| Age | Commit message (Collapse) | Author |
|---|
|
source channel
If CMT instance has at least two channels, one channel will be used
as a clock source and another one used as a clock event device.
In that case, IRQ is not requested for clock source channel so
sh_cmt_clock_event_program_verify() might work incorrectly.
Besides, when a channel is only used for clock source, don't need to
re-set the next match_value since it should be maximum timeout as
it still is.
On the other hand, due to no IRQ, total_cycles is not counted up
when reaches compare match time (timer counter resets to zero),
so sh_cmt_clocksource_read() returns unexpected value.
Therefore, use 64-bit clocksoure's mask for 32-bit or 16-bit variants
will also lead to wrong delta calculation. Hence, this mask should
correspond to timer counter width, and above function just returns
the raw value of timer counter register.
Fixes: bfa76bb12f23 ("clocksource: sh_cmt: Request IRQ for clock event device only")
Fixes: 37e7742c55ba ("clocksource/drivers/sh_cmt: Fix clocksource width for 32-bit machines")
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210422123443.73334-1-niklas.soderlund+renesas@ragnatech.se
|
|
Drivers should count packets they are dropping.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21cefe ("bnxt_en: Implement xmit_more.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit introduces support for NETGEAR ReadyNAS Duo v2.
This device use bit 4 of LED[2:0] Polarity Control Register to indicate
AC Power loss.
For more details about AC loss detection in NETGEAR ReadyNAS Duo v2,
please look at the file:
RND_5.3.13_WW.src/u-boot/board/mv_feroceon/mv_hal/usibootup/usibootup.c
from Netgear GPL sources.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
This commit prepare driver for another device support.
New power_off_cfg structure describes two most important things: name of
mdio bus and pointer to register setting function. It allow to add new
device with different mdio bus node and other phy register config.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Immutable branch between regulator and power-supply for for 5.15
This immutable branch introduces the MT6360 charger driver,
which requires a new linear range helper.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
|
|
Rename ChargeOption macros to match the others for ChargeCurrent and
ChargeVoltage and also separate the command & masks macros from the bits of
interest macros for each command. This macro doesn't introduce any
functional change, only code re-org.
Signed-off-by: Bruno Meneguele <bruno.meneguele@smartgreen.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Read voltage_now via IIO and provide the property.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reported-by: kernel test robot <lkp@intel.com> # missing depends on IIO
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add iio map to allow power driver to read out values as a consumer.
This approach does not block later addition of devicetree support
which would be helpful if there is an in-kernel consumer for AIN0/1.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Add basic support for the battery charger for MT6360 PMIC
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Show the values of the DMASTART and DMAEND registers when dumping status
to help with failure analysis.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Dumping the full CDMA push buffer takes a long time and isn't very
useful since most of the contents are not relevant. Instead only show
the CDMA push buffer entries associated with current jobs.
While at it, tweak the indentation a bit to make the output more
readable.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The host1x debug code uses a mix of phys_addr_t, dma_addr_t and u32 to
represent addresses. However, these addresses are always DMA addresses
so use the appropriate type.
This fixes some issues with how these addresses are displayed, because
they could be truncated in some cases and not show the full address.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
If user specify a large enough value of NBD blocks option, it may trigger
signed integer overflow which may lead to nbd->config->bytesize becomes a
large or small value, zero in particular.
UBSAN: Undefined behaviour in drivers/block/nbd.c:325:31
signed integer overflow:
1024 * 4611686155866341414 cannot be represented in type 'long long int'
[...]
Call trace:
[...]
handle_overflow+0x188/0x1dc lib/ubsan.c:192
__ubsan_handle_mul_overflow+0x34/0x44 lib/ubsan.c:213
nbd_size_set drivers/block/nbd.c:325 [inline]
__nbd_ioctl drivers/block/nbd.c:1342 [inline]
nbd_ioctl+0x998/0xa10 drivers/block/nbd.c:1395
__blkdev_driver_ioctl block/ioctl.c:311 [inline]
[...]
Although it is not a big deal, still silence the UBSAN by limit
the input value.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20210804021212.990223-1-libaokun1@huawei.com
[axboe: dropped unlikely()]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is a race between iterating over requests in
nbd_clear_que() and completing requests in recv_work(),
which can lead to double completion of a request.
To fix it, flush the recv worker before iterating over
the requests and don't abort the completed request
while iterating.
Fixes: 96d97e17828f ("nbd: clear_sock on netlink disconnect")
Reported-by: Jiang Yadong <jiangyadong@bytedance.com>
Signed-off-by: Xie Yongji <xieyongji@bytedance.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Link: https://lore.kernel.org/r/20210813151330.96-1-xieyongji@bytedance.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Clean up a handful of checkpatch warnings:
- static const char * array should probably be static const char * const
- function arguments should have identifier names
- else should follow close brace '}'
- suspect code indent for conditional statements
- unnecessary parentheses in an if condition
- avoid multiple line dereference
- remove debug showing function execution, ftrace can trace these better
- prefer 'long' over 'long int' as the int is unnecessary
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Hyper-V vPCI protocol version 1_4 adds support for create interrupt
v3. Create interrupt v3 essentially makes the size of the vector
field bigger in the message, thereby allowing bigger vector values.
For example, that will come into play for supporting LPI vectors
on ARM, which start at 8192.
Link: https://lore.kernel.org/r/MW4PR21MB20026A6EA554A0B9EC696AA8C0159@MW4PR21MB2002.namprd21.prod.outlook.com
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
|
|
Enable PCIe reference clock. There is no remove function that's why
this should be enough for simple operation.
Normally this clock is enabled by default by firmware but there are
usecases where this clock should be enabled by driver itself.
It is also good that PCIe clock is recorded in a clock framework.
Link: https://lore.kernel.org/r/ee6997a08fab582b1c6de05f8be184f3fe8d5357.1624618100.git.michal.simek@xilinx.com
Fixes: ab597d35ef11 ("PCI: xilinx-nwl: Add support for Xilinx NWL PCIe Host Controller")
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org
|
|
Use the defined variable "dev" to make the code cleaner.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt_ptp.h
9e26680733d5 ("bnxt_en: Update firmware call to retrieve TX PTP timestamp")
9e518f25802c ("bnxt_en: 1PPS functions to configure TSIO pins")
099fdeda659d ("bnxt_en: Event handler for PPS events")
kernel/bpf/helpers.c
include/linux/bpf-cgroup.h
a2baf4e8bb0f ("bpf: Fix potentially incorrect results with bpf_get_local_storage()")
c7603cfa04e7 ("bpf: Add ambient BPF runtime context stored in current")
drivers/net/ethernet/mellanox/mlx5/core/pci_irq.c
5957cc557dc5 ("net/mlx5: Set all field of mlx5_irq before inserting it to the xarray")
2d0b41a37679 ("net/mlx5: Refcount mlx5_irq with integer")
MAINTAINERS
7b637cd52f02 ("MAINTAINERS: fix Microchip CAN BUS Analyzer Tool entry typo")
7d901a1e878a ("net: phy: add Maxlinear GPY115/21x/24x driver")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pre-zeroing the batched commands structure is inefficient, as individual
commands are zeroed later in arm_smmu_cmdq_build_cmd(). The size is quite
large and commonly most commands won't even be used:
struct arm_smmu_cmdq_batch cmds = {};
345c: 52800001 mov w1, #0x0 // #0
3460: d2808102 mov x2, #0x408 // #1032
3464: 910143a0 add x0, x29, #0x50
3468: 94000000 bl 0 <memset>
Stop pre-zeroing the complete structure and only zero the num member.
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1628696966-88386-1-git-send-email-john.garry@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When SMMU_GERROR.CMDQP_ERR is different to SMMU_GERRORN.CMDQP_ERR, it
indicates that one or more errors have been encountered on a command queue
control page interface. We need to traverse all ECMDQs in that control
page to find all errors. For each ECMDQ error handling, it is much the
same as the CMDQ error handling. This common processing part is extracted
as a new function __arm_smmu_cmdq_skip_err().
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210811114852.2429-5-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
One SMMU has only one normal CMDQ. Therefore, this CMDQ is used regardless
of the core on which the command is inserted. It can be referenced
directly through "smmu->cmdq". However, one SMMU has multiple ECMDQs, and
the ECMDQ used by the core on which the command insertion is executed may
be different. So the helper function arm_smmu_get_cmdq() is added, which
returns the CMDQ/ECMDQ that the current core should use. Currently, the
code that supports ECMDQ is not added. just simply returns "&smmu->cmdq".
Many subfunctions of arm_smmu_cmdq_issue_cmdlist() use "&smmu->cmdq" or
"&smmu->cmdq.q" directly. To support ECMDQ, they need to call the newly
added function arm_smmu_get_cmdq() instead.
Note that normal CMDQ is still required until ECMDQ is available.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210811114852.2429-4-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
arm_smmu_cmdq_issue_cmd_with_sync()
The obvious key to the performance optimization of commit 587e6c10a7ce
("iommu/arm-smmu-v3: Reduce contention during command-queue insertion") is
to allow multiple cores to insert commands in parallel after a brief mutex
contention.
Obviously, inserting as many commands at a time as possible can reduce the
number of times the mutex contention participates, thereby improving the
overall performance. At least it reduces the number of calls to function
arm_smmu_cmdq_issue_cmdlist().
Therefore, function arm_smmu_cmdq_issue_cmd_with_sync() is added to insert
the 'cmd+sync' commands at a time.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210811114852.2429-3-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The obvious key to the performance optimization of commit 587e6c10a7ce
("iommu/arm-smmu-v3: Reduce contention during command-queue insertion") is
to allow multiple cores to insert commands in parallel after a brief mutex
contention.
Obviously, inserting as many commands at a time as possible can reduce the
number of times the mutex contention participates, thereby improving the
overall performance. At least it reduces the number of calls to function
arm_smmu_cmdq_issue_cmdlist().
Therefore, use command queue batching helpers to insert multiple commands
at a time.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20210811114852.2429-2-thunder.leizhen@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Currently for iommu_unmap() of large scatter-gather list with page size
elements, the majority of time is spent in flushing of partial walks in
__arm_lpae_unmap() which is a VA based TLB invalidation invalidating
page-by-page on iommus like arm-smmu-v2 (TLBIVA).
For example: to unmap a 32MB scatter-gather list with page size elements
(8192 entries), there are 16->2MB buffer unmaps based on the pgsize (2MB
for 4K granule) and each of 2MB will further result in 512 TLBIVAs (2MB/4K)
resulting in a total of 8192 TLBIVAs (512*16) for 16->2MB causing a huge
overhead.
On qcom implementation, there are several performance improvements for
TLB cache invalidations in HW like wait-for-safe (for realtime clients
such as camera and display) and few others to allow for cache
lookups/updates when TLBI is in progress for the same context bank.
So the cost of over-invalidation is less compared to the unmap latency
on several usecases like camera which deals with large buffers. So,
ASID based TLB invalidations (TLBIASID) can be used to invalidate the
entire context for partial walk flush thereby improving the unmap
latency.
For this example of 32MB scatter-gather list unmap, this change results
in just 16 ASID based TLB invalidations (TLBIASIDs) as opposed to 8192
TLBIVAs thereby increasing the performance of unmaps drastically.
Test on QTI SM8150 SoC for 10 iterations of iommu_{map_sg}/unmap:
(average over 10 iterations)
Before this optimization:
size iommu_map_sg iommu_unmap
4K 2.067 us 1.854 us
64K 9.598 us 8.802 us
1M 148.890 us 130.718 us
2M 305.864 us 67.291 us
12M 1793.604 us 390.838 us
16M 2386.848 us 518.187 us
24M 3563.296 us 775.989 us
32M 4747.171 us 1033.364 us
After this optimization:
size iommu_map_sg iommu_unmap
4K 1.723 us 1.765 us
64K 9.880 us 8.869 us
1M 155.364 us 135.223 us
2M 303.906 us 5.385 us
12M 1786.557 us 21.250 us
16M 2391.890 us 27.437 us
24M 3570.895 us 39.937 us
32M 4755.234 us 51.797 us
Real world data also shows big difference in unmap performance as below:
There were reports of camera frame drops because of high overhead in
iommu unmap without this optimization because of frequent unmaps issued
by camera of about 100MB/s taking more than 100ms thereby causing frame
drops.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Link: https://lore.kernel.org/r/20210811160426.10312-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Will Deacon <will@kernel.org>
|
|
In the numa=off kernel command-line configuration init_chip_info() loops
around the number of chips and attempts to copy the cpumask of that node
which is NULL for all iterations after the first chip.
Hence, store the cpu mask for each chip instead of derving cpumask from
node while populating the "chips" struct array and copy that to the
chips[i].mask
Fixes: 053819e0bf84 ("cpufreq: powernv: Handle throttling due to Pmax capping at chip level")
Cc: stable@vger.kernel.org # v4.3+
Reported-by: Shirisha Ganta <shirisha.ganta1@ibm.com>
Signed-off-by: Pratik R. Sampat <psampat@linux.ibm.com>
Reviewed-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
[mpe: Rename goto label to out_free_chip_cpu_mask]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210728120500.87549-2-psampat@linux.ibm.com
|
|
The Acer Predator Helios series (usually denoted by PHxxx-yy) features
a particular key above the keyboard named "TURBO".
The turbo key does 3 things:
1. Set all fan's speeds to TURBO mode
2. Overclocks the CPU and GPU in the safe range
3. Turn on an LED just below the turbo button
All the above actions are operating using WMI function calls,
and there is no custom OC level for turbo. It acts as a flag
for enabling turbo mode instead of telling processors to use
a specific multiply of power (e.g. 1.3x of power).
I've run some benchmark tests and it worked fine:
GpuTest 0.7.0
http://www.geeks3d.com
Module: FurMark
Normal mode Score: 7289 points (FPS: 121)
Turbo mode Score: 7675 points (FPS: 127)
Settings:
- 1920x1080 fullscreen
- antialiasing: Off
- duration: 60000 ms
Renderer:
- GeForce RTX 2060/PCIe/SSE2
- OpenGL: 4.6.0 NVIDIA 460.32.03
This feature is presented by Acer officially and should not harm
hardware in any case.
A challenging part of implementing this feature is that calling
overclock function requires knowing the exact count of fans
for CPU and GPU of each model, which to the best of my
knowledge is not available in the kernel.
So after checking the official PredatorSense application methods, it
turned out they have provided the software the list of fans in each model.
I have access to the mentioned list, and all similar PH-iii-jj can be
added easily by matching "DMI_PRODUCT_NAME".
Creating a specific file for the Acer gaming features is not possible
because the current in use WMI event GUID is required for the turbo button
and it's not possible to register multiple listeners on a single WMI event.
Signed-off-by: JafarAkhondali <jafar.akhoondali@gmail.com>
Link: https://lore.kernel.org/r/20210812125307.1749207-1-jafar.akhoondali@gmail.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
|
|
soc_device_match() is intended as a last resort, to handle e.g. quirks
that cannot be handled by matching based on a compatible value.
As the device nodes for the Renesas USB 3.0 Peripheral Controller on
R-Car E3 and RZ/G2E do have SoC-specific compatible values, the latter
can and should be used to match against these devices.
This also fixes support for the USB 3.0 Peripheral Controller on the
R-Car E3e (R8A779M6) SoC, which is a different grading of the R-Car E3
(R8A77990) SoC, using the same SoC-specific compatible value.
Fixes: 30025efa8b5e75f5 ("usb: gadget: udc: renesas_usb3: add support for r8a77990")
Fixes: 546970fdab1da5fe ("usb: gadget: udc: renesas_usb3: add support for r8a774c0")
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/760981fb4cd110d7cbfc9dcffa365e7c8b25c6e5.1628696960.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even if the Type-C controller supports PD, it is doable to disable PD
capabilities with the current state machine in TCPM. Without enabling RX
in low-level drivers and with skipping the power negotiation, the port
is eligible to be a non-PD Type-C port. Use new flags whose values are
populated from the device tree to decide the port PD capability. Adding
"pd-disable" property in device tree indicates that the port does not
support PD. If PD is not supported, the device tree property
"typec-power-opmode" shall be added to specify the advertised Rp value
if the port supports SRC role.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210804081917.3390341-3-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_endpoint_maxp() already returns actual max packet size, no need
to AND 0x7ff.
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_endpoint_maxp() only returns the bit[10:0] of wMaxPacketSize
of endpoint descriptor, not includes bit[12:11] anymore, so use
usb_endpoint_maxp_mult() instead.
Meanwhile no need AND 0x7ff when get maxp, remove it.
Fixes: 49db427232fe ("usb: gadget: Add UDC driver for tegra XUSB device mode controller")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-5-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_endpoint_maxp() only returns the bit[10:0] of wMaxPacketSize
of endpoint descriptor, not include bit[12:11] anymore, so use
usb_endpoint_maxp_mult() instead.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Cc: stable@vger.kernel.org
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-4-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_endpoint_maxp() returns actual max packet size, @mult will
always be zero, fix it by using usb_endpoint_maxp_mult() instead
to get mult.
Fixes: 4d79e042ed8b ("usb: mtu3: add support for usb3.1 IP")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-3-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For HS isoc or intr, should use @mult but not @burst
to save mult value.
Fixes: 4d79e042ed8b ("usb: mtu3: add support for usb3.1 IP")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-2-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to HS function is disabled when set as FS, need restore
it when set as SS/SSP.
Fixes: dc4c1aa7eae9 ("usb: mtu3: add ->udc_set_speed()")
Cc: stable@vger.kernel.org
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1628836253-7432-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver neglects to check the result of platform_get_irq()'s calls and
blithely passes the negative error codes to request_threaded_irq() (which
takes *unsigned* IRQ #), causing them both to fail with -EINVAL, overriding
an original error code. Stop calling request_threaded_irq() with the
invalid IRQ #s.
Fixes: c33fad0c3748 ("usb: otg: Adding twl6030-usb transceiver driver for OMAP4430")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/9507f50b-50f1-6dc4-f57c-3ed4e53a1c25@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling request_irq() with the invalid IRQ #s.
Fixes: 0807c500a1a6 ("USB: add Freescale USB OTG Transceiver driver")
Acked-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/b0a86089-8b8b-122e-fd6d-73e8c2304964@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver neglects to check the result of platform_get_irq()'s call and
blithely passes the negative error codes to devm_request_irq() (which takes
*unsigned* IRQ #), causing it to fail with -EINVAL, overriding an original
error code. Stop calling devm_request_irq() with the invalid IRQ #s.
Fixes: 517c4c44b323 ("usb: Add driver to allow any GPIO to be used for 7211 USB signals")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/806d0b1a-365b-93d9-3fc1-922105ca5e61@omp.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's useful to know the total number of underflow events and currently
the debug stats are getting reset each time CRTC is being disabled. Let's
account the overall number of events that doesn't get a reset.
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Display controller (DC) performs isochronous memory transfers, and thus,
has a requirement for a minimum memory bandwidth that shall be fulfilled,
otherwise framebuffer data can't be fetched fast enough and this results
in a DC's data-FIFO underflow that follows by a visual corruption.
The Memory Controller drivers provide facility for memory bandwidth
management via interconnect API. Let's wire up the interconnect API
support to the DC driver in order to fix the distorted display output
on T30 Ouya, T124 TK1 and other Tegra devices.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[treding@nvidia.com: unbreak Tegra186+ display support]
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add support for pin and gpio controller driver for RZ/G2L SoC.
Based on a patch in the BSP by Hien Huynh <hien.huynh.px@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210727112328.18809-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
When configuring a kernel including support for Renesas ARM/ARM64 Socs,
but excluding support for the RZ/N1D SoC, the user is always asked about
the RZ/N1D clock driver. As this driver is already auto-selected when
building a kernel including support for the RZ/N1D SoC, there is no need
to make the CLK_R9A06G032 symbol visible, unless compile-testing.
Align the symbol description with the other symbols.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/4f3d30c730c30546f702715ffc648922a8156703.1628672649.git.geert+renesas@glider.be
|
|
cpumap ABI
Reading /sys/devices/system/cpu/cpuX/nodeX/ returns cpumap and cpulist.
However, the size of this file is limited to PAGE_SIZE because of the
limitation for sysfs attribute.
This patch moves to use bin_attribute to extend the ABI to be more
than one page so that cpumap bitmask and list won't be potentially
trimmed.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20210806110251.560-5-song.bao.hua@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Reading /sys/devices/system/cpu/cpuX/topology/ returns cpu topology.
However, the size of this file is limited to PAGE_SIZE because of
the limitation for sysfs attribute.
This patch moves to use bin_attribute to extend the ABI to be more
than one page so that cpumap bitmask and list won't be potentially
trimmed.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20210806110251.560-4-song.bao.hua@hisilicon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This OTP is read-only and contains various keys used by the console to
decrypt, encrypt or verify various pieces of storage.
Its size depends on the console, it is 128 bytes on the Wii and
1024 bytes on the Wii U (split into eight 128 bytes banks).
It can be used directly by writing into one register and reading from
the other one, without any additional synchronisation.
This driver was written based on reversed documentation, see:
https://wiiubrew.org/wiki/Hardware/OTP
Tested-by: Jonathan Neuschäfer <j.ne@posteo.net> # on Wii
Tested-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr> # on Wii U
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20210810153036.1494-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The error handling code in tpci200_register does not free interface_regs
allocated by ioremap and the current version of error handling code is
problematic.
Fix this by refactoring the error handling code and free interface_regs
when necessary.
Fixes: 43986798fd50 ("ipack: add error handling for ioremap_nocache")
Cc: stable@vger.kernel.org
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210810100323.3938492-2-mudongliangabcd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The function tpci200_register called by tpci200_install and
tpci200_unregister called by tpci200_uninstall are in pair. However,
tpci200_unregister has some cleanup operations not in the
tpci200_register. So the error handling code of tpci200_pci_probe has
many different double free issues.
Fix this problem by moving those cleanup operations out of
tpci200_unregister, into tpci200_pci_remove and reverting
the previous commit 9272e5d0028d ("ipack/carriers/tpci200:
Fix a double free in tpci200_pci_probe").
Fixes: 9272e5d0028d ("ipack/carriers/tpci200: Fix a double free in tpci200_pci_probe")
Cc: stable@vger.kernel.org
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20210810100323.3938492-1-mudongliangabcd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
