| Age | Commit message (Collapse) | Author |
|---|
|
This patch fixed the following bug.
https://bugzilla.kernel.org/show_bug.cgi?id=43282
This is caused by a firmware bug checking (checking generic address
register provided by firmware) in runtime. The checking should be
done in address mapping time instead of runtime to avoid too much
error reporting in runtime.
Reported-by: Pawel Sikora <pluto@agmk.net>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Tested-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Otherwise, I got below build error when CONFIG_LEDS_CLASS=m.
LD init/built-in.o
drivers/built-in.o: In function `asic3_led_probe':
clkdev.c:(.devinit.text+0x4680): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `r_tpu_probe':
clkdev.c:(.devinit.text+0x4838): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `asic3_led_remove':
clkdev.c:(.devexit.text+0x564): undefined reference to `led_classdev_unregister'
drivers/built-in.o: In function `r_tpu_remove':
clkdev.c:(.devexit.text+0x5a0): undefined reference to `led_classdev_unregister'
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
Fixed a coding style issue relating to trailing
white space error found by checkpatch.pl tool in drivers/leds/led-class.c
Signed-off-by: Jeffrin Jose <ahiliation@yahoo.co.in>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
delay_off
Function led_set_software_blink() assumes that blink timer is still running,
but commit 488bc35bf40df89d37486c1826b178a2fba36ce7 introduced disabling
of blink timer before each call to led_set_software_blink().
Correct led_software_blink():
1) remove protection against reprogramming blink timer to the same values,
because it only disables blinking now,
2) remove unnecessary call to led_stop_software_blink().
Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
Add support for the AR3012 chip found on the Toshiba Sallite M840-1000-XQ.
usb-devices shows:
T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0930 ProdID=0219 Rev=00.02
S: Manufacturer=Atheros Communications
S: Product=Bluetooth USB Host Controller
S: SerialNumber=Alaska Day 2006
C: #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: Giancarlo Formicuccia <giancarlo.formicuccia@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Brown paper bag: Data valid is LSB of the ISR (status register), and NOT
of ODATA (current random data word)!
With this, rngtest is a lot happier. Before:
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 3
rngtest: FIPS 140-2 failures: 997
rngtest: FIPS 140-2(2001-10-10) Monobit: 604
rngtest: FIPS 140-2(2001-10-10) Poker: 996
rngtest: FIPS 140-2(2001-10-10) Runs: 36
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 117
rngtest: input channel speed: (min=622.371; avg=23682.481; max=28224.350)Kibitss
rngtest: FIPS tests speed: (min=12.361; avg=12.718; max=12.861)Mibits/s
rngtest: Program run time: 2331696 microsecondsx
After:
rngtest 3
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions. There is NO warr.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 999
rngtest: FIPS 140-2 failures: 1
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 1
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=777.363; avg=43588.270; max=47870.711)Kibitss
rngtest: FIPS tests speed: (min=11.943; avg=12.716; max=12.844)Mibits/s
rngtest: Program run time: 1955282 microseconds
Cc: stable@vger.kernel.org
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Reported-by: George Pontis <GPontis@z9.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Previously a 6 byte array (buf) was erroneously cast to a 8 byte long
(event_bits) on 64-bit architectures which caused a stack corruption.
Signed-off-by: Bart Westgeest <bart@elbrys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change adds support for the tilegx network driver based on the
GXIO IORPC support in the tilegx software stack, using the on-chip
mPIPE packet processing engine.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
5906 devices also need the short DMA fragment workaround. This patch
makes the necessary change.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Tested-by: Christian Kujau <lists@nerdbynature.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Calls to optional subsystems cannot be made indiscriminately.
Enclose all of the usb helper functions inside
#if IS_ENABLED(CONFIG_USB)
to fix these build errors.
(The pci helper functions are OK since there are stubs in
linux/pci.h for the called functions when PCI is not enabled.
Possibly the same could be done for the called USB functions.)
ERROR: "usb_deregister" [drivers/staging/comedi/comedi.ko] undefined!
ERROR: "usb_register_driver" [drivers/staging/comedi/comedi.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmhess@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the documentation of the Y4 and Y6 formats.
Fix a poll() issue, add support for enum_frmsizes, set the proper
parent device and fix a few compliance issues.
Tested with an actual Connectix B&W parallel port webcam, both on a
little-endian and a big-endian platform. This driver has never been
so good, doing 320x240 at 1 frame per second :-)
I know, nobody cares, but still it is cool that linux can still support
this old webcam.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Tested with a HVR-1300.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
base_addr has type resource_size_t, which may be 64 bits.
Also fix a few endian issues related to mailboxes and firmware loading.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
base_addr has type resource_size_t, which may be 64 bits on a 32-bit ppc.
Tested on my ppc board.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The frequency range of the current tuner (radio or TV) was returned
instead of the frequency range of the requested tuner (which depends
on the device node).
This bug caused the frequency range of the radio tuner to be returned
when G_TUNER was called on a video node.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The field current_norm does not have to be set for g_parm to be a valid
ioctl. Remove that check, but add a check whether this is a video node
instead as g_parm only makes sense for those nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
If g_parm is handled automatically, then set readbuffers to 2, which is the
minimum number of buffers videobuf uses.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
__lpc_handle_xmit() has two bugs :
1) It can leak skbs in case TXSTATUS_ERROR is set
2) It can wake up txqueue while no slot was freed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Roland Stigge <stigge@antcom.de>
Tested-by: Roland Stigge <stigge@antcom.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lpc_eth does a copy of transmitted skbs to DMA area, without checking
skb lengths, so can trigger buffer overflows :
memcpy(pldat->tx_buff_v + txidx * ENET_MAXF_SIZE, skb->data, len);
One way to get bigger skbs is to allow MTU changes above the 1500 limit.
Calling eth_change_mtu() in ndo_change_mtu() makes sure this cannot
happen.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Kevin Wells <kevin.wells@nxp.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
v4l-dvb-git/drivers/media/video/vino.c: In function 'vino_acquire_input':
v4l-dvb-git/drivers/media/video/vino.c:2602:18: warning: 'data_norm' may be used uninitialized in this function [-Wuninitialized]
v4l-dvb-git/drivers/media/video/vino.c: In function 'vino_set_input':
v4l-dvb-git/drivers/media/video/vino.c:2690:19: warning: 'data_norm' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
v4l-dvb-git/drivers/media/dvb/frontends/cx24110.c: In function ‘cx24110_read_ucblocks’:
v4l-dvb-git/drivers/media/dvb/frontends/cx24110.c:520:40: warning: value computed is not used [-Wunused-value]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The webcam 0458:7025 (Eye911Q) has:
- an inverted power pin,
- a sensor mi0360b which cannot be probed.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The ov534 bridge is too slow to handle the sensor accesses
requested by fast hosts giving 'sccb_reg_write failed'.
A small delay fixes the problem.
Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This fixes a regression introduced by commit f7059ea and should be
backported to all supported stable kernels which have this commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Antonio Ospite <ospite@studenti.unina.it>
CC: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Even if the best results are indeed achieved with both AGC and AWB
enabled, the webcam is capable of setting these independently, and the
user can see the difference of any of the 4 combinations of these two
boolean controls.
Removing the dependency from one another simplifies the code and gives
more control to the user.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This avoids the need for a re-alloc during init.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The (radio) audio out from the tuner (which can also demod FM radio) does not
seem to be hooked up to the msp3410 on this board in any way, so the only way
to get sound from the radio part is to make the msp3410 do the FM radio demod.
The msp3410 can handle this fine, but it is a bit weird compared to how it
is handled on other boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
the tuner
bttv_init_card2() sets btv->has_audio to a *default* value from the tvcards
array and then may update it by reading a card specific eeprom or gpio
detection.
After bttv_init_card2(), bttv_init_tuner() gets called, and it should clearly
use the updated, dynamic has_radio value from btv->has_radio, rather then
the const value in the tvcards array.
This fixes the radio not working on my Hauppauge WinTV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Before this patch the owner field of the /dev/radio# device fops was set to
the snd-tea575x-tuner module itself. Meaning that the module which was using
it could be rmmod-ed while the device is open, and then BAD things happen.
I know, as I found out the hard way :)
Note that there is no need to also somehow increase the refcount of the
snd-tea575x-tuner module itself, since any drivers using it will have
symbolic references to it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CC: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix an off-by-one error in lg216x_write_regs, causing the last element
of the lg216x init block to be ignored. Spotted by Dan Carpenter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Now query/enum_dv_timings finally work again.
The timings API patches and the core ioctl changes clearly sailed right past
each other without realizing that both needed to adapt to the other.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
rndis_check_bssid_list() originally tried to check if bssid->mac and
match_bssid are equal using compare_ether_addr() when it should use
!compare_ether_addr(). This check was added by commit
b5257c952dda24df7078c74b7b811b44c6e49206 as part of workaround for
hardware issue.
Commit 2e42e4747ea72943c21551d8a206b51a9893b1e0 that replaced
compare_ether_addr with ether_addr_equal relieved that this compare
to be inverse of what it should be.
Compare was added as response to hardware bug, where bssid-list does
not contain BSSID and other information of currently connected AP
(spec insists that device must provide this information in the list
when connected). Lack bssid-data on current connection then causes
WARN_ON somewhere in cfg80211. Workaround was to check if bssid-list
returns current bssid and if it does not, manually construct bssid
information in other ways. And this workaround worked, with inverse
check. Which must mean that when hardware is experiencing the problem,
it's actually returning empty bssid-list and this check didn't make
any difference for workaround.
However inverse check causes workaround be activated when bssid-list
returns only entry, currently connected BSSID. That does not cause
problems in itself, just slightly more inaccurate information in
scan-list.
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.
this patch is dependent on 'cfg80211: fix interface combinations'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
this patch is dependent on the patch "cfg80211: fix interface
combinations"
In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC. we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.
The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.
ath: phy0: Cannot create ADHOC interface when other
interfaces already exist.
WARNING: at net/mac80211/driver-ops.h:12
ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
Hardware name: 2842RK1
wlan2: Failed check-sdata-in-driver check, flags: 0x0
Call Trace:
[<c01361b2>] warn_slowpath_common+0x72/0xa0
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<c0136283>] warn_slowpath_fmt+0x33/0x40
[<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
[<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
[<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
[<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch fixes a regression introduced by commit
5126f2590bee412e3053de851cb07f531e4be36a:
[media] v4l2-dev: add flag to have the core lock all file operations
I forgot to add the locks to the vivi read operation.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Cc: stern@rowland.harvard.edu
Cc: gregkh@linuxfoundation.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Cc: cjb@laptop.org
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Cc: w.sang@pengutronix.de
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Update the driver to parse the new unified bus-width property introduced
in commit 7f21779 "mmc: dt: Consolidate DT bindings", instead of the legacy
support-8bit property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org>
|
|
Remove unnecessary empty function.
Signed-off-by: Hiroshi DOYU <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
|
|
Fix RQ/SRQ error CQE polling. Return error CQE to consumer for error
case which was not returned previously.
Signed-off-by: Parav Pandit <parav.pandit@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix max sge calculation for sq, rq, srq for all hardware types.
Signed-off-by: Mahesh Vardhamanaiah <mahesh.vardhamanaiah@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Fix code to read the max wqe and max rqe values from mailbox response.
Signed-off-by: Mahesh Vardhamanaiah <mahesh.vardhamanaiah@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
