (as per specifications).
Finally, for any controller with the DW_SPI_CAP_DFS32 capability flag
set, dw_spi_add_host() extends the value of bits_per_word_mask from
16-bits to 32-bits. dw_reader() and dw_writer() are also modified to
handle 32-bits iTX/RX FIFO words.
Suggested-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20201206011817.11700-3-damien.lemoal@wdc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The function has a single caller, so open code it there and take
advantage of the precalculated page count variable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20201209112019.2625029-1-hch@lst.de
Signed-off-by: Will Deacon <will@kernel.org>
|
|
kvmarm-master/next
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
Commit 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated
memory") introduced usage of ZONE_DEVICE memory for foreign memory
mappings.
Unfortunately this collides with using page->lru for Xen backend
private page caches.
Fix that by using page->zone_device_data instead.
Cc: <stable@vger.kernel.org> # 5.9
Fixes: 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated memory")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovksy@oracle.com>
Reviewed-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
Instead of having similar helpers in multiple backend drivers use
common helpers for caching pages allocated via gnttab_alloc_pages().
Make use of those helpers in blkback and scsiback.
Cc: <stable@vger.kernel.org> # 5.9
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovksy@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
When reporting the state of a GPIO to userspace, we never check
for the actual validity of the line, meaning we report invalid
lines as being usable. A subsequent request will fail though,
which is an inconsistent behaviour from a userspace perspective.
Instead, let's check for the validity of the line and report it
as used if it is invalid. This allows a tool such as gpioinfo
to report something sensible:
gpiochip3 - 4 lines:
line 0: unnamed unused input active-high
line 1: unnamed kernel input active-high [used]
line 2: unnamed kernel input active-high [used]
line 3: unnamed unused input active-high
In this example, lines 1 and 2 are invalid, and cannot be used by
userspace.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201204164739.781812-2-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
EIC controller have unfixed numbers of banks on different Spreadtrum SoCs,
and each bank has its own base address, the loop of getting there base
address in driver should break if the resource gotten via
platform_get_resource() is NULL already. The later ones would be all NULL
even if the loop continues.
Fixes: 25518e024e3a ("gpio: Add Spreadtrum EIC driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201209055106.840100-1-zhang.lyra@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Mistakenly the buffers (input and output) become enabled together for a short
period of time during GPIO request. This is problematic, because instead of
initial motive to disable them in the commit af7e3eeb84e2
("pinctrl: intel: Disable input and output buffer when switching to GPIO"),
the driven value on the pin, which might be used as an IRQ line, brings
firmwares of some touch pads to an awkward state that needs a full power off
to recover. Fix this, as stated in the culprit commit, by disabling the buffers.
Fixes: af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210497
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201208182403.40435-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Now that ARM started following the example of arm64 and RISC-V, and
no longer imposes any restrictions on the placement of the FDT in
memory at boot, we no longer need per-arch implementations of
efi_get_max_fdt_addr() to factor out the differences. So get rid of
it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Link: https://lore.kernel.org/r/20201029134901.9773-1-ardb@kernel.org
|
|
Since the UEFI 2.8A specification the UEFI enabled firmware provides a
configuration table EFI_RT_PROPERTIES_TABLE which indicates which runtime
services are enabled. The EFI stub reads this table and saves the value of
the field RuntimeServicesSupported internally.
The Firmware Test Suite requires the value to determine if UEFI runtime
services are correctly implemented.
With this patch an IOCTL call is provided to read the value of the field
RuntimeServicesSupported, e.g.
#define EFI_RUNTIME_GET_SUPPORTED_MASK \
_IOR('p', 0x0C, unsigned int)
unsigned int mask;
fd = open("/dev/efi_test", O_RDWR);
ret = ioctl(fd, EFI_RUNTIME_GET_SUPPORTED_MASK, &mask);
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Link: https://lore.kernel.org/r/20201127192051.1430-1-xypron.glpk@gmx.de
Acked-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Ivan Hu <ivan.hu@canonical.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Scatter-gather lists passed to UpdateCapsule() should be cleaned
from the D-cache to ensure that they are visible to the CPU after a
warm reboot before the MMU is enabled. On ARM and arm64 systems, this
implies a D-cache clean by virtual address to the point of coherency.
However, due to the fact that the firmware itself is not able to map
physical addresses back to virtual addresses when running under the OS,
this must be done by the caller.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
ofdm_index[] is used to indicate how many power compensation is needed to
current thermal value. For internal PA module or 2.4G band, the min_index
is different from other cases.
This issue originally is reported by Dan. He found the size of ofdm_index[]
is 2, but access index 'i' may be equal to 2 if 'rf' is 2 in case of
'is2t'.
In fact, the chunk of code is added to wrong place, so move it back to
proper place, and then power compensation and buffer overflow are fixed.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201207031903.7599-1-pkshih@realtek.com
|
|
Assure that frames with the fixed order flag are not reordered
relative to each other. This is accomplished by transmitting them
using a fixed priority independent of their QoS field.
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201104061823.197407-6-Mathy.Vanhoef@kuleuven.be
|
|
Currently 256 bitmap in blockack frames is being set only for AP mode.
Fix this to set whenever beacon has changed and has HE capability, there
by supporting mesh as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-5-pradeepc@codeaurora.org
|
|
HE operation IE in beacons is constructed based on userspace params,
which firmware might not be aware of. This causes firmware not to
configure TXOP duration based RTS threshold which could cause mismatch
in behaviour with respect to what is being advertised in beacons. This
patch sends HE operation IE fetched from beacon to firmware using
WMI interface for configuration.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-4-pradeepc@codeaurora.org
|
|
WMI_VDEV_PARAM_TX_OFDMA_CPLEN has been added with incorrect enum
value. Fix the enum to represent WMI param for configuring HE
operation field.
This is applicable to firmwares under
https://github.com/kvalo/ath11k-firmware/tree/master/IPQ8074/hw2.0
https://github.com/kvalo/ath11k-firmware/tree/master/IPQ6018/hw1.0
https://github.com/kvalo/ath11k-firmware/tree/master/QCN9074/hw1.0
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201020183111.25458-3-pradeepc@codeaurora.org
|
|
These error paths need to drop the &ar->conf_mutex before returning.
Fixes: 690ace20ff79 ("ath11k: peer delete synchronization with firmware")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/X85sVGVP/0XvlrEJ@mwanda
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* fall through */ comment with the new
pseudo-keyword macro fallthrough; instead of letting the code fall
through to the next case.
Notice that Clang doesn't recognize /* fall through */ comments as
implicit fall-through markings.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/f932c887e013767cbdabfdddd671086e8ae63193.1605896060.git.gustavoars@kernel.org
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/04257418814755f081fa0ac14a61b01328cdc4ed.1605896059.git.gustavoars@kernel.org
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/e127232621c4de340509047a11d98093958303c5.1605896059.git.gustavoars@kernel.org
|
|
QMI sequence fails if caldata file is not available.
It is observed that 'rmmod ath11k' fails if qmi message fails.
With this patch rmmod/insmod is working.
Logs:
Direct firmware load for IPQ8074/caldata.bin failed with error -2
Falling back to user helper
qmi failed to load CAL: IPQ8074/caldata.bin
qmi failed to load board data file:-11
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01699-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606916215-24643-1-git-send-email-akolli@codeaurora.org
|
|
|
|
The opp binding now allows to have an empty opp table and shared-opp to
still describe that devices share v/f lines.
When initialising an empty opp table, allow such case by:
- treating such conditions with warnings in place of errors
- don't fail on empty table
Signed-off-by: Nicola Mazzucato <nicola.mazzucato@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra check. Drop them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra check. Drop them.
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra check. Drop them.
Reviewed-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra check. Drop them.
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra checks. Drop them.
Reviewed-by: Ilia Lin <ilia.lin@kernel.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra checks. Drop them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
This allows the callers to drop the unnecessary checks.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
It has been found that some users (like cpufreq-dt and others on LKML)
have abused the helper dev_pm_opp_get_opp_table() to create the OPP
table instead of just finding it, which is the wrong thing to do. This
routine was meant for OPP core's internal working and exposed the whole
functionality by mistake.
Change the scope of dev_pm_opp_get_opp_table() to only finding the
table. The internal helpers _opp_get_opp_table*() are thus renamed to
_add_opp_table*(), dev_pm_opp_get_opp_table_indexed() is removed (as we
don't need the index field for finding the OPP table) and so the only
user, genpd, is updated.
Note that the prototype of _add_opp_table() was already left in opp.h by
mistake when it was removed earlier and so we weren't required to add it
now.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
