| Age | Commit message (Collapse) | Author |
|---|
|
In a setup where a Thunderbolt hub connects to Ethernet and a display
through USB Type-C, users may experience a hung task timeout when they
remove the cable between the PC and the Thunderbolt hub.
This is because the igb_down function is called multiple times when
the Thunderbolt hub is unplugged. For example, the igb_io_error_detected
triggers the first call, and the igb_remove triggers the second call.
The second call to igb_down will block at napi_synchronize.
Here's the call trace:
__schedule+0x3b0/0xddb
? __mod_timer+0x164/0x5d3
schedule+0x44/0xa8
schedule_timeout+0xb2/0x2a4
? run_local_timers+0x4e/0x4e
msleep+0x31/0x38
igb_down+0x12c/0x22a [igb 6615058754948bfde0bf01429257eb59f13030d4]
__igb_close+0x6f/0x9c [igb 6615058754948bfde0bf01429257eb59f13030d4]
igb_close+0x23/0x2b [igb 6615058754948bfde0bf01429257eb59f13030d4]
__dev_close_many+0x95/0xec
dev_close_many+0x6e/0x103
unregister_netdevice_many+0x105/0x5b1
unregister_netdevice_queue+0xc2/0x10d
unregister_netdev+0x1c/0x23
igb_remove+0xa7/0x11c [igb 6615058754948bfde0bf01429257eb59f13030d4]
pci_device_remove+0x3f/0x9c
device_release_driver_internal+0xfe/0x1b4
pci_stop_bus_device+0x5b/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_bus_device+0x30/0x7f
pci_stop_and_remove_bus_device+0x12/0x19
pciehp_unconfigure_device+0x76/0xe9
pciehp_disable_slot+0x6e/0x131
pciehp_handle_presence_or_link_change+0x7a/0x3f7
pciehp_ist+0xbe/0x194
irq_thread_fn+0x22/0x4d
? irq_thread+0x1fd/0x1fd
irq_thread+0x17b/0x1fd
? irq_forced_thread_fn+0x5f/0x5f
kthread+0x142/0x153
? __irq_get_irqchip_state+0x46/0x46
? kthread_associate_blkcg+0x71/0x71
ret_from_fork+0x1f/0x30
In this case, igb_io_error_detected detaches the network interface
and requests a PCIE slot reset, however, the PCIE reset callback is
not being invoked and thus the Ethernet connection breaks down.
As the PCIE error in this case is a non-fatal one, requesting a
slot reset can be avoided.
This patch fixes the task hung issue and preserves Ethernet
connection by ignoring non-fatal PCIE errors.
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620174732.4145155-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
According to the errata sheets for ksz9477 and ksz9567, writes to the
PHY registers 0x10-0x1f (i.e. those located at addresses 0xN120 to
0xN13f) must be done as a 32 bit write to the 4-byte aligned address
containing the register, hence requires a RMW in order not to change
the adjacent PHY register.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230620113855.733526-4-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This will be used in a subsequent patch fixing an errata for writes to
certain PHY registers.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-3-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Implement ksz_prmw8() in terms of ksz_rmw8(), just as all the other
ksz_pX are implemented in terms of ksz_X. No functional change.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20230620113855.733526-2-linux@rasmusvillemoes.dk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Half a year passed since commit 049fe5365324c ("net: txgbe: Add operations
to interact with firmware") was submitted, the buffer in
txgbe_calc_eeprom_checksum was not used. So remove it and the related
branch codes.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306200242.FXsHokaJ-lkp@intel.com/
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230620062519.1575298-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix an issue where the kernel would stall during netboot, showing the
"sched: RT throttling activated" message. This stall was triggered by
the behavior of the mii_interrupt bit (Bit 7 - DP83TD510E_STS_MII_INT)
in the DP83TD510E's PHY_STS Register (Address = 0x10). The DP83TD510E
datasheet (2020) states that the bit clears on write, however, in
practice, the bit clears on read.
This discrepancy had significant implications on the driver's interrupt
handling. The PHY_STS Register was used by handle_interrupt() to check
for pending interrupts and by read_status() to get the current link
status. The call to read_status() was unintentionally clearing the
mii_interrupt status bit without deasserting the IRQ pin, causing
handle_interrupt() to miss other pending interrupts. This issue was most
apparent during netboot.
The fix refrains from using the PHY_STS Register for interrupt handling.
Instead, we now solely rely on the INTERRUPT_REG_1 Register (Address =
0x12) and INTERRUPT_REG_2 Register (Address = 0x13) for this purpose.
These registers directly influence the IRQ pin state and are latched
high until read.
Note: The INTERRUPT_REG_2 Register (Address = 0x13) exists and can also
be used for interrupt handling, specifically for "Aneg page received
interrupt" and "Polarity change interrupt". However, these features are
currently not supported by this driver.
Fixes: 165cd04fe253 ("net: phy: dp83td510: Add support for the DP83TD510 Ethernet PHY")
Cc: <stable@vger.kernel.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230621043848.3806124-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update macb's embedded PCS drivers to use neg_mode, even though it
makes no use of it or the "mode" argument. This makes the driver
consistent with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Eo-00EaGX-KJ@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mt7530's embedded PCS driver to use neg_mode, even though it
makes no use of it or the "mode" argument. This makes the driver
consistent with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Ej-00EaGR-Fk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update B53's embedded PCS driver to use neg_mode, even though it makes
no use of it or the "mode" argument. This makes the driver consistent
with converted drivers.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1qA8Ee-00EaGL-Az@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update Sparx5's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EZ-00EaGF-6F@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update qca8k's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EU-00EaG9-1l@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update prestera's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Acked-by: Elad Nachman <enachman@marvell.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EO-00EaG3-TR@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mvpp2's embedded PCS drivers to use neg_mode rather than the
mode argument, remembering to update the ACPI path as well. As there
are no pcs_link_up() methods, this only affects the two pcs_config()
methods.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EJ-00EaFx-P6@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update mvneta's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8EE-00EaFr-Kx@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update lan966x's embedded PCS driver to use neg_mode rather than the
mode argument. As there is no pcs_link_up() method, this only affects
the pcs_config() method.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E9-00EaFl-GN@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the Lynx PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8E4-00EaFf-Bf@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the Lynxi PCS driver to use neg_mode rather than the mode
argument. This ensures that the link_up() method will always program
the speed and duplex when negotiation is disabled.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dz-00EaFY-5A@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update xpcs to use neg_mode to configure whether inband negotiation
should be used. We need to update sja1105 as well as that directly
calls into the XPCS driver's config function.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dt-00EaFS-W9@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Convert fman_dtsec, xilinx_axienet and pcs-lynx to pass the neg_mode
into phylink_mii_c22_pcs_config(). Where appropriate, drivers are
updated to have neg_mode passed into their pcs_config() and
pcs_link_up() functions. For other drivers, we just hoist the call
to phylink_pcs_neg_mode() to their pcs_config() method out of
phylink_mii_c22_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Do-00EaFM-Ra@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use phylink_pcs_neg_mode() for phylink_mii_c22_pcs_config(). This
results in no functional change.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8Dj-00EaFG-Mt@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PCS have to work out whether they should enable PCS negotiation by
looking at the "mode" and "interface" arguments, and the Autoneg bit
in the advertising mask.
This leads to some complex logic, so lets pull that out into phylink
and instead pass a "neg_mode" argument to the PCS configuration and
link up methods, instead of the "mode" argument.
In order to transition drivers, add a "neg_mode" flag to the phylink
PCS structure to PCS can indicate whether they want to be passed the
neg_mode or the old mode argument.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1qA8De-00EaFA-Ht@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Spell "transmission" properly.
Found by searching for keyword "tranm".
Signed-off-by: Yueh-Shun Li <shamrocklee@posteo.net>
Link: https://lore.kernel.org/r/20230622012627.15050-3-shamrocklee@posteo.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 49725ffc15fc ("net: stmmac: power up/down serdes in
stmmac_open/release") correctly added a call to the serdes_powerdown()
callback to stmmac_release() but did not remove the one from
stmmac_remove() which leads to a doubled call to serdes_powerdown().
This can lead to all kinds of problems: in the case of the qcom ethqos
driver, it caused an unbalanced regulator disable splat.
Fixes: 49725ffc15fc ("net: stmmac: power up/down serdes in stmmac_open/release")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Acked-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20230621135537.376649-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
tools/testing/selftests/net/fcnal-test.sh
d7a2fc1437f7 ("selftests: net: fcnal-test: check if FIPS mode is enabled")
dd017c72dde6 ("selftests: fcnal: Test SO_DONTROUTE on TCP sockets.")
https://lore.kernel.org/all/5007b52c-dd16-dbf6-8d64-b9701bfa498b@tessares.net/
https://lore.kernel.org/all/20230619105427.4a0df9b3@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from ipsec, bpf, mptcp and netfilter.
Current release - regressions:
- netfilter: add NFT_TRANS_PREPARE_ERROR to deal with bound set/chain
- eth: mlx5e:
- fix scheduling of IPsec ASO query while in atomic
- free IRQ rmap and notifier on kernel shutdown
Current release - new code bugs:
- phy: manual remove LEDs to ensure correct ordering
Previous releases - regressions:
- mptcp: fix possible divide by zero in recvmsg()
- dsa: revert "net: phy: dp83867: perform soft reset and retain
established link"
Previous releases - always broken:
- sched: netem: acquire qdisc lock in netem_change()
- bpf:
- fix verifier id tracking of scalars on spill
- fix NULL dereference on exceptions
- accept function names that contain dots
- netfilter: disallow element updates of bound anonymous sets
- mptcp: ensure listener is unhashed before updating the sk status
- xfrm:
- add missed call to delete offloaded policies
- fix inbound ipv4/udp/esp packets to UDPv6 dualstack sockets
- selftests: fixes for FIPS mode
- dsa: mt7530: fix multiple CPU ports, BPDU and LLDP handling
- eth: sfc: use budget for TX completions
Misc:
- wifi: iwlwifi: add support for SO-F device with PCI id 0x7AF0"
* tag 'net-6.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits)
revert "net: align SO_RCVMARK required privileges with SO_MARK"
net: wwan: iosm: Convert single instance struct member to flexible array
sch_netem: acquire qdisc lock in netem_change()
selftests: forwarding: Fix race condition in mirror installation
wifi: mac80211: report all unusable beacon frames
mptcp: ensure listener is unhashed before updating the sk status
mptcp: drop legacy code around RX EOF
mptcp: consolidate fallback and non fallback state machine
mptcp: fix possible list corruption on passive MPJ
mptcp: fix possible divide by zero in recvmsg()
mptcp: handle correctly disconnect() failures
bpf: Force kprobe multi expected_attach_type for kprobe_multi link
bpf/btf: Accept function names that contain dots
Revert "net: phy: dp83867: perform soft reset and retain established link"
net: mdio: fix the wrong parameters
netfilter: nf_tables: Fix for deleting base chains with payload
netfilter: nfnetlink_osf: fix module autoload
netfilter: nf_tables: drop module reference after updating chain
netfilter: nf_tables: disallow timeout for anonymous sets
netfilter: nf_tables: disallow updates of anonymous sets
...
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why
Generic:
- Avoid setting page table entries pointing to a deleted memslot if a
host page table entry is changed concurrently with the deletion"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: Avoid illegal stage2 mapping on invalid memory slot
KVM: arm64: Use raw_smp_processor_id() in kvm_pmu_probe_armpmu()
KVM: arm64: Restore GICv2-on-GICv3 functionality
KVM: arm64: PMU: Don't overwrite PMUSERENR with vcpu loaded
KVM: arm64: PMU: Restore the host's PMUSERENR_EL0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix support for deferred probing for several host drivers
- litex_mmc: Use async probe as it's common for all mmc hosts
- meson-gx: Fix bug when scheduling while atomic
- mmci_stm32: Fix max busy timeout calculation
- sdhci-msm: Disable broken 64-bit DMA on MSM8916
* tag 'mmc-v6.4-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: usdhi60rol0: fix deferred probing
mmc: sunxi: fix deferred probing
mmc: sh_mmcif: fix deferred probing
mmc: sdhci-spear: fix deferred probing
mmc: sdhci-acpi: fix deferred probing
mmc: owl: fix deferred probing
mmc: omap_hsmmc: fix deferred probing
mmc: omap: fix deferred probing
mmc: mvsdio: fix deferred probing
mmc: mtk-sd: fix deferred probing
mmc: meson-gx: fix deferred probing
mmc: bcm2835: fix deferred probing
mmc: litex_mmc: set PROBE_PREFER_ASYNCHRONOUS
mmc: meson-gx: remove redundant mmc_request_done() call from irq context
mmc: mmci: stm32: fix max busy timeout calculation
mmc: sdhci-msm: Disable broken 64-bit DMA on MSM8916
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver fix from Hans de Goede:
"One small fix for an AMD PMF driver issue which is causing issues for
users of just released AMD laptop models"
* tag 'platform-drivers-x86-v6.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/amd/pmf: Register notify handler only if SPS is enabled
|
|
Merge series from Miquel Raynal <miquel.raynal@bootlin.com>:
I recently came across an issue with the Atmel spi controller driver
which would stop my transfers after a too small timeout when performing
big transfers (reading a 4MiB flash in one transfer). My initial idea
was to derive a the maximum amount of time a transfer would take
depending on its size and use that as value to avoid erroring-out when
not relevant. Mark wanted to go further by creating a core helper doing
that, based on the heuristics from the sun6i driver.
Here is a small series of 3 patches doing exactly that.
|
|
A helper was recently added to the core to factorize common code between
drivers, like the amount of time a driver should wait for a transfer to
happen.
It is of course possible to use a default value (like eg. 1s) but it is
way stronger to adapt this amount of time to the transfer. Indeed, long
transfers (eg. 4MiB) on a slow single-spi bus might take more than the
usual second of timeout and prevent lengthy transfers.
The core helper was heavily inspired by the logic applied in this
driver, the only difference being the minimum amount of time which was
enlarged from 0.1s to 0.5s.
Use this helper instead of open-coding it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jernej Škrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-4-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A slow SPI bus clocks at ~20MHz, which means it would transfer about
2500 bytes per second with a single data line. Big transfers, like when
dealing with flashes can easily reach a few MiB. The current DMA timeout
is set to 1 second, which means any working transfer of about 4MiB will
always be cancelled.
With the above derivations, on a slow bus, we can assume every byte will
take at most 0.4ms. Said otherwise, we could add 4ms to the 1-second
timeout delay every 10kiB. On a 4MiB transfer, it would bring the
timeout delay up to 2.6s which still seems rather acceptable for a
timeout.
The consequence of this is that long transfers might be allowed, which
hence requires the need to interrupt the transfer if wanted by the
user. We can hence switch to the _interruptible variant of
wait_for_completion. This leads to a little bit more handling to also
handle the interrupted case but looks really acceptable overall.
While at it, we drop the useless, noisy and redundant WARN_ON() call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ryan Wanner <ryan.wanner@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-3-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix typo in the description of the 'succesfull'.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230621020331.1508-1-wangdeming@inspur.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.4, take #4
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why...
|
|
ice_change_mtu() is currently using a separate ice_down() and ice_up()
calls to reflect changed MTU. ice_down_up() serves this purpose, so do
the refactoring here.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is no need to use managed memory allocation here. The memory is
released at the end of the function.
Use kzalloc()/kfree() to simplify the code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support for reading PWM values and mode,
and update documentation accordingly.
Signed-off-by: Wilken Gottwalt <wilken.gottwalt@posteo.net>
Link: https://lore.kernel.org/r/ZJSASByXpzoZ0XyH@monster.localdomain
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
According to ADI, changing PMON_CONFIG while the ADC is running can have
unexpected results. ADI recommends halting the ADC with PMON_CONTROL
before setting PMON_CONFIG and then resume after. Follow ADI
recommendation and disable ADC while PMON_CONFIG is updated.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230614163605.3688964-3-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
According to ADI, changing PMON_CONFIG while ADC is running can have
unexpected results. ADI recommends halting the ADC with PMON_CONTROL
before setting PMON_CONFIG and then resume after.
To prepare for this change, rename adm1275_read_pmon_config()
and adm1275_write_pmon_config() to adm1275_read_samples() and
adm1275_write_samples() to more accurately reflect the functionality
of the code. Introduce new function adm1275_write_pmon_config()
and use it for all code writing into the PMON_CONFIG register.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230614163605.3688964-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix the following fallthrough warnings seen after building sh
architecture with sh7763rdp_defconfig configuration:
drivers/video/fbdev/sh7760fb.c: In function 'sh7760fb_get_color_info':
drivers/video/fbdev/sh7760fb.c:138:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
138 | lgray = 1;
| ~~~~~~^~~
drivers/video/fbdev/sh7760fb.c:139:9: note: here
139 | case LDDFR_4BPP:
| ^~~~
drivers/video/fbdev/sh7760fb.c:143:23: warning: this statement may fall through [-Wimplicit-fallthrough=]
143 | lgray = 1;
| ~~~~~~^~~
drivers/video/fbdev/sh7760fb.c:144:9: note: here
144 | case LDDFR_8BPP:
| ^~~~
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When configurating a CHn Source Image Format Register (LDBBSIFR), one
should use the corresponding LDBBSIFR_RPKF_* definition for overlay
planes, not the DDFR_PKF_* definition for the primary plane.
Fortunately both definitions resolve to the same value, so this bug did
not cause any harm.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
We all know they are redundant.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The check for existing VFs was redundant since very
inception of SR-IOV sysfs interface in the kernel,
see commit 1789382a72a5 ("PCI: SRIOV control and status via sysfs").
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently ice driver's .ndo_bpf callback brings interface down and up
independently of XDP resources' presence. This is only needed when
either these resources have to be configured or removed. It means that
if one is switching XDP programs on-the-fly with running traffic,
packets will be dropped.
To avoid this, compare early on ice_xdp_setup_prog() state of incoming
bpf_prog pointer vs the bpf_prog pointer that is already assigned to
VSI. Do the swap in case VSI has bpf_prog and incoming one are non-NULL.
Lastly, while at it, put old bpf_prog *after* the update of Rx ring's
bpf_prog pointer. In theory previous code could expose us to a state
where Rx ring's bpf_prog would still be referring to old_prog that got
released with earlier bpf_prog_put().
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_sq_send_cmd() function is used to send messages to the control
queues used to communicate with firmware, virtual functions, and even some
hardware.
When sending a control queue message, the driver is designed to
synchronously wait for a response from the queue. Currently it waits
between checks for 100 to 150 microseconds.
Commit f86d6f9c49f6 ("ice: sleep, don't busy-wait, for
ICE_CTL_Q_SQ_CMD_TIMEOUT") did recently change the behavior from an
unnecessary delay into a sleep which is a significant improvement over the
old behavior of polling using udelay.
Because of the nature of PCIe transactions, the hardware won't be informed
about a new message until the write to the tail register posts. This is
only guaranteed to occur at the next register read. In ice_sq_send_cmd(),
this happens at the ice_sq_done() call. Because of this, the driver
essentially forces a minimum of one full wait time regardless of how fast
the response is.
For the hardware-based sideband queue, this is especially slow. It is
expected that the hardware will respond within 2 or 3 microseconds, an
order of magnitude faster than the 100-150 microsecond sleep.
Allow such fast completions to occur without delay by introducing a small 5
microsecond delay first before entering the sleeping timeout loop. Ensure
the tail write has been posted by using ice_flush(hw) first.
While at it, lets also remove the ICE_CTL_Q_SQ_CMD_USEC macro as it
obscures the sleep time in the inner loop. It was likely introduced to
avoid "magic numbers", but in practice sleep and delay values are easier to
read and understand when using actual numbers instead of a named constant.
This change should allow the fast hardware based control queue messages to
complete quickly without delay, while slower firmware queue response times
will sleep while waiting for the response.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Make all possible functions static.
Move iavf_force_wb() up to avoid forward declaration.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove iavf_aq_get_rss_lut(), iavf_aq_get_rss_key(), iavf_vf_reset().
Remove some "OS specific memory free for shared code" wrappers ;)
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Defer removal of current primary MAC until a replacement is successfully
added. Previous implementation would left filter list with no primary MAC.
This was found while reading the code.
The patch takes advantage of the fact that there can only be a single primary
MAC filter at any time ([1] by Piotr)
Piotr has also applied some review suggestions during our internal patch
submittal process.
[1] https://lore.kernel.org/netdev/20230614145302.902301-2-piotrx.gardocki@intel.com/
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The Dell Studio 1569 predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native intel_backlight interface which
does work properly.
Reported-by: raycekarneal <raycekarneal@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There's an hardware issue that can cause missing timestamps. The bug
is that the interrupt is only cleared if the IGC_TXSTMPH_0 register is
read.
The bug can cause a race condition if a timestamp is captured at the
wrong time, and we will miss that timestamp. To reduce the time window
that the problem is able to happen, in case no timestamp was ready, we
read the "previous" value of the timestamp registers, and we compare
with the "current" one, if it didn't change we can be reasonably sure
that no timestamp was captured. If they are different, we use the new
value as the captured timestamp.
The HW bug is not easy to reproduce, got to reproduce it when smashing
the NIC with timestamping requests from multiple applications (e.g.
multiple ntpperf instances + ptp4l), after 10s of minutes.
This workaround has more impact when multiple timestamp registers are
used, and the IGC_TXSTMPH_0 register always need to be read, so the
interrupt is cleared.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the interrupt is handled, the TXTT_0 bit in the TSYNCTXCTL
register should already be set and the timestamp value already loaded
in the appropriate register.
This simplifies the handling, and reduces the latency for retrieving
the TX timestamp, which increase the amount of TX timestamps that can
be handled in a given time period.
As the "work" function doesn't run in a workqueue anymore, rename it
to something more sensible, a event handler.
Using ntpperf[1] we can see the following performance improvements:
Before:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -56 +9 +52 19
1500 150 0.00% 0.00% 0.00% 100.00% -40 +30 +75 22
2250 225 0.00% 0.00% 0.00% 100.00% -11 +29 +72 15
3375 337 0.00% 0.00% 0.00% 100.00% -18 +40 +88 22
5062 506 0.00% 0.00% 0.00% 100.00% -19 +23 +77 15
7593 759 0.00% 0.00% 0.00% 100.00% +7 +47 +5168 43
11389 1138 0.00% 0.00% 0.00% 100.00% -11 +41 +5240 39
17083 1708 0.00% 0.00% 0.00% 100.00% +19 +60 +5288 50
25624 2562 0.00% 0.00% 0.00% 100.00% +1 +56 +5368 58
38436 3843 0.00% 0.00% 0.00% 100.00% -84 +12 +8847 66
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 0.00% 0.00% 100.00% 0.00%
291871 16384 27.35% 0.00% 72.65% 0.00%
437806 16384 50.05% 0.00% 49.95% 0.00%
After:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -44 +0 +61 19
1500 150 0.00% 0.00% 0.00% 100.00% -6 +39 +81 16
2250 225 0.00% 0.00% 0.00% 100.00% -22 +25 +69 15
3375 337 0.00% 0.00% 0.00% 100.00% -28 +15 +56 14
5062 506 0.00% 0.00% 0.00% 100.00% +7 +78 +143 27
7593 759 0.00% 0.00% 0.00% 100.00% -54 +24 +144 47
11389 1138 0.00% 0.00% 0.00% 100.00% -90 -33 +28 21
17083 1708 0.00% 0.00% 0.00% 100.00% -50 -2 +35 14
25624 2562 0.00% 0.00% 0.00% 100.00% -62 +7 +66 23
38436 3843 0.00% 0.00% 0.00% 100.00% -33 +30 +5395 36
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 19.50% 0.00% 80.50% 0.00%
291871 16384 35.81% 0.00% 64.19% 0.00%
437806 16384 55.40% 0.00% 44.60% 0.00%
[1] https://github.com/mlichvar/ntpperf
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
