| Age | Commit message (Collapse) | Author |
|---|
|
Introduce a SEND_STATUS check for writes through SPI to not mark
an unsuccessful write as successful.
Since SPI SD/MMC does not have states, after a write, the card will
just hold the line LOW until it is ready again. The driver marks the
write therefore as completed as soon as it reads something other than
all zeroes.
The driver does not distinguish from a card no longer signalling busy
and it being disconnected (and the line being pulled-up by the host).
This lead to writes being marked as successful when disconnecting
a busy card.
Now the card is ensured to be still connected by an additional CMD13,
just like non-SPI is ensured to go back to TRAN state.
While at it and since we already poll for the post-write status anyway,
we might as well check for SPIs error bits (any of them).
The disconnecting card problem is reproducable for me after continuous
write activity and randomly disconnecting, around every 20-50 tries
on SPI DS for some card.
Fixes: 7213d175e3b6f ("MMC/SD card driver learns SPI")
Cc: stable@vger.kernel.org
Signed-off-by: Christian Loehle <cloehle@hyperstone.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/76f6f5d2b35543bab3dfe438f268609c@hyperstone.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use sg and not data->sg when checking sg list elements. Else only the
first element alignment is checked.
The last element should be checked the same way, for_each_sg already set
sg to sg_next(sg).
Fixes: 46b723dd867d ("mmc: mmci: add stm32 sdmmc variant")
Cc: stable@vger.kernel.org
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Link: https://lore.kernel.org/r/20220317111944.116148-2-yann.gautier@foss.st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit bb32e1987bc55ce1db400faf47d85891da3c9b9f.
Commit 1a3ed0dc3594 ("mmc: sdhci-xenon: fix 1.8v regulator stabilization")
contains proper fix for the issue described in commit bb32e1987bc5 ("mmc:
sdhci-xenon: fix annoying 1.8V regulator warning").
Fixes: 8d876bf472db ("mmc: sdhci-xenon: wait 5ms after set 1.8V signal enable")
Cc: stable@vger.kernel.org # 1a3ed0dc3594 ("mmc: sdhci-xenon: fix 1.8v regulator stabilization")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20220318141441.32329-1-pali@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The Marvell CN10K DRAM Subsystem (DSS) performance monitor is only
present on Marvell CN10K SoCs. Hence add a dependency on ARCH_THUNDER,
to prevent asking the user about this driver when configuring a kernel
without Cavium Thunder (incl. Marvell CN10K) SoC support,
Fixes: 68fa55f0e05c ("perf/marvell: cn10k DDR perf event core ownership")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/18bfd6e1bcf67db7ea656d684a8bbb68261eeb54.1648559364.git.geert+renesas@glider.be
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The bug is here:
return cluster;
The list iterator value 'cluster' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'cluster' when found, otherwise return NULL.
Cc: stable@vger.kernel.org
Fixes: 21bdbb7102ed ("perf: add qcom l2 cache perf events driver")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220327055733.4070-1-xiam0nd.tong@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Without active_discharge_on setting, the SWITCH1 discharge enable control
is always disabled. Fix it.
Fixes: 3b15ccac161a ("regulator: Add regulator driver for ATC260x PMICs")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20220403132235.123727-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If spi_register_master() fails, we must undo a previous
mxic_spi_mem_ecc_probe() call, as already done in the remove function.
Fixes: 00360ebae483 ("spi: mxic: Add support for pipelined ECC operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/09c81f751241f6ec0bac7a48d4ec814a742e0d17.1648980664.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If rpcif_hw_init() fails, Runtime PM is left enabled.
Fixes: b04cc0d912eb80d3 ("memory: renesas-rpc-if: Add support for RZ/G2L")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1c78a1f447d019bb66b6e7787f520ae78821e2ae.1648562287.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The active_discharge_on setting was missed, so output discharge resistor
is always disabled. Fix it.
Fixes: 0555d41497de ("regulator: rtq2134: Add support for Richtek RTQ2134 SubPMIC")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20220404022514.449231-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
As per Table 130 of the wm8994 datasheet at [1], there is an off-on
delay for LDO1 and LDO2. In the wm8958 datasheet [2], I could not
find any reference to it. I could not find a wm1811 datasheet to
double-check there, but as no one has complained presumably it works
without it.
This solves the issue on Samsung Aries boards with a wm8994 where
register writes fail when the device is powered off and back-on
quickly.
[1] https://statics.cirrus.com/pubs/proDatasheet/WM8994_Rev4.6.pdf
[2] https://statics.cirrus.com/pubs/proDatasheet/WM8958_v3.5.pdf
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/CY4PR04MB056771CFB80DC447C30D5A31CB1D9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This commit corrects the printing of the IPU clock error percentage if
it is between -0.1% to -0.9%. For example, if the pixel clock requested
is 27.2 MHz but only 27.0 MHz can be achieved the deviation is -0.8%.
But the fixed point math had a flaw and calculated error of 0.2%.
Before:
Clocks: IPU 270000000Hz DI 24716667Hz Needed 27200000Hz
IPU clock can give 27000000 with divider 10, error 0.2%
Want 27200000Hz IPU 270000000Hz DI 24716667Hz using IPU, 27000000Hz
After:
Clocks: IPU 270000000Hz DI 24716667Hz Needed 27200000Hz
IPU clock can give 27000000 with divider 10, error -0.8%
Want 27200000Hz IPU 270000000Hz DI 24716667Hz using IPU, 27000000Hz
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220207151411.5009-1-mark.jonas@de.bosch.com
|
|
In dw_hdmi_imx_probe(), if error happens after dw_hdmi_probe() returns
successfully, dw_hdmi_remove() should be called where necessary as
bailout.
Fixes: c805ec7eb210 ("drm/imx: dw_hdmi-imx: move initialization into probe")
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220128091944.3831256-1-victor.liu@nxp.com
|
|
Avoid leaking the display mode variable if of_get_drm_display_mode
fails.
Fixes: 76ecd9c9fb24 ("drm/imx: parallel-display: check return code from of_get_drm_display_mode()")
Addresses-Coverity-ID: 1443943 ("Resource leak")
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220108165230.44610-1-jose.exposito89@gmail.com
|
|
As the possible failure of the allocation, kmemdup() may return NULL
pointer.
Therefore, it should be better to check the return value of kmemdup()
and return error if fails.
Fixes: dc80d7038883 ("drm/imx-ldb: Add support to drm-bridge")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20220105074729.2363657-1-jiasheng@iscas.ac.cn
|
|
Samsung' 840 EVO with the latest firmware (EXT0DB6Q) locks up with
the a message: "READ LOG DMA EXT failed, trying PIO" during boot.
Initially this was discovered because it caused a crash
with the sata_dwc_460ex controller on a WD MyBook Live DUO.
The reporter "Tice Rex" which has the unique opportunity that he
has two Samsung 840 EVO SSD! One with the older firmware "EXT0BB0Q"
which booted fine and didn't expose "READ LOG DMA EXT". But the
newer/latest firmware "EXT0DB6Q" caused the headaches.
BugLink: https://github.com/openwrt/openwrt/issues/9505
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
the driver uses libata's "tag" values from in various arrays.
Since the mentioned patch bumped the ATA_TAG_INTERNAL to 32,
the value of the SATA_DWC_QCMD_MAX needs to account for that.
Otherwise ATA_TAG_INTERNAL usage cause similar crashes like
this as reported by Tice Rex on the OpenWrt Forum and
reproduced (with symbols) here:
| BUG: Kernel NULL pointer dereference at 0x00000000
| Faulting instruction address: 0xc03ed4b8
| Oops: Kernel access of bad area, sig: 11 [#1]
| BE PAGE_SIZE=4K PowerPC 44x Platform
| CPU: 0 PID: 362 Comm: scsi_eh_1 Not tainted 5.4.163 #0
| NIP: c03ed4b8 LR: c03d27e8 CTR: c03ed36c
| REGS: cfa59950 TRAP: 0300 Not tainted (5.4.163)
| MSR: 00021000 <CE,ME> CR: 42000222 XER: 00000000
| DEAR: 00000000 ESR: 00000000
| GPR00: c03d27e8 cfa59a08 cfa55fe0 00000000 0fa46bc0 [...]
| [..]
| NIP [c03ed4b8] sata_dwc_qc_issue+0x14c/0x254
| LR [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| Call Trace:
| [cfa59a08] [c003f4e0] __cancel_work_timer+0x124/0x194 (unreliable)
| [cfa59a78] [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| [cfa59a98] [c03d2b3c] ata_exec_internal_sg+0x240/0x524
| [cfa59b08] [c03d2e98] ata_exec_internal+0x78/0xe0
| [cfa59b58] [c03d30fc] ata_read_log_page.part.38+0x1dc/0x204
| [cfa59bc8] [c03d324c] ata_identify_page_supported+0x68/0x130
| [...]
This is because sata_dwc_dma_xfer_complete() NULLs the
dma_pending's next neighbour "chan" (a *dma_chan struct) in
this '32' case right here (line ~735):
> hsdevp->dma_pending[tag] = SATA_DWC_DMA_PENDING_NONE;
Then the next time, a dma gets issued; dma_dwc_xfer_setup() passes
the NULL'd hsdevp->chan to the dmaengine_slave_config() which then
causes the crash.
With this patch, SATA_DWC_QCMD_MAX is now set to ATA_MAX_QUEUE + 1.
This avoids the OOB. But please note, there was a worthwhile discussion
on what ATA_TAG_INTERNAL and ATA_MAX_QUEUE is. And why there should not
be a "fake" 33 command-long queue size.
Ideally, the dw driver should account for the ATA_TAG_INTERNAL.
In Damien Le Moal's words: "... having looked at the driver, it
is a bigger change than just faking a 33rd "tag" that is in fact
not a command tag at all."
Fixes: 28361c403683c ("libata: add extra internal command")
Cc: stable@kernel.org # 4.18+
BugLink: https://github.com/openwrt/openwrt/issues/9505
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
When returning false, ata_sff_altstatus() does not return any status
value, resulting in a compilation warning in ata_sff_lost_interrupt()
("uninitialized symbol 'status'"). Fix this by initializing the local
variable "status" to 0.
Fixes: 03c0e84f9c1e ("ata: libata-sff: refactor ata_sff_altstatus()")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"A single revert to fix a boot regression seen when clk_put() started
dropping rate range requests. It's best to keep various systems
booting so we'll kick this out and try again next time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: Drop the rate range on clk_put()"
|
|
This reverts commit 7dabfa2bc4803eed83d6f22bd6f045495f40636b. There are
multiple reports that this breaks boot on various systems. The common
theme is that orphan clks are having rates set on them when that isn't
expected. Let's revert it out for now so that -rc1 boots.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org
|
|
Pull block driver fix from Jens Axboe:
"Got two reports on nbd spewing warnings on load now, which is a
regression from a commit that went into your tree yesterday.
Revert the problematic change for now"
* tag 'for-5.18/drivers-2022-04-02' of git://git.kernel.dk/linux-block:
Revert "nbd: fix possible overflow on 'first_minor' in nbd_dev_add()"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci fix from Bjorn Helgaas:
- Fix Hyper-V "defined but not used" build issue added during merge
window (YueHaibing)
* tag 'pci-v5.18-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: hv: Remove unused hv_set_msi_entry_from_desc()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux
Pull chrome platform updates from Benson Leung:
"cros_ec_typec:
- Check for EC device - Fix a crash when using the cros_ec_typec
driver on older hardware not capable of typec commands
- Make try power role optional
- Mux configuration reorganization series from Prashant
cros_ec_debugfs:
- Fix use after free. Thanks Tzung-bi
sensorhub:
- cros_ec_sensorhub fixup - Split trace include file
misc:
- Add new mailing list for chrome-platform development:
chrome-platform@lists.linux.dev
Now with patchwork!"
* tag 'tag-chrome-platform-for-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_ec_debugfs: detach log reader wq from devm
platform: chrome: Split trace include file
platform/chrome: cros_ec_typec: Update mux flags during partner removal
platform/chrome: cros_ec_typec: Configure muxes at start of port update
platform/chrome: cros_ec_typec: Get mux state inside configure_mux
platform/chrome: cros_ec_typec: Move mux flag checks
platform/chrome: cros_ec_typec: Check for EC device
platform/chrome: cros_ec_typec: Make try power role optional
MAINTAINERS: platform-chrome: Add new chrome-platform@lists.linux.dev list
|
|
This reverts commit 6d35d04a9e18990040e87d2bbf72689252669d54.
Both Gabriel and Borislav report that this commit casues a regression
with nbd:
sysfs: cannot create duplicate filename '/dev/block/43:0'
Revert it before 5.18-rc1 and we'll investigage this separately in
due time.
Link: https://lore.kernel.org/all/YkiJTnFOt9bTv6A2@zn.tnic/
Reported-by: Gabriel L. Somlo <somlo@cmu.edu>
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In commit 9cbadf094d9d ("net: stmmac: support max-speed device tree
property"), when DT platforms don't set "max-speed", max_speed is set to
-1; for non-DT platforms, it stays the default 0.
Prior to commit eeef2f6b9f6e ("net: stmmac: Start adding phylink support"),
the check for a valid max_speed setting was to check if it was greater
than zero. This commit got it right, but subsequent patches just checked
for non-zero, which is incorrect for DT platforms.
In commit 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
the conversion switched completely to checking for non-zero value as a
valid value, which caused 1000base-T to stop getting advertised by
default.
Instead of trying to fix all the checks, simply leave max_speed alone if
DT property parsing fails.
Fixes: 9cbadf094d9d ("net: stmmac: support max-speed device tree property")
Fixes: 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220331184832.16316-1-wens@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
32b builds with CONFIG_PHYS_ADDR_T_64BIT=y, such as i386 PAE,
raise a linker error due to a 64b division:
ld: drivers/net/ethernet/fungible/funcore/fun_dev.o: in function
`fun_dev_enable':
(.text+0xe1a): undefined reference to `__udivdi3'
The divisor in the offendinng expression is a power of 2. Change it to
use an explicit right shift.
Fixes: e1ffcc66818f ("net/fungible: Add service module for Fungible drivers")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20220401232411.313881-1-dmichail@fungible.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull block driver fixes from Jens Axboe:
"Followup block driver updates and fixes for the 5.18-rc1 merge window.
In detail:
- NVMe pull request
- Fix multipath hang when disk goes live over reconnect (Anton
Eidelman)
- fix RCU hole that allowed for endless looping in multipath
round robin (Chris Leech)
- remove redundant assignment after left shift (Colin Ian King)
- add quirks for Samsung X5 SSDs (Monish Kumar R)
- fix the read-only state for zoned namespaces with unsupposed
features (Pankaj Raghav)
- use a private workqueue instead of the system workqueue in
nvmet (Sagi Grimberg)
- allow duplicate NSIDs for private namespaces (Sungup Moon)
- expose use_threaded_interrupts read-only in sysfs (Xin Hao)"
- nbd minor allocation fix (Zhang)
- drbd fixes and maintainer addition (Lars, Jakob, Christoph)
- n64cart build fix (Jackie)
- loop compat ioctl fix (Carlos)
- misc fixes (Colin, Dongli)"
* tag 'for-5.18/drivers-2022-04-01' of git://git.kernel.dk/linux-block:
drbd: remove check of list iterator against head past the loop body
drbd: remove usage of list iterator variable after loop
nbd: fix possible overflow on 'first_minor' in nbd_dev_add()
MAINTAINERS: add drbd co-maintainer
drbd: fix potential silent data corruption
loop: fix ioctl calls using compat_loop_info
nvme-multipath: fix hang when disk goes live over reconnect
nvme: fix RCU hole that allowed for endless looping in multipath round robin
nvme: allow duplicate NSIDs for private namespaces
nvmet: remove redundant assignment after left shift
nvmet: use a private workqueue instead of the system workqueue
nvme-pci: add quirks for Samsung X5 SSDs
nvme-pci: expose use_threaded_interrupts read-only in sysfs
nvme: fix the read-only state for zoned namespaces with unsupposed features
n64cart: convert bi_disk to bi_bdev->bd_disk fix build
xen/blkfront: fix comment for need_copy
xen-blkback: remove redundant assignment to variable i
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix DM integrity shrink crash due to journal entry not being marked
unused.
- Fix DM bio polling to handle possibility that underlying device(s)
return BLK_STS_AGAIN during submission.
- Fix dm_io and dm_target_io flags race condition on Alpha.
- Add some pr_err debugging to help debug cases when DM ioctl structure
is corrupted.
* tag 'for-5.18/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix bio polling to handle possibile BLK_STS_AGAIN
dm: fix dm_io and dm_target_io flags race condition on Alpha
dm integrity: set journal entry unused when shrinking device
dm ioctl: log an error if the ioctl structure is corrupted
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
"This has a handful of new features:
- Support for CURRENT_STACK_POINTER, which enables some extra stack
debugging for HARDENED_USERCOPY.
- Support for the new SBI CPU idle extension, via cpuidle and suspend
drivers.
- Profiling has been enabled in the defconfigs.
but is mostly fixes and cleanups"
* tag 'riscv-for-linus-5.18-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (21 commits)
RISC-V: K210 defconfigs: Drop redundant MEMBARRIER=n
RISC-V: defconfig: Drop redundant SBI HVC and earlycon
Documentation: riscv: remove non-existent directory from table of contents
riscv: cpu.c: don't use kernel-doc markers for comments
RISC-V: Enable profiling by default
RISC-V: module: fix apply_r_riscv_rcv_branch_rela typo
RISC-V: Declare per cpu boot data as static
RISC-V: Fix a comment typo in riscv_of_parent_hartid()
riscv: Increase stack size under KASAN
riscv: Fix fill_callchain return value
riscv: dts: canaan: Fix SPI3 bus width
riscv: Rename "sp_in_global" to "current_stack_pointer"
riscv module: remove (NOLOAD)
RISC-V: Enable RISC-V SBI CPU Idle driver for QEMU virt machine
dt-bindings: Add common bindings for ARM and RISC-V idle states
cpuidle: Add RISC-V SBI CPU idle driver
cpuidle: Factor-out power domain related code from PSCI domain driver
RISC-V: Add SBI HSM suspend related defines
RISC-V: Add arch functions for non-retentive suspend entry/exit
RISC-V: Rename relocate() and make it global
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Vasily Gorbik:
- Add kretprobes framepointer verification and return address recovery
in stacktrace.
- Support control domain masks on custom zcrypt devices and filter
admin requests.
- Cleanup timer API usage.
- Rework absolute lowcore access helpers.
- Other various small improvements and fixes.
* tag 's390-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (26 commits)
s390/alternatives: avoid using jgnop mnemonic
s390/pci: rename get_zdev_by_bus() to zdev_from_bus()
s390/pci: improve zpci_dev reference counting
s390/smp: use physical address for SIGP_SET_PREFIX command
s390: cleanup timer API use
s390/zcrypt: fix using the correct variable for sizeof()
s390/vfio-ap: fix kernel doc and signature of group notifier functions
s390/maccess: rework absolute lowcore accessors
s390/smp: cleanup control register update routines
s390/smp: cleanup target CPU callback starting
s390/test_unwind: verify __kretprobe_trampoline is replaced
s390/unwind: avoid duplicated unwinding entries for kretprobes
s390/unwind: recover kretprobe modified return address in stacktrace
s390/kprobes: enable kretprobes framepointer verification
s390/test_unwind: extend kretprobe test
s390/ap: adjust whitespace
s390/ap: use insn format for new instructions
s390/alternatives: use insn format for new instructions
s390/alternatives: use instructions instead of byte patterns
s390/traps: improve panic message for translation-specification exception
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- grammar and formatting fixes in comments for gpio-ts4900
- correct links in gpio-ts5500
- fix a warning in doc generation for the core GPIO documentation
* tag 'gpio-fixes-for-v5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: ts5500: Fix Links to Technologic Systems web resources
gpio: Properly document parent data union
gpio: ts4900: Fix comment formatting and grammar
|
|
Expanded testing of DM's bio polling support (using more fio threads
to dm-linear ontop of null_blk) exposed the possibility for polled
bios to hang (repeatedly polling in io_uring) when null_blk responds
with BLK_STS_AGAIN (due to lack of resources):
1) io_complete_rw_iopoll() is called from blkdev_bio_end_io_async() to
notify kiocb is done, that is the completion interface between block
layer and io_uring
2) io_complete_rw_iopoll() is called from io_do_iopoll()
3) dm returns BLK_STS_AGAIN for one bio (on behalf of underlying
driver), then io_complete_rw_iopoll is called, but io_do_iopoll()
doesn't handle -EAGAIN at all (due to logic in io_rw_should_reissue)
4) reason for dm's BLK_STS_AGAIN is underlying null_blk driver ran out
of requests (easier to reproduce by setting low hw_queue_depth).
5) dm should handle BLK_STS_AGAIN for POLLED underlying IO, and may
retry in dm layer.
This fix adds REQ_POLLED specific BLK_STS_AGAIN handling to
dm_io_complete() that clears REQ_POLLED and requeues the bio to DM
using queue_io().
Fixes: b99fdcdc3636 ("dm: support bio polling")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
[snitzer: revised header, reused dm_io_complete's REQ_POLLED case]
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Early alpha processors cannot write a single byte or short; they read 8
bytes, modify the value in registers and write back 8 bytes.
This could cause race condition in the structure dm_io - if the fields
flags and io_count are modified simultaneously.
Fix this bug by using 32-bit flags if we are on Alpha and if we are
compiling for a processor that doesn't have the byte-word-extension.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Fixes: bd4a6dd241ae ("dm: reduce size of dm_io and dm_target_io structs")
[snitzer: Jens allowed this change since Mikulas owns a relevant Alpha!]
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a revert of a patch resetting extra buttons on touchpads claiming to
be buttonpads as this caused regression on certain Dell devices
- a new driver for Mediatek MT6779 keypad
- a new driver for Imagis touchscreen
- rework of Google/Chrome OS "Vivaldi" keyboard handling
- assorted driver fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (31 commits)
Revert "Input: clear BTN_RIGHT/MIDDLE on buttonpads"
Input: adi - remove redundant variable z
Input: add Imagis touchscreen driver
dt-bindings: input/touchscreen: bindings for Imagis
Input: synaptics - enable InterTouch on ThinkPad T14/P14s Gen 1 AMD
Input: stmfts - fix reference leak in stmfts_input_open
Input: add bounds checking to input_set_capability()
Input: iqs5xx - use local input_dev pointer
HID: google: modify HID device groups of eel
HID: google: Add support for vivaldi to hid-hammer
HID: google: extract Vivaldi hid feature mapping for use in hid-hammer
Input: extract ChromeOS vivaldi physmap show function
HID: google: switch to devm when registering keyboard backlight LED
Input: mt6779-keypad - fix signedness bug
Input: mt6779-keypad - add MediaTek keypad driver
dt-bindings: input: Add bindings for Mediatek matrix keypad
Input: da9063 - use devm_delayed_work_autocancel()
Input: goodix - fix race on driver unbind
Input: goodix - use input_copy_abs() helper
Input: add input_copy_abs() function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"The bulk of the patches are about replacing the uie_unsupported struct
rtc_device member by a feature bit.
Subsystem:
- remove uie_unsupported, all users have been converted to clear
RTC_FEATURE_UPDATE_INTERRUPT and provide a reason
- RTCs with an alarm with a resolution of a minute are now letting
the core handle rounding down the alarm time
- fix use-after-free on device removal
New driver:
- OP-TEE RTC PTA
Drivers:
- sun6i: Add H616 support
- cmos: Fix the AltCentury for AMD platforms
- spear: set range"
* tag 'rtc-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (56 commits)
rtc: check if __rtc_read_time was successful
rtc: gamecube: Fix refcount leak in gamecube_rtc_read_offset_from_sram
rtc: mc146818-lib: Fix the AltCentury for AMD platforms
rtc: optee: add RTC driver for OP-TEE RTC PTA
rtc: pm8xxx: Return -ENODEV if set_time disallowed
rtc: pm8xxx: Attach wake irq to device
clk: sunxi-ng: sun6i-rtc: include clk/sunxi-ng.h
rtc: remove uie_unsupported
rtc: xgene: stop using uie_unsupported
rtc: hym8563: switch to RTC_FEATURE_UPDATE_INTERRUPT
rtc: hym8563: let the core handle the alarm resolution
rtc: hym8563: switch to devm_rtc_allocate_device
rtc: efi: switch to RTC_FEATURE_UPDATE_INTERRUPT
rtc: efi: switch to devm_rtc_allocate_device
rtc: add new RTC_FEATURE_ALARM_WAKEUP_ONLY feature
rtc: spear: fix spear_rtc_read_time
rtc: spear: drop uie_unsupported
rtc: spear: set range
rtc: spear: switch to devm_rtc_allocate_device
rtc: pcf8563: switch to RTC_FEATURE_UPDATE_INTERRUPT
...
|
|
Commit f6f72f32c22c ("dm integrity: don't replay journal data past the
end of the device") skips journal replay if the target sector points
beyond the end of the device. Unfortunatelly, it doesn't set the
journal entry unused, which resulted in this BUG being triggered:
BUG_ON(!journal_entry_is_unused(je))
Fix this by calling journal_entry_set_unused() for this case.
Fixes: f6f72f32c22c ("dm integrity: don't replay journal data past the end of the device")
Cc: stable@vger.kernel.org # v5.7+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Tested-by: Milan Broz <gmazyland@gmail.com>
[snitzer: revised header]
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
This will help triage bugs when userspace is passing invalid ioctl
structure to the kernel.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
[snitzer: log errors using DMERR instead of DMWARN]
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
KS8851_MLL selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL,
so make KS8851_MLL also depend on PTP_1588_CLOCK_OPTIONAL since
'select' does not follow any dependency chains.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851_MLL [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && HAS_IOMEM [=y]
ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info':
micrel.c:(.text+0xb35): undefined reference to `ptp_clock_index'
ld: drivers/net/phy/micrel.o: in function `lan8814_probe':
micrel.c:(.text+0x2586): undefined reference to `ptp_clock_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
header_ops.create should return the length of the header,
instead mctp_i2c_head_create() returned 0.
This didn't cause any problem because the MCTP stack accepted
0 as success.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handling of all-multicast flag and associated multicast promiscuous
mode is broken in ice driver. When an user switches allmulticast
flag on or off the driver checks whether any VLANs are configured
over the interface (except default VLAN 0).
If any extra VLANs are registered it enables multicast promiscuous
mode for all these VLANs (including default VLAN 0) using
ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all
multicast packets tagged with known VLAN ID or untagged are received
and multicast packets tagged with unknown VLAN ID ignored.
If no extra VLANs are registered (so only VLAN 0 exists) it enables
multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC
look-up type. In this situation any multicast packets including
tagged ones are received.
The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:
ice_vsi_sync_fltr() {
...
if (changed_flags & IFF_ALLMULTI) {
if (netdev->flags & IFF_ALLMULTI) {
if (vsi->num_vlans > 1)
ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
} else {
if (vsi->num_vlans > 1)
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
}
}
...
}
The code above depends on value vsi->num_vlan that specifies number
of VLANs configured over the interface (including VLAN 0) and
this is problem because that value is modified in NDO callbacks
ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().
Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on
[1] In this scenario IFF_ALLMULTI is enabled and the driver calls
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs
multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this
call is effectively NOP because it looks for multicast promisc
rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such
rules exist. So the all-multicast remains enabled silently
in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call
fails (-EEXIST) because non-VLAN multicast promisc rule already
exists.
Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off
[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast
promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast
promisc rules is added for this new VLAN so the interface does
not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains
installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1
the driver tries to remove multicast promisc rule for VLAN 0
with non-VLAN look-up that does not exist.
All-multicast looks disabled from user point of view but it
is partially enabled in HW (interface receives all multicast
packets either untagged or tagged with VLAN ID 10)
To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and
ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed
and IFF_ALLMULTI is enabled an appropriate multicast promisc
rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added
so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed
so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY
bit protection to avoid races with ice_vsi_sync_fltr() that runs
in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions
to avoid them in their callers
7. Small improvements to increase readability
Fixes: 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2ccc1c1ccc671b ("ice: Remove excess error variables") merged
the usage of 'status' and 'err' variables into single one in
function ice_set_mac_address(). Unfortunately this causes
a regression when call of ice_fltr_add_mac() returns -EEXIST because
this return value does not indicate an error in this case but
value of 'err' remains to be -EEXIST till the end of the function
and is returned to caller.
Prior mentioned commit this does not happen because return value of
ice_fltr_add_mac() was stored to 'status' variable first and
if it was -EEXIST then 'err' remains to be zero.
Fix the problem by reset 'err' to zero when ice_fltr_add_mac()
returns -EEXIST.
Fixes: 2ccc1c1ccc671b ("ice: Remove excess error variables")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VSI is set as default forwarding one when promisc mode is set for
PF interface, when PF is switched to switchdev mode or when VF
driver asks to enable allmulticast or promisc mode for the VF
interface (when vf-true-promisc-support priv flag is off).
The third case is buggy because in that case VSI associated with
VF remains as default one after VF removal.
Reproducer:
1. Create VF
echo 1 > sys/class/net/ens7f0/device/sriov_numvfs
2. Enable allmulticast or promisc mode on VF
ip link set ens7f0v0 allmulticast on
ip link set ens7f0v0 promisc on
3. Delete VF
echo 0 > sys/class/net/ens7f0/device/sriov_numvfs
4. Try to enable promisc mode on PF
ip link set ens7f0 promisc on
Although it looks that promisc mode on PF is enabled the opposite
is true because ice_vsi_sync_fltr() responsible for IFF_PROMISC
handling first checks if any other VSI is set as default forwarding
one and if so the function does not do anything. At this point
it is not possible to enable promisc mode on PF without re-probe
device.
To resolve the issue this patch clear default forwarding VSI
during ice_vsi_release() when the VSI to be released is the default
one.
Fixes: 01b5e89aab49 ("ice: Add VF promiscuous support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in commit 048939088220
("vrf: add mac header for tunneled packets when sniffer is attached")
an Ethernet header was cooked for traffic originating from tunnel devices.
However, the header is added based on whether the mac_header is unset
and ignores cases where the device doesn't expose a mac header to upper
layers, such as in ip tunnels like ipip and gre.
Traffic originating from such devices still appears garbled when capturing
on the vrf device.
Fix by observing whether the original device exposes a header to upper
layers, similar to the logic done in af_packet.
In addition, skb->mac_len needs to be adjusted after adding the Ethernet
header for the skb_push/pull() surrounding dev_queue_xmit_nit() to work
on these packets.
Fixes: 048939088220 ("vrf: add mac header for tunneled packets when sniffer is attached")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After rx/tx ring buffer size is changed, kernel panic occurs when
it acts XDP_TX or XDP_REDIRECT.
When tx/rx ring buffer size is changed(ethtool -G), sfc driver
reallocates and reinitializes rx and tx queues and their buffer
(tx_queue->buffer).
But it misses reinitializing xdp queues(efx->xdp_tx_queues).
So, while it is acting XDP_TX or XDP_REDIRECT, it uses the uninitialized
tx_queue->buffer.
A new function efx_set_xdp_channels() is separated from efx_set_channels()
to handle only xdp queues.
Splat looks like:
BUG: kernel NULL pointer dereference, address: 000000000000002a
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#4] PREEMPT SMP NOPTI
RIP: 0010:efx_tx_map_chunk+0x54/0x90 [sfc]
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G D 5.17.0+ #55 e8beeee8289528f11357029357cf
Code: 48 8b 8d a8 01 00 00 48 8d 14 52 4c 8d 2c d0 44 89 e0 48 85 c9 74 0e 44 89 e2 4c 89 f6 48 80
RSP: 0018:ffff92f121e45c60 EFLAGS: 00010297
RIP: 0010:efx_tx_map_chunk+0x54/0x90 [sfc]
RAX: 0000000000000040 RBX: ffff92ea506895c0 RCX: ffffffffc0330870
RDX: 0000000000000001 RSI: 00000001139b10ce RDI: ffff92ea506895c0
RBP: ffffffffc0358a80 R08: 00000001139b110d R09: 0000000000000000
R10: 0000000000000001 R11: ffff92ea414c0088 R12: 0000000000000040
R13: 0000000000000018 R14: 00000001139b10ce R15: ffff92ea506895c0
FS: 0000000000000000(0000) GS:ffff92f121ec0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
Code: 48 8b 8d a8 01 00 00 48 8d 14 52 4c 8d 2c d0 44 89 e0 48 85 c9 74 0e 44 89 e2 4c 89 f6 48 80
CR2: 000000000000002a CR3: 00000003e6810004 CR4: 00000000007706e0
RSP: 0018:ffff92f121e85c60 EFLAGS: 00010297
PKRU: 55555554
RAX: 0000000000000040 RBX: ffff92ea50689700 RCX: ffffffffc0330870
RDX: 0000000000000001 RSI: 00000001145a90ce RDI: ffff92ea50689700
RBP: ffffffffc0358a80 R08: 00000001145a910d R09: 0000000000000000
R10: 0000000000000001 R11: ffff92ea414c0088 R12: 0000000000000040
R13: 0000000000000018 R14: 00000001145a90ce R15: ffff92ea50689700
FS: 0000000000000000(0000) GS:ffff92f121e80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000000000000002a CR3: 00000003e6810005 CR4: 00000000007706e0
PKRU: 55555554
Call Trace:
<IRQ>
efx_xdp_tx_buffers+0x12b/0x3d0 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5]
__efx_rx_packet+0x5c3/0x930 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5]
efx_rx_packet+0x28c/0x2e0 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5]
efx_ef10_ev_process+0x5f8/0xf40 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5]
? enqueue_task_fair+0x95/0x550
efx_poll+0xc4/0x360 [sfc 84c94b8e32d44d296c17e10a634d3ad454de4ba5]
Fixes: 3990a8fffbda ("sfc: allocate channels for XDP tx queues")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 37ef4c19b4c659926ce65a7ac709ceaefb211c40.
The touchpad present in the Dell Precision 7550 and 7750 laptops
reports a HID_DG_BUTTONTYPE of type MT_BUTTONTYPE_CLICKPAD. However,
the device is not a clickpad, it is a touchpad with physical buttons.
In order to fix this issue, a quirk for the device was introduced in
libinput [1] [2] to disable the INPUT_PROP_BUTTONPAD property:
[Precision 7x50 Touchpad]
MatchBus=i2c
MatchUdevType=touchpad
MatchDMIModalias=dmi:*svnDellInc.:pnPrecision7?50*
AttrInputPropDisable=INPUT_PROP_BUTTONPAD
However, because of the change introduced in 37ef4c19b4 ("Input: clear
BTN_RIGHT/MIDDLE on buttonpads") the BTN_RIGHT key bit is not mapped
anymore breaking the device right click button and making impossible to
workaround it in user space.
In order to avoid breakage on other present or future devices, revert
the patch causing the issue.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220321184404.20025-1-jose.exposito89@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Debugfs console_log uses devm memory (e.g. debug_info in
cros_ec_console_log_poll()). However, lifecycles of device and debugfs
are independent. An use-after-free issue is observed if userland
program operates the debugfs after the memory has been freed.
The call trace:
do_raw_spin_lock
_raw_spin_lock_irqsave
remove_wait_queue
ep_unregister_pollwait
ep_remove
do_epoll_ctl
A Python example to reproduce the issue:
... import select
... p = select.epoll()
... f = open('/sys/kernel/debug/cros_scp/console_log')
... p.register(f, select.POLLIN)
... p.poll(1)
[(4, 1)] # 4=fd, 1=select.POLLIN
[ shutdown cros_scp at the point ]
... p.poll(1)
[(4, 16)] # 4=fd, 16=select.POLLHUP
... p.unregister(f)
An use-after-free issue raises here. It called epoll_ctl with
EPOLL_CTL_DEL which in turn to use the workqueue in the devm (i.e.
log_wq).
Detaches log reader's workqueue from devm to make sure it is persistent
even if the device has been removed.
Signed-off-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: Guenter Roeck <groeck@google.com>
Link: https://lore.kernel.org/r/20220209051130.386175-1-tzungbi@google.com
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
cros_ec_trace.h defined 5 tracing events, 2 for cros_ec_proto and
3 for cros_ec_sensorhub_ring.
These 2 files are in different kernel modules, the traces are defined
twice in the kernel which leads to problem enabling only some traces.
Move sensorhub traces from cros_ec_trace.h to cros_ec_sensorhub_trace.h
and enable them only in cros_ec_sensorhub kernel module.
Check we can now enable any single traces: without this patch,
we can only enable all sensorhub traces or none.
Fixes: d453ceb6549a ("platform/chrome: sensorhub: Add trace events for sample")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220122001301.640337-1-gwendal@chromium.org
Signed-off-by: Benson Leung <bleung@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fixes for various memory issues
UBI:
- Fix for a race condition in cdev ioctl handler
UBIFS:
- Fixes for O_TMPFILE and whiteout handling
- Fixes for various memory issues"
* tag 'for-linus-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubifs: rename_whiteout: correct old_dir size computing
jffs2: fix memory leak in jffs2_scan_medium
jffs2: fix memory leak in jffs2_do_mount_fs
jffs2: fix use-after-free in jffs2_clear_xattr_subsystem
fs/jffs2: fix comments mentioning i_mutex
ubi: fastmap: Return error code if memory allocation fails in add_aeb()
ubifs: Fix to add refcount once page is set private
ubifs: Fix read out-of-bounds in ubifs_wbuf_write_nolock()
ubifs: setflags: Make dirtied_ino_d 8 bytes aligned
ubifs: Rectify space amount budget for mkdir/tmpfile operations
ubifs: Fix 'ui->dirty' race between do_tmpfile() and writeback work
ubifs: Rename whiteout atomically
ubifs: Add missing iput if do_tmpfile() failed in rename whiteout
ubifs: Fix wrong number of inodes locked by ui_mutex in ubifs_inode comment
ubifs: Fix deadlock in concurrent rename whiteout and inode writeback
ubifs: rename_whiteout: Fix double free for whiteout_ui->data
ubi: Fix race condition between ctrl_cdev_ioctl and ubi_cdev_ioctl
|
|
When list_for_each_entry() completes the iteration over the whole list
without breaking the loop, the iterator value will be a bogus pointer
computed based on the head element.
While it is safe to use the pointer to determine if it was computed
based on the head element, either with list_entry_is_head() or
&pos->member == head, using the iterator variable after the loop should
be avoided.
In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to point to the found element [1].
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Reviewed-by: Christoph Böhmwalder <christoph.boehmwalder@linbit.com>
Link: https://lore.kernel.org/r/20220331220349.885126-2-jakobkoschel@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to iterate through the list [1].
Since that variable should not be used past the loop iteration, a
separate variable is used to 'remember the current location within the
loop'.
To either continue iterating from that position or skip the iteration
(if the previous iteration was complete) list_prepare_entry() is used.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220331220349.885126-1-jakobkoschel@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- If a hardware random number generator passes a sufficiently large
chunk of entropy to random.c during early boot, we now skip the
"fast_init" business and let it initialize the RNG.
This makes CONFIG_RANDOM_TRUST_BOOTLOADER=y actually useful.
- We already have the command line `random.trust_cpu=0/1` option for
RDRAND, which let distros enable CONFIG_RANDOM_TRUST_CPU=y while
placating concerns of more paranoid users.
Now we add `random.trust_bootloader=0/1` so that distros can
similarly enable CONFIG_RANDOM_TRUST_BOOTLOADER=y.
- Re-add a comment that got removed by accident in the recent revert.
- Add the spec-compliant ACPI CID for vmgenid, which Microsoft added to
the vmgenid spec at Ard's request during earlier review.
- Restore build-time randomness via the latent entropy plugin, which
was lost when we transitioned to using a hash function.
* tag 'random-5.18-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: mix build-time latent entropy into pool at init
virt: vmgenid: recognize new CID added by Hyper-V
random: re-add removed comment about get_random_{u32,u64} reseeding
random: treat bootloader trust toggle the same way as cpu trust toggle
random: skip fast_init if hwrng provides large chunk of entropy
|
