| Age | Commit message (Collapse) | Author |
|---|
|
0x7d and 0x7e bytes are meant to be escaped in the data portion of
frames, but this didn't occur since next_chunk_len() had an off-by-one
error. That also resulted in the final byte of a payload being written
as a separate tty write op.
The chunk prior to an escaped byte would be one byte short, and the
next call would never test the txpos+1 case, which is where the escaped
byte was located. That meant it never hit the escaping case in
mctp_serial_tx_work().
Example Input: 01 00 08 c8 7e 80 02
Previous incorrect chunks from next_chunk_len():
01 00 08
c8 7e 80
02
With this fix:
01 00 08 c8
7e
80 02
Cc: stable@vger.kernel.org
Fixes: a0c2ccd9b5ad ("mctp: Add MCTP-over-serial transport binding")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Test various edge cases of inputs that contain characters
that need escaping.
This adds a new kunit suite for mctp-serial.
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the LTC2991, V5 and V6 channels use the low nibble of the
"V5, V6, V7, and V8 Control Register" for configuration, but currently,
the high nibble is defined.
This patch changes the defines to use the low nibble.
Fixes: 2b9ea4262ae9 ("hwmon: Add driver for ltc2991")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Message-ID: <20240830111349.30531-1-paweldembicki@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull power sequencing fix from Bartosz Golaszewski:
"A follow-up fix for the power sequencing subsystem. It turned out the
previous fix for this driver was incomplete and broke the WLAN support
on some platforms. This addresses the issue.
- set the direction of the wlan-enable GPIO to output after
requesting it as-is"
* tag 'pwrseq-fixes-for-v6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
power: sequencing: qcom-wcn: set the wlan-enable GPIO to output
|
|
Commit a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO
as-is") broke WLAN on boards on which the wlan-enable GPIO enabling the
wifi module isn't in output mode by default. We need to set direction to
output while retaining the value that was already set to keep the ath
module on if it's already started.
Fixes: a9aaf1ff88a8 ("power: sequencing: request the WLAN enable GPIO as-is")
Link: https://lore.kernel.org/r/20240823115500.37280-1-brgl@bgdev.pl
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 6.11-rc6. Included in here are:
- dwc3 driver fixes for reported issues
- MAINTAINER file update, marking a driver as unsupported :(
- cdnsp driver fixes
- USB gadget driver fix
- USB sysfs fix
- other tiny fixes
- new device ids for usb serial driver
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: serial: option: add MeiG Smart SRM825L
usb: cdnsp: fix for Link TRB with TC
usb: dwc3: st: add missing depopulate in probe error path
usb: dwc3: st: fix probed platform device ref count on probe error path
usb: dwc3: ep0: Don't reset resource alloc flag (including ep0)
usb: core: sysfs: Unmerge @usb3_hardware_lpm_attr_group in remove_power_attributes()
usb: typec: fsa4480: Relax CHIP_ID check
usb: dwc3: xilinx: add missing depopulate in probe error path
usb: dwc3: omap: add missing depopulate in probe error path
dt-bindings: usb: microchip,usb2514: Fix reference USB device schema
usb: gadget: uvc: queue pump work in uvcg_video_enable()
cdc-acm: Add DISABLE_ECHO quirk for GE HealthCare UI Controller
usb: cdnsp: fix incorrect index in cdnsp_get_hw_deq function
usb: dwc3: core: Prevent USB core invalid event buffer address access
MAINTAINERS: Mark UVC gadget driver as orphan
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Minor fixes only.
The sd.c one ignores a sync cache request if format is in progress
which can happen if formatting a drive across suspend/resume"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Ignore command SYNCHRONIZE CACHE error if format in progress
scsi: aacraid: Fix double-free on probe failure
scsi: lpfc: Fix overflow build issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There is a fairly large number of bug fixes for Qualcomm platforms,
most of them addressing issues with the devicetree files for the newly
added Snapdragon X1 based laptops to make them more reliable.
The Qualcomm driver changes address a few build-time issues as well as
runtime problems in the tzmem and scm firmware, the USB Type-C driver,
and the cmd-db and pmic_glink soc drivers.
The NXP i.MX usually gets a bunch of devicetree fixes that is
proportional to the number of supported machines. This includes both
warning fixes and correctness for the 64-bit i.MX9, i.MX8 and
layerscape platforms, as well as a single fix for a 32-bit i.MX6 based
board.
The other changes are the usual minor changes, including an update to
the MAINTAINERS file, an omap3 dts file and a SoC driver for mpfs
(risc-v)"
* tag 'arm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
firmware: microchip: fix incorrect error report of programming:timeout on success
soc: qcom: pd-mapper: Fix singleton refcount
firmware: qcom: tzmem: disable sdm670 platform
soc: qcom: pmic_glink: Actually communicate when remote goes down
usb: typec: ucsi: Move unregister out of atomic section
soc: qcom: pmic_glink: Fix race during initialization
firmware: qcom: qseecom: remove unused functions
firmware: qcom: tzmem: fix virtual-to-physical address conversion
firmware: qcom: scm: Mark get_wq_ctx() as atomic call
arm64: dts: qcom: x1e80100: Fix Adreno SMMU global interrupt
arm64: dts: qcom: disable GPU on x1e80100 by default
arm64: dts: imx8mm-phygate: fix typo pinctrcl-0
arm64: dts: imx95: correct L3Cache cache-sets
arm64: dts: imx95: correct a55 power-domains
arm64: dts: freescale: imx93-tqma9352-mba93xxla: fix typo
arm64: dts: freescale: imx93-tqma9352: fix CMA alloc-ranges
ARM: dts: imx6dl-yapp43: Increase LED current to match the yapp4 HW design
arm64: dts: imx93: update default value for snps,clk-csr
arm64: dts: freescale: tqma9352: Fix watchdog reset
arm64: dts: imx8mp-beacon-kit: Fix Stereo Audio on WM8962
...
|
|
Unmask the upper DSCP bits when calling ip_route_output_flow() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Unmask the upper DSCP bits when calling ip_route_output_flow() so that
in the future it could perform the FIB lookup according to the full DSCP
value.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
- a fix for Cypress PS/2 touchpad for regression introduced in 6.11
merge window where a timeout condition is incorrectly reported for
all extended Cypress commands
* tag 'input-for-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cypress_ps2 - fix waiting for command response
|
|
If the __qcuefi pointer is not set, then in the original code, we would
hold onto the lock. That means that if we tried to set it later, then
it would cause a deadlock. Drop the lock on the error path. That's
what all the callers are expecting.
Fixes: 759e7a2b62eb ("firmware: Add support for Qualcomm UEFI Secure Application")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/19829bc4-1b6f-47f7-847a-e90c25749e40@stanley.mountain
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci fixes from Bjorn Helgaas:
- Add Manivannan Sadhasivam as PCI native host bridge and endpoint
driver reviewer (Manivannan Sadhasivam)
- Disable MHI RAM data parity error interrupt for qcom SA8775P SoC to
work around hardware erratum that causes a constant stream of
interrupts (Manivannan Sadhasivam)
- Don't try to fall back to qcom Operating Performance Points (OPP)
support unless the platform actually supports OPP (Manivannan
Sadhasivam)
- Add imx@lists.linux.dev mailing list to MAINTAINERS for NXP
layerscape and imx6 PCI controller drivers (Frank Li)
* tag 'pci-v6.11-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
MAINTAINERS: PCI: Add NXP PCI controller mailing list imx@lists.linux.dev
PCI: qcom: Use OPP only if the platform supports it
PCI: qcom-ep: Disable MHI RAM data parity error interrupt for SA8775P SoC
MAINTAINERS: Add Manivannan Sadhasivam as Reviewer for PCI native host bridge and endpoint drivers
|
|
This aligns with what open gpu does, the 0x15 hex is just to trick you.
Fixes: 176fdcbddfd2 ("drm/nouveau/gsp/r535: add support for booting GSP-RM")
Reviewed-by: Ben Skeggs <bskeggs@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Danilo Krummrich <dakr@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240828023720.1596602-1-airlied@gmail.com
|
|
On systems in the field, we are seeing this sometimes in the kernel logs:
Bluetooth: qca_controller_memdump() hci0: hci_devcd_init Return:-95
This means that _something_ decided that it wanted to get a memdump
but then hci_devcd_init() returned -EOPNOTSUPP (AKA -95).
The cleanup code in qca_controller_memdump() when we get back an error
from hci_devcd_init() undoes most things but forgets to clear
QCA_IBS_DISABLED. One side effect of this is that, during the next
suspend, qca_suspend() will always get a timeout.
Let's fix it so that we clear the bit.
Fixes: 06d3fdfcdf5c ("Bluetooth: hci_qca: Add qcom devcoredump support")
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
Kvaser's PCIe cards uses the KCAN FPGA IP block which has dual 4K
buffers for incoming messages shared by all (currently up to eight)
channels. While the driver processes messages in one buffer, new
incoming messages are stored in the other and so on.
The design of KCAN is such that a buffer must be fully read and then
released. Releasing a buffer will make the FPGA switch buffers. If the
other buffer contains at least one incoming message the FPGA will also
instantly issue a new interrupt, if not the interrupt will be issued
after receiving the first new message.
With IRQx interrupts, it takes a little time for the interrupt to
happen, enough for any previous ISR call to do it's business and
return, but MSI interrupts are way faster so this time is reduced to
almost nothing.
So with MSI, releasing the buffer HAS to be the very last action of
the ISR before returning, otherwise the new interrupt might be
"masked" by the kernel because the previous ISR call hasn't returned.
And the interrupts are edge-triggered so we cannot loose one, or the
ping-pong reading process will stop.
This is why this patch modifies the driver to use a single write to
the SRB_CMD register before returning.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20240830153113.2081440-1-martin.jocic@kvaser.com
Fixes: 26ad340e582d ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
dev_err_probe() is used to log an error message during the probe process
of a device.
It can simplify the error path and unify a message template.
Using this helper is totally fine even if err is known to never
be -EPROBE_DEFER.
The benefit compared to a normal dev_err() is the standardized format
of the error code, it being emitted symbolically and the fact that
the error code is returned which allows more compact error paths.
Signed-off-by: Yan Zhen <yanzhen@vivo.com>
Link: https://patch.msgid.link/20240830110651.519119-1-yanzhen@vivo.com
mkl: fix indention
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the IS_ENABLED() macro to check kernel config defines instead of
ifdef. Use upper_32_bits() to avoid warnings about "right shift count
>= width of type" on systems with CONFIG_ARCH_DMA_ADDR_T_64BIT not
set. In kvaser_pciefd_write_dma_map_altera() use lower_32_bits() for
symmetry.
Signed-off-by: Martin Jocic <martin.jocic@kvaser.com>
Link: https://patch.msgid.link/20240830141038.1402217-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_priv::ctrlmode
This patch moves the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_changelink in front of the evaluation of data[IFLA_CAN_BITTIMING].
This avoids a call to do_set_data_bittiming providing a stale
can_priv::ctrlmode with a CAN_CTRLMODE_FD flag not matching the
requested state when switching between a CAN Classic and CAN-FD bitrate.
In the same manner the evaluation of data[IFLA_CAN_CTRLMODE] in function
can_validate is also moved in front of the evaluation of
data[IFLA_CAN_BITTIMING].
This is a preparation for patches where the nominal and data bittiming
may have interdependencies on the driver side depending on the
CAN_CTRLMODE_FD flag state.
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Link: https://patch.msgid.link/20240808164224.213522-1-stefan.maetje@esd.eu
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add "EEE: Enabled/Disabled" to dmesg for supported X710 Base-T/KR/KX
cards. According to the IEEE standard report the EEE ability and the
EEE Link Partner ability. Use the kernel's 'ethtool_keee' structure
and report EEE link modes.
Example:
dmesg | grep 'NIC Link is'
ethtool --show-eee <device>
Before:
NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None
Supported EEE link modes: Not reported
Advertised EEE link modes: Not reported
Link partner advertised EEE link modes: Not reported
After:
NIC Link is Up, 10 Gbps Full Duplex, Flow Control: None, EEE: Enabled
Supported EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Link partner advertised EEE link modes: 100baseT/Full
1000baseT/Full
10000baseT/Full
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Occasionally when the system goes into pm_suspend, the suspend might fail
due to a PHY access error on the network adapter. Previously, this would
have caused the whole system to fail to go to a low power state.
An example of this was reported in the following Bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=205015
[ 1663.694828] e1000e 0000:00:19.0 eth0: Failed to disable ULP
[ 1664.731040] asix 2-3:1.0 eth1: link up, 100Mbps, full-duplex, lpa 0xC1E1
[ 1665.093513] e1000e 0000:00:19.0 eth0: Hardware Error
[ 1665.596760] e1000e 0000:00:19.0: pci_pm_resume+0x0/0x80 returned 0 after 2975399 usecs
and then the system never recovers from it, and all the following suspend failed due to this
[22909.393854] PM: pci_pm_suspend(): e1000e_pm_suspend+0x0/0x760 [e1000e] returns -2
[22909.393858] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -2
[22909.393861] PM: Device 0000:00:1f.6 failed to suspend async: error -2
This can be avoided by changing the return values of __e1000_shutdown and
e1000e_pm_suspend functions so that they always return 0 (success). This
is consistent with what other drivers do.
If the e1000e driver encounters a hardware error during suspend, potential
side effects include slightly higher power draw or non-working wake on
LAN. This is preferred to a system-level suspend failure, and a warning
message is written to the system log, so that the user can be aware that
the LAN controller experienced a problem during suspend.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=205015
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix three issues in the amd-pstate cpufreq driver.
Specifics:
- Remove checks for highest performance match on preferred cores when
updating preferred core ranking in amd-pstate (Mario Limonciello)
- Make amd-pstate call topology_logical_package_id() instead of
logical_die_id() to get a socked ID for a CPU (Gautham Shenoy)
- Fix uninitialized variable in amd_pstate_cpu_boost_update() (Dan
Carpenter)"
* tag 'pm-6.11-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate-ut: Don't check for highest perf matching on prefcore
cpufreq/amd-pstate: Use topology_logical_package_id() instead of logical_die_id()
cpufreq: amd-pstate: Fix uninitialized variable in amd_pstate_cpu_boost_update()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
- A bunch of dw driver changes to fix the src/dst addr width config
- Omap driver fix for sglen initialization
- stm32-dma3 driver lli_size init fix
- dw edma driver fixes for watermark interrupts and unmasking STOP and
ABORT interrupts
* tag 'dmaengine-fix-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dmaengine: dw-edma: Do not enable watermark interrupts for HDMA
dmaengine: dw-edma: Fix unmasking STOP and ABORT interrupts for HDMA
dmaengine: stm32-dma3: Set lli_size after allocation
dmaengine: ti: omap-dma: Initialize sglen after allocation
dmaengine: dw: Unify ret-val local variables naming
dmaengine: dw: Simplify max-burst calculation procedure
dmaengine: dw: Define encode_maxburst() above prepare_ctllo() callbacks
dmaengine: dw: Simplify prepare CTL_LO methods
dmaengine: dw: Add memory bus width verification
dmaengine: dw: Add peripheral bus width verification
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy fixes from Vinod Koul:
- Qualcomm QMP X1E80100 PCIe Gen4 PHY initialisation fix
- Freescale imx8mq tuning parameter name fix
- Samsung exynos5 fir for error code in probe()
- Xilinx Zynqmp SGMII linkup failure fix
* tag 'phy-fixes-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy:
phy: xilinx: phy-zynqmp: Fix SGMII linkup failure on resume
phy: exynos5-usbdrd: fix error code in probe()
phy: fsl-imx8mq-usb: fix tuning parameter name
phy: qcom: qmp-pcie: Fix X1E80100 PCIe Gen4 PHY initialisation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire
Pull soundwire fix from Vinod Koul:
- Single fix for non-continous port map programming
* tag 'soundwire-6.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire:
soundwire: stream: fix programming slave ports for non-continous port maps
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu fixes from Joerg Roedel:
- Fix a device-stall problem in bad io-page-fault setups (faults
received from devices with no supporting domain attached).
- Context flush fix for Intel VT-d.
- Do not allow non-read+non-write mapping through iommufd as most
implementations can not handle that.
- Fix a possible infinite-loop issue in map_pages() path.
- Add Jean-Philippe as reviewer for SMMUv3 SVA support
* tag 'iommu-fixes-v6.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux:
MAINTAINERS: Add Jean-Philippe as SMMUv3 SVA reviewer
iommu: Do not return 0 from map_pages if it doesn't do anything
iommufd: Do not allow creating areas without READ or WRITE
iommu/vt-d: Fix incorrect domain ID in context flush helper
iommu: Handle iommu faults for a bad iopf setup
|
|
Use ERR_CAST() as it is designed for casting an error pointer to
another type.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Link: https://patch.msgid.link/20240829072538.33195-1-shenlichuan@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As opposed to open-code, using the ERR_CAST macro clearly indicates that
this is a pointer to an error value and a type conversion was performed.
Signed-off-by: Shen Lichuan <shenlichuan@vivo.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Martin Habets <habetsm.xilinx@gmail.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20240829021253.3066-1-shenlichuan@vivo.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Hook up pKVM's MMIO_GUARD hypercall so that ioremap() and friends will
register the target physical address as MMIO with the hypervisor,
allowing guest exits to that page to be emulated by the host with full
syndrome information.
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240830130150.8568-7-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
If we detect the presence of pKVM's SHARE and UNSHARE hypercalls, then
register a backend implementation of the mem_encrypt API so that things
like DMA buffers can be shared appropriately with the host.
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240830130150.8568-5-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Implement a pKVM protected guest driver to probe the presence of pKVM
and determine the memory protection granule using the HYP_MEMINFO
hypercall.
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240830130150.8568-3-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
arm64 will soon require its own callback to initialise services
that are only available on this architecture. Introduce a hook
that can be overloaded by the architecture.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240830130150.8568-2-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
MULTI GBT AN Control Register is IEEE Standard Register 7.32 (not a mask).
The right place should be in igc_reg.h file. In accordance with the
registers naming convention added IGC_' prefix.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
According to the IEEE standard report the EEE ability (registers 7.60 and
7.62) and the EEE Link Partner ability (registers 7.61 and 7.63). Use the
kernel's 'ethtool_keee' structure and report EEE link modes.
Example:
ethtool --show-eee <device>
Before:
Advertised EEE link modes: Not reported
Link partner advertised EEE link modes: Not reported
After:
Advertised EEE link modes: 100baseT/Full
1000baseT/Full
2500baseT/Full
Link partner advertised EEE link modes: 100baseT/Full
1000baseT/Full
2500baseT/Full
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When running the igc with XDP/ZC in busy polling mode with deferral of hard
interrupts, interrupts still happen from time to time. That is caused by
the igc task watchdog which triggers Rx interrupts periodically.
That mechanism has been introduced to overcome skb/memory allocation
failures [1]. So the Rx clean functions stop processing the Rx ring in case
of such failure. The task watchdog triggers Rx interrupts periodically in
the hope that memory became available in the mean time.
The current behavior is undesirable for real time applications, because the
driver induced Rx interrupts trigger also the softirq processing. However,
all real time packets should be processed by the application which uses the
busy polling method.
Therefore, only trigger the Rx interrupts in case of real allocation
failures. Introduce a new flag for signaling that condition.
[1] - https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=3be507547e6177e5c808544bd6a2efa2c7f1d436
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add support for offloading MQPRIO. The hardware has four priorities as well
as four queues. Each queue must be a assigned with a unique priority.
However, the priorities are only considered in TSN Tx mode. There are two
TSN Tx modes. In case of MQPRIO the Qbv capability is not required.
Therefore, use the legacy TSN Tx mode, which performs strict priority
arbitration.
Example for mqprio with hardware offload:
|tc qdisc replace dev ${INTERFACE} handle 100 parent root mqprio num_tc 4 \
| map 0 0 0 0 0 1 2 3 0 0 0 0 0 0 0 0 \
| queues 1@0 1@1 1@2 1@3 \
| hw 1
The mqprio Qdisc also allows to configure the `preemptible_tcs'. However,
frame preemption is not supported yet.
Tested on Intel i225 and implemented by following data sheet section 7.5.2,
Transmit Scheduling.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial device id for 6.11-rc6
Here's a new modem device id.
This one has been in linux-next with no reported issues.
* tag 'usb-serial-6.11-rc6' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: option: add MeiG Smart SRM825L
|
|
There is only one called of alloc_page_buffers and it doesn't require
__GFP_NOFAIL so drop this allocation mode.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Link: https://lore.kernel.org/r/20240829130640.1397970-1-mhocko@kernel.org
Acked-by: Song Liu <song@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
We use komeda_crtc_normalize_zpos to normalize zpos of affected planes
to their blending zorder in CU. If there's only one slave plane in
affected planes and its layer_split property is enabled, order++ for
its split layer, so that when calculating the normalized_zpos
of master planes, the split layer of the slave plane is included, but
the max_slave_zorder does not include the split layer and keep zero
because there's only one slave plane in affacted planes, although we
actually use two slave layers in this commit.
In most cases, this bug does not result in a commit failure, but assume
the following situation:
slave_layer 0: zpos = 0, layer split enabled, normalized_zpos =
0;(use slave_layer 2 as its split layer)
master_layer 0: zpos = 2, layer_split enabled, normalized_zpos =
2;(use master_layer 2 as its split layer)
master_layer 1: zpos = 4, normalized_zpos = 4;
master_layer 3: zpos = 5, normalized_zpos = 5;
kcrtc_st->max_slave_zorder = 0;
When we use master_layer 3 as a input of CU in function
komeda_compiz_set_input and check it with function
komeda_component_check_input, the parameter idx is equal to
normailzed_zpos minus max_slave_zorder, the value of idx is 5
and is euqal to CU's max_active_inputs, so that
komeda_component_check_input returns a -EINVAL value.
To fix the bug described above, when calculating the max_slave_zorder
with the layer_split enabled, count the split layer in this calculation
directly.
Signed-off-by: hongchi.peng <hongchi.peng@siengine.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240826024517.3739-1-hongchi.peng@siengine.com
|
|
intel_spi_populate_chip() use devm_kasprintf() to set pdata->name.
This can return a NULL pointer on failure but this returned value
is not checked.
Fixes: e58db3bcd93b ("spi: intel: Add default partition and name to the second chip")
Signed-off-by: Charles Han <hanchunchao@inspur.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://patch.msgid.link/20240830074106.8744-1-hanchunchao@inspur.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently users can get the Root Ports supported by the PCIe PMU by
"bus" sysfs attributes which indicates the PCIe bus number where
Root Ports are located. This maybe insufficient since Root Ports
supported by different PCIe PMUs may be located on the same PCIe bus.
So export the BDF range the Root Ports additionally.
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240829090332.28756-4-yangyicong@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
We make the initial value of event ctrl register as HISI_PCIE_INIT_SET
and modify according to the user options. This will make TLP headers
bandwidth only counting never take effect since HISI_PCIE_INIT_SET
configures to count the TLP payloads bandwidth. Fix this by making
the initial value of event ctrl register as 0.
Fixes: 17d573984d4d ("drivers/perf: hisi: Add TLP filter support")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240829090332.28756-3-yangyicong@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Currently we set the period and record it as the initial value of the
counter without checking it's set to the hardware successfully or not.
However the counter maybe unwritable if the target event is unsupported
by the device. In such case we will pass user a wrong count:
[start counts when setting the period]
hwc->prev_count = 0x8000000000000000
device.counter_value = 0 // the counter is not set as the period
[when user reads the counter]
event->count = device.counter_value - hwc->prev_count
= 0x8000000000000000 // wrong. should be 0.
Fix this by record the hardware counter counts correctly when setting
the period.
Fixes: 8404b0fbc7fb ("drivers/perf: hisi: Add driver for HiSilicon PCIe PMU")
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20240829090332.28756-2-yangyicong@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Use perf_allow_kernel() for 'pa_enable' (physical addresses),
'pct_enable' (physical timestamps) and context IDs. This means that
perf_event_paranoid is now taken into account and LSM hooks can be used,
which is more consistent with other perf_event_open calls. For example
PERF_SAMPLE_PHYS_ADDR uses perf_allow_kernel() rather than just
perfmon_capable().
This also indirectly fixes the following error message which is
misleading because perf_event_paranoid is not taken into account by
perfmon_capable():
$ perf record -e arm_spe/pa_enable/
Error:
Access to performance monitoring and observability operations is
limited. Consider adjusting /proc/sys/kernel/perf_event_paranoid
setting ...
Suggested-by: Al Grant <al.grant@arm.com>
Signed-off-by: James Clark <james.clark@linaro.org>
Link: https://lore.kernel.org/r/20240827145113.1224604-1-james.clark@linaro.org
Link: https://lore.kernel.org/all/20240807120039.GD37996@noisy.programming.kicks-ass.net/
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The req_lock is currently implemented as a rw_lock, but there are no
instances where read_lock() is called. This means that the lock is
effectively only used by writers, making it functionally equivalent to
a simple spinlock.
As stated in Documentation/locking/spinlocks.rst:
"Reader-writer locks require more atomic memory operations than simple
spinlocks. Unless the reader critical section is long, you are better
off just using spinlocks."
Since the rw_lock in this case incurs additional atomic memory
operations without any benefit from reader-writer locking, it is more
efficient to replace it with a spinlock. This patch implements that
replacement to optimize the driver's performance.
Signed-off-by: Kuan-Wei Chiu <visitorckw@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Simplify the code by replacing devm_clk_get() and clk_prepare_enable()
with devm_clk_get_enabled(), which also avoids the call to
clk_disable_unprepare().
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Simplify the code by replacing devm_clk_get() and clk_prepare() with
devm_clk_get_prepared(), which also avoids the call to clk_unprepare().
Signed-off-by: Chunhai Guo <guochunhai@vivo.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
It's unlikely that devm_pm_runtime_enable ever fails. Still, it makes
sense to read the return value and handle errors.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The driver uses the rst variable only for an initial reset when the chip
is probed. There's no need to store rst in the driver's private data, we
can make it a local variable in the probe function.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The devm_clk_get_enabled() helpers:
- call devm_clk_get()
- call clk_prepare_enable() and register what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code and avoids the calls to clk_disable_unprepare().
Signed-off-by: Huan Yang <link@vivo.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
