| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].
But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The commit ce407afc10 introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.
Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
My recent commits (3782c69d, 324c74a) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.
This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message
ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
As Stanislaw pointed out, my patch
iwlagn: fix a race in the unmapping of the TFDs
solved only part of the problem. The race still exists for TFDs of
the host commands. Fix that too.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue:
vfs: add d_prune dentry operation
vfs: protect i_nlink
filesystems: add set_nlink()
filesystems: add missing nlink wrappers
logfs: remove unnecessary nlink setting
ocfs2: remove unnecessary nlink setting
jfs: remove unnecessary nlink setting
hypfs: remove unnecessary nlink setting
vfs: ignore error on forced remount
readlinkat: ensure we return ENOENT for the empty pathname for normal lookups
vfs: fix dentry leak in simple_fill_super()
|
|
* 'for-linus' of git://github.com/richardweinberger/linux: (90 commits)
um: fix ubd cow size
um: Fix kmalloc argument order in um/vdso/vma.c
um: switch to use of drivers/Kconfig
UserModeLinux-HOWTO.txt: fix a typo
UserModeLinux-HOWTO.txt: remove ^H characters
um: we need sys/user.h only on i386
um: merge delay_{32,64}.c
um: distribute exports to where exported stuff is defined
um: kill system-um.h
um: generic ftrace.h will do...
um: segment.h is x86-only and needed only there
um: asm/pda.h is not needed anymore
um: hw_irq.h can go generic as well
um: switch to generic-y
um: clean Kconfig up a bit
um: a couple of missing dependencies...
um: kill useless argument of free_chan() and free_one_chan()
um: unify ptrace_user.h
um: unify KSTK_...
um: fix gcov build breakage
...
|
|
The commit
target: use a workqueue for I/O completions
accidentally removed setting t_tasks_failed in transport_complete_task.
Add it back in a slightly cleaner way; now it is set for every failed task
instead of special casing the last one completing by using the success
argument directly for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
|
|
The check is wrong here because blk_make_request() returns an
ERR_PTR() and it doesn't return NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
|
|
This patch drops TRANSPORT_FREE_CMD_INTR usage from target core, which
includes the removal of transport_generic_free_cmd_intr() symbol,
TRANSPORT_FREE_CMD_INTR usage in transport_processing_thread(), and
special case LUN_RESET handling to skip TRANSPORT_FREE_CMD_INTR processing
in core_tmr_drain_cmd_list(). We now expect that fabric modules will
use an internal workqueue to provide process context when releasing
se_cmd descriptor resources via transport_generic_free_cmd().
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Madhuranath Iyengar <mni@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
|
|
This patch converts target_core_fabric_ops->check_stop_free() usage in
transport_cmd_check_stop() and associated fabric module usage to
return '1' when the passed se_cmd has been released directly within
->check_stop_free(), or return '0' when the passed se_cmd has not
been released.
This addresses an issue where transport_cmd_finish_abort() ->
transport_cmd_check_stop_to_fabric() was leaking descriptors during
LUN_RESET for modules using ->check_stop_free(), but not directly
releasing se_cmd in all cases.
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
|
|
This patch addresses two issues with non immediate TMR handling in
iscsit_handle_task_mgt_cmd(). The first involves breakage due to
v3.1-rc conversion of iscsit_sequence_cmd(), which upon good status
would hit the iscsit_add_reject_from_cmd() block of code. This patch
adds an explict check for CMDSN_ERROR_CANNOT_RECOVER.
The second adds a check to return when non immediate TMR operation is
detected after iscsit_ack_from_expstatsn(), as iscsit_sequence_cmd()
-> iscsit_execute_cmd() will have called transport_generic_handle_tmr()
for the non immediate TMR case already.
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a missing CMDSN_LOWER_THAN_EXP return check for
iscsit_sequence_cmd() in iscsit_handle_scsi_cmd() that was incorrectly
dropped during the v3.1-rc cleanups to use iscsit_sequence_cmd().
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
After the list_del() in core_tmr_drain_tmr_list(),
core_tmr_release_req() would list_del() the same object again.
Call graph:
core_tmr_drain_tmr_list
transport_cmd_finish_abort_tmr
transport_generic_remove
transport_free_se_cmd
core_tmr_release_req
So use list_del_init(), as list_del() of an initialized list_head is
safe and essentially a nop. In the CONFIG_DEBUG_LIST case, list_del()
actually poisons the list_head, but that is fine as we free the object
directly afterwards.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@risingtidesystems.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
* kill duplicates with drivers/char/Kconfig
* take watchdog one into drivers/watchdog/Kconfig
* take mmapper to arch/um/Kconfig.um
* rename Kconfig.char menu to "UML Character Devices"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Replace remaining direct i_nlink updates with a new set_nlink()
updater function.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Tested-by: Toshiyuki Okajima <toshi.okajima@jp.fujitsu.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Replace direct i_nlink updates with the respective updater function
(inc_nlink, drop_nlink, clear_nlink, inode_dec_link_count).
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
|
|
We need to redefine a connector as "connected" if it matches a window
in the host preferred GUI layout.
Otherwise "smart" window managers would turn on Xorg outputs that we don't
want to be on.
This reinstates the update_layout and adds the following information to
the modesetting system.
a) Connection status <-> Equivalent to real hardware connection status
b) Preferred mode <-> Equivalent to real hardware reading EDID
c) Host window position <-> Equivalent to a real hardware scanout address
dynamic register.
It should be noted that there is no assumption here about what should be
displayed and where. Only how to access the host windows.
This also bumps minor to signal availability of the new IOCTL.
Based on code originally written by Jakob Bornecrantz
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Commit 9e903e085262 ("net: add skb frag size accessors") used frag_size
instead of skb_frag_size in this file.
Fixes this build error:
drivers/net/ethernet/xilinx/ll_temac_main.c: In function 'temac_start_xmit':
drivers/net/ethernet/xilinx/ll_temac_main.c:717:3: error: implicit declaration of function 'frag_size' [-Werror=implicit-function-declaration]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
|
|
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
|
|
* 'next/devel' of git://git.linaro.org/people/arnd/arm-soc: (50 commits)
ARM: tegra: update defconfig
arm/tegra: Harmony: Configure PMC for low-level interrupts
arm/tegra: device tree support for ventana board
arm/tegra: add support for ventana pinmuxing
arm/tegra: prepare Seaboard pinmux code for derived boards
arm/tegra: pinmux: ioremap registers
gpio/tegra: Convert to a platform device
arm/tegra: Convert pinmux driver to a platform device
arm/dt: Tegra: Add pinmux node to tegra20.dtsi
arm/tegra: Prep boards for gpio/pinmux conversion to pdevs
ARM: mx5: fix clock usage for suspend
ARM i.MX entry-macro.S: remove now unused code
ARM i.MX boards: use CONFIG_MULTI_IRQ_HANDLER
ARM i.MX tzic: add handle_irq function
ARM i.MX avic: add handle_irq function
ARM: mx25: Add the missing IIM base definition
ARM i.MX avic: convert to use generic irq chip
mx31moboard: Add poweroff support
ARM: mach-qong: Add watchdog support
ARM: davinci: AM18x: Add wl1271/wlan support
...
Fix up conflicts in:
arch/arm/mach-at91/at91sam9g45.c
arch/arm/mach-mx5/devices-imx53.h
arch/arm/plat-mxc/include/mach/memory.h
|
|
* 'next/timer' of git://git.linaro.org/people/arnd/arm-soc:
clocksource: fixup ux500 build problems
ARM: omap: use __devexit_p in dmtimer driver
ARM: ux500: Reprogram timers upon resume
ARM: plat-nomadik: timer: Export reset functions
ARM: plat-nomadik: timer: Add support for periodic timers
ARM: ux500: Move timer code to separate file
ARM: ux500: add support for clocksource DBX500 PRCMU
clocksource: add DBX500 PRCMU Timer support
ARM: plat-nomadik: MTU sched_clock as an option
ARM: OMAP: dmtimer: add error handling to export APIs
ARM: OMAP: dmtimer: low-power mode support
ARM: OMAP: dmtimer: skip reserved timers
ARM: OMAP: dmtimer: pm_runtime support
ARM: OMAP: dmtimer: switch-over to platform device driver
ARM: OMAP: dmtimer: platform driver
ARM: OMAP2+: dmtimer: convert to platform devices
ARM: OMAP1: dmtimer: conversion to platform devices
ARM: OMAP2+: dmtimer: add device names to flck nodes
ARM: OMAP: Add support for dmtimer v2 ip
|
|
* 'next/driver' of git://git.linaro.org/people/arnd/arm-soc:
hw_random: add driver for atmel true hardware random number generator
ARM: at91: at91sam9g45: add trng clock and platform device
MX53 Enable the AHCI SATA on MX53 SMD board
MX53 Enable the AHCI SATA on MX53 LOCO board
MX53 Enable the AHCI SATA on MX53 ARD board
AHCI Add the AHCI SATA feature on the MX53 platforms
Fix pata imx resource
ARM: imx: Define functions for registering PATA
ARM: imx: Add PATA clock support
ARM: imx: Add PATA resources for other i.MX processors
imx: efika: Enable pata.
imx51: add pata clock
imx51: add pata device
Fix up trivial conflict (new selects next to each other from separate
branches for EFIKA_COMMON) in arch/arm/mach-mx5/Kconfig
|
|
* 'next/cleanup' of git://git.linaro.org/people/arnd/arm-soc: (125 commits)
ARM: mach-mxs: fix machines' initializers order
mmc: mxcmmc: explicitly includes mach/hardware.h
arm/imx: explicitly includes mach/hardware.h in pm-imx27.c
arm/imx: remove mx27_setup_weimcs() from mx27.h
arm/imx: explicitly includes mach/hardware.h in mach-kzm_arm11_01.c
arm/imx: remove mx31_setup_weimcs() from mx31.h
ARM: tegra: devices.c should include devices.h
ARM: tegra: cpu-tegra: unexport two functions
ARM: tegra: cpu-tegra: sparse type fix
ARM: tegra: dma: staticify some tables and functions
ARM: tegra: tegra2_clocks: don't export some tables
ARM: tegra: tegra_powergate_is_powered should be static
ARM: tegra: tegra_rtc_read_ms should be static
ARM: tegra: tegra_init_cache should be static
ARM: tegra: pcie: 0 -> NULL changes
ARM: tegra: pcie: include board.h
ARM: tegra: pcie: don't cast __iomem pointers
ARM: tegra: tegra2_clocks: 0 -> NULL changes
ARM: tegra: tegra2_clocks: don't cast __iomem pointers
ARM: tegra: timer: don't cast __iomem pointers
...
Fix up trivial conflicts in
arch/arm/mach-omap2/Makefile,
arch/arm/mach-u300/{Makefile.boot,core.c}
arch/arm/plat-{mxc,omap}/devices.c
|
|
* 'next/fixes' of git://git.linaro.org/people/arnd/arm-soc: (28 commits)
ARM: pxa/cm-x300: properly set bt_reset pin
ARM: mmp: rename SHEEVAD to GPLUGD
ARM: imx: Fix typo 'MACH_MX31_3DS_MXC_NAND_USE_BBT'
ARM: i.MX28: shift frac value in _CLK_SET_RATE
plat-mxc: iomux-v3.h: implicitly enable pull-up/down when that's desired
ARM: mx5: fix clock usage for suspend
ARM: pxa: use correct __iomem annotations
ARM: pxa: sharpsl pm needs SPI
ARM: pxa: centro and treo680 need palm27x
ARM: pxa: make pxafb_smart_*() empty when not enabled
ARM: pxa: select POWER_SUPPLY on raumfeld
ARM: pxa: pxa95x is incompatible with earlier pxa
ARM: pxa: CPU_FREQ_TABLE is needed for CPU_FREQ
ARM: pxa: pxa95x/saarb depends on pxa3xx code
ARM: pxa: allow selecting just one of TREO680/CENTRO
ARM: pxa: export symbols from pxa3xx-ulpi
ARM: pxa: make zylonite_pxa*_init declaration match code
ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available
ARM: at91: add defconfig for at91sam9g45 family
ARM: at91: remove dependency for Atmel PWM driver selector in Kconfig
...
|
|
Based on a patch by Mark Wu <dwu@redhat.com>
Current index allocation in virtio-blk is based on a monotonically
increasing variable "index". This means we'll run out of numbers
after a while. It also could cause confusion about the disk
name in the case of hot-plugging disks.
Change virtio-blk to use ida to allocate index, instead.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This patch, based on virtio PCI driver, adds support for memory
mapped (platform) virtio device. This should allow environments
like qemu to use virtio-based block & network devices even on
platforms without PCI support.
One can define and register a platform device which resources
will describe memory mapped control registers and "mailbox"
interrupt. Such device can be also instantiated using the Device
Tree node with compatible property equal "virtio,mmio".
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Michael S.Tsirkin <mst@redhat.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
For the MSI but non-per_vq_vector case, the config/change vq
also gets added to the list of vqs that need to process the
MSI interrupt. This is not needed as config has it's own
handler (vp_config_changed). In any case, vring_interrupt()
finds nothing needs to be done on this vq.
I tested this patch by testing the "Fallback:" and "Finally
fall back" cases in vp_find_vqs(). Please review.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
On s390 I have seen some random
"Warning: unable to open an initial console"
boot failure. Turns out that tty_open fails, because the
hvc_alloc was not yet done. In former times this could not happen,
since the probe function automatically called hvc_alloc. With newer
versions (multiport) some host<->guest interaction is required
before hvc_alloc is called. This might be too late, especially if
an initramfs is involved. Lets use a completion if we have
multiport and an early console.
[Amit:
* Use NULL instead of 0 for pointer comparison
* Rename 'port_added' to 'early_console_added'
* Re-format, re-word commit message
* Rebase patch on top of current queue]
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Chrstian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This commit adds port-specific stats for the number of bytes received,
sent and discarded. They're exposed via the debugfs interface. This
data can be used to check for data loss bugs (or disprove such claims).
It can also be used for accounting, if there's such a need.
The stats remain valid throughout the lifetime of the port. Unplugging
a port will reset the stats. The numbers are not reset across port
opens/closes.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
discard_port_data() used virtqueue_get_buf() directly instead of using
get_inbuf(). Fix this, so that we get accounting for all received
bytes. This also simplifies the code a lot.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
'ret' is a misnomer in discard_port_data() since we don't return the
value. Rename it to 'err'.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Instead of pulling in a buffer from the vq each time it's called,
get_inbuf() now checks if the current active buffer, in port->inbuf is
valid. If it is, just returns a pointer to it. This ends up
simplifying a lot of code calling get_inbuf() since the check for
port->inbuf being valid was done by all the callers.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
get_inbuf() returns void *. There's no reason to return void pointers
instead of the correct struct port_buffer *.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Get ready to support suspend/resume by using the freezable calls so that
blocking read/write syscalls are handled properly across suspend/resume.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
We don't allow port name changes dynamically for a port. So any
requests by the host to change the name are ignored.
Before this patch, if the hypervisor sent a port name while we had one
set already, we would leak memory equivalent to the size of the old
name.
This scenario wasn't expected so far, but with the suspend-resume
support, we'll send the VIRTIO_CONSOLE_PORT_READY message after restore,
which can get us into this situation.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Convert spaces to tabs and fix indentation for an if statement split
into multiple lines.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This patch modifies virtio-net to use virtio_config_val() instead
of a 'if(virtio_has_feature()) vdev->config->get()' construct to retrieve
optional values from the config space.
Cc: Amit Shah <amit.shah@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
This patch modifies virtio-console to use virtio_config_val() instead
of a 'if(virtio_has_feature()) vdev->config->get()' construct to retrieve
optional values from the config space.
Cc: Amit Shah <amit.shah@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Macintosh CS89x0 based ethernet cards use a Crystal Semiconductor (Now
Cirrus Logic) CS89x0 chip, so the mac89x0 driver should be in
drivers/net/ethernet/cirrus instead of drivers/net/ethernet/apple.
This also fixes a build problem, as the driver needs a header file from the
cirrus directory:
drivers/net/ethernet/apple/mac89x0.c:107:20: error: cs89x0.h: No such file or directory
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.
Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linux: (47 commits)
i2c-s3c2410: Add device tree support
i2c-s3c2410: Keep a copy of platform data and use it
i2c-nomadik: cosmetic coding style corrections
i2c-au1550: dev_pm_ops conversion
i2c-au1550: increase timeout waiting for master done
i2c-au1550: remove unused ack_timeout
i2c-au1550: remove usage of volatile keyword
i2c-tegra: __iomem annotation fix
i2c-eg20t: Add initialize processing in case i2c-error occurs
i2c-eg20t: Fix flag setting issue
i2c-eg20t: add stop sequence in case wait-event timeout occurs
i2c-eg20t: Separate error processing
i2c-eg20t: Fix 10bit access issue
i2c-eg20t: Modify returned value s32 to long
i2c-eg20t: Fix bus-idle waiting issue
i2c-designware: Fix PCI core warning on suspend/resume
i2c-designware: Add runtime power management support
i2c-designware: Add support for Designware core behind PCI devices.
i2c-designware: Push all register reads/writes into the core code.
i2c-designware: Support multiple cores using same ISR
...
|
|
* 'for-linus' of git://opensource.wolfsonmicro.com/regulator: (22 commits)
regulator: Constify constraints name
regulator: Fix possible nullpointer dereference in regulator_enable()
regulator: gpio-regulator add dependency on GENERIC_GPIO
regulator: Add module.h include to gpio-regulator
regulator: Add driver for gpio-controlled regulators
regulator: remove duplicate REG_CTRL2 defines in tps65023
regulator: Clarify documentation for regulator-regulator supplies
regulator: Fix some bitrot in the machine driver documentation
regulator: tps65023: Added support for the similiar TPS65020 chip
regulator: tps65023: Setting correct core regulator for tps65021
regulator: tps65023: Set missing bit for update core-voltage
regulator: tps65023: Fixes i2c configuration issues
regulator: Add debugfs file showing the supply map table
regulator: tps6586x: add SMx slew rate setting
regulator: tps65023: Fixes i2c configuration issues
regulator: tps6507x: Remove num_voltages array
regulator: max8952: removed unused mutex.
regulator: fix regulator/consumer.h kernel-doc warning
regulator: Ensure enough enable time for max8649
regulator: 88pm8607: Fix off-by-one value range checking in the case of no id is matched
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: fix isochronous DMA synchronization
firewire: ohci: work around selfID junk due to wrong gap count
firewire: net: Use posted writes
firewire: use clamp and min3 macros
firewire: ohci: optimize TSB41BA3D detection
firewire: ohci: TSB41BA3D support tweaks
firewire: ohci: Add support for TSB41BA3D phy
firewire: ohci: Move code from the bus reset tasklet into a workqueue
firewire: sbp2: fold two functions into one
firewire: sbp2: move some code to more sensible places
firewire: sbp2: remove obsolete reference counting
|
|
That should probably be 'CONFIG_DE_AOC'.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
