summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-02-17drm/nouveau/kms/gv100-: Re-set LUT after clearing for modesetsLyude Paul
While certain modeset operations on gv100+ need us to temporarily disable the LUT, we make the mistake of sometimes neglecting to reprogram the LUT after such modesets. In particular, moving a head from one encoder to another seems to trigger this quite often. GV100+ is very picky about having a LUT in most scenarios, so this causes the display engine to hang with the following error code: disp: chid 1 stat 00005080 reason 5 [INVALID_STATE] mthd 0200 data 00000001 code 0000002d) So, fix this by always re-programming the LUT if we're clearing it in a state where the wndw is still visible, and has a XLUT handle programmed. Signed-off-by: Lyude Paul <lyude@redhat.com> Fixes: facaed62b4cb ("drm/nouveau/kms/gv100: initial support") Cc: <stable@vger.kernel.org> # v4.18+ Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2020-02-17drm/nouveau/gr/tu11x: initial supportBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2020-02-17drm/nouveau/acr/tu11x: initial supportBen Skeggs
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
2020-02-16net: ethernet: dm9000: Handle -EPROBE_DEFER in dm9000_parse_dt()Paul Cercueil
The call to of_get_mac_address() can return -EPROBE_DEFER, for instance when the MAC address is read from a NVMEM driver that did not probe yet. Cc: H. Nikolaus Schaller <hns@goldelico.com> Cc: Mathieu Malaterre <malat@debian.org> Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Fix 16-bit IO operationMarek Vasut
The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that BE[3:0] signals are active high. This contradicts the measurements of the behavior of the actual chip, where these signals behave as active low. For example, to read the CIDER register, the bus must expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Fix 16-bit data accessMarek Vasut
The packet data written to and read from Micrel KSZ8851-16MLLI must be byte-swapped in 16-bit mode, add this byte-swapping. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Remove 8-bit bus accessorsMarek Vasut
This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown, however the speculation is that this was some sort of attempt to support the 8-bit bus mode. As per the KS8851-16MLL documentation, all two registers accessed via the 8-bit accessors are internally 16-bit registers, so reading them using 16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read outright, as it is already a concatenation of two 8-bit reads of that register. The KS_RXQCR accesses are 8-bit only, however writing the top 8 bits of the register is OK as well, since the driver caches the entire 16-bit register value anyway. Finally, the driver is not used by any hardware in the kernel right now. The only hardware available to me is one with 16-bit bus, so I have no way to test the 8-bit bus mode, however it is unlikely this ever really worked anyway. If the 8-bit bus mode is ever required, it can be easily added by adjusting the 16-bit accessors to do 2 consecutive accesses, which is how this should have been done from the beginning. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16bonding: fix lockdep warning in bond_get_stats()Taehee Yoo
In the "struct bonding", there is stats_lock. This lock protects "bond_stats" in the "struct bonding". bond_stats is updated in the bond_get_stats() and this function would be executed concurrently. So, the lock is needed. Bonding interfaces would be nested. So, either stats_lock should use dynamic lockdep class key or stats_lock should be used by spin_lock_nested(). In the current code, stats_lock is using a dynamic lockdep class key. But there is no updating stats_lock_key routine So, lockdep warning will occur. Test commands: ip link add bond0 type bond ip link add bond1 type bond ip link set bond0 master bond1 ip link set bond0 nomaster ip link set bond1 master bond0 Splat looks like: [ 38.420603][ T957] 5.5.0+ #394 Not tainted [ 38.421074][ T957] ------------------------------------------------------ [ 38.421837][ T957] ip/957 is trying to acquire lock: [ 38.422399][ T957] ffff888063262cd8 (&bond->stats_lock_key#2){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.423528][ T957] [ 38.423528][ T957] but task is already holding lock: [ 38.424526][ T957] ffff888065fd2cd8 (&bond->stats_lock_key){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.426075][ T957] [ 38.426075][ T957] which lock already depends on the new lock. [ 38.426075][ T957] [ 38.428536][ T957] [ 38.428536][ T957] the existing dependency chain (in reverse order) is: [ 38.429475][ T957] [ 38.429475][ T957] -> #1 (&bond->stats_lock_key){+.+.}: [ 38.430273][ T957] _raw_spin_lock+0x30/0x70 [ 38.430812][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ 38.431451][ T957] dev_get_stats+0x1ec/0x270 [ 38.432088][ T957] bond_get_stats+0x1a5/0x4d0 [bonding] [ 38.432767][ T957] dev_get_stats+0x1ec/0x270 [ 38.433322][ T957] rtnl_fill_stats+0x44/0xbe0 [ 38.433866][ T957] rtnl_fill_ifinfo+0xeb2/0x3720 [ 38.434474][ T957] rtmsg_ifinfo_build_skb+0xca/0x170 [ 38.435081][ T957] rtmsg_ifinfo_event.part.33+0x1b/0xb0 [ 38.436848][ T957] rtnetlink_event+0xcd/0x120 [ 38.437455][ T957] notifier_call_chain+0x90/0x160 [ 38.438067][ T957] netdev_change_features+0x74/0xa0 [ 38.438708][ T957] bond_compute_features.isra.45+0x4e6/0x6f0 [bonding] [ 38.439522][ T957] bond_enslave+0x3639/0x47b0 [bonding] [ 38.440225][ T957] do_setlink+0xaab/0x2ef0 [ 38.440786][ T957] __rtnl_newlink+0x9c5/0x1270 [ 38.441463][ T957] rtnl_newlink+0x65/0x90 [ 38.442075][ T957] rtnetlink_rcv_msg+0x4a8/0x890 [ 38.442774][ T957] netlink_rcv_skb+0x121/0x350 [ 38.443451][ T957] netlink_unicast+0x42e/0x610 [ 38.444282][ T957] netlink_sendmsg+0x65a/0xb90 [ 38.444992][ T957] ____sys_sendmsg+0x5ce/0x7a0 [ 38.445679][ T957] ___sys_sendmsg+0x10f/0x1b0 [ 38.446365][ T957] __sys_sendmsg+0xc6/0x150 [ 38.447007][ T957] do_syscall_64+0x99/0x4f0 [ 38.447668][ T957] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 38.448538][ T957] [ 38.448538][ T957] -> #0 (&bond->stats_lock_key#2){+.+.}: [ 38.449554][ T957] __lock_acquire+0x2d8d/0x3de0 [ 38.450148][ T957] lock_acquire+0x164/0x3b0 [ 38.450711][ T957] _raw_spin_lock+0x30/0x70 [ 38.451292][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ 38.451950][ T957] dev_get_stats+0x1ec/0x270 [ 38.452425][ T957] bond_get_stats+0x1a5/0x4d0 [bonding] [ 38.453362][ T957] dev_get_stats+0x1ec/0x270 [ 38.453825][ T957] rtnl_fill_stats+0x44/0xbe0 [ 38.454390][ T957] rtnl_fill_ifinfo+0xeb2/0x3720 [ 38.456257][ T957] rtmsg_ifinfo_build_skb+0xca/0x170 [ 38.456998][ T957] rtmsg_ifinfo_event.part.33+0x1b/0xb0 [ 38.459351][ T957] rtnetlink_event+0xcd/0x120 [ 38.460086][ T957] notifier_call_chain+0x90/0x160 [ 38.460829][ T957] netdev_change_features+0x74/0xa0 [ 38.461752][ T957] bond_compute_features.isra.45+0x4e6/0x6f0 [bonding] [ 38.462705][ T957] bond_enslave+0x3639/0x47b0 [bonding] [ 38.463476][ T957] do_setlink+0xaab/0x2ef0 [ 38.464141][ T957] __rtnl_newlink+0x9c5/0x1270 [ 38.464897][ T957] rtnl_newlink+0x65/0x90 [ 38.465522][ T957] rtnetlink_rcv_msg+0x4a8/0x890 [ 38.466215][ T957] netlink_rcv_skb+0x121/0x350 [ 38.466895][ T957] netlink_unicast+0x42e/0x610 [ 38.467583][ T957] netlink_sendmsg+0x65a/0xb90 [ 38.468285][ T957] ____sys_sendmsg+0x5ce/0x7a0 [ 38.469202][ T957] ___sys_sendmsg+0x10f/0x1b0 [ 38.469884][ T957] __sys_sendmsg+0xc6/0x150 [ 38.470587][ T957] do_syscall_64+0x99/0x4f0 [ 38.471245][ T957] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 38.472093][ T957] [ 38.472093][ T957] other info that might help us debug this: [ 38.472093][ T957] [ 38.473438][ T957] Possible unsafe locking scenario: [ 38.473438][ T957] [ 38.474898][ T957] CPU0 CPU1 [ 38.476234][ T957] ---- ---- [ 38.480171][ T957] lock(&bond->stats_lock_key); [ 38.480808][ T957] lock(&bond->stats_lock_key#2); [ 38.481791][ T957] lock(&bond->stats_lock_key); [ 38.482754][ T957] lock(&bond->stats_lock_key#2); [ 38.483416][ T957] [ 38.483416][ T957] *** DEADLOCK *** [ 38.483416][ T957] [ 38.484505][ T957] 3 locks held by ip/957: [ 38.485048][ T957] #0: ffffffffbccf6230 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x457/0x890 [ 38.486198][ T957] #1: ffff888065fd2cd8 (&bond->stats_lock_key){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.487625][ T957] #2: ffffffffbc9254c0 (rcu_read_lock){....}, at: bond_get_stats+0x5/0x4d0 [bonding] [ 38.488897][ T957] [ 38.488897][ T957] stack backtrace: [ 38.489646][ T957] CPU: 1 PID: 957 Comm: ip Not tainted 5.5.0+ #394 [ 38.490497][ T957] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 38.492810][ T957] Call Trace: [ 38.493219][ T957] dump_stack+0x96/0xdb [ 38.493709][ T957] check_noncircular+0x371/0x450 [ 38.494344][ T957] ? lookup_address+0x60/0x60 [ 38.494923][ T957] ? print_circular_bug.isra.35+0x310/0x310 [ 38.495699][ T957] ? hlock_class+0x130/0x130 [ 38.496334][ T957] ? __lock_acquire+0x2d8d/0x3de0 [ 38.496979][ T957] __lock_acquire+0x2d8d/0x3de0 [ 38.497607][ T957] ? register_lock_class+0x14d0/0x14d0 [ 38.498333][ T957] ? check_chain_key+0x236/0x5d0 [ 38.499003][ T957] lock_acquire+0x164/0x3b0 [ 38.499800][ T957] ? bond_get_stats+0x90/0x4d0 [bonding] [ 38.500706][ T957] _raw_spin_lock+0x30/0x70 [ 38.501435][ T957] ? bond_get_stats+0x90/0x4d0 [bonding] [ 38.502311][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ ... ] But, there is another problem. The dynamic lockdep class key is protected by RTNL, but bond_get_stats() would be called outside of RTNL. So, it would use an invalid dynamic lockdep class key. In order to fix this issue, stats_lock uses spin_lock_nested() instead of a dynamic lockdep key. The bond_get_stats() calls bond_get_lowest_level_rcu() to get the correct nest level value, which will be used by spin_lock_nested(). The "dev->lower_level" indicates lower nest level value, but this value is invalid outside of RTNL. So, bond_get_lowest_level_rcu() returns valid lower nest level value in the RCU critical section. bond_get_lowest_level_rcu() will be work only when LOCKDEP is enabled. Fixes: 089bca2caed0 ("bonding: use dynamic lockdep key instead of subclass") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16bonding: add missing netdev_update_lockdep_key()Taehee Yoo
After bond_release(), netdev_update_lockdep_key() should be called. But both ioctl path and attribute path don't call netdev_update_lockdep_key(). This patch adds missing netdev_update_lockdep_key(). Test commands: ip link add bond0 type bond ip link add bond1 type bond ifenslave bond0 bond1 ifenslave -d bond0 bond1 ifenslave bond1 bond0 Splat looks like: [ 29.501182][ T1046] WARNING: possible circular locking dependency detected [ 29.501945][ T1039] hardirqs last disabled at (1962): [<ffffffffac6c807f>] handle_mm_fault+0x13f/0x700 [ 29.503442][ T1046] 5.5.0+ #322 Not tainted [ 29.503447][ T1046] ------------------------------------------------------ [ 29.504277][ T1039] softirqs last enabled at (1180): [<ffffffffade00678>] __do_softirq+0x678/0x981 [ 29.505443][ T1046] ifenslave/1046 is trying to acquire lock: [ 29.505886][ T1039] softirqs last disabled at (1169): [<ffffffffac19c18a>] irq_exit+0x17a/0x1a0 [ 29.509997][ T1046] ffff88805d5da280 (&dev->addr_list_lock_key#3){+...}, at: dev_mc_sync_multiple+0x95/0x120 [ 29.511243][ T1046] [ 29.511243][ T1046] but task is already holding lock: [ 29.512192][ T1046] ffff8880460f2280 (&dev->addr_list_lock_key#4){+...}, at: bond_enslave+0x4482/0x47b0 [bonding] [ 29.514124][ T1046] [ 29.514124][ T1046] which lock already depends on the new lock. [ 29.514124][ T1046] [ 29.517297][ T1046] [ 29.517297][ T1046] the existing dependency chain (in reverse order) is: [ 29.518231][ T1046] [ 29.518231][ T1046] -> #1 (&dev->addr_list_lock_key#4){+...}: [ 29.519076][ T1046] _raw_spin_lock+0x30/0x70 [ 29.519588][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.520208][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.520862][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ 29.521640][ T1046] __bond_opt_set+0x1ff/0xbb0 [bonding] [ 29.522438][ T1046] __bond_opt_set_notify+0x2b/0xf0 [bonding] [ 29.523251][ T1046] bond_opt_tryset_rtnl+0x92/0xf0 [bonding] [ 29.524082][ T1046] bonding_sysfs_store_option+0x8a/0xf0 [bonding] [ 29.524959][ T1046] kernfs_fop_write+0x276/0x410 [ 29.525620][ T1046] vfs_write+0x197/0x4a0 [ 29.526218][ T1046] ksys_write+0x141/0x1d0 [ 29.526818][ T1046] do_syscall_64+0x99/0x4f0 [ 29.527430][ T1046] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 29.528265][ T1046] [ 29.528265][ T1046] -> #0 (&dev->addr_list_lock_key#3){+...}: [ 29.529272][ T1046] __lock_acquire+0x2d8d/0x3de0 [ 29.529935][ T1046] lock_acquire+0x164/0x3b0 [ 29.530638][ T1046] _raw_spin_lock+0x30/0x70 [ 29.531187][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.531790][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.532451][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ 29.533163][ T1046] __bond_opt_set+0x1ff/0xbb0 [bonding] [ 29.533789][ T1046] __bond_opt_set_notify+0x2b/0xf0 [bonding] [ 29.534595][ T1046] bond_opt_tryset_rtnl+0x92/0xf0 [bonding] [ 29.535500][ T1046] bonding_sysfs_store_option+0x8a/0xf0 [bonding] [ 29.536379][ T1046] kernfs_fop_write+0x276/0x410 [ 29.537057][ T1046] vfs_write+0x197/0x4a0 [ 29.537640][ T1046] ksys_write+0x141/0x1d0 [ 29.538251][ T1046] do_syscall_64+0x99/0x4f0 [ 29.538870][ T1046] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 29.539659][ T1046] [ 29.539659][ T1046] other info that might help us debug this: [ 29.539659][ T1046] [ 29.540953][ T1046] Possible unsafe locking scenario: [ 29.540953][ T1046] [ 29.541883][ T1046] CPU0 CPU1 [ 29.542540][ T1046] ---- ---- [ 29.543209][ T1046] lock(&dev->addr_list_lock_key#4); [ 29.543880][ T1046] lock(&dev->addr_list_lock_key#3); [ 29.544873][ T1046] lock(&dev->addr_list_lock_key#4); [ 29.545863][ T1046] lock(&dev->addr_list_lock_key#3); [ 29.546525][ T1046] [ 29.546525][ T1046] *** DEADLOCK *** [ 29.546525][ T1046] [ 29.547542][ T1046] 5 locks held by ifenslave/1046: [ 29.548196][ T1046] #0: ffff88806044c478 (sb_writers#5){.+.+}, at: vfs_write+0x3bb/0x4a0 [ 29.549248][ T1046] #1: ffff88805af00890 (&of->mutex){+.+.}, at: kernfs_fop_write+0x1cf/0x410 [ 29.550343][ T1046] #2: ffff88805b8b54b0 (kn->count#157){.+.+}, at: kernfs_fop_write+0x1f2/0x410 [ 29.551575][ T1046] #3: ffffffffaecf4cf0 (rtnl_mutex){+.+.}, at: bond_opt_tryset_rtnl+0x5f/0xf0 [bonding] [ 29.552819][ T1046] #4: ffff8880460f2280 (&dev->addr_list_lock_key#4){+...}, at: bond_enslave+0x4482/0x47b0 [bonding] [ 29.554175][ T1046] [ 29.554175][ T1046] stack backtrace: [ 29.554907][ T1046] CPU: 0 PID: 1046 Comm: ifenslave Not tainted 5.5.0+ #322 [ 29.555854][ T1046] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 29.557064][ T1046] Call Trace: [ 29.557504][ T1046] dump_stack+0x96/0xdb [ 29.558054][ T1046] check_noncircular+0x371/0x450 [ 29.558723][ T1046] ? print_circular_bug.isra.35+0x310/0x310 [ 29.559486][ T1046] ? hlock_class+0x130/0x130 [ 29.560100][ T1046] ? __lock_acquire+0x2d8d/0x3de0 [ 29.560761][ T1046] __lock_acquire+0x2d8d/0x3de0 [ 29.561366][ T1046] ? register_lock_class+0x14d0/0x14d0 [ 29.562045][ T1046] ? find_held_lock+0x39/0x1d0 [ 29.562641][ T1046] lock_acquire+0x164/0x3b0 [ 29.563199][ T1046] ? dev_mc_sync_multiple+0x95/0x120 [ 29.563872][ T1046] _raw_spin_lock+0x30/0x70 [ 29.564464][ T1046] ? dev_mc_sync_multiple+0x95/0x120 [ 29.565146][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.565793][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.566487][ T1046] ? bond_update_slave_arr+0x940/0x940 [bonding] [ 29.567279][ T1046] ? bstr_printf+0xc20/0xc20 [ 29.567857][ T1046] ? stack_trace_consume_entry+0x160/0x160 [ 29.568614][ T1046] ? deactivate_slab.isra.77+0x2c5/0x800 [ 29.569320][ T1046] ? check_chain_key+0x236/0x5d0 [ 29.569939][ T1046] ? sscanf+0x93/0xc0 [ 29.570442][ T1046] ? vsscanf+0x1e20/0x1e20 [ 29.571003][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ ... ] Fixes: ab92d68fc22f ("net: core: add generic lockdep keys") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16NFC: pn544: Fix a typo in a debug messageChristophe JAILLET
The ending character of the string shoulb be \n, not \b. Fixes: 17936b43f0fd ("NFC: Standardize logging style") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: dsa: b53: Ensure the default VID is untaggedFlorian Fainelli
We need to ensure that the default VID is untagged otherwise the switch will be sending tagged frames and the results can be problematic. This is especially true with b53 switches that use VID 0 as their default VLAN since VID 0 has a special meaning. Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID") Fixes: 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: socket: remove extra call to synchronize_netJason A. Donenfeld
synchronize_net() is a wrapper around synchronize_rcu(), so there's no point in having synchronize_net and synchronize_rcu back to back, despite the documentation comment suggesting maybe it's somewhat useful, "Wait for packets currently being received to be done." This commit removes the extra call. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: send: account for mtu=0 devicesJason A. Donenfeld
It turns out there's an easy way to get packets queued up while still having an MTU of zero, and that's via persistent keep alive. This commit makes sure that in whatever condition, we don't wind up dividing by zero. Note that an MTU of zero for a wireguard interface is something quasi-valid, so I don't think the correct fix is to limit it via min_mtu. This can be reproduced easily with: ip link add wg0 type wireguard ip link add wg1 type wireguard ip link set wg0 up mtu 0 ip link set wg1 up wg set wg0 private-key <(wg genkey) wg set wg1 listen-port 1 private-key <(wg genkey) peer $(wg show wg0 public-key) wg set wg0 peer $(wg show wg1 public-key) persistent-keepalive 1 endpoint 127.0.0.1:1 However, while min_mtu=0 seems fine, it makes sense to restrict the max_mtu. This commit also restricts the maximum MTU to the greatest number for which rounding up to the padding multiple won't overflow a signed integer. Packets this large were always rejected anyway eventually, due to checks deeper in, but it seems more sound not to even let the administrator configure something that won't work anyway. We use this opportunity to clean up this function a bit so that it's clear which paths we're expecting. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: receive: reset last_under_load to zeroJason A. Donenfeld
This is a small optimization that prevents more expensive comparisons from happening when they are no longer necessary, by clearing the last_under_load variable whenever we wind up in a state where we were under load but we no longer are. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Suggested-by: Matt Dunwoodie <ncon@noconroy.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: phy: restore mdio regs in the iproc mdio driverArun Parameswaran
The mii management register in iproc mdio block does not have a retention register so it is lost on suspend. Save and restore value of register while resuming from suspend. Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix out of range usage of active_vlans arrayDmitry Bogdanov
fix static checker warning: drivers/net/ethernet/aquantia/atlantic/aq_filters.c:166 aq_check_approve_fvlan() error: passing untrusted data to 'test_bit()' Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 7975d2aff5af: ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: possible fault in transition to hibernationPavel Belous
during hibernation freeze, aq_nic_stop could be invoked on a stopped device. That may cause panic on access to not yet allocated vector/ring structures. Add a check to stop device if it is not yet stopped. Similiarly after freeze in hibernation thaw, aq_nic_start could be invoked on a not initialized net device. Result will be the same. Add a check to start device if it is initialized. In our case, this is the same as started. Fixes: 8aaa112a57c1 ("net: atlantic: refactoring pm logic") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix potential error handlingPavel Belous
Code inspection found that in case of mapping error we do return current 'ret' value. But beside error, it is used to count number of descriptors allocated for the packet. In that case map_skb function could return '1'. Changing it to return zero (number of mapped descriptors for skb) Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix use after free kasan warnPavel Belous
skb->len is used to calculate statistics after xmit invocation. Under a stress load it may happen that skb will be xmited, rx interrupt will come and skb will be freed, all before xmit function is even returned. Eventually, skb->len will access unallocated area. Moving stats calculation into tx_clean routine. Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Reported-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: better loopback mode handlingNikita Danilov
Add checks to not enable multiple loopback modes simultaneously, It was also discovered that for dma loopback to function correctly promisc mode should be enabled on device. Fixes: ea4b4d7fc106 ("net: atlantic: loopback tests via private flags") Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: ptp gpio adjustmentsEgor Pomozov
Clock adjustment data should be passed to FW as well, otherwise in some cases a drift was observed when using GPIO features. Signed-off-by: Egor Pomozov <epomozov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: check rpc result and wait for rpc addressIgor Russkikh
Artificial HW reliability tests revealed a possible hangup in the driver. Normally, when device disappears from bus, all register reads returns 0xFFFFFFFF. At remote procedure invocation towards FW there is a logic where result is compared with -1 in a loop. That caused an infinite loop if hardware due to some issues disappears from bus. Add extra result checks to prevent this. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: checksum compat issueDmitry Bezrukov
Yet another checksum offload compatibility issue was found. The known issue is that AQC HW marks tcp packets with 0xFFFF checksum as invalid (1). This is workarounded in driver, passing all the suspicious packets up to the stack for further csum validation. Another HW problem (2) is that it hides invalid csum of LRO aggregated packets inside of the individual descriptors. That was workarounded by forced scan of all LRO descriptors for checksum errors. However the scan logic was joint for both LRO and multi-descriptor packets (jumbos). And this causes the issue. We have to drop LRO packets with the detected bad checksum because of (2), but we have to pass jumbo packets to stack because of (1). When using windows tcp partner with jumbo frames but with LSO disabled driver discards such frames as bad checksummed. But only LRO frames should be dropped, not jumbos. On such a configurations tcp stream have a chance of drops and stucks. (1) 76f254d4afe2 ("net: aquantia: tcp checksum 0xffff being handled incorrectly") (2) d08b9a0a3ebd ("net: aquantia: do not pass lro session with invalid tcp checksum") Fixes: d08b9a0a3ebd ("net: aquantia: do not pass lro session with invalid tcp checksum") Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: macb: ensure interface is not suspended on at91rm9200Alexandre Belloni
Because of autosuspend, at91ether_start is called with clocks disabled. Ensure that pm_runtime doesn't suspend the interface as soon as it is opened as there is no pm_runtime support is the other relevant parts of the platform support for at91rm9200. Fixes: d54f89af6cc4 ("net: macb: Add pm runtime support") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16Merge tag 'for-linus-5.6-1' of https://github.com/cminyard/linux-ipmiLinus Torvalds
Pull IPMI update from Corey Minyard: "Minor bug fixes for IPMI I know this is late; I've been travelling and, well, I've been distracted. This is just a few bug fixes and adding i2c support to the IPMB driver, which is something I wanted from the beginning for it" * tag 'for-linus-5.6-1' of https://github.com/cminyard/linux-ipmi: drivers: ipmi: fix off-by-one bounds check that leads to a out-of-bounds write ipmi:ssif: Handle a possible NULL pointer reference drivers: ipmi: Modify max length of IPMB packet drivers: ipmi: Support raw i2c packet in IPMB
2020-02-16Merge tag 'edac_urgent_for_5.6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras Pull EDAC fixes from Borislav Petkov: "Two fixes for use-after-free and memory leaking in the EDAC core, by Robert Richter. Debug options like DEBUG_TEST_DRIVER_REMOVE, KASAN and DEBUG_KMEMLEAK unearthed issues with the lifespan of memory allocated by the EDAC memory controller descriptor due to misdesigned memory freeing, done partially by the EDAC core *and* the driver core, which is problematic to say the least. These two are minimal fixes to take care of stable - a proper rework is following which cleans up that mess properly" * tag 'edac_urgent_for_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras: EDAC/sysfs: Remove csrow objects on errors EDAC/mc: Fix use-after-free and memleaks during device removal
2020-02-16Merge tag 'block-5.6-2020-02-16' of git://git.kernel.dk/linux-blockLinus Torvalds
Pull block fixes from Jens Axboe: "Not a lot here, which is great, basically just three small bcache fixes from Coly, and four NVMe fixes via Keith" * tag 'block-5.6-2020-02-16' of git://git.kernel.dk/linux-block: nvme: fix the parameter order for nvme_get_log in nvme_get_fw_slot_info nvme/pci: move cqe check after device shutdown nvme: prevent warning triggered by nvme_stop_keep_alive nvme/tcp: fix bug on double requeue when send fails bcache: remove macro nr_to_fifo_front() bcache: Revert "bcache: shrink btree node cache after bch_btree_check()" bcache: ignore pending signals when creating gc and allocator thread
2020-02-15Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input updates from Dmitry Torokhov: - a few drivers have been updated to use flexible-array syntax instead of GCC extension - ili210x touchscreen driver now supports the 2120 protocol flavor - a couple more of Synaptics devices have been switched over to RMI4 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: cyapa - replace zero-length array with flexible-array member Input: tca6416-keypad - replace zero-length array with flexible-array member Input: gpio_keys_polled - replace zero-length array with flexible-array member Input: synaptics - remove the LEN0049 dmi id from topbuttonpad list Input: synaptics - enable SMBus on ThinkPad L470 Input: synaptics - switch T470s to RMI4 by default Input: gpio_keys - replace zero-length array with flexible-array member Input: goldfish_events - replace zero-length array with flexible-array member Input: psmouse - switch to using i2c_new_scanned_device() Input: ili210x - add ili2120 support Input: ili210x - fix return value of is_visible function
2020-02-15Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdmaLinus Torvalds
Pull rdma fixes from Jason Gunthorpe: "Not too much going on here, though there are about four fixes related to stuff merged during the last merge window. We also see the return of a syzkaller instance with access to RDMA devices, and a few bugs detected by that squished. - Fix three crashers and a memory memory leak for HFI1 - Several bugs found by syzkaller - A bug fix for the recent QP counters feature on older mlx5 HW - Locking inversion in cxgb4 - Unnecessary WARN_ON in siw - A umad crasher regression during unload, from a bug fix for something else - Bugs introduced in the merge window: - Missed list_del in uverbs file rework, core and mlx5 devx - Unexpected integer math truncation in the mlx5 VAR patches - Compilation bug fix for the VAR patches on 32 bit" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: IB/mlx5: Use div64_u64 for num_var_hw_entries calculation RDMA/core: Fix protection fault in get_pkey_idx_qp_list RDMA/rxe: Fix soft lockup problem due to using tasklets in softirq RDMA/mlx5: Prevent overflow in mmap offset calculations IB/umad: Fix kernel crash while unloading ib_umad RDMA/mlx5: Fix async events cleanup flows RDMA/core: Add missing list deletion on freeing event queue RDMA/siw: Remove unwanted WARN_ON in siw_cm_llp_data_ready() RDMA/iw_cxgb4: initiate CLOSE when entering TERM IB/mlx5: Return failure when rts2rts_qp_counters_set_id is not supported RDMA/core: Fix invalid memory access in spec_filter_size IB/rdmavt: Reset all QPs when the device is shut down IB/hfi1: Close window for pq and request coliding IB/hfi1: Acquire lock to release TID entries when user file is closed RDMA/hfi1: Fix memory leak in _dev_comp_vect_mappings_create
2020-02-15Merge tag 'armsoc-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Olof Johansson: "A handful of fixes that have come in since the merge window: - Fix of PCI interrupt map on arm64 fast model (SW emulator) - Fixlet for sound on ST platforms and a small cleanup of deprecated DT properties - A stack buffer overflow fix for moxtet - Fuse driver build fix for Tegra194 - A few config updates to turn on new drivers merged this cycle" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: bus: moxtet: fix potential stack buffer overflow soc/tegra: fuse: Fix build with Tegra194 configuration ARM: dts: sti: fixup sound frame-inversion for stihxxx-b2120.dtsi ARM: dts: sti: Remove deprecated snps PHY properties for stih410-b2260 arm64: defconfig: Enable DRM_SUN6I_DSI arm64: defconfig: Enable CONFIG_SUN8I_THERMAL ARM: sunxi: Enable CONFIG_SUN8I_THERMAL arm64: defconfig: Set bcm2835-dma as built-in ARM: configs: Cleanup old Kconfig options ARM: npcm: Bring back GPIOLIB support arm64: dts: fast models: Fix FVP PCI interrupt-map property
2020-02-15Merge tag 's390-5.6-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux Pull s390 updates from Vasily Gorbik: - Enable paes-s390 cipher selftests in testmgr (acked-by Herbert Xu). - Fix protected key length update in PKEY_SEC2PROTK ioctl and increase card/queue requests counter to 64-bit in crypto code. - Fix clang warning in get_tod_clock. - Fix ultravisor info length extensions handling. - Fix style of SPDX License Identifier in vfio-ccw. - Avoid unnecessary GFP_ATOMIC and simplify ACK tracking in qdio. * tag 's390-5.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: crypto/testmgr: enable selftests for paes-s390 ciphers s390/time: Fix clk type in get_tod_clock s390/uv: Fix handling of length extensions s390/qdio: don't allocate *aob array with GFP_ATOMIC s390/qdio: simplify ACK tracking s390/zcrypt: fix card and queue total counter wrap s390/pkey: fix missing length of protected key on return vfio-ccw: Use the correct style for SPDX License Identifier
2020-02-15Merge tag 'hwmon-for-v5.6-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging Pull hwmon fixes from Guenter Roeck: "Fix compatible string typos in the xdpe12284 driver, and a wrong bit value in the ltc2978 driver" * tag 'hwmon-for-v5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: hwmon: (pmbus/xdpe12284) fix typo in compatible strings hwmon: (pmbus/ltc2978) Fix PMBus polling of MFR_COMMON definitions.
2020-02-15bus: moxtet: fix potential stack buffer overflowMarek Behún
The input_read function declares the size of the hex array relative to sizeof(buf), but buf is a pointer argument of the function. The hex array is meant to contain hexadecimal representation of the bin array. Link: https://lore.kernel.org/r/20200215142130.22743-1-marek.behun@nic.cz Fixes: 5bc7f990cd98 ("bus: Add support for Moxtet bus") Signed-off-by: Marek Behún <marek.behun@nic.cz> Reported-by: sohu0106 <sohu0106@126.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2020-02-14Input: cyapa - replace zero-length array with flexible-array memberGustavo A. R. Silva
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Link: https://lore.kernel.org/r/20200214172132.GA28389@embeddedor Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2020-02-14Input: tca6416-keypad - replace zero-length array with flexible-array memberGustavo A. R. Silva
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Link: https://lore.kernel.org/r/20200214172022.GA27490@embeddedor Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2020-02-14Input: gpio_keys_polled - replace zero-length array with flexible-array memberGustavo A. R. Silva
The current codebase makes use of the zero-length array language extension to the C90 standard, but the preferred mechanism to declare variable-length types such as these ones is a flexible array member[1][2], introduced in C99: struct foo { int stuff; struct boo array[]; }; By making use of the mechanism above, we will get a compiler warning in case the flexible array does not occur last in the structure, which will help us prevent some kind of undefined behavior bugs from being inadvertently introduced[3] to the codebase from now on. Also, notice that, dynamic memory allocations won't be affected by this change: "Flexible array members have incomplete type, and so the sizeof operator may not be applied. As a quirk of the original implementation of zero-length arrays, sizeof evaluates to zero."[1] This issue was found with the help of Coccinelle. [1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html [2] https://github.com/KSPP/linux/issues/21 [3] commit 76497732932f ("cxgb3/l2t: Fix undefined behaviour") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Link: https://lore.kernel.org/r/20200214171907.GA26588@embeddedor Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2020-02-14scsi: Revert "target: iscsi: Wait for all commands to finish before freeing ↵Bart Van Assche
a session" Since commit e9d3009cb936 introduced a regression and since the fix for that regression was not perfect, revert this commit. Link: https://marc.info/?l=target-devel&m=158157054906195 Cc: Rahul Kundu <rahul.kundu@chelsio.com> Cc: Mike Marciniszyn <mike.marciniszyn@intel.com> Cc: Sagi Grimberg <sagi@grimberg.me> Reported-by: Dakshaja Uppalapati <dakshaja@chelsio.com> Fixes: e9d3009cb936 ("scsi: target: iscsi: Wait for all commands to finish before freeing a session") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-02-14scsi: Revert "RDMA/isert: Fix a recently introduced regression related to ↵Bart Van Assche
logout" Since commit 04060db41178 introduces soft lockups when toggling network interfaces, revert it. Link: https://marc.info/?l=target-devel&m=158157054906196 Cc: Rahul Kundu <rahul.kundu@chelsio.com> Cc: Mike Marciniszyn <mike.marciniszyn@intel.com> Cc: Sagi Grimberg <sagi@grimberg.me> Reported-by: Dakshaja Uppalapati <dakshaja@chelsio.com> Fixes: 04060db41178 ("scsi: RDMA/isert: Fix a recently introduced regression related to logout") Signed-off-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-02-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Fix interrupt name truncation in mv88e6xxx dsa driver, from Andrew Lunn. 2) Process generic XDP even if SKB is cloned, from Toke Høiland-Jørgensen. 3) Fix leak of kernel memory to userspace in smc, from Eric Dumazet. 4) Add some missing netlink attribute validation to matchall and flower, from Davide Caratti. 5) Send icmp responses properly when NAT has been applied to the frame before we get to the tunnel emitting the icmp, from Jason Donenfeld. 6) Make sure there is enough SKB headroom when adding dsa tags for qca and ar9331. From Per Forlin. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits) netdevice.h: fix all kernel-doc and Sphinx warnings net: dsa: tag_ar9331: Make sure there is headroom for tag net: dsa: tag_qca: Make sure there is headroom for tag net, ip6_tunnel: enhance tunnel locate with link check net/smc: no peer ID in CLC decline for SMCD net/smc: transfer fasync_list in case of fallback net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples() net: hns3: fix VF bandwidth does not take effect in some case net: hns3: add management table after IMP reset mac80211: fix wrong 160/80+80 MHz setting cfg80211: add missing policy for NL80211_ATTR_STATUS_CODE xfrm: interface: use icmp_ndo_send helper wireguard: device: use icmp_ndo_send helper sunvnet: use icmp_ndo_send helper gtp: use icmp_ndo_send helper icmp: introduce helper for nat'd source address in network device context net/sched: flower: add missing validation of TCA_FLOWER_FLAGS net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS net/flow_dissector: remove unexist field description page_pool: refill page when alloc.count of pool is zero ...
2020-02-14Merge tag 'pm-5.6-rc2' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull power management fixes from Rafael Wysocki: "Fix three issues related to the handling of wakeup events signaled through the ACPI SCI while suspended to idle (Rafael Wysocki) and unexport an internal cpufreq variable (Yangtao Li)" * tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system ACPICA: Introduce acpi_any_gpe_status_set() ACPI: PM: s2idle: Avoid possible race related to the EC GPE ACPI: EC: Fix flushing of pending work cpufreq: Make cpufreq_global_kobject static
2020-02-14Merge tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drmLinus Torvalds
Pull drm fixes from Dave Airlie: "The core has a build fix for edid code on certain compilers/arches/, one MST fix and one vgem fix. Regular amdgpu fixes, and a couple of small driver fixes. The i915 fixes are bit larger than normal for this stage, but they were having CI issues last week, and they hadn't sent any fixes last week due to this. core: - edid build fix mst: - fix NULL ptr deref vgem: - fix close after free msm: - better dma-api usage sun4i: - disable allow_fb_modifiers amdgpu: - Additional OD fixes for navi - Misc display fixes - VCN 2.5 DPG fix - Prevent build errors on PowerPC on some configs - GDS EDC fix i915: - dsi/acpi fixes - gvt locking and allocation fixes - gem/gt fixes - bios timing parameters fix" * tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drm: (50 commits) drm/i915: Mark the removal of the i915_request from the sched.link drm/i915/execlists: Reclaim the hanging virtual request drm/i915/execlists: Take a reference while capturing the guilty request drm/i915/execlists: Offline error capture drm/i915/gt: Allow temporary suspension of inflight requests drm/i915: Keep track of request among the scheduling lists drm/i915/gem: Tighten checks and acquiring the mmap object drm/i915: Fix preallocated barrier list append drm/i915/gt: Acquire ce->active before ce->pin_count/ce->pin_mutex drm/i915: Tighten atomicity of i915_active_acquire vs i915_active_release drm/i915: Stub out i915_gpu_coredump_put drm/amdgpu:/navi10: use the ODCAP enum to index the caps array drm/amdgpu: update smu_v11_0_pptable.h drm/amdgpu: correct comment to clear up the confusion drm/amd/display: DCN2.x Do not program DPPCLK if same value drm/amd/display: Don't map ATOM_ENABLE to ATOM_INIT drm/amdgpu/vcn2.5: fix warning drm/amdgpu: limit GDS clearing workaround in cold boot sequence drm/amdgpu: fix amdgpu pmu to use hwc->config instead of hwc->conf amdgpu: Prevent build errors regarding soft/hard-float FP ABI tags ...
2020-02-14IB/mlx5: Use div64_u64 for num_var_hw_entries calculationJason Gunthorpe
On i386: ERROR: "__udivdi3" [drivers/infiniband/hw/mlx5/mlx5_ib.ko] undefined! ERROR: "__divdi3" [drivers/infiniband/hw/mlx5/mlx5_ib.ko] undefined! Fixes: f164be8c0366 ("IB/mlx5: Extend caps stage to handle VAR capabilities") Reported-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Reported-by: Alexander Lobakin <alobakin@dlink.ru> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
2020-02-14drm/amdgpu/gfx10: disable gfxoff when reading rlc clockAlex Deucher
Otherwise we readback all ones. Fixes rlc counter readback while gfxoff is active. Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2020-02-14drm/amdgpu/gfx9: disable gfxoff when reading rlc clockAlex Deucher
Otherwise we readback all ones. Fixes rlc counter readback while gfxoff is active. Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2020-02-14drm/amdgpu/soc15: fix xclk for ravenAlex Deucher
It's 25 Mhz (refclk / 4). This fixes the interpretation of the rlc clock counter. Acked-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org
2020-02-14drm/amd/powerplay: always refetch the enabled features status on dpm enablementEvan Quan
Otherwise, the cached dpm features status may be inconsistent under some case(e.g. baco reset of Navi asic). Signed-off-by: Evan Quan <evan.quan@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-02-14drm/amd/display: fix dtm unloadingBhawanpreet Lakha
there was a type in the terminate command. We should be calling psp_dtm_unload() instead of psp_hdcp_unload() Fixes: 143f23053333 ("drm/amdgpu: psp DTM init") Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-02-14drm/amd/display: fix backwards byte order in rx_caps.Bhawanpreet Lakha
We were using incorrect byte order after we started using the drm_defines So fix it. Fixes: 02837a91ae75 ("drm/amd/display: add and use defines from drm_hdcp.h") Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com> Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-02-14nvme: fix the parameter order for nvme_get_log in nvme_get_fw_slot_infoYi Zhang
nvme fw-activate operation will get bellow warning log, fix it by update the parameter order [ 113.231513] nvme nvme0: Get FW SLOT INFO log error Fixes: 0e98719b0e4b ("nvme: simplify the API for getting log pages") Reported-by: Sujith Pandel <sujith_pandel@dell.com> Reviewed-by: David Milburn <dmilburn@redhat.com> Signed-off-by: Yi Zhang <yi.zhang@redhat.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-02-14nvme/pci: move cqe check after device shutdownKeith Busch
Many users have reported nvme triggered irq_startup() warnings during shutdown. The driver uses the nvme queue's irq to synchronize scanning for completions, and enabling an interrupt affined to only offline CPUs triggers the alarming warning. Move the final CQE check to after disabling the device and all registered interrupts have been torn down so that we do not have any IRQ to synchronize. Link: https://bugzilla.kernel.org/show_bug.cgi?id=206509 Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Jens Axboe <axboe@kernel.dk>
generated by cgit (git 2.34.1) at 2025-09-11 19:15:50 +0000