| Age | Commit message (Collapse) | Author |
|---|
|
6131 is the only driver to set the tag protocol to DSA_TAG_PROTO_DSA.
Since it works fine with DSA_TAG_PROTO_EDSA, change its value, like all
other mv88e6xxx drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide a shared mv88e6xxx_setup function to the drivers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
6131 is the only driver which setups the priority of IGMP/MLD snoop
frames and ARP frames to the highest setting. Drop such change until we
figure out a common configuration for all switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All switch models setup the GLOBAL_CONTROL_2 register with slightly
differences.
Since the cascade mode is valid even in a single chip setup, factorize
such configuration.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All switch drivers configure the GLOBAL_MONITOR_CONTROL register with
slightly changes.
Assume the setup of the upstream port, and configure it as the port to
which ingress and egress and ARP monitor frames are to be sent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6131 switch models have a Core Tag Type register. Their setup code
is setting it to 0x8100, which is the reset default.
Drop this specific part which is correctly configured on reset anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All switch models configure the GLOBAL_CONTROL register with slightly
differences.
Discarding packets with excessive collisions
(GLOBAL_CONTROL_DISCARD_EXCESS) is specific to 6352 and similar
switches, and setting a maximum frame size
(GLOBAL_CONTROL_MAX_FRAME_1632) is specific to 6185 and similar
switches.
As we are centralizing the chips setup, skip these settings and don't
discard any frames yet, until we found out that such discarding by the
hardware is necessary.
Assume a common setup to enable the PHY Polling Unit if present, don't
discard any packets, and mask all interrupt sources.
Tested on 88E6352 and 88E6185.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Every driver is calling mv88e6xxx_setup_global after
mv88e6xxx_setup_common. Call the former in the latter.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_PPU_ACTIVE flag to describe how to reset the
switch, and merge the reset call to the common setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_ATU flag to identify switch models with an Address
Translation Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_VTU flag to indentify switch models with a VLAN
Table Unit.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MV88E6XXX_FLAG_PORTSTATE and MV88E6XXX_FLAG_VLANTABLE flags to
identify switch models with required 802.1D operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only 6131 was not supporting the port registers access yet. Assume such
support and use the unlock access routines in the meantime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_EEE flag to describe switch models featuring Energy
Efficient Ethernet. Use it to conditionally support such access in the
common code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switch models have a dedicated register for Switch MAC/WoF/WoL.
This register, when present, is used to indirectly set the switch MAC
address, instead of a direct write to 3 global registers.
Identify this feature and share a common mv88e6xxx_set_addr function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add MV88E6XXX_FLAG_TEMP and MV88E6XXX_FLAG_TEMP_LIMIT flags to describe
switch models featuring a temperature access. Use them to centralize the
access to the temperature feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_EEPROM flag to describe switch models featuring an
EEPROM and distribute the EEPROM access routines to all models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switch has dedicated SMI PHY Command and Data registers, used to
indirectly access the PHYs, instead of direct access.
Identify these switch models and make mv88e6xxx_phy_{read,write} generic
enough to support every models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a MV88E6XXX_FLAG_PPU flag to describe switch models with a PHY
Polling Unit. This allows to merge PPU specific PHY access code in the
share code.
Make the mv88e6xxx_ppu_disable and mv88e6xxx_phy_{read,write}_ppu
functions use unlocked register accesses in order to call them in
mv88e6xxx_phy_{read,write} in a locked context.
Since the PPU code is shared, also remove NET_DSA_MV88E6XXX_NEED_PPU.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flags bitmap to the info structure in order to identify features
supported or not by the different switch models.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit cd6cfd7311a385144a2f9c74f692ae2df3ae033f
"ath9k: do not set half/quarter channel flags in AR_PHY_MODE" the
condition "rfMode & (AR_PHY_MODE_QUARTER | AR_PHY_MODE_HALF)" would
never evaluate to true.
Fix this by using the available IS_CHAN_HALF_RATE and IS_CHAN_QUARTER_RATE
marcros instead.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
USB_PID_DIBCOM_STK8096GP also comes with USB_VID_DIBCOM vendor ID.
Signed-off-by: Alejandro Torrado <aletorrado@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
There's no need to keep the same for loop twice in the code.
Move the txpower cap before the loop to reduce code complexity.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Since ATH9K_TX99 depends on ATH9K_DEBUGFS anyway move it there
such that "make menuconfig" will indent TX99 support below ath9k
debugging.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The same functionality as ar9003_hw_tx_power_regwrite is hardcoded in
ar9003_hw_tx99_set_txpower. Just reuse the existing ar9003_hw_tx_power_regwrite
for TX99 setup too.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The tvp5150_write() function can fail so don't return 0 unconditionally
in tvp5150_s_register() but propagate what's returned by tvp5150_write().
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The tvp5150_write() function calls i2c_smbus_write_byte_data() that
can fail but does not propagate the error to the caller. Instead it
just prints a debug, so callers can't know if the operation failed.
So change the function to return the error code to the caller so it
knows that the write failed and also print an error instead of just
printing a debug information.
While being there remove the inline keyword from tvp5150_write() to
make it consistent with tvp5150_read() and also because it's called
in a lot of places, so making inline is in fact counter productive
since it makes the kernel image size to be much bigger (~16 KiB).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
'ppc/pamu', 'core' and 'x86/amd' into next
|
|
Now that we can accurately reflect the context format we choose for each
domain, do that instead of imposing the global lowest-common-denominator
restriction and potentially ending up with nothing. We currently have a
strict 1:1 correspondence between domains and context banks, so we don't
need to entertain the possibility of multiple formats _within_ a domain.
Signed-off-by: Will Deacon <will.deacon@arm.com>
[rm: split from original patch, added SMMUv3]
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Hauppauge WinTV-dualHD is a USB 2.0 dual DVB-T/T2/C tuner with
following components:
USB bridge: Empia EM28274 (chip id is the same as EM28174)
Demodulator: 2x Silicon Labs Si2168-B40
Tuner: 2x Silicon Labs Si2157-A30
This patch adds support only for the first tuner.
The demodulator needs firmware, available for example here:
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/4.0.11/
The demodulators sit on the same I2C bus and their addresses
are 0x64 and 0x67. The tuners are behind the demodulators and
their addresses are 0x60 and 0x63.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Byte 69 bits 0:1 in the IDENTIFY DEVICE data indicate a
host-aware ZAC device.
Host-managed ZAC devices have their own individual signature,
and to not set the bits in the IDENTIFY DEVICE data.
And whenever we detect a ZAC-compatible device we should
be displaying the zoned block characteristics VPD page.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Device-managed ZAC devices just set the zoned capabilities field
in INQUIRY byte 69 (cf ACS-4). This corresponds to the 'zoned'
field in the block device characteristics VPD page.
As this is only defined in SPC-5/SBC-4 we also need to update
the supported SCSI version descriptor.
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Add NCQ encapsulation for ZAC MANAGEMENT OUT and evaluate
NCQ Non-Data log pages to figure out if NCQ encapsulation
is supported.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ZAC drives implement a 'ZAC Management Out' command template,
which maps onto the ZBC OUT command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ZAC drives implement a 'ZAC Management In' command template,
which maps onto the ZBC IN command.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
If a device is disabled after error recovery it doesn't make
any sense to generate an ATA sense, but we should rather
return a generic sense code indicating the device is gone.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Some commands like FPDMA RECEIVE or NCQ NON DATA can encapsulate
other commands to NCQ transport. So decode the subcmds, too.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
When reading the NCQ Send/Recv log it might actually not
supported, thereby causing irritating messages
'READ LOG DMA EXT failed'.
Instead we should be reading the log directory first to
figure out if the log is actually supported before trying
to access it.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Move NCQ SEND/RECEIVE checks into a separate function.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Define the NCQ NON DATA command and update libsas to handle it
correctly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Update libsas and dependent drivers to handle FPDMA
SEND/RECEIVE correctly.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Do not call ata_request_sense() if the sense code is already
present.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi into for-4.7-zac
Pulling in the dependencies for further ZAC changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
NULL pointer derefence happens when booting with DTB because the
platform data for haptic device is not set in supplied data from parent
MFD device.
The MFD device creates only platform data (from Device Tree) for itself,
not for haptic child.
Unable to handle kernel NULL pointer dereference at virtual address 0000009c
pgd = c0004000
[0000009c] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
(max8997_haptic_probe) from [<c03f9cec>] (platform_drv_probe+0x4c/0xb0)
(platform_drv_probe) from [<c03f8440>] (driver_probe_device+0x214/0x2c0)
(driver_probe_device) from [<c03f8598>] (__driver_attach+0xac/0xb0)
(__driver_attach) from [<c03f67ac>] (bus_for_each_dev+0x68/0x9c)
(bus_for_each_dev) from [<c03f7a38>] (bus_add_driver+0x1a0/0x218)
(bus_add_driver) from [<c03f8db0>] (driver_register+0x78/0xf8)
(driver_register) from [<c0101774>] (do_one_initcall+0x90/0x1d8)
(do_one_initcall) from [<c0a00dbc>] (kernel_init_freeable+0x15c/0x1fc)
(kernel_init_freeable) from [<c06bb5b4>] (kernel_init+0x8/0x114)
(kernel_init) from [<c0107938>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 104594b01ce7 ("Input: add driver support for MAX8997-haptic")
[k.kozlowski: Write commit message, add CC-stable]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
As pointed out by Richard, the changes to the comment got missed off
the absolute mode patch somehow.
Signed-off-by: Chris Diamand <chris@diamand.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Replace custom approach by %*ph specifier to dump small buffers in hex format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
We don't need to run the full path of recv_daemon
if process_recvd_msg doesn't return 0.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
The in-memory bitmap is not ready when node joins cluster,
so it doesn't make sense to make gather_all_resync_info()
called so earlier, we need to call it after the node's
bitmap is setup. Also, recv_thread could be wake up after
node joins cluster, but it could cause problem if node
receives RESYNCING message without persionality since
mddev->pers->quiesce is called in process_suspend_info.
This commit introduces a new cluster interface load_bitmaps
to fix above problems, load_bitmaps is called in bitmap_load
where bitmap and persionality are ready, and load_bitmaps
does the following tasks:
1. call gather_all_resync_info to load all the node's
bitmap info.
2. set MD_CLUSTER_ALREADY_IN_CLUSTER bit to recv_thread
could be wake up, and wake up recv_thread if there is
pending recv event.
Then ack_bast only wakes up recv_thread after IN_CLUSTER
bit is ready otherwise MD_CLUSTER_PENDING_RESYNC_EVENT is
set.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
Some code waits for a metadata update by:
1. flagging that it is needed (MD_CHANGE_DEVS or MD_CHANGE_CLEAN)
2. setting MD_CHANGE_PENDING and waking the management thread
3. waiting for MD_CHANGE_PENDING to be cleared
If the first two are done without locking, the code in md_update_sb()
which checks if it needs to repeat might test if an update is needed
before step 1, then clear MD_CHANGE_PENDING after step 2, resulting
in the wait returning early.
So make sure all places that set MD_CHANGE_PENDING are atomicial, and
bit_clear_unless (suggested by Neil) is introduced for the purpose.
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: <linux-kernel@vger.kernel.org>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
In case md runs underneath the dm-raid target, the mddev does not have
a request queue or gendisk, thus avoid accesses.
This patch adds a missing conditional to the raid5 personality.
Signed-of-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Shaohua Li <shli@fb.com>
|
