| Age | Commit message (Collapse) | Author |
|---|
|
We should unreference a gem object instead of an amdgpu bo here.
Fixes: fd9a9f8801de ("drm/amdgpu: Use GEM obj reference for KFD BOs")
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Per PCIe r5.0, sec 7.5.3.16, Downstream Ports must disable LTR if the link
goes down (the Port goes DL_Down status). This is a problem because the
Downstream Port's dev->ltr_path is still set, so we think LTR is still
enabled, and we enable LTR in the Endpoint. When it sends LTR messages,
they cause Unsupported Request errors at the Downstream Port.
This happens in the reset path, where we may enable LTR in
pci_restore_pcie_state() even though the Downstream Port disabled LTR
because the reset caused a link down event.
It also happens in the hot-remove and hot-add path, where we may enable LTR
in pci_configure_ltr() even though the Downstream Port disabled LTR when
the hot-remove took the link down.
In these two scenarios, check the upstream bridge and restore its LTR
enable if appropriate.
The Unsupported Request may be logged by AER as follows:
pcieport 0000:00:1d.0: AER: Uncorrected (Non-Fatal) error received: id=00e8
pcieport 0000:00:1d.0: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, id=00e8(Requester ID)
pcieport 0000:00:1d.0: device [8086:9d18] error status/mask=00100000/00010000
pcieport 0000:00:1d.0: [20] Unsupported Request (First)
In addition, if LTR is not configured correctly, the link cannot enter the
L1.2 state, which prevents some machines from entering the S0ix low power
state.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20211012075614.54576-1-mingchuang.qiao@mediatek.com
Reported-by: Utkarsh H Patel <utkarsh.h.patel@intel.com>
Signed-off-by: Mingchuang Qiao <mingchuang.qiao@mediatek.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
Biggest change is, that we have now support for a reset controller inside the
mmsys. This goes inhand with changes to the driver, that you will find in the
soc pull request.
Mediatek PCI device tree binding described the root port in a wrong. The IP
actaully implements several root complex with everyone having a single root port.
We need to fix the DT in an incompatible way to describe the HW as it is. This
also fixes a problem that no IRQ bigger then 32 could be handled.
The only public available HW that is affected by this is the BananaPi R64. I'm
not aware that there is a big user base using the upstream kernel. In this
boards PCI is only used for extension cards, so I don't expect any boot problems.
- mt8173: add reset for dsi0 to mmsys
- move dt-bindings reset controller includes to correct folder
- split PCIe node to use new format for mt2712 and mt7622
- mt8183: add audio node to chromebook devices
- mt8192: add clock controller node
* tag 'v5.15-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8183: Add the mmsys reset bit to reset the dsi0
arm64: dts: mt8173: Add the mmsys reset bit to reset the dsi0
dt-bindings: display: mediatek: add dsi reset optional property
dt-bindings: mediatek: Add #reset-cells to mmsys system controller
arm64: dts: mediatek: Move reset controller constants into common location
arm64: dts: mediatek: Split PCIe node for MT2712 and MT7622
arm64: dts: mt8183: add kukui platform audio node
arm64: dts: mt8183: add audio node
arm64: dts: mediatek: Add mt8192 clock controllers
Link: https://lore.kernel.org/r/1a3d63a3-c020-3319-26f6-a2ec338cc42e@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This memset in the fast path costs a lot of cycles on my setup. Here's a
top-of-profile of doing ~6.7M IOPS:
+ 5.90% io_uring [nvme] [k] nvme_queue_rq
+ 5.32% io_uring [nvme_core] [k] nvme_setup_cmd
+ 5.17% io_uring [kernel.vmlinux] [k] io_submit_sqes
+ 4.97% io_uring [kernel.vmlinux] [k] blkdev_direct_IO
and a perf diff with this patch:
0.92% +4.40% [nvme_core] [k] nvme_setup_cmd
reducing it from 5.3% to only 0.9%. This takes it from the 2nd most
cycle consumer to something that's mostly irrelevant.
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We don't have to worry about doing extra memsets by moving it outside
the protection of RQF_DONTPREP, as nvme doesn't do partial completions.
This is in preparation for making the read/write fast path not do a full
memset of the command.
Reviewed-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add 22.5 Gbps link rate definitions.
Link: https://lore.kernel.org/r/20211018070611.26428-1-sreekanth.reddy@broadcom.com
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Just use the %pg format specifier instead.
Link: https://lore.kernel.org/r/20211018065052.1822500-1-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use the memcpy_{from,to}_bvec() helpers instead of open coding them.
Link: https://lore.kernel.org/r/20211018060802.1815982-1-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Return the error code if ice_eswitch_configure() fails. Don't return
success.
Fixes: 1c54c839935b ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use 2-factor multiplication argument form devm_kcalloc() instead
of devm_kzalloc().
Link: https://github.com/KSPP/linux/issues/162
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This patch improves a few things:
- it fixes issue where ethtool -i reports that PR supports
priv-flags and tests when in fact it does not support them
- instead of using the same functions for both PF and PR ethtool ops,
this patch introduces separate ops for both cases and internal
functions with core logic.
- prevent accessing VF VSI while VF is not ready by calling
ice_check_vf_ready_for_cfg
- all PR specific functions in ethtool.c were moved to one place in
file
- instead overwriting n_priv_flags in ice_repr_get_drvinfo,
priv-flags code was moved from __ice_get_drvinfo to ice_get_drvinfo
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently it is not possible to set/unset lb_en and lan_en flags
for advanced rules during their creation. Both flags are enabled
by default. In case of switchdev offloads for egress traffic we
need lb_en to be disabled. Because of that, we work around it by
updating the rule immediately after its creation.
This change allows us to set/unset those flags right away and it
gets rid of old workaround as well. Using ice_adv_rule_flags_info
structure we can pass info about flags we want to be set for
a given advanced rule. Flags are stored in flags_info.act.
Values from act would be used only if act_valid was set to true,
otherwise default values would be used.
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Merge issues caused the check for switchdev mode has been inserted
in wrong place. It should be in ice_set_vf_trust not in ice_set_vf_mac.
Trusted VFs are forbidden in switchdev mode because they should
be configured only from the host side.
Fixes: 1c54c839935b ("ice: enable/disable switchdev when managing VFs")
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver tried to work around missing completion events that occurred
while interrupts are disabled, by triggering a software interrupt
whenever we exit polling (but we had to have polled at least once).
This was causing a *lot* of extra interrupts for some workloads like
NVMe over TCP, which resulted in regressions in performance. It was also
visible when polling didn't prevent interrupts when busy_poll was
enabled.
Fix the extra interrupts by utilizing our previously unused 3rd ITR
(interrupt throttle) index and set it to 20K interrupts per second, and
then trigger a software interrupt within that rate limit.
While here, slightly refactor the code to avoid an overwrite of a local
variable in the case of wb_en = true.
Fixes: b7306b42beaf ("ice: manage interrupts during poll exit")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If the adaptive settings are changed with
ethtool -C ethx adaptive-rx off adaptive-tx off
then the interrupt rate limit should be maintained as a user set value,
but only if BOTH adaptive settings are off. Fix a bug where the rate
limit that was being used in adaptive mode was staying set in the
register but was not reported correctly by ethtool -c ethx. Due to long
lines include a small refactor of q_vector variable.
Fixes: b8b4772377dd ("ice: refactor interrupt moderation writes")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver was having trouble with unreliable latency when doing single
threaded ping-pong tests. This was root caused to the DIM algorithm
landing on a too slow interrupt value, which caused high latency, and it
was especially present when queues were being switched frequently by the
scheduler as happens on default setups today.
In attempting to improve this, we allow the upper rate limit for
interrupts to move to rate limit of 4 microseconds as a max, which means
that no vector can generate more than 250,000 interrupts per second. The
old config was up to 100,000. The driver previously tried to program the
rate limit too frequently and if the receive and transmit side were both
active on the same vector, the INTRL would be set incorrectly, and this
change fixes that issue as a side effect of the redesign.
This driver will operate from now on with a slightly changed DIM table
with more emphasis towards latency sensitivity by having more table
entries with lower latency than with high latency (high being >= 64
microseconds).
The driver also resets the DIM algorithm state with a new stats set when
there is no work done and the data becomes stale (older than 1 second),
for the respective receive or transmit portion of the interrupt.
Add a new helper for setting rate limit, which will be used more
in a followup patch.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
If acpi_device_sleep_wake() called by acpi_enable_wakeup_device_power()
returns an error which means that the evaluation of either _DWS or
_PSW has failed, turn off all of the device's wakeup power resources
to be consistent with the clearing of dev->wakeup.prepare_count.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If an ACPI wakeup power resource is shared between multiple devices,
it may not be managed correctly.
Suppose, for example, that two devices, A and B, share a wakeup power
resource P whose wakeup_enabled flag is 0 initially. Next, suppose
that wakeup power is enabled for A and B, in this order, and disabled
for B. When wakeup power is enabled for A, P will be turned on and
its wakeup_enabled flag will be set. Next, when wakeup power is
enabled for B, P will not be touched, because its wakeup_enabled flag
is set. Now, when wakeup power is disabled for B, P will be turned
off which is incorrect, because A will still need P in order to signal
wakeup.
Moreover, if wakeup power is enabled for A and then disabled for B,
the latter will cause P to be turned off incorrectly (it will be still
needed by A), because acpi_disable_wakeup_device_power() is allowed
to manipulate power resources when the wakeup.prepare_count counter
of the given device is 0.
While the first issue could be addressed by changing the
wakeup_enabled power resource flag into a counter, addressing the
second one requires modifying acpi_disable_wakeup_device_power() to
do nothing when the target device's wakeup.prepare_count reference
counter is zero and that would cause the new counter to be redundant.
Namely, if acpi_disable_wakeup_device_power() is modified as per the
above, every change of the new counter following a wakeup.prepare_count
change would be reflected by the analogous change of the main reference
counter of the given power resource.
Accordingly, modify acpi_disable_wakeup_device_power() to do nothing
when the target device's wakeup.prepare_count reference counter is
zero and drop the power resource wakeup_enabled flag altogether.
While at it, ensure that all of the power resources that can be
turned off will be turned off when disabling device wakeup due to
a power resource manipulation error, to prevent energy from being
wasted.
Fixes: b5d667eb392e ("ACPI / PM: Take unusual configurations of power resources into account")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If an ACPI power resource is found to be "on" during the
initialization of the list of wakeup power resources of a device,
it is reference counted and its wakeup_enabled flag is set, which is
problematic if the deivce in question is the only user of the given
power resource, it is never runtime-suspended and it is not allowed
to wake up the system from sleep, because in that case the given
power resource will stay "on" until the system reboots and energy
will be wasted.
It is better to simply turn off wakeup power resources that are "on"
during the initialization unless their reference counters are not
zero, because that may be the only opportunity to prevent them from
staying in the "on" state all the time.
Fixes: b5d667eb392e ("ACPI / PM: Take unusual configurations of power resources into account")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To avoid situations in which the actual states of certain ACPI power
resources are not known just because they have never been referenced
by any device configuration objects, check the initial states of all
power resources as soon as they are found in the ACPI namespace (and
fall back to turning them on if the state check fails).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Andreas K. Huettel <andreas.huettel@ur.de>
|
|
Commit 6381195ad7d0 ("ACPI: power: Rework turning off unused power
resources") caused power resources in unknown state with reference
counters equal to zero to be turned off too, but that caused issues
to appear in the field, so modify the code to only turn off power
resources that are known to be "on".
Link: https://lore.kernel.org/linux-acpi/6faf4b92-78d5-47a4-63df-cc2bab7769d0@molgen.mpg.de/
Fixes: 6381195ad7d0 ("ACPI: power: Rework turning off unused power resources")
Reported-by: Andreas K. Huettel <andreas.huettel@ur.de>
Tested-by: Andreas K. Huettel <andreas.huettel@ur.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: 5.14+ <stable@vger.kernel.org> # 5.14+
|
|
In the probe function, the clock IDs were pointed to local variables
which should only be used in the same code block, and any access to them
after the probing stage becomes an use-after-free case.
Since there are only limited variants of the gce clock names so far, we
can just declare them as static constants to fix the issue.
Fixes: 85dfdbfc13ea ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
of_alias_get_id() may return -ENODEV which leads to illegal access to
the cmdq->clocks array.
Adding a check over alias_id to prevent the unexpected behavior.
Fixes: 85dfdbfc13ea ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
A small series to clean up the mlx5 mkey code across the mlx5_core and
InfiniBand.
* branch 'mlx5_mkey':
RDMA/mlx5: Attach ndescs to mlx5_ib_mkey
RDMA/mlx5: Move struct mlx5_core_mkey to mlx5_ib
RDMA/mlx5: Replace struct mlx5_core_mkey by u32 key
RDMA/mlx5: Remove pd from struct mlx5_core_mkey
RDMA/mlx5: Remove size from struct mlx5_core_mkey
RDMA/mlx5: Remove iova from struct mlx5_core_mkey
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Implement ndo_set_vf_rate to support setting of min_tx_rate and
max_tx_rate; set the appropriate bandwidth in the scheduler for the
node representing the specified VF VSI.
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use the new soc_intel_is_cht() helper to find out if we are running
on a CHT device rather then checking the ACPI _HRV field.
This is more reliable (some CHT devices have been found where the _HRV
for the PMIC is 2 rather then 3) and leads to a nice cleanup.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211018143324.296961-4-hdegoede@redhat.com
|
|
Use the new soc_intel_is_byt()/_cht() helpers to clean things up a bit.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211018143324.296961-3-hdegoede@redhat.com
|
|
A new warning in clang points out a use of bitwise OR with boolean
expressions in this driver:
drivers/platform/x86/thinkpad_acpi.c:9061:11: error: use of bitwise '|' with boolean operands [-Werror,-Wbitwise-instead-of-logical]
else if ((strlencmp(cmd, "level disengaged") == 0) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/platform/x86/thinkpad_acpi.c:9061:11: note: cast one or both operands to int to silence this warning
1 error generated.
This should clearly be a logical OR so change it to fix the warning.
Fixes: fe98a52ce754 ("ACPI: thinkpad-acpi: add sysfs support to fan subdriver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1476
Reported-by: Tor Vic <torvic9@mailbox.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20211018182537.2316800-1-nathan@kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
coccicheck complains about the use of snprintf() in sysfs show
functions:
WARNING use scnprintf or sprintf
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Ye Guojin <ye.guojin@zte.com.cn>
Link: https://lore.kernel.org/r/20211018091750.858826-1-ye.guojin@zte.com.cn
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
sysfs_emit
show() must not use snprintf() when formatting the value to be
returned to user space.
Fix the coccicheck warnings:
WARNING: use scnprintf or sprintf.
Use sysfs_emit instead of scnprintf or sprintf makes more sense.
Signed-off-by: Qing Wang <wangqing@vivo.com>
Link: https://lore.kernel.org/r/1634280641-4862-1-git-send-email-wangqing@vivo.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The ACPI_HANDLE() macro is a wrapper arond the ACPI_COMPANION()
macro and the ACPI handle produced by the former comes from the
ACPI device object produced by the latter, so it is way more
straightforward to evaluate the latter directly instead of passing
the handle produced by the former to acpi_bus_get_device().
Modify ideapad_acpi_add() accordingly (no intentional functional
impact).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/8000884.T7Z3S40VBb@kreacher
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
If the ACPI companion of a given device is not present, the result
of the ACPI_HANDLE() evaluation for it will be NULL, so calling
acpi_bus_get_device() on ACPI_HANDLE() result in order to validate
it is redundant.
Drop the redundant acpi_bus_get_device() call from mshw0011_notify()
along with a local variable related to it.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/3160001.aeNJFYEL58@kreacher
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
The ACPI_HANDLE() macro is a wrapper arond the ACPI_COMPANION()
macro and the ACPI handle produced by the former comes from the
ACPI device object produced by the latter, so it is way more
straightforward to evaluate the latter directly instead of passing
the handle produced by the former to acpi_bus_get_device().
Modify s3_wmi_check_platform_device() accordingly (no intentional
functional impact).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com>
Link: https://lore.kernel.org/r/12896717.uLZWGnKmhe@kreacher
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Create the attribute groups for kb_led_color and set the `groups` field
in kb_led. While touching it, also change its show method to use
sysfs_emit() instead of sprintf().
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-5-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
System76 laptops running open source EC firmware support configuring
charging thresholds through ACPI methods. Expose this functionality
through the standard sysfs entries charge_control_{start,end}_threshold.
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-4-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
System76 laptops models with OLED displays do not support the default
Fn+F2 behavior of turning the embedded display on and off. Some models
instead introduce a new notify event that is used to lock the screen so
the OS will put the display in a low power state.
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-3-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
Add a hwmon interface to report CPU/GPU temperature and fan speed.
sensors now reports an ACPI interface with the entries:
system76_acpi-acpi-0
Adapter: ACPI interface
CPU fan: 0 RPM
GPU fan: 0 RPM
CPU temp: +47.0°C
GPU temp: +0.0°C
Signed-off-by: Jeremy Soller <jeremy@system76.com>
Signed-off-by: Tim Crawford <tcrawford@system76.com>
Link: https://lore.kernel.org/r/20211006202202.7479-2-tcrawford@system76.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
dma_pool_alloc/memset()
Replacing dma_pool_alloc/memset() with dma_pool_zalloc()
to simplify the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'destroy_workqueue()' already drains the queue before destroying it, so
there is no need to flush it explicitly.
Remove the redundant 'flush_workqueue()' calls.
This was generated with coccinelle:
@@
expression E;
@@
- flush_workqueue(E);
destroy_workqueue(E);
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactoring of the Atari floppy driver when converting to blk-mq
has broken the state machine in not-so-subtle ways:
finish_fdc() must be called when operations on the floppy device
have completed. This is crucial in order to relase the ST-DMA
lock, which protects against concurrent access to the ST-DMA
controller by other drivers (some DMA related, most just related
to device register access - broken beyond compare, I know).
When rewriting the driver's old do_request() function, the fact
that finish_fdc() was called only when all queued requests had
completed appears to have been overlooked. Instead, the new
request function calls finish_fdc() immediately after the last
request has been queued. finish_fdc() executes a dummy seek after
most requests, and this overwrites the state machine's interrupt
hander that was set up to wait for completion of the read/write
request just prior. To make matters worse, finish_fdc() is called
before device interrupts are re-enabled, making certain that the
read/write interupt is missed.
Shifting the finish_fdc() call into the read/write request
completion handler ensures the driver waits for the request to
actually complete. With a queue depth of 2, we won't see long
request sequences, so calling finish_fdc() unconditionally just
adds a little overhead for the dummy seeks, and keeps the code
simple.
While we're at it, kill ataflop_commit_rqs() which does nothing
but run finish_fdc() unconditionally, again likely wiping out an
in-flight request.
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Fixes: 6ec3938cff95 ("ataflop: convert to blk-mq")
CC: linux-block@vger.kernel.org
CC: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Link: https://lore.kernel.org/r/20211019061321.26425-1-schmitzmic@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The variable will be assigned again later in the if condition,
there is no meaning there.
drivers/net/ethernet/broadcom/tg3.c:5750:2 warning:
Value stored to 'current_link_up' is never read.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During the process of driver probing, the probe function should return < 0
for failure, otherwise, the kernel will treat value > 0 as success.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.
Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.
Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.
Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit ea269a6f7207 ("net: phylink: Update SFP selected interface on
advertising changes") added a better solution to selecting the
interface mode for SFPs using the advertisement mask. This method will
work for mvneta and mvpp2 when selecting between 2500base-X and
1000base-X without needing to use the basex helper, or indicate that
we support both 1000base-X and 2500base-X when in either of these two
interface modes.
Hence, we need to eliminate the validation prior to selecting the
interface, otherwise when we clean up mvneta's validation function, we
will end up locking to 2500base-X as we validate with an interface mode
of PHY_INERFACE_MODE_2500BASEX.
The supported mask will already have been reduced down to the union of
support for the SFP and MAC already, so we can be confident that the
advertisement mask is already appropriately restricted. We only need to
select the appropriate interface, and then revalidate with the new
interface mode.
We get rid of the check for pl->sfp_port too, this is meaningless here
as it doesn't get cleared when a module is removed, so it doesn't
indicate if a module is present. Just rely on pl->sfp_bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This assignment statement is meaningless, because the statement
will execute to the tag "set_itr_now".
The clang_analyzer complains as follows:
drivers/net/ethernet/intel/e1000e/netdev.c:2552:3 warning:
Value stored to 'current_itr' is never read.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: luo penghao <luo.penghao@zte.com.cn>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
