| Age | Commit message (Collapse) | Author |
|---|
|
Add support for MQPRIO channel mode, in which a partition to TCs
is defined over the channels. We allow partitions with contiguous
queue indices, with no holes within. We do not allow modification
to the num of channels while this MQPRIO mode is active.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add handling for failures in netdev_set_num_tc().
Let mlx5e_netdev_set_tcs return an int.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
This is in preparation for supporting MQPRIO CHANNEL mode in
downstream patch, in addition to DCB mode that's supported today.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Abstract the MQPRIO params into a struct.
Use a getter for DCB mode num_tcs.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Extend the existing flow classification support, to steer
flows not only directly to a receive ring, but also into
the new RSS contexts.
Create needed TIR objects on demand, and hold reference
on the RSS context.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add support to multiple RSS contexts. Resources of the non-default
RSS contexts are allocated and created on demand. Each RSS context
can be controlled and configured separately, via the implemented
ethtool ops. Here we limit the num of total contexts to 16.
We do not enforce any kind of new limitation over the indirection table
content. More specifically, two separate contexts can be configured to
fully or partially point to the same set of receive rings.
The default RSS context (index 0) is created with its full set of TIRs.
All other contexts are created with an empty set, then TIRs are added
upon first usage when steering rules are added.
We use a reference counting mechanism to make sure an RSS context is
not removed before the rules pointing to it.
Block ethtool set_channels operations when multiple RSS contexts exist,
as currently the kernel doesn't protect against inconsistent channels
configs that break non-default RSS contexts.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Move from static to dynamic memory allocations for TIR.
This is in preparation to supporting on-demand TIR operations in
downstream patches, where every RSS context will be init with an
empty set of TIRs.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Code related to RSS is now encapsulated into a dedicated object and put
into new files en/rss.{c,h}. All usages are converted.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Bring all fields that define and maintain RSS behavior together
into a new structure.
Align all usages with this new structure. Keep it hidden within
rx_res.c.
This helps supporting multiple RSS contexts in downstream patch.
Use dynamic allocations for the RSS context.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Take TIR control operations in rx_res into functions.
This is in preparation to supporting on-demand TIR operations in
downstream patches.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
All calls to mlx5e_rx_res_rss_set_indir_uniform() occur while the RSS
state is inactive, i.e. the RQT is pointing to the drop RQ, not to the
channels' RQs.
It means that the "apply" part of the function is not called.
Remove this part from the function, and document the change. It will be
useful for next patches in the series, allows code simplifications when
multiple RSS contexts are introduced.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In cmdq mode, packet may be flushed before it is executed, so
the pending flag should be cleared after cmdq packet is done.
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
One mtk_crtc need just one cmdq_handle, so add one cmdq_handle
in mtk_crtc to prevent frequently allocation and free of
cmdq_handle.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
CMDQ is used to update display register in vblank period, so
it should be execute in next vblank. If it fail to execute
in next 2 vblank, tiemout happen.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
In mailbox rx_callback, it pass struct mbox_client to callback
function, but it could not map back to mtk_drm_crtc instance
because struct cmdq_client use a pointer to struct mbox_client:
struct cmdq_client {
struct mbox_client client;
struct mbox_chan *chan;
};
struct mtk_drm_crtc {
/* client instance data */
struct cmdq_client *cmdq_client;
};
so remove struct cmdq_client and let mtk_drm_crtc instance define
mbox_client as:
struct mtk_drm_crtc {
/* client instance data */
struct mbox_client cl;
};
and in rx_callback function, use struct mbox_client to get
struct mtk_drm_crtc.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
rx_callback is a standard mailbox callback mechanism and could cover the
function of proprietary cmdq_task_cb, so use the standard one instead of
the proprietary one.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
|
|
With the patch to separate the gpio driver from the pinctrl driver, now
the pinctrl-rockchip can drop the gpio related codes now.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012146.1119289-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There has spin lock for irq set type already, so drop irq_gc_lock and
irq_gc_unlock.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012135.1119234-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The next version gpio controller on SoCs like rk3568 have more write
mask bits for registers.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012123.1119179-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Store register offsets in the struct rockchip_gpio_regs, this patch
prepare for the driver update for new gpio controller.
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012111.1119125-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch add support for rockchip gpio controller, which is supported
in pinctrl driver in the past.
With this patch, the pinctrl-rockchip driver will drop gpio related
codes and populate platform driver to gpio-rockchip.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816012053.1119069-1-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Store a pointer from the pinctrl device for the gpio bank.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816011948.1118959-4-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Separate struct rockchip_pin_bank to pinctrl-rockchip.h file, which will
be used by gpio-rockchip driver in the future.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816011948.1118959-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Since gate and ungate pclk of gpio has very litte benifit for system
power consumption, just keep it always ungate.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Link: https://lore.kernel.org/r/20210816011948.1118959-2-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add ability for users to specify custom u64 value (bpf_cookie) when creating
BPF link for perf_event-backed BPF programs (kprobe/uprobe, perf_event,
tracepoints).
This is useful for cases when the same BPF program is used for attaching and
processing invocation of different tracepoints/kprobes/uprobes in a generic
fashion, but such that each invocation is distinguished from each other (e.g.,
BPF program can look up additional information associated with a specific
kernel function without having to rely on function IP lookups). This enables
new use cases to be implemented simply and efficiently that previously were
possible only through code generation (and thus multiple instances of almost
identical BPF program) or compilation at runtime (BCC-style) on target hosts
(even more expensive resource-wise). For uprobes it is not even possible in
some cases to know function IP before hand (e.g., when attaching to shared
library without PID filtering, in which case base load address is not known
for a library).
This is done by storing u64 bpf_cookie in struct bpf_prog_array_item,
corresponding to each attached and run BPF program. Given cgroup BPF programs
already use two 8-byte pointers for their needs and cgroup BPF programs don't
have (yet?) support for bpf_cookie, reuse that space through union of
cgroup_storage and new bpf_cookie field.
Make it available to kprobe/tracepoint BPF programs through bpf_trace_run_ctx.
This is set by BPF_PROG_RUN_ARRAY, used by kprobe/uprobe/tracepoint BPF
program execution code, which luckily is now also split from
BPF_PROG_RUN_ARRAY_CG. This run context will be utilized by a new BPF helper
giving access to this user-provided cookie value from inside a BPF program.
Generic perf_event BPF programs will access this value from perf_event itself
through passed in BPF program context.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/bpf/20210815070609.987780-6-andrii@kernel.org
|
|
Turn BPF_PROG_RUN into a proper always inlined function. No functional and
performance changes are intended, but it makes it much easier to understand
what's going on with how BPF programs are actually get executed. It's more
obvious what types and callbacks are expected. Also extra () around input
parameters can be dropped, as well as `__` variable prefixes intended to avoid
naming collisions, which makes the code simpler to read and write.
This refactoring also highlighted one extra issue. BPF_PROG_RUN is both
a macro and an enum value (BPF_PROG_RUN == BPF_PROG_TEST_RUN). Turning
BPF_PROG_RUN into a function causes naming conflict compilation error. So
rename BPF_PROG_RUN into lower-case bpf_prog_run(), similar to
bpf_prog_run_xdp(), bpf_prog_run_pin_on_cpu(), etc. All existing callers of
BPF_PROG_RUN, the macro, are switched to bpf_prog_run() explicitly.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20210815070609.987780-2-andrii@kernel.org
|
|
In order to know the reason of link up failure, add supporting ethtool
extended link state. Driver reads the link status code from firmware if
in link down state and converts it to ethtool extended link state.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a new file hns3_ethtool.h, and move struct type definitions from
hns3_ethtool.c to hns3_ethtool.h.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux into arm/fixes
NXP/FSL SoC driver fixes for v5.14
QE interrupt controller driver
- Convert it to platform_device driver to make it work with fw_devlink
- Fix static analysis issue
* tag 'soc-fsl-fix-v5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/leo/linux:
soc: fsl: qe: fix static checker warning
soc: fsl: qe: convert QE interrupt controller to platform_device
Link: https://lore.kernel.org/r/20210813222305.13663-1-leoyang.li@nxp.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Clang + -Wimplicit-fallthrough warns:
drivers/gpu/drm/radeon/radeon_fb.c:170:2: warning: unannotated
fall-through between switch labels [-Wimplicit-fallthrough]
default:
^
drivers/gpu/drm/radeon/radeon_fb.c:170:2: note: insert 'break;' to avoid
fall-through
default:
^
break;
1 warning generated.
Clang's version of this warning is a little bit more pedantic than
GCC's. Add the missing break to satisfy it to match what has been done
all over the kernel tree.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This version brings along following fixes:
- Ensure DCN save init registers after VM setup
- Fix multi-display support for idle opt workqueue
- Use vblank control events for PSR enable/disable
- Create default dc_sink when fail reading EDID under MST
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Compilation of the workqueue fails if not building with the DCN config
option set.
[How]
Guard calls to the flush with the DCN config option to fix the build.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.
[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.
v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DM initializes VM context after DMCUB initialization.
This results in loss of DCN_VM_CONTEXT registers after z10.
[How]
Notify DMCUB when VM setup is complete, and have DMCUB
save init registers.
v2: squash in CONFIG_DRM_AMD_DC_DCN3_1 fix
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
KFDSVMRangeTest.SetGetAttributesTest randomly fails in stress test.
Note: Google Test filter = KFDSVMRangeTest.*
[==========] Running 18 tests from 1 test case.
[----------] Global test environment set-up.
[----------] 18 tests from KFDSVMRangeTest
[ RUN ] KFDSVMRangeTest.BasicSystemMemTest
[ OK ] KFDSVMRangeTest.BasicSystemMemTest (30 ms)
[ RUN ] KFDSVMRangeTest.SetGetAttributesTest
[ ] Get default atrributes
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure
Value of: expectedDefaultResults[i]
Actual: 4294967295
Expected: outputAttributes[i].value
Which is: 0
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:154: Failure
Value of: expectedDefaultResults[i]
Actual: 4294967295
Expected: outputAttributes[i].value
Which is: 0
/home/yifan/brahma/libhsakmt/tests/kfdtest/src/KFDSVMRangeTest.cpp:152: Failure
Value of: expectedDefaultResults[i]
Actual: 4
Expected: outputAttributes[i].type
Which is: 2
[ ] Setting/Getting atrributes
[ FAILED ]
the root cause is that svm work queue has not finished when svm_range_get_attr is called, thus
some garbage svm interval tree data make svm_range_get_attr get wrong result. Flush work queue before
iterate svm interval tree.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
change the workload type for some cards as it is needed.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This reverts commit 0979d43259e13846d86ba17e451e17fec185d240.
Revert this because it does not apply to all the cards.
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
PSR can disable the HUBP along with the OTG when PSR is active.
We'll hit a pageflip timeout when the OTG is disable because we're no
longer updating the CRTC vblank counter and the pflip high IRQ will
not fire on the flip.
In order to flip the page flip timeout occur we should modify the
enter/exit conditions to match DRM requirements.
[How]
Use our deferred handlers for DRM vblank control to notify DMCU(B)
when it can enable or disable PSR based on whether vblank is disabled or
enabled respectively.
We'll need to pass along the stream with the notification now because
we want to access the CRTC state while the CRTC is locked to get the
stream state prior to the commit.
Retain a reference to the stream so it remains safe to continue to
access and release that reference once we're done with it.
Enable/disable logic follows what we were previously doing in
update_planes.
The workqueue has to be flushed before programming streams or planes
to ensure that we exit out of idle optimizations and PSR before
these events occur if necessary.
To keep the skip count logic the same to avoid FBCON PSR enablement
requires copying the allow condition onto the DM IRQ parameters - a
field that we can actually access from the worker.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
The current implementation for idle optimization support only has a
single work item that gets reshuffled into the system workqueue
whenever we receive an enable or disable event.
We can have mismatched events if the work hasn't been processed or if
we're getting control events from multiple displays at once.
This fixes this issue and also makes the implementation usable for
PSR control - which will be addressed in another patch.
[How]
We need to be able to flush remaining work out on demand for driver stop
and psr disable so create a driver specific workqueue instead of using
the system one. The workqueue will be single threaded to guarantee the
ordering of enable/disable events.
Refactor the queue to allocate the control work and deallocate it
after processing it.
Pass the acrtc directly to make it easier to handle psr enable/disable
in a later patch.
Rename things to indicate that it's not just MALL specific.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
While reading remote EDID via Startech 1-to-4 hub, occasionally we
won't get response in time and won't light up corresponding monitor.
Ideally, we can still add generic modes for userspace to choose to try
to light up the monitor and which is done in
drm_helper_probe_single_connector_modes(). So the main problem here is
that we fail .mode_valid since we don't create remote dc_sink for this
case.
[How]
Also add default dc_sink if we can't get the EDID.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
These registers have different address from other SMU V11 ASICs.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
As the fan control was guarded under manual mode before fan speed
RPM/PWM setting. Thus the extra check is totally redundant.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently, the readout of fan speed pwm is transited into percent-based
and then pwm-based. However, the transition into percent-based is totally
unnecessary and make the final output less accurate.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, we need a new way to
retrieving the fan speed RPM.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, we need a new way to
retrieving the fan speed PWM.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
As the relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, both the RPM and PWM
settings need to be saved.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The relationship "PWM = RPM / smu->fan_max_rpm" between fan speed
PWM and RPM is not true for SMU11 ASICs. So, we need a new way to
perform the fan speed RPM setting.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Delete ras_if->name in the RAS ctx structure and remove related lines.
Signed-off-by: Candice Li <candice.li@amd.com>
Reviewed-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
