| Age | Commit message (Collapse) | Author |
|---|
|
Function bias_combo getter/setters already handle all cases advanced drive
configuration, include drive for I2C related pins.
Signed-off-by: Guodong Liu <guodong.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220624133700.15487-5-guodong.liu@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
1. I2C pins's resistance value can be controlled by rsel register.
This patch provides rsel (resistance selection) setting on mt8192.
2. Also add the missing pull type array for mt8192 to document the
pull type of each pin and prevent invalid pull type settings.
Signed-off-by: Guodong Liu <guodong.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220624133700.15487-4-guodong.liu@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch provides the advanced drive raw data setting version
for I2C used pins on mt8192.
Signed-off-by: Guodong Liu <guodong.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220624133700.15487-3-guodong.liu@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
1. The dt-binding expects that drive-strength arguments be passed
in mA, but the driver was expecting raw values. And that this
commit changes the driver so that it is aligned with the binding.
2. This commit provides generic driving setup, which support
2/4/6/8/10/12/14/16mA driving, original driver just set raw data
setup setting when use drive-strength property.
Signed-off-by: Guodong Liu <guodong.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220624133700.15487-2-guodong.liu@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Commit 6c846d026d49 ("gpio: Don't fiddle with irqchips marked as
immutable") added a warning to indicate if the gpiolib is altering the
internals of irqchips. The bcm2835 pinctrl is also affected by this
warning.
Fix this by making the irqchip in the bcm2835 pinctrl driver immutable.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220614202831.236341-3-stefan.wahren@i2se.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The commit b8a19382ac62 ("pinctrl: bcm2835: Fix support for threaded level
triggered IRQs") assigned the irq_mask/unmask callbacks with the
already existing functions for irq_enable/disable. The wasn't completely
the right way (tm) to fix the issue, because these callbacks shouldn't
be identical. So fix this by rename the functions to represent their
intension and drop the unnecessary irq_enable/disable assigment.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220614202831.236341-2-stefan.wahren@i2se.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
GPIO 31, 32 can be muxed to GCC_CAMSS_GP(1,2)_CLK respectively but the
function was never assigned to the pingroup (even though the function
exists already).
Add this mode to the related pins.
Fixes: 5373a2c5abb6 ("pinctrl: qcom: Add msm8916 pinctrl driver")
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220612145955.385787-4-nikita@trvn.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Update lpass lpi pin control driver, with clock optional check for ADSP
disabled platforms. This check required for distingushing ADSP based
platforms and ADSP bypass platforms.
In case of ADSP enabled platforms, where audio is routed through ADSP
macro and decodec GDSC Switches are triggered as clocks by pinctrl
driver and ADSP firmware controls them. So It's mandatory to enable
them in ADSP based solutions.
In case of ADSP bypass platforms clock voting is optional as these macro
and dcodec GDSC switches are maintained as power domains and operated from
lpass clock drivers.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/1654921357-16400-3-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
There are no more used members in the struct intel_pingroup, drop them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since struct intel_pingroup got a new member, switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since struct intel_pingroup got a new member, switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since struct intel_pingroup got a new member, switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since struct intel_pingroup got a new member, switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Since struct intel_pingroup got a new member, switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Add a new member to the struct intel_pingroup to cover generic
pin control group parameters. The idea is to convert all users
(one-by-one) to it and drop old members later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak."
Fixes: c2f6d059abfc ("pinctrl: nomadik: refactor DT parser to take two paths")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220607111602.57355-1-linmq006@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
None of the sunxi pin controllers have a module reset line. All of the
SoC documentation, where available, agrees. The bits that would be used
for the PIO reset (i.e. matching the order of the clock gate bits) are
always reserved, both in the CCU and in the PRCM. And experiments on
several SoCs, including the A33, confirm that those reserved bits indeed
have no effect.
Let's remove this superfluous code and dependency, and also remove the
include statement that was copied to the other r_pio drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220531053623.43851-2-samuel@sholland.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Provide pinmux functionality by implementing pinmux_ops.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220601152900.1012813-7-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Presently there is no way to change pinmux configuration run time.
Hence add a function to get IOMUX resource which can be used to
configure IOMUX GPIO pins run time.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220601152900.1012813-6-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
AMD pingroup can be extended to support multi-function pins.
Hence define and use a macro "AMD_PINS" to represent larger
number of pins.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220601152900.1012813-5-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
AMD pingroup can be extended to support multi-function pins.
Hence use PINCTRL_PINGROUP to manage and represent larger
number of pingroups inline.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220601152900.1012813-4-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove 'struct amd_pingroup' and instead use 'struct pingroup'.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220601152900.1012813-3-Basavaraj.Natikar@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pin status reported by pinconf-pins file always reported pin status as
"input enabled" even for pins which had input disabled. Fix this by
returning -EINVAL for the pins which have input disabled.
Fixes: c4c4637eb57f2 ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Reported-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220511094057.3151-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull file descriptor fix from Al Viro:
"Fix for breakage in #work.fd this window"
* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the breakage in close_fd_get_file() calling conventions change
|
|
It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table. New variant doesn't, and callers need to be adjusted.
Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com
Fixes: 6319194ec57b ("Unify the primitives for file descriptor closing")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull clockevent/clocksource updates from Thomas Gleixner:
- Device tree bindings for MT8186
- Tell the kernel that the RISC-V SBI timer stops in deeper power
states
- Make device tree parsing in sp804 more robust
- Dead code removal and tiny fixes here and there
- Add the missing SPDX identifiers
* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
clocksource/drivers/timer-sun5i: Convert to SPDX identifier
clocksource/drivers/timer-sun4i: Convert to SPDX identifier
clocksource/drivers/pistachio: Convert to SPDX identifier
clocksource/drivers/orion: Convert to SPDX identifier
clocksource/drivers/lpc32xx: Convert to SPDX identifier
clocksource/drivers/digicolor: Convert to SPDX identifier
clocksource/drivers/armada-370-xp: Convert to SPDX identifier
clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
clocksource/drivers/jcore: Convert to SPDX identifier
clocksource/drivers/bcm_kona: Convert to SPDX identifier
clocksource/drivers/sp804: Avoid error on multiple instances
clocksource/drivers/riscv: Events are stopped during CPU suspend
clocksource/drivers/ixp4xx: Drop boardfile probe path
dt-bindings: timer: Add compatible for Mediatek MT8186
|
|
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes plus other trivial updates.
The major change of note is moving ufs out of scsi and a minor update
to lpfc vmid handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: qla2xxx: Remove unused 'ql_dm_tgt_ex_pct' parameter
scsi: qla2xxx: Remove setting of 'req' and 'rsp' parameters
scsi: mpi3mr: Fix kernel-doc
scsi: lpfc: Add support for ATTO Fibre Channel devices
scsi: core: Return BLK_STS_TRANSPORT for ALUA transitioning
scsi: sd_zbc: Prevent zone information memory leak
scsi: sd: Fix potential NULL pointer dereference
scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
scsi: myrb: Fix up null pointer access on myrb_cleanup()
scsi: core: Unexport scsi_bus_type
scsi: sd: Don't call blk_cleanup_disk() in sd_probe()
scsi: ufs: ufshcd: Delete unnecessary NULL check
scsi: isci: Fix typo in comment
scsi: pmcraid: Fix typo in comment
scsi: smartpqi: Fix typo in comment
scsi: qedf: Fix typo in comment
scsi: esas2r: Fix typo in comment
scsi: storvsc: Fix typo in comment
scsi: ufs: Split the drivers/scsi/ufs directory
scsi: qla1280: Remove redundant variable
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux
Pull hardware timestamping subsystem from Thierry Reding:
"This contains the new HTE (hardware timestamping engine) subsystem
that has been in the works for a couple of months now.
The infrastructure provided allows for drivers to register as hardware
timestamp providers, while consumers will be able to request events
that they are interested in (such as GPIOs and IRQs) to be timestamped
by the hardware providers.
Note that this currently supports only one provider, but there seems
to be enough interest in this functionality and we expect to see more
drivers added once this is merged"
[ Linus Walleij mentions the Intel PMC in the Elkhart and Tiger Lake
platforms as another future timestamp provider ]
* tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: timestamp: Correct id path
dt-bindings: Renamed hte directory to timestamp
hte: Uninitialized variable in hte_ts_get()
hte: Fix off by one in hte_push_ts_ns()
hte: Fix possible use-after-free in tegra_hte_test_remove()
hte: Remove unused including <linux/version.h>
MAINTAINERS: Add HTE Subsystem
hte: Add Tegra HTE test driver
tools: gpio: Add new hardware clock type
gpiolib: cdev: Add hardware timestamp clock type
gpio: tegra186: Add HTE support
gpiolib: Add HTE support
dt-bindings: Add HTE bindings
hte: Add Tegra194 HTE kernel provider
drivers: Add hardware timestamp engine (HTE) subsystem
Documentation: Add HTE subsystem guide
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull file descriptor updates from Al Viro.
- Descriptor handling cleanups
* tag 'pull-18-rc1-work.fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Unify the primitives for file descriptor closing
fs: remove fget_many and fput_many interface
io_uring_enter(): don't leave f.flags uninitialized
|
|
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull more parisc architecture updates from Helge Deller:
"A fix to prevent crash at bootup if CONFIG_SCHED_MC is enabled, and
add auto-detection of primary graphics card for framebuffer driver"
* tag 'for-5.19/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc/stifb: Keep track of hardware path of graphics card
parisc/stifb: Implement fb_is_primary_device()
parisc: fix a crash with multicore scheduler
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
"Two cleanup patches for Xen related code and (more important) an
update of MAINTAINERS for Xen, as Boris Ostrovsky decided to step
down"
* tag 'for-linus-5.19-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: replace xen_remap() with memremap()
MAINTAINERS: Update Xen maintainership
xen: switch gnttab_end_foreign_access() to take a struct page pointer
|
|
Keep the pa_path (hardware path) of the graphics card in sti_struct and use
this info to give more useful info which card is currently being used.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
|
|
Implement fb_is_primary_device() function, so that fbcon detects if this
framebuffer belongs to the default graphics card which was used to start
the system.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- use the correct register for regcache sync in gpio-pca953x
- remove unused and potentially harmful code from gpio-adp5588
- MAINTAINERS update
* tag 'gpio-fixes-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: adp5588: Remove support for platform setup and teardown callbacks
gpio: pca953x: use the correct register address to do regcache sync
MAINTAINERS: Update Intel GPIO (PMIC and PCH) to Supported
MAINTAINERS: Update GPIO ACPI library to Supported
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull ptrace_stop cleanups from Eric Biederman:
"While looking at the ptrace problems with PREEMPT_RT and the problems
Peter Zijlstra was encountering with ptrace in his freezer rewrite I
identified some cleanups to ptrace_stop that make sense on their own
and move make resolving the other problems much simpler.
The biggest issue is the habit of the ptrace code to change
task->__state from the tracer to suppress TASK_WAKEKILL from waking up
the tracee. No other code in the kernel does that and it is straight
forward to update signal_wake_up and friends to make that unnecessary.
Peter's task freezer sets frozen tasks to a new state TASK_FROZEN and
then it stores them by calling "wake_up_state(t, TASK_FROZEN)" relying
on the fact that all stopped states except the special stop states can
tolerate spurious wake up and recover their state.
The state of stopped and traced tasked is changed to be stored in
task->jobctl as well as in task->__state. This makes it possible for
the freezer to recover tasks in these special states, as well as
serving as a general cleanup. With a little more work in that
direction I believe TASK_STOPPED can learn to tolerate spurious wake
ups and become an ordinary stop state.
The TASK_TRACED state has to remain a special state as the registers
for a process are only reliably available when the process is stopped
in the scheduler. Fundamentally ptrace needs acess to the saved
register values of a task.
There are bunch of semi-random ptrace related cleanups that were found
while looking at these issues.
One cleanup that deserves to be called out is from commit 57b6de08b5f6
("ptrace: Admit ptrace_stop can generate spuriuos SIGTRAPs"). This
makes a change that is technically user space visible, in the handling
of what happens to a tracee when a tracer dies unexpectedly. According
to our testing and our understanding of userspace nothing cares that
spurious SIGTRAPs can be generated in that case"
* tag 'ptrace_stop-cleanup-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sched,signal,ptrace: Rework TASK_TRACED, TASK_STOPPED state
ptrace: Always take siglock in ptrace_resume
ptrace: Don't change __state
ptrace: Admit ptrace_stop can generate spuriuos SIGTRAPs
ptrace: Document that wait_task_inactive can't fail
ptrace: Reimplement PTRACE_KILL by always sending SIGKILL
signal: Use lockdep_assert_held instead of assert_spin_locked
ptrace: Remove arch_ptrace_attach
ptrace/xtensa: Replace PT_SINGLESTEP with TIF_SINGLESTEP
ptrace/um: Replace PT_DTRACE with TIF_SINGLESTEP
signal: Replace __group_send_sig_info with send_signal_locked
signal: Rename send_signal send_signal_locked
|
|
Commit 23cfbc6ec44e ("firmware: Add the support for ZSTD-compressed
firmware files") added support for ZSTD compression, but in the process
also made the previously default XZ compression a config option.
That means that anybody who upgrades their kernel and does a
make oldconfig
to update their configuration, will end up without the XZ compression
that the configuration used to have.
Add the 'default y' to make sure this doesn't happen.
The whole compression question should probably be improved upon, since
it is now possible to "enable" compression in the kernel config but not
enable any actual compression algorithm, which makes it all very
useless. It makes no sense to ask Kconfig questions that enable
situations that are nonsensical like that.
This at least fixes the immediate problem of a kernel update resulting
in a nonbootable machine because of a missed option.
Fixes: 23cfbc6ec44e ("firmware: Add the support for ZSTD-compressed firmware files")
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fixes for a memory leak
UBI:
- Fixes for fastmap (UAF, high CPU usage)
UBIFS:
- Minor cleanups"
* tag 'for-linus-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: ubi_create_volume: Fix use-after-free when volume creation failed
ubi: fastmap: Check wl_pool for free peb before wear leveling
ubi: fastmap: Fix high cpu usage of ubi_bgt by making sure wl_pool not empty
ubifs: Use NULL instead of using plain integer as pointer
ubifs: Simplify the return expression of run_gc()
jffs2: fix memory leak in jffs2_do_fill_super
jffs2: Use kzalloc instead of kmalloc/memset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull initial Loongarch architecture code from Arnd Bergmann:
"This is the majority of the loongarch architecture code, including the
final system call interface and all core functionality.
It still misses three sets of peripheral but vital patches to add
support for other subsystems, which have yet to pass review:
- The drivers/firmware/efi stub for booting from a standard UEFI
firmware implementation. Both the original custom boot interface
and a draft implementation of the EFI stub did not make it, so it
is currently impossible to boot the kernel, until the loongarch
specific portions get accepted into the UEFI subsystem
- The drivers/irqchip/irq-loongson-*.c drivers are shared with the
the MIPS port, but currently lack support for ACPI based booting,
which will get merged through the irqchip subsystem.
- Similarly, the drivers/pci/controller/pci-loongson.c needs to be
modified for ACPI support, which will be merged through the PCI
subsystem.
While the port cannot actually be used before all the above are
merged, having it in 5.19 helps to establish the user space ABI for
the libc ports to build on, and to help any treewide changes in the
mainline kernel get applied here as well.
A gcc-12 based tool chains for build testing is now included in
https://mirrors.edge.kernel.org/pub/tools/crosstool/"
Original description from Huacai Chen:
"LoongArch is a new RISC ISA, which is a bit like MIPS or RISC-V.
LoongArch includes a reduced 32-bit version (LA32R), a standard 32-bit
version (LA32S) and a 64-bit version (LA64). LoongArch use ACPI as its
boot protocol LoongArch-specific interrupt controllers (similar to APIC)
are already added in the next revision of ACPI Specification (current
revision is 6.4).
This patchset is adding basic LoongArch support in mainline kernel, we
can see a complete snapshot here:
https://github.com/loongson/linux/tree/loongarch-next
https://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson.git/log/?h=loongarch-next
Cross-compile tool chain to build kernel:
https://github.com/loongson/build-tools/releases/download/2021.12.21/loongarch64-clfs-2022-03-03-cross-tools-gcc-glibc.tar.xz
A CLFS-based Linux distro:
https://github.com/loongson/build-tools/releases/download/2021.12.21/loongarch64-clfs-system-2022-03-03.tar.bz2
Open-source tool chain which is under review (Binutils and Gcc are already upstream):
https://github.com/loongson/binutils-gdb/tree/upstream_v3.1
https://github.com/loongson/gcc/tree/loongarch_upstream_v6.3
https://github.com/loongson/glibc/tree/loongarch_2_35_dev_v2.2
Loongson and LoongArch documentations:
https://github.com/loongson/LoongArch-Documentation
LoongArch-specific interrupt controllers:
https://mantis.uefi.org/mantis/view.php?id=2203
https://mantis.uefi.org/mantis/view.php?id=2313"
Link: https://lore.kernel.org/lkml/20220603072053.35005-1-chenhuacai@loongson.cn/
* tag 'loongarch-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (24 commits)
MAINTAINERS: Add maintainer information for LoongArch
LoongArch: Add Loongson-3 default config file
LoongArch: Add Non-Uniform Memory Access (NUMA) support
LoongArch: Add multi-processor (SMP) support
LoongArch: Add VDSO and VSYSCALL support
LoongArch: Add some library functions
LoongArch: Add misc common routines
LoongArch: Add ELF and module support
LoongArch: Add signal handling support
LoongArch: Add system call support
LoongArch: Add memory management
LoongArch: Add process management
LoongArch: Add exception/interrupt handling
LoongArch: Add boot and setup routines
LoongArch: Add other common headers
LoongArch: Add atomic/locking headers
LoongArch: Add CPU definition headers
LoongArch: Add build infrastructure
LoongArch: Add writecombine support for drm
LoongArch: Add ELF-related definitions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi
Pull more EFI updates from Ard Biesheuvel:
"Follow-up tweaks for EFI changes - they mostly address issues
introduced this merge window, except for Heinrich's patch:
- fix new DXE service invocations for mixed mode
- use correct Kconfig symbol when setting PE header flag
- clean up the drivers/firmware/efi Kconfig dependencies so that
features that depend on CONFIG_EFI are hidden from the UI when the
symbol is not enabled.
Also included is a RISC-V bugfix from Heinrich to avoid read-write
mappings of read-only firmware regions in the EFI page tables"
* tag 'efi-next-for-v5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: clean up Kconfig dependencies on CONFIG_EFI
efi/x86: libstub: Make DXE calls mixed mode safe
efi: x86: Fix config name for setting the NX-compatibility flag in the PE header
riscv: read-only pages should not be writable
|
|
Since we had to effectively reverted
commit 35a672363ab3 ("driver core: Ensure wait_for_device_probe() waits
until the deferred_probe_timeout fires") in an earlier patch, a non-zero
deferred_probe_timeout will break NFS rootfs mounting [1] again. So, set
the default back to zero until we can fix that.
[1] - https://lore.kernel.org/lkml/TYAPR01MB45443DF63B9EF29054F7C41FD8C60@TYAPR01MB4544.jpnprd01.prod.outlook.com/
Fixes: 2b28a1a84a0e ("driver core: Extend deferred probe timeout on driver registration")
Cc: Mark Brown <broonie@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220526034609.480766-3-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Mounting NFS rootfs was timing out when deferred_probe_timeout was
non-zero [1]. This was because ip_auto_config() initcall times out
waiting for the network interfaces to show up when
deferred_probe_timeout was non-zero. While ip_auto_config() calls
wait_for_device_probe() to make sure any currently running deferred
probe work or asynchronous probe finishes, that wasn't sufficient to
account for devices being deferred until deferred_probe_timeout.
Commit 35a672363ab3 ("driver core: Ensure wait_for_device_probe() waits
until the deferred_probe_timeout fires") tried to fix that by making
sure wait_for_device_probe() waits for deferred_probe_timeout to expire
before returning.
However, if wait_for_device_probe() is called from the kernel_init()
context:
- Before deferred_probe_initcall() [2], it causes the boot process to
hang due to a deadlock.
- After deferred_probe_initcall() [3], it blocks kernel_init() from
continuing till deferred_probe_timeout expires and beats the point of
deferred_probe_timeout that's trying to wait for userspace to load
modules.
Neither of this is good. So revert the changes to
wait_for_device_probe().
[1] - https://lore.kernel.org/lkml/TYAPR01MB45443DF63B9EF29054F7C41FD8C60@TYAPR01MB4544.jpnprd01.prod.outlook.com/
[2] - https://lore.kernel.org/lkml/YowHNo4sBjr9ijZr@dev-arch.thelio-3990X/
[3] - https://lore.kernel.org/lkml/Yo3WvGnNk3LvLb7R@linutronix.de/
Fixes: 35a672363ab3 ("driver core: Ensure wait_for_device_probe() waits until the deferred_probe_timeout fires")
Cc: John Stultz <jstultz@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Basil Eljuse <Basil.Eljuse@arm.com>
Cc: Ferry Toth <fntoth@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Anders Roxell <anders.roxell@linaro.org>
Cc: linux-pm@vger.kernel.org
Reported-by: Nathan Chancellor <nathan@kernel.org>
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: John Stultz <jstultz@google.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220526034609.480766-2-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Rafael J. Wysocki <rafael@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / Thunderbolt updates from Greg KH:
"Here is the "big" set of USB and Thunderbolt driver changes for
5.18-rc1. For the most part it's been a quiet development cycle for
the USB core, but there are the usual "hot spots" of development
activity.
Included in here are:
- Thunderbolt driver updates:
- fixes for devices without displayport adapters
- lane bonding support and improvements
- other minor changes based on device testing
- dwc3 gadget driver changes.
It seems this driver will never be finished given that the IP core
is showing up in zillions of new devices and each implementation
decides to do something different with it...
- uvc gadget driver updates as more devices start to use and rely on
this hardware as well
- usb_maxpacket() api changes to remove an unneeded and unused
parameter.
- usb-serial driver device id updates and small cleanups
- typec cleanups and fixes based on device testing
- device tree updates for usb properties
- lots of other small fixes and driver updates.
All of these have been in linux-next for weeks with no reported
problems"
* tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits)
USB: new quirk for Dell Gen 2 devices
usb: dwc3: core: Add error log when core soft reset failed
usb: dwc3: gadget: Move null pinter check to proper place
usb: hub: Simplify error and success path in port_over_current_notify
usb: cdns3: allocate TX FIFO size according to composite EP number
usb: dwc3: Fix ep0 handling when getting reset while doing control transfer
usb: Probe EHCI, OHCI controllers asynchronously
usb: isp1760: Fix out-of-bounds array access
xhci: Don't defer primary roothub registration if there is only one roothub
USB: serial: option: add Quectel BG95 modem
USB: serial: pl2303: fix type detection for odd device
xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI
xhci: Remove quirk for over 10 year old evaluation hardware
xhci: prevent U2 link power state if Intel tier policy prevented U1
xhci: use generic command timer for stop endpoint commands.
usb: host: xhci-plat: omit shared hcd if either root hub has no ports
usb: host: xhci-plat: prepare operation w/o shared hcd
usb: host: xhci-plat: create shared hcd after having added main hcd
xhci: prepare for operation w/o shared hcd
xhci: factor out parts of xhci_gen_setup()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial driver updates from Greg KH:
"Here is the big set of tty and serial driver updates for 5.19-rc1.
Lots of tiny cleanups in here, the major stuff is:
- termbit cleanups and unification by Ilpo. A much needed change that
goes a long way to making things simpler for all of the different
arches
- tty documentation cleanups and movements to their own place in the
documentation tree
- old tty driver cleanups and fixes from Jiri to bring some existing
drivers into the modern world
- RS485 cleanups and unifications to make it easier for individual
drivers to support this mode instead of having to duplicate logic
in each driver
- Lots of 8250 driver updates and additions
- new device id additions
- n_gsm continued fixes and cleanups
- other minor serial driver updates and cleanups
All of these have been in linux-next for weeks with no reported issues"
* tag 'tty-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (166 commits)
tty: Rework receive flow control char logic
pcmcia: synclink_cs: Don't allow CS5-6
serial: stm32-usart: Correct CSIZE, bits, and parity
serial: st-asc: Sanitize CSIZE and correct PARENB for CS7
serial: sifive: Sanitize CSIZE and c_iflag
serial: sh-sci: Don't allow CS5-6
serial: txx9: Don't allow CS5-6
serial: rda-uart: Don't allow CS5-6
serial: digicolor-usart: Don't allow CS5-6
serial: uartlite: Fix BRKINT clearing
serial: cpm_uart: Fix build error without CONFIG_SERIAL_CPM_CONSOLE
serial: core: Do stop_rx in suspend path for console if console_suspend is disabled
tty: serial: qcom-geni-serial: Remove uart frequency table. Instead, find suitable frequency with call to clk_round_rate.
dt-bindings: serial: renesas,em-uart: Add RZ/V2M clock to access the registers
serial: 8250_fintek: Check SER_RS485_RTS_* only with RS485
Revert "serial: 8250_mtk: Make sure to select the right FEATURE_SEL"
serial: msm_serial: disable interrupts in __msm_console_write()
serial: meson: acquire port->lock in startup()
serial: 8250_dw: Use dev_err_probe()
serial: 8250_dw: Use devm_add_action_or_reset()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here is the big set of staging driver updates for 5.19-rc1.
Lots of forward progress happened this development cycle, one driver
(wfx wireless driver) got merged into the real portion of the kernel,
and another one (unisys) was removed as no one is around anymore to
take care of it and no one has the hardware. Combined with loads of
tiny driver cleanups overall we removed 13k lines of code from the
tree, a nice improvement.
Other than the wfx and unisys driver changes the major points of this
merge is:
- r8188eu driver cleanups. So many cleanups. It's amazing just how
many things have been cleaned up here, and yet, how many remain to
go. Lots of work happened here, and it doesn't look to slow down
any time soon.
- other wifi driver cleanups. Not as many as the r8188eu driver, but
still pretty impressive from a janitorial point of view.
- bcm2853 driver cleanups
- other very minor driver cleanups
All of these have been in the linux-next tree for weeks with no
reported issues"
* tag 'staging-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (363 commits)
staging: r8188eu: remove include/rtw_debug.h
staging: r8188eu: prevent ->Ssid overflow in rtw_wx_set_scan()
staging: r8188eu: delete rtw_wx_read/write32()
staging: r8188eu: Remove multiple assignments
staging: r8188eu: add check for kzalloc
staging: r8188eu: fix warnings in rtw_wlan_util
staging: r8188eu: fix warnings in rtw_pwrctrl
staging: r8188eu: fix warnings in rtw_p2p
staging: rtl8712: fix uninit-value in r871xu_drv_init()
staging: rtl8712: fix uninit-value in usb_read8() and friends
staging: rtl8712: add error handler in r8712_usbctrl_vendorreq()
staging: r8188eu: remove _drv_ defines from include/rtw_debug.h
staging: vc04_services: remove unused macro
staging: rtl8192u: remove null check after call container_of()
staging: rtl8192e: remove null check after call container_of()
staging: ks7010: remove null check after call container_of()
staging: r8188eu: remove HW_VAR_AC_PARAM_BE from SetHwReg8188EU()
staging: r8188eu: assoc_rsp and assoc_rsp_len are not used
staging: r8188eu: last_rx_mgnt_pkts is set but not used
staging: r8188eu: simplify error handling in recv_func_prehandle
...
|
|
Pull more block driver updates from Jens Axboe:
"A collection of stragglers that were late on sending in their changes
and just followup fixes.
- NVMe fixes pull request via Christoph:
- set controller enable bit in a separate write (Niklas Cassel)
- disable namespace identifiers for the MAXIO MAP1001 (Christoph)
- fix a comment typo (Julia Lawall)"
- MD fixes pull request via Song:
- Remove uses of bdevname (Christoph Hellwig)
- Bug fixes (Guoqing Jiang, and Xiao Ni)
- bcache fixes series (Coly)
- null_blk zoned write fix (Damien)
- nbd fixes (Yu, Zhang)
- Fix for loop partition scanning (Christoph)"
* tag 'for-5.19/drivers-2022-06-02' of git://git.kernel.dk/linux-block: (23 commits)
block: null_blk: Fix null_zone_write()
nvmet: fix typo in comment
nvme: set controller enable bit in a separate write
nvme-pci: disable namespace identifiers for the MAXIO MAP1001
bcache: avoid unnecessary soft lockup in kworker update_writeback_rate()
nbd: use pr_err to output error message
nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
nbd: fix io hung while disconnecting device
nbd: don't clear 'NBD_CMD_INFLIGHT' flag if request is not completed
nbd: fix race between nbd_alloc_config() and module removal
nbd: call genl_unregister_family() first in nbd_cleanup()
md: bcache: check the return value of kzalloc() in detached_dev_do_request()
bcache: memset on stack variables in bch_btree_check() and bch_sectors_dirty_init()
block, loop: support partitions without scanning
bcache: avoid journal no-space deadlock by reserving 1 journal bucket
bcache: remove incremental dirty sector counting for bch_sectors_dirty_init()
bcache: improve multithreaded bch_sectors_dirty_init()
bcache: improve multithreaded bch_btree_check()
md: fix double free of io_acct_set bioset
md: Don't set mddev private to NULL in raid0 pers->free
...
|
|
Pull block request execute cleanups from Jens Axboe:
"This change was advertised in the initial core block pull request, but
didn't actually make that branch as we deferred it to a post-merge
pull request to avoid a bunch of cross branch issues.
This series cleans up the block execute path quite nicely"
* tag 'for-5.19/block-exec-2022-06-02' of git://git.kernel.dk/linux-block:
blk-mq: remove the done argument to blk_execute_rq_nowait
blk-mq: avoid a mess of casts for blk_end_sync_rq
blk-mq: remove __blk_execute_rq_nowait
|
