| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds the Alpine MSIX interrupt controller driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Tsahee Zidenberg <tsahee@annapurnalabs.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Always return IRQ_SET_MASK_OK_DONE instead of IRQ_SET_MASK_OK when the
affinity has been updated. When using stacked irqchips, returning
IRQ_SET_MASK_OK_DONE means skipping all descendant irqchips.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The device which is actually does DMA may have a limitation of the maximum
segment size. Respect this setting when preparing scatter-gather list.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Let's defer probing the driver if the return value of
dma_request_slave_channel is ERR_PTR(-EPROBE_DEFER) instead
of disabling dma capability directly.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
dmaengine_terminate_all is deprecated, let's use
dmaengine_terminate_async for interrupt handling.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We should check return value of dmaengine_prep_slave_sg, otherwise
we take risk of null pointer.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
adding unmap of sources and destinations while doing dequeue.
Signed-off-by: Xuelin Shi <xuelin.shi@nxp.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In the Amlogic Meson8 / Meson8b platforms we have two different buses:
cbus and aobus, corresponding to 2 different power domains (regular and
always-on). On each bus a different set of registers is mapped to manage
muxes, GPIOs and in general to control a clear subset of the pins.
Considering this architecture, having two different pinctrl devices, one
for each bus / power domain, makes much more sense than just having one
single device.
Right now we have one single pin controller driver that uses two
different domains (represented by 'gpio' and 'gpio-ao' sub-nodes in the
DTS) to manage the set of registers on the two buses. This dual-domain
configuration is hardcoded into the driver that strictly requires one
domain for each bus in the same pin controller device.
With this patch we refactor the driver to allow splitting the driver in
two parts. This change is needed to have a proper description of the HW
in the device-tree where we want to introduce aobus and cbus.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Separate functions for pins controlled by different pin controllers.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add PCI IDs for Intel Broxton B-Step platform, which have same
LPSS devices with A-Step.
Signed-off-by: Huiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: Qipeng Zha <qipeng.zha@intel.com>
cked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
These drivers can be built as module, so make them depend on I2C rather
than I2C=y.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We forgot to remove the clock tree if something goes wrong in ->probe(). Add a
call to intel_lpss_unregister_clock() on error path in ->probe() to fix the
potential issue.
Fixes: 4b45efe85263 (mfd: Add support for Intel Sunrisepoint LPSS devices)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
tps65010 driver's initcall cannot succeed when the driver is built-in,
because it expects that the I2C probe is completed at initcall time;
this cannot happen as MFD is initialized before I2C. Also on systems
where the chip is not present there is unnecessary 30 ms delay during
the boot.
Instead of waiting for probe to finish, just register the I2C device.
If some boards need retry mechanism for startup glitches, that should be
done in the actual probe function. Also delete the driver banner message.
The patch allows to use tps65010 again with OMAP1 (where it's required
to be built-in) and enables e.g. USB and LED functionality on OMAP5912 OSK.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'ib-mfd-regulator-4.6' and 'ib-mfd-regulator-gpio-4.6' into ibs-for-mfd-merged
|
|
The newly added driver uses do_div() to device a 32-bit number, which now
provokes a warning:
drivers/iio/adc/fsl-imx25-gcq.c: In function 'mx25_gcq_setup_cfgs':
include/asm-generic/div64.h:207:28: warning: comparison of distinct pointer types lacks a cast
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
This replaces the do_div() call with a straight division operator.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6df2e98c3ea5 ("iio: adc: Add imx25-gcq ADC driver")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Introduce PCI_VENDOR/PCI_SUBVENDOR/PCI_SUBDEVICE defines to replace the
constants scattered in the kernel already used to detect QEMU.
They are defined in the QEMU codebase per docs/specs/pci-ids.txt.
Signed-off-by: Robin H. Johnson <robbat2@gentoo.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v4.6-rc1
Here are some cp210x register-accessor updates and general usb-serial
code clean ups.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
git://git.pengutronix.de/git/pza/linux into drm-fixes
ipu-v3 probe and imx-drm crtc and plane fixes
- Fix ipu probe if optional port nodes are not present in the device tree
- Reset the ipu before initializing interrupts, not thereafter
- Notify DRM core about the state of vblank interrupts
- Add missing RGB565 format to the list of plate formats
* tag 'imx-drm-fixes-2016-02-19' of git://git.pengutronix.de/git/pza/linux:
drm/imx: Add missing DRM_FORMAT_RGB565 to ipu_plane_formats
drm/imx: notify DRM core about CRTC vblank state
gpu: ipu-v3: Reset IPU before activating IRQ
gpu: ipu-v3: Do not bail out on missing optional port nodes
|
|
into drm-fixes
radeon and amdgpu fixes for 4.5. Three regression fixes and
some fixups for the error handling in the vblank regression fixes
from earlier.
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
Revert "drm/radeon/pm: adjust display configuration after powerstate"
drm/amdgpu/dp: add back special handling for NUTMEG
drm/radeon/dp: add back special handling for NUTMEG
drm/radeon: Fix error handling in radeon_flip_work_func.
drm/amdgpu: Fix error handling in amdgpu_flip_work_func.
|
|
The at91-pio4 pinctrl driver uses SET_SYSTEM_SLEEP_PM_OPS() to
conditionally set the correct suspend/resume options, but they
become unused when CONFIG_PM is disabled:
drivers/pinctrl/pinctrl-at91-pio4.c:827:12: error: 'atmel_pctrl_suspend' defined but not used [-Werror=unused-function]
drivers/pinctrl/pinctrl-at91-pio4.c:847:12: error: 'atmel_pctrl_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations so the compiler knows
it can silently drop them instead of warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This change will also make Coverity happy by avoiding a theoretical NULL
pointer dereference; yet another reason is to use the above helper function
to tighten the code and make it more readable.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.
gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;
Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.
Fixes: commit 42178e2a1e42 ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current "CONFIG_PINCTRL_UNIPHIER_PH1_*" is too long. It would
not hurt to drop "PH1_" because "UNIPHIER_" already well specifies
the SoC family. Also, rename files for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/sunxi/Kconfig:config PINCTRL_SUN9I_A80_R
drivers/pinctrl/sunxi/Kconfig: def_bool MACH_SUN9I
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/stm32/Kconfig:config PINCTRL_STM32F429
drivers/pinctrl/stm32/Kconfig: bool "STMicroelectronics STM32F429 pin control" if COMPILE_TEST && !MACH_STM32F429
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig / Makefile currently controlling compilation of this code is:
drivers/pinctrl/sh-pfc/Makefile:obj-$(CONFIG_PINCTRL_SH_PFC) += sh-pfc.o
drivers/pinctrl/sh-pfc/Makefile:sh-pfc-objs = core.o pinctrl.o
drivers/pinctrl/sh-pfc/Kconfig:config PINCTRL_SH_PFC
drivers/pinctrl/sh-pfc/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init already wasn't being used in this code, the init
ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/pinctrl/Kconfig:config PINCTRL_MESON
drivers/pinctrl/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Beniamino Galvani <b.galvani@gmail.com>
Cc: Carlo Caione <carlo@endlessm.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Kconfig for this driver is currently:
config PINCTRL_MT6397
bool "Mediatek MT6397 pin control" if COMPILE_TEST && !MFD_MT6397
...meaning that it is currently not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This file is not modular, nor is it using modular functions. The
only thing close is the global THIS_MODULE which comes from export.h
so lets replace it appropriately and cut back on the amount of
header stuff we draw in by several thousand lines.
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch adds support for the mcp23s18 which is very similar to
the mcp23s17. A couple of control bits are not the same.
Notable IOCON_HAEN (s17 only) & IOCON_INTCC. Which can be ignored.
Patch changes the following:
- Add mcp23s18 types.
- Always set mirror bit if the dts defines mcp23s18. regardless of type.
Mirror bit is ignored on 8 bit devices anyway.
- In mcp23s08_probe use chip.ngpio instead of logic based on type
to determine number of gpio lins to increment by. This is set
appropiately by the call to mcp23s08_probe_one.
- Add mcp23s18 to device tree documentation.
- Remove statement that irqs don't work for spi. They do.
Tested with mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The 16Z127 is a 32bit GPIO controller on a MCB FPGA.
Every single line can be configured as input and output.
Push pull and open drain are supported as well as setting
a debounce value for the input lines.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
gicv3_init_bases() is the only caller for its_init(),
also it is a __init function, so mark its_init() as __init too,
then recursively mark the functions called as __init.
This will help to introduce ITS initialization using ACPI tables as
we will use acpi_table_parse_entries family functions there which
belong to __init section as well.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The gic_root_node variable defined in ITS driver is not actually
used, so just remove it.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Following ACPI spec:
On systems supporting GICv3 and above, GICR Base Address in MADT GICC
structure holds the 64-bit physical address of the associated Redistributor.
If all of the GIC Redistributors are in the always-on power domain,
GICR structures should be used to describe the Redistributors instead,
and this field must be set to 0.
It means that we have two ways to initialize registirbutors map.
1. via GICD structure which can accommodate many redistributors as a region
2. via GICC which is able to describe single redistributor
This patch is going to add support for second option.
Considering redistributors, GICD and GICC subtables have be mutually
exclusive. While discovering and mapping redistributor, we need to know
its size in advance. For the GICC case, redistributor can be in
a power-domain that is off, thus we cannot relay on GICR TYPER register.
Therefore, we get GIC version from distributor register and map 2xSZ_64K
for GICv3 and 4xSZ_64K for GICv4.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
With the refator of gic_of_init(), GICv3/4 can be initialized
by gic_init_bases() with gic distributor base address and gic
redistributor region(s).
So get the redistributor region base addresses from MADT GIC
redistributor subtable, and the distributor base address from
GICD subtable to init GICv3 irqchip in ACPI way.
Note: GIC redistributor base address may also be provided in
GICC structures on systems supporting GICv3 and above if the GIC
Redistributors are not in the always-on power domain, this
patch didn't implement such feature yet.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Isolate hardware abstraction (FDT) code to gic_of_init().
Rest of the logic goes to gic_init_bases() and expects well
defined data to initialize GIC properly. The same solution
is used for GICv2 driver.
This is needed for ACPI initialization later.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Create a driver to support the hardware monitoring chip present in
the Zyxel NSA320 and some of the other Zyxel NAS devices.
The driver reads fan speed and temperature from a suitably
pre-programmed MCU on the device.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
[groeck: Dropped .owner field initialization]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The function __spi_pump_messages() is called by spi_pump_messages() and
__spi_sync(). The function __spi_sync() has an argument 'bus_locked'
that indicates if it is called with the SPI bus mutex held or not. If
'bus_locked' is false then __spi_sync() will acquire the mutex itself.
Commit 556351f14e74 ("spi: introduce accelerated read support for spi
flash devices") made a change to acquire the SPI bus mutex within
__spi_pump_messages(). However, this change did not check to see if the
mutex is already held. If __spi_sync() is called with the mutex held
(ie. 'bus_locked' is true), then a deadlock occurs when
__spi_pump_messages() is called.
Fix this deadlock by passing the 'bus_locked' state from __spi_sync() to
__spi_pump_messages() and only acquire the mutex if not already held. In
the case where __spi_pump_messages() is called from spi_pump_messages()
it is assumed that the mutex is not held and so call
__spi_pump_messages() with 'bus_locked' set to false. Finally, move the
unlocking of the mutex to the end of the __spi_pump_messages() function
to simplify the code and only call cond_resched() if there are no
errors.
Fixes: 556351f14e74 ("spi: introduce accelerated read support for spi flash devices")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The implementation of lp3943_gpio_request/lp3943_gpio_free test pin_used
for tracing the pin usage. However, gpiolib already checks FLAG_REQUESTED
flag for the same purpose. So remove the redundant implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
With the current value of cmd_per_lun at 16, the throughput
over a single adapter is limited to around 150kIOPS.
Increase the value of cmd_per_lun to 256 to improve
throughput. With this change a single adapter is able to
attain close to the maximum throughput (380kIOPS).
Also change the number of RRQ entries that can be queued.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When switching to the internal LUN defined on the
IBM CXL flash adapter, there is an unnecessary
scan occurring on the second port. This scan leads
to the following extra lines in the log:
Dec 17 10:09:00 tul83p1 kernel: [ 3708.561134] cxlflash 0008:00:00.0: cxlflash_queuecommand: (scp=c0000000fc1f0f00) 11/1/0/0 cdb=(A0000000-00000000-10000000-00000000)
Dec 17 10:09:00 tul83p1 kernel: [ 3708.561147] process_cmd_err: cmd failed afu_rc=32 scsi_rc=0 fc_rc=0 afu_extra=0xE, scsi_extra=0x0, fc_extra=0x0
By definition, both of the internal LUNs are on the first port/channel.
When the lun_mode is switched to internal LUN the
same value for host->max_channel is retained. This
causes an unnecessary scan over the second port/channel.
This fix alters the host->max_channel to 0 (1 port), if internal
LUNs are configured and switches it back to 1 (2 ports) while
going back to external LUNs.
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In order to support cxlflash in the PowerVM environment, underlying
hypervisor APIs have imposed a kernel API ordering change.
For the superpipe access to LUN, user applications need a context.
The cxlflash module creates this context by making a sequence of
cxl calls. In the current code, a context is initialized via
cxl_dev_context_init() followed by cxl_process_element(), a function
that obtains the process element id. Finally, cxl_start_work()
is called to attach the process element.
In the PowerVM environment, a process element id cannot be obtained
from the hypervisor until the process element is attached. The
cxlflash module is unable to create contexts without a valid
process element id.
To fix this problem, cxl_start_work() is called before obtaining
the process element id.
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The cxlflash_disk_attach() routine currently uses a cascading error
gate strategy for its error cleanup path. While this strategy is
commonly used to handle cleanup scenarios, it is too restrictive when
function callouts need to be restructured. Problems range from
inserting error path bugs in previously 'good' code to the cleanup
path imposing design changes to how the normal path is structured.
A less restrictive approach is needed to support ordering changes
that come about when operating in different environments.
To overcome this restriction, the error cleanup path is modified to
have a single entrypoint and use conditional logic to cleanup where
necessary. Entities that require multiple cleanup steps must be
carefully vetted to ensure their APIs support state. In cases where
they do not (none as of this commit) additional local variables can
be used to maintain state on their behalf.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Presently, context information structures are allocated and
initialized in the same routine, create_context(). This imposes
an ordering restriction such that all pieces of information needed
to initialize a context must be known before the context is even
allocated.
This design point is not flexible when the order of context
creation needs to be modified. Specifically, this can lead to
problems when members of the context information structure are
a part of an ordering dependency (i.e. - the 'work' structure
embedded within the context).
To remedy, the allocation is left as-is, inside of the existing
create_context() routine and the initialization is transitioned
to a new void routine, init_context(). At the same time, in
anticipation of these routines not being called in sequence, a
state boolean is added to the context information structure to
track when the context has been initilized. The context teardown
routine, destroy_context(), is modified to support being called
with a non-initialized context.
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When operating in the PowerVM environment, the cxlflash module can
receive an error from the hypervisor indicating that there are
existing mappings in the page table for the process MMIO space.
This issue exists because term_afu() currently invokes term_mc()
before stop_afu(), allowing for the master context to be detached
first and the problem state area to be unmapped second.
To resolve this issue, stop_afu() should be called before term_mc().
Signed-off-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The calls to pci_request_regions(), pci_resource_start(),
pci_set_dma_mask(), pci_set_master() and pci_save_state() are all
unnecessary for the IBM CXL flash adapter since data buffers
are not required to be mapped to the device's memory.
The use of services such as pci_set_dma_mask() are problematic on
hypervisor managed systems as the IBM CXL flash adapter is operating
under a virtual PCI Host Bridge (virtual PHB) which does not support
these services.
cxlflash 0001:00:00.0: init_pci: Failed to set PCI DMA mask rc=-5
The resolution is to simplify init_pci(), to a point where it does the
bare minimum (pci_enable_device). Similarly, remove the call the
pci_release_regions() from cxlflash_remove().
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Acked-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Reviewed-by: Uma Krishnan <ukrishn@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The pxa2xxx fails some automated builds because of unexported
symbols.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 3209f9d780d1 ("scsi: storvsc: Fix a bug in the handling of SRB
status flags") filtered SRB_STATUS_AUTOSENSE_VALID out effectively making
the (SRB_STATUS_ABORTED | SRB_STATUS_AUTOSENSE_VALID) case a dead code. The
logic from this branch (e.g. storvsc_device_scan() call) is still required,
fix the check.
Cc: <stable@vger.kernel.org> #v4.4+
Fixes: 3209f9d780d1 ("scsi: storvsc: Fix a bug in the handling of SRB status flags")
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
