summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2021-10-19iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADCCai Huoqing
The NXP i.MX 8QuadXPlus SOC has a new ADC IP, so add driver support for this ADC. Signed-off-by: Cai Huoqing <caihuoqing@baidu.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Link: https://lore.kernel.org/r/20210925020555.129-2-caihuoqing@baidu.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: accel: fxls8962af: add wake on eventSean Nyekjaer
This adds ways for the SoC to wake from accelerometer wake events. In the suspend function we skip disabling the sensor if wakeup-source and events are activated. If buffered reads are enabled they will be deactivated before suspend. As the onboard buffer is only holding up to 32 12-bit X/Y/Z data triplets. Signed-off-by: Sean Nyekjaer <sean@geanix.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210920114221.1595543-2-sean@geanix.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: accel: fxls8962af: add threshold event handlingSean Nyekjaer
Add event channels that control the creation of motion events. Signed-off-by: Sean Nyekjaer <sean@geanix.com> Link: https://lore.kernel.org/r/20210920114221.1595543-1-sean@geanix.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Get and set trimming data.Billy Tsai
The ADC controller has a trimming register for fine-tune the reference voltage. The trimming value comes from the OTP register which will be written during chip production. This patch will read this OTP value and configure it to the ADC register when the ADC controller probes and using dts property "aspeed,trim-data-valid" to determine whether to execute this flow. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-12-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Support battery sensing.Billy Tsai
In ast2600, ADC integrate dividing circuit at last input channel for battery sensing. This patch use the dts property "battery-sensing" to enable this feature makes the last channel of each adc can tolerance higher voltage than reference voltage. The offset interface of ch7 will be separated when enabling the battery sensing mode. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-11-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Add compensation phase.Billy Tsai
This patch adds a compensation phase to improve the accuracy of ADC measurement. This is the built-in function through input half of the reference voltage to get the ADC offset. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-10-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Add func to set sampling rate.Billy Tsai
Add the function to set the sampling rate and keep the sampling period for a driver used to wait the fresh value. In addition, since the ADC clock is required when initializing the ADC device, move clk_prepare_enable ahead of the initialization phase. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-9-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Fix the calculate error of clock.Billy Tsai
The ADC clock formula is ast2400/2500: ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0] + 1) ast2600: ADC clock period = PCLK * 2 * (ADC0C[15:0] + 1) They all have one fixed divided 2 and the legacy driver didn't handle it. This patch register the fixed factory clock device as the parent of ADC clock scaler to fix this issue. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-8-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Support ast2600 adc.Billy Tsai
Make driver to support ast2600 adc device. - Use shared reset controller - Complete the vref configure function - Add the model data for ast2600 adc Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-7-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Use devm_add_action_or_reset.Billy Tsai
This patch use devm_add_action_or_reset to handle the error in probe phase. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-6-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Use model_data to set clk scaler.Billy Tsai
This patch uses need_prescaler and scaler_bit_width to set the ADC clock scaler. Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-5-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Add vref config functionBilly Tsai
Add the function to check the vref_fixed_mv and set the value to driver data. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-4-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Restructure the model dataBilly Tsai
This patch refactors the model data structure to distinguish the function form different versions of aspeed ADC. - Rename the vref_voltage to vref_fixed_mv and add vref_mv driver data When driver probe will check vref_fixed_mv value and store it to vref_mv which isn't const value. - Add num_channels Make num_channles of iio device can be changed by different model_data - Add need_prescaler flag and scaler_bit_width The need_prescaler flag is used to tell the driver the clock divider needs another Prescaler and the scaler_bit_width to set the clock divider bitfield width. Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-3-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: adc: aspeed: Keep model data to driver data.Billy Tsai
Keep the model data pointer to driver data for reducing the usage of of_device_get_match_data(). Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com> Link: https://lore.kernel.org/r/20210922081520.30580-2-billy_tsai@aspeedtech.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19iio: chemical: Add Senseair Sunrise 006-0-007 driverJacopo Mondi
Add support for the Senseair Sunrise 006-0-0007 driver through the IIO subsystem. Datasheet: https://rmtplusstoragesenseair.blob.core.windows.net/docs/Dev/publicerat/TDE5531.pdf Signed-off-by: Jacopo Mondi <jacopo@jmondi.org> Link: https://lore.kernel.org/r/20210920135413.140310-4-jacopo+renesas@jmondi.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2021-10-19media: ite-cir: IR receiver stop working after receive overflowSean Young
On an Intel NUC6iSYK, no IR is reported after a receive overflow. When a receiver overflow occurs, this condition is only cleared by reading the fifo. Make sure we read anything in the fifo. Fixes: 28c7afb07ccf ("media: ite-cir: check for receive overflow") Suggested-by: Bryan Pass <bryan.pass@gmail.com> Tested-by: Bryan Pass <bryan.pass@gmail.com> Cc: stable@vger.kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: sir_ir: remove broken driverSean Young
This driver is a port of the lirc_sir driver to rc-core. However, for this driver I could not find any hardware to test, so it was done without testing. This is a mistake. There are clear bugs in the code. For example the two arguments to ktime_us_delta() are reversed, which means the result is garbage. The driver has been in the kernel for four years, and noone has ever reported an issue. So, remove this driver. Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: ir_toy: assignment to be16 should be of correct typeSean Young
commit f0c15b360fb6 ("media: ir_toy: prevent device from hanging during transmit") removed a cpu_to_be16() cast, which causes a sparse warning. Fixes: f0c15b360fb6 ("media: ir_toy: prevent device from hanging during transmit") Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: ivtv: fix build for UMLRandy Dunlap
Prevent the use of page table macros and types from 2 conflicting places. This fixes multiple build errors and warnings, e.g.: ../arch/x86/include/asm/pgtable_64_types.h:21:34: error: conflicting types for ‘pte_t’ typedef struct { pteval_t pte; } pte_t; ^~~~~ In file included from ../include/linux/mm_types_task.h:16:0, from ../include/linux/mm_types.h:5, from ../include/linux/buildid.h:5, from ../include/linux/module.h:14, from ../drivers/media/pci/ivtv/ivtv-driver.h:40, from ../drivers/media/pci/ivtv/ivtvfb.c:29: ../arch/um/include/asm/page.h:57:39: note: previous declaration of ‘pte_t’ was here typedef struct { unsigned long pte; } pte_t; ../arch/x86/include/asm/pgtable_types.h:284:43: error: expected ‘)’ before ‘prot’ static inline pgprot_t pgprot_nx(pgprot_t prot) ^ ../include/linux/pgtable.h:914:26: note: in definition of macro ‘pgprot_nx’ #define pgprot_nx(prot) (prot) ^~~~ In file included from ../arch/x86/include/asm/memtype.h:6:0, from ../drivers/media/pci/ivtv/ivtvfb.c:40: ../arch/x86/include/asm/pgtable_types.h:288:0: warning: "pgprot_nx" redefined #define pgprot_nx pgprot_nx ../arch/x86/include/asm/page_types.h:11:0: warning: "PAGE_SIZE" redefined #define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT) In file included from ../include/linux/mm_types_task.h:16:0, from ../include/linux/mm_types.h:5, from ../include/linux/buildid.h:5, from ../include/linux/module.h:14, from ../drivers/media/pci/ivtv/ivtv-driver.h:40, from ../drivers/media/pci/ivtv/ivtvfb.c:29: ../arch/um/include/asm/page.h:14:0: note: this is the location of the previous definition #define PAGE_SIZE (_AC(1, UL) << PAGE_SHIFT) Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: Andy Walls <awalls@md.metrocast.net> Cc: linux-um@lists.infradead.org Cc: Richard Weinberger <richard@nod.at> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: cedrus: Don't kernel map most buffersJernej Skrabec
Except for VP8 probability coefficients buffer, all other buffers are never accessed by CPU. That allows us to mark them with DMA_ATTR_NO_KERNEL_MAPPING flag. This helps with decoding big (like 4k) videos on 32-bit ARM platforms where default vmalloc size is relatively small - 240 MiB. Since auxiliary buffer are not yet efficiently allocated, this can be easily exceeded. Even if allocation is optimized, 4k videos will still often exceed this limit. Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: rkvdec: Support dynamic resolution changesChen-Yu Tsai
The mem-to-mem stateless decoder API specifies support for dynamic resolution changes. In particular, the decoder should accept format changes on the OUTPUT queue even when buffers have been allocated, as long as it is not streaming. Relax restrictions for S_FMT as described in the previous paragraph, and as long as the codec format remains the same. This aligns it with the Hantro and Cedrus decoders. This change was mostly based on commit ae02d49493b5 ("media: hantro: Fix s_fmt for dynamic resolution changes"). Since rkvdec_s_fmt() is now just a wrapper around the output/capture variants without any additional shared functionality, drop the wrapper and call the respective functions directly. Fixes: cd33c830448b ("media: rkvdec: Add the rkvdec driver") Cc: <stable@vger.kernel.org> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: rkvdec: Do not override sizeimage for output formatChen-Yu Tsai
The rkvdec H.264 decoder currently overrides sizeimage for the output format. This causes issues when userspace requires and requests a larger buffer, but ends up with one of insufficient size. Instead, only provide a default size if none was requested. This fixes the video_decode_accelerator_tests from Chromium failing on the first frame due to insufficient buffer space. It also aligns the behavior of the rkvdec driver with the Hantro and Cedrus drivers. Fixes: cd33c830448b ("media: rkvdec: Add the rkvdec driver") Cc: <stable@vger.kernel.org> Signed-off-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: imx-jpeg: Add pm-runtime support for imx-jpegMirela Rabulea
Save some power by disabling/enabling the jpeg clocks with every stream stop/start. Do not use DL_FLAG_RPM_ACTIVE in mxc_jpeg_attach_pm_domains, to ensure power domains are off after probe. Signed-off-by: Mirela Rabulea <mirela.rabulea@oss.nxp.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: i.MX6: Support 16-bit BT.1120 video inputKrzysztof Hałasa
Confirmed to work with ADV7610 HDMI receiver. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: Add ADV7610 support for adv7604 driver.Krzysztof Hałasa
ADV7610 is another HDMI receiver chip, very similar to the ADV7611. Also: print chip names in upper case. Fix an error message claiming that no ADV761x has been found, while in reality a chip different than requested (though still supported) may have been found. Tested on TinyRex BaseBoard Lite. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: TDA1997x: replace video detection routineKrzysztof Hałasa
The TDA1997x (HDMI receiver) driver currently uses a specific video format detection scheme. The frame (or field in interlaced mode), line and HSync pulse durations are compared to those of known, standard video modes. If a match is found, the mode is assumed to be detected, otherwise -ERANGE is returned (then possibly ignored). This means that: - another mode with similar timings will be detected incorrectly (e.g. 2x faster clock and lines twice as long) - non-standard modes will not work. This patch replaces this scheme with a direct read of geometry registers. This way all modes recognized by the chip are supported. In interlaced modes, the code assumes the V sync signal has the same duration for both fields. While this may be not necessarily true, I can't see any way to get the "other" V sync width. This is most probably harmless. All tests have been performed on Gateworks' Ventana GW54xx board, with a TDA19971 chip. Signed-off-by: Krzysztof Hałasa <khalasa@piap.pl> Tested-by: Tim Harvey <tharvey@gateworks.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: gspca/gl860-mi1320/ov9655: avoid -Wstring-concatenation warningHans Verkuil
Newer clang versions are suspicious of definitions that mix concatenated strings with comma-separated arrays of strings, this has found real bugs elsewhere, but this seems to be a false positive: drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:37: error: suspicious concatenation of string literals in an array initialization; did you mean to separate the elements with a comma? [-Werror,-Wstring-concatenation] "\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1" ^ , drivers/media/usb/gspca/gl860/gl860-mi1320.c:62:2: note: place parentheses around the string literal to silence warning "\xd3\x02\xd4\x28\xd5\x01\xd0\x02" "\xd1\x18\xd2\xc1" Replace the string literals by compound initializers, using normal hex numbers. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Reported-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: saa7134: Add support for Leadtek WinFast HDTV200 HScott K Logan
Similar configuration to Kworld PC150-U. Tested: Composite, S-Video, NTSC, ATSC Unsupported: IR remote Signed-off-by: Scott K Logan <logans@cottsay.net> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: aspeed: add debugfsJammy Huang
To show video real-time information as below: Capture: Signal : Unlock Width : 1920 Height : 1080 FRC : 30 Performance: Frame# : 0 Frame Duration(ms) : Now : 0 Min : 0 Max : 0 FPS : 0 [hverkuil: make aspeed_video_proc_open() static, fixes sparse warning] Signed-off-by: Jammy Huang <jammy_huang@aspeedtech.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: videobuf2: always set buffer vb2 pointerSergey Senozhatsky
We need to always link allocated vb2_dc_buf back to vb2_buffer because we dereference vb2 in prepare() and finish() callbacks. Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org> Tested-by: Chen-Yu Tsai <wenst@chromium.org> Acked-by: Tomasz Figa <tfiga@chromium.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: rcar-vin: add G/S_PARM ioctlsVladimir Barinov
This adds g/s_parm ioctls for parallel interface. Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: i2c: select V4L2_ASYNC where neededArnd Bergmann
I came across a link failure from randconfig builds: x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_remove': ths8200.c:(.text+0x491): undefined reference to `v4l2_async_unregister_subdev' x86_64-linux-ld: drivers/media/i2c/ths8200.o: in function `ths8200_probe': ths8200.c:(.text+0xe49): undefined reference to `v4l2_async_register_subdev' x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_remove': tw9910.c:(.text+0x467): undefined reference to `v4l2_async_unregister_subdev' x86_64-linux-ld: drivers/media/i2c/tw9910.o: in function `tw9910_probe': tw9910.c:(.text+0x1123): undefined reference to `v4l2_async_register_subdev' These clearly lack a 'select' statement, but I don't know why this started happening only now. I had a bit of a look around to find other configs that have the same problem, but could not come up with a reliable way and found nothing else through experimentation. It is likely that other symbols like these exist that need an extra select. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19media: vidtv: move kfree(dvb) to vidtv_bridge_dev_release()Hans Verkuil
Adding kfree(dvb) to vidtv_bridge_remove() will remove the memory too soon: if an application still has an open filehandle to the device when the driver is unloaded, then when that filehandle is closed, a use-after-free access takes place to the freed memory. Move the kfree(dvb) to vidtv_bridge_dev_release() instead. Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 76e21bb8be4f ("media: vidtv: Fix memory leak in remove") Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2021-10-19Merge tag 'counter-for-5.16a-take2' of ↵Greg Kroah-Hartman
https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next Jonathan writes: First set of counter subsystem new feature support for the 5.16 cycle Most interesting element this time is the new chrdev based interface for the counter subsystem. Affects all drivers. Some minor precursor patches. Major parts: * Bring all the sysfs attribute setup into the counter core rather than leaving it to individual drivers. Docs updates accompany these changes. * Move various definitions to a uapi header as now needed from userspace. * Add the chardev interface + extensive documentation and example tool * Add new ABI needed to identify indexes needed for chrdev interface * Implement new interface for the 104-quad-8 * Follow up deals with wrong path for documentation build * Various trivial cleanups and missing feature additions related to this series * tag 'counter-for-5.16a-take2' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: docs: counter: Include counter-chrdev kernel-doc to generic-counter.rst counter: fix docum. build problems after filename change counter: microchip-tcb-capture: Tidy up a false kernel-doc /** marking. counter: 104-quad-8: Add IRQ support for the ACCES 104-QUAD-8 counter: 104-quad-8: Replace mutex with spinlock counter: Implement events_queue_size sysfs attribute counter: Implement *_component_id sysfs attributes counter: Implement signalZ_action_component_id sysfs attribute tools/counter: Create Counter tools docs: counter: Document character device interface counter: Add character device interface counter: Move counter enums to uapi header docs: counter: Update to reflect sysfs internalization counter: Update counter.h comments to reflect sysfs internalization counter: Internalize sysfs interface code counter: stm32-timer-cnt: Provide defines for slave mode selection counter: stm32-lptimer-cnt: Provide defines for clock polarities
2021-10-18scsi: ufs: ufs-pci: Force a full restore after suspend-to-diskAdrian Hunter
Implement the ->restore() PM operation and set the link to off, which will force a full reset and restore. This ensures that Host Performance Booster is reset after suspend-to-disk. The Host Performance Booster feature caches logical-to-physical mapping information in the host memory. After suspend-to-disk, such information is not valid, so a full reset and restore is needed. A full reset and restore is done if the SPM level is 5 or 6, but not for other SPM levels, so this change fixes those cases. A full reset and restore also restores base address registers, so that code is removed. Link: https://lore.kernel.org/r/20211018151004.284200-2-adrian.hunter@intel.com Reviewed-by: Avri Altman <avri.altman@wdc.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-18scsi: qla2xxx: Fix unmap of already freed sglDmitry Bogdanov
The sgl is freed in the target stack in target_release_cmd_kref() before calling qlt_free_cmd() but there is an unmap of sgl in qlt_free_cmd() that causes a panic if sgl is not yet DMA unmapped: NIP dma_direct_unmap_sg+0xdc/0x180 LR dma_direct_unmap_sg+0xc8/0x180 Call Trace: ql_dbg_prefix+0x68/0xc0 [qla2xxx] (unreliable) dma_unmap_sg_attrs+0x54/0xf0 qlt_unmap_sg.part.19+0x54/0x1c0 [qla2xxx] qlt_free_cmd+0x124/0x1d0 [qla2xxx] tcm_qla2xxx_release_cmd+0x4c/0xa0 [tcm_qla2xxx] target_put_sess_cmd+0x198/0x370 [target_core_mod] transport_generic_free_cmd+0x6c/0x1b0 [target_core_mod] tcm_qla2xxx_complete_free+0x6c/0x90 [tcm_qla2xxx] The sgl may be left unmapped in error cases of response sending. For instance, qlt_rdy_to_xfer() maps sgl and exits when session is being deleted keeping the sgl mapped. This patch removes use-after-free of the sgl and ensures that the sgl is unmapped for any command that was not sent to firmware. Link: https://lore.kernel.org/r/20211018122650.11846-1-d.bogdanov@yadro.com Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Signed-off-by: Dmitry Bogdanov <d.bogdanov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2021-10-18net/mlx5: E-Switch, Increase supported number of forward destinations to 32Maor Dickman
Increase supported number of forward destinations in the same rule, local and remote, from 2 to 32. Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: E-Switch, Use dynamic alloc for dest arrayMaor Dickman
Use dynamic allocation for the dest array in preparation for the next patch which increase MLX5_MAX_FLOW_FWD_VPORTS and will cause stack allocation to be bigger than 1024 bytes. Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Lag, use steering to select the affinity port in LAGMaor Gottlieb
Use the steering based solution for select the affinity port when the LAG mode is based on hash policy and the device support in port selection flow table. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Lag, add support to create/destroy/modify port selectionMaor Gottlieb
Add create function, build the steering tables, TTC and definers according to the LAG hash type. The destroy function, destroys all the steering components. The modify functions is used when the bond mapping changes and it iterates over all the rules in the definers and modifies them to steer the packet to the relevant active ports. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Lag, add support to create TTC tables for LAG port selectionMaor Gottlieb
Add support to create inner and outer TTC tables for LAG port selection. These tables are used to classify the packets in order to select the related definer. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Lag, add support to create definers for LAGMaor Gottlieb
Every definer will consist of a flow table with a single hash group with exactly two flow table entries, one for each device port. The destination of these entries is the uplink vport according to the port state and hash policy. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Lag, set match mask according to the traffic type bitmapMaor Gottlieb
Set the related bits in the match definer mask according to the TT mapping. This mask will be used to create the match definers. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Lag, set LAG traffic type mappingMaor Gottlieb
Generate a traffic type bitmap that will define which steering objects we need to create for the steering based LAG. Bits in this bitmap are set according to the LAG hash type. In addition, have a field that indicate if the lag is in encap mode or not. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Lag, move lag files into directoryMaor Gottlieb
Downstream patches add another lag related file so it makes sense to have all the lag files in a dedicated directory. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Introduce new uplink destination typeMaor Gottlieb
The uplink destination type should be used in rules to steer the packet to the uplink when the device is in steering based LAG mode. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Add support to create match definerMaor Gottlieb
Introduce new APIs to create and destroy flow matcher for given format id. Flow match definer object is used for defining the fields and mask used for the hash calculation. User should mask the desired fields like done in the match criteria. This object is assigned to flow group of type hash. In this flow group type, packets lookup is done based on the hash result. This patch also adds the required bits to create such flow group. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Introduce port selection namespaceMaor Gottlieb
Add new port selection flow steering namespace. Flow steering rules in this namespaceare are used to determine the physical port for egress packets. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18net/mlx5: Support partial TTC rulesMaor Gottlieb
Add bitmasks to ttc_params to indicate if rule is valid or not. It will allow to create TTC table with support only in part of the traffic types. In later patches which introduce the steering based LAG port selection, TTC will be created with only part of the rules according to the hash type. Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
2021-10-18scsi: qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()Joy Gu
Commit 8c0eb596baa5 ("[SCSI] qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()"), intended to change: bsg_job->request->msgcode == FC_BSG_HST_ELS_NOLOGIN to: bsg_job->request->msgcode != FC_BSG_RPT_ELS but changed it to: bsg_job->request->msgcode == FC_BSG_RPT_ELS instead. Change the == to a != to avoid leaking the fcport structure or freeing unallocated memory. Link: https://lore.kernel.org/r/20211012191834.90306-2-jgu@purestorage.com Fixes: 8c0eb596baa5 ("[SCSI] qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Joy Gu <jgu@purestorage.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
generated by cgit (git 2.34.1) at 2025-09-24 13:12:35 +0000