| Age | Commit message (Collapse) | Author |
|---|
|
Ethernet phys normally need a 25MHz refclk input. On a lot of boards
this is done with a dedicated 25MHz crystal. But the rk3588 CRU also
provides a means for that via the refclko25m_ethX clock outputs that
can be used for that function.
The mdio bus normally probes devices on the bus at runtime, by reading
specific phy registers. This requires the phy to be running and thus
also being supplied by its reference clock.
While there exist the possibility and dt-binding to declare these
input clocks for each phy in the phy-dt-node, this is only relevant
_after_ the phy has been detected and during the drivers probe-run.
This results in a chicken-and-egg-problem. The refclks in the CRU are
running on boot of course, but phy-probing can very well happen after
clk_disable_unused has run.
In the past I tried to make clock-handling part of the mdio bus code [0]
but that wasn't very well received, due to it being specific to OF and
clocks with the consensus being that resources needed for detection
need to be enabled before.
So to make probing ethernet phys using the internal refclks possible,
make those 2 clocks critical.
[0] https://lore.kernel.org/netdev/13590315.F0gNSz5aLb@diego/T/
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Link: https://lore.kernel.org/r/20241214224820.200665-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
With the proper GATE_LINK support, we no longer need to keep the
linked clocks always on. Thus it's time to drop the CLK_IS_CRITICAL
flag for them.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-6-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Recent Rockchip SoCs have a new hardware block called Native Interface
Unit (NIU), which gates clocks to devices behind them. These clock
gates will only have a running output clock when all of the following
conditions are met:
1. the parent clock is enabled
2. the enable bit is set correctly
3. the linked clock is enabled
To handle them this code registers them as a normal gate type clock,
which takes care of condition 1 + 2. The linked clock is handled by
using runtime PM clocks. Handling it via runtime PM requires setting
up a struct device for each of these clocks with a driver attached
to use the correct runtime PM operations. Thus the complete handling
of these clocks has been moved into its own driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-5-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Move rockchip_clk_add_lookup to clk.h, so that it can be used
by sub-devices with their own driver. These might also have to
do a lookup, so rename the function to rockchip_clk_set_lookup
and add a matching rockchip_clk_get_lookup.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-4-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The proper GATE_LINK implementation will use runtime PM to handle the
linked gate clocks, which requires device context. Currently all clocks
are registered early via CLK_OF_DECLARE, which is before the kernel
knows about devices.
Moving the full clocks registration to the probe routine does not work,
since the clocks needed for timers must be registered early.
To work around this issue, most of the clock tree is registered early,
but GATE_LINK clocks are handled in the probe routine. Since the resets
are not needed early either, they have also been moved to the probe
routine.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-3-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When some clocks are registered late and some clocks are registered
early we need to make sure the late registered clocks report probe defer
until the final registration has happened.
But we do not want to keep reporting probe defer after the late
registration has happened. Also not all Rockchip SoCs have late
registered clocks and may not need to report probe defer at all.
This restructures code a bit, so that there is a new function
rockchip_clk_init_early(), which should be used for initializing the CRU
structure on SoCs making use of late initialization in addition to the
early init. These platforms should call rockchip_clk_finalize()
once all clocks have been registered.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
[added EXPORT_SYMBOL_GPL(rockchip_clk_finalize) to match the early function]
Link: https://lore.kernel.org/r/20241211165957.94922-2-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Support triggering queue reset via debugfs for an upcoming test.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add queue management API support. We need a way to reset queues
to test NAPI reordering, the queue management API provides a
handy scaffolding for that.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We'll need the code to allocate and free queues in the queue management
API, factor it out.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make nsim->rqs an array of pointers and allocate them individually
so that we can swap them out one by one.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Link the NAPI instances to their configs. This will be needed to test
that NAPI config doesn't break list ordering.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Kernel coding style expects all drivers to ignore debugfs errors.
Partially because it is purely for debugging, not for important user
interfaces. Simplify the code by dropping unnecessary probe failuring
and error message on debugfs failures, which also fixes incorrect usage
IS_ERR_OR_NULL() and Smatch warning:
drivers/soc/tegra/cbb/tegra-cbb.c:80 tegra_cbb_err_debugfs_init() warn: passing zero to 'PTR_ERR'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250104141958.115911-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use IS_ENABLED() instead of defined() for checking whether a kconfig
option is enabled.
Signed-off-by: Nitin Gote <nitin.r.gote@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250103062651.798249-2-nitin.r.gote@intel.com
|
|
For v6.9 the spi subsystem changed the terminology to host and target
devices, see commit 99769a52464d ("spi: Update the "master/slave"
terminology in documentation") for reference. Support for SAMA7G5 was
forward ported recently from an old vendor branch before that
terminology change, so naming for the new struct member is adapted to
follow the current scheme.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://patch.msgid.link/20250109094843.36014-1-ada@thorsis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The following appears in kernel log at boot:
fsl_spi b01004c0.spi: at 0x(ptrval) (irq = 51), QE mode
This is useless, so remove the display of that virtual address and
display the MMIO address instead, just like serial core does.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/8a37a960ff084dfdb9233849c00714e9317ae6a5.1736405336.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
creation
Devices with hdmi_mux, amplifier or deepslp quirks create a sysfs group
for each available feature. To accomplish this, helper create/remove
functions were called on module init, but they had the following
problems:
- Create helpers called remove helpers on failure, which in turn tried
to remove the sysfs group that failed to be created
- If group creation failed mid way, previous successfully created groups
were not cleaned up
- Module exit only removed hdmi_mux group
To improve this, drop all helpers and let the platform driver manage these
sysfs groups, while controlling visibility with their respective quirks.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250105153019.19206-6-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
parse_rgb() now takes struct color_platform instead of struct
platform_zone to support upcoming refactor.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250105153019.19206-5-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Place Lighting Control State logic next to other attributes of the same
sysfs group.
While at it, rename:
store_control_state() -> lighting_control_state_store()
show_control_state() -> lighting_control_state_show()
Replace DEVICE_ATTR() with DEVICE_ATTR_RW() and do a general style
cleanup.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250105153019.19206-4-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Module initialization fails if platform device fails to register so it's
always not NULL at exit.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250105153019.19206-3-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add the Acer Predator PT16-72 to acer_quirks to provide support
for the turbo button and predator_v4 interfaces.
Tested-by: Eric Johnsten <ejohnsten@gmail.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250107175652.3171-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
There are no users left.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-6-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The usage of the lifecycle functions is not necessary anymore.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-5-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The usage of the lifecycle functions is not necessary anymore.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-4-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The usage of the lifecycle functions is not necessary anymore.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-3-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The module core already guarantees that a module can only be unloaded
after all other modules using its symbols have been unloaded.
As it's already the responsibility of the drivers using
firmware_attributes_class to clean up their devices before unloading,
the lifetime of the firmware_attributes_class can be bound to the
lifetime of the module.
This enables the direct usage of firmware_attributes_class from the
drivers, without having to go through the lifecycle functions,
leading to simplifications for both the subsystem and its users.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-2-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The header firmware_attributes_class.h uses 'struct class'. It should
also include the necessary dependency header.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-1-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors.[1]
[1]: https://www.kernel.org/doc/html/latest/process/deprecated.html#strcpy
Signed-off-by: Nitin Joshi <nitjoshi@gmail.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250107021507.4786-1-nitjoshi@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
As Chris and Vasily reported, the attempt to support multiple AXP PMICs
in one system [1] breaks some of the battery and charging functionality
on devices with AXP PMICs. The reason is that the drivers now fail to get
the correct IIO channel for the ADC component, as the current code seems
to rely on the zero-based enumeration of the regulator devices.
A fix is possible, but not trivial, as it requires some rework in the AXP
MFD driver, which cannot be fully reviewed or tested in time for the
6.13 release.
So revert this patch for now, to avoid regressions on battery powered
devices. This patch was really only necessary for devices with two
PMICs, support for which is not mainline yet anyway, so we don't lose
any functionality.
This reverts commit e37ec32188701efa01455b9be42a392adab06ce4.
[1] https://lore.kernel.org/linux-sunxi/20241007001408.27249-4-andre.przywara@arm.com/
Reported-by: Chris Morgan <macroalpha82@gmail.com>
Closes: https://lore.kernel.org/linux-sunxi/675489c1.050a0220.8d73f.6e90@mx.google.com/
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com>
Closes: https://lore.kernel.org/linux-sunxi/CA+E=qVf8_9gn0y=mcdKXvj2PFoHT2eF+JN=CmtTNdRGaSnpgKg@mail.gmail.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250108164359.2609078-1-andre.przywara@arm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The AMD SFH driver includes APIs to export SRA sensor data. This data is
utilized by the AMD PMF driver to transmit SRA data to the PMF TA,
enabling the AMD PMF driver to implement the output actions specified by
the PMF TA.
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Link: https://lore.kernel.org/r/20241217151627.757477-3-Shyam-sundar.S-k@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add support to export device operating states, such as laptop placement,
platform types and propagate this data to AMD PMF driver for use in
actions.
To retrieve the device operating states data, SRA sensor support need to
be enabled in AMD SFH driver. So add support to enable the SRA sensor.
Also, remove explicit assignments to sensor_index enum.
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Basavaraj Natikar <basavaraj.natikar@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Link: https://lore.kernel.org/r/20241217151627.757477-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The overflow_work is using system wq to do overflow checks and updates
for PHC device timecounter, which might be overhelmed by other tasks.
But there is dedicated kthread in PTP subsystem designed for such
things. This patch changes the work queue to proper align with PTP
subsystem and to avoid overloading system work queue.
The adjfine() function acts the same way as overflow check worker,
we can postpone ptp aux worker till the next overflow period after
adjfine() was called.
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250107104812.380225-1-vadfed@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This fixes the i.MX6 and newer Meson platforms in my CI.
|
|
stmmac_rx_offset() is referenced in stmmac_main.c only,
let's move it to stmmac_main.c.
Drop the inline keyword by the way, it is better to let the compiler
to decide.
Compile tested only.
No functional change intended.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250107075448.4039925-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
of_syscon_register_regmap() was added for nodes which need a custom
regmap setup. It's not really correct for those nodes to claim they are
compatible with "syscon" as the default handling likely doesn't work in
those cases. If device_node_get_regmap() happens to be called first,
then of_syscon_register() will be called and an incorrect regmap will be
created (barring some other error). That may lead to unknown results in
the worst case. In the best case, of_syscon_register_regmap() will fail
with -EEXIST. This problem remains unless these cases drop "syscon" (an
ABI issue) or we exclude them using their specific compatible. ATM,
there is only one user: "google,gs101-pmu"
There are also cases of adding "syscon" compatible to existing nodes
after the fact in order to register the syscon. That presents a
potential DT ABI problem. Instead, if there's a kernel change needing a
syscon for a node, then it should be possible to allow the kernel to
register a syscon without a DT change. That's only possible by using
of_syscon_register_regmap() currently, but in the future we may want to
support a match list for cases which don't need a custom regmap.
With this change, the lookup functions will succeed for any node
registered by of_syscon_register_regmap() regardless of whether the node
compatible contains "syscon".
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-3-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The platform driver is dead code. It is not used by DT platforms since
commit bdb0066df96e ("mfd: syscon: Decouple syscon interface from
platform devices") which said:
For non-DT based platforms, this patch keeps syscon platform driver
structure so that syscon can be probed and such non-DT based drivers
can use syscon_regmap_lookup_by_pdev API and access regmap handles.
Once all users of "syscon_regmap_lookup_by_pdev" migrated to DT based,
we can completely remove platform driver of syscon, and keep only helper
functions to get regmap handles.
The last user of syscon_regmap_lookup_by_pdevname() was removed in 2018.
syscon_regmap_lookup_by_pdevname() was then removed in 2019, but that
commit failed to remove the rest of the platform driver.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-2-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
It is possible for multiple, simultaneous callers calling
device_node_get_regmap() with the same node to fail to find an entry in
the syscon_list. There is a period of time while the first caller is
calling of_syscon_register() that subsequent callers also fail to find
an entry in the syscon_list and then call of_syscon_register() a second
time.
Fix this by keeping the lock held until after of_syscon_register()
completes and adds the node to syscon_list. Convert the spinlock to a
mutex as many of the functions called in of_syscon_register() such as
kzalloc() and of_clk_get() may sleep.
Fixes: bdb0066df96e ("mfd: syscon: Decouple syscon interface from platform devices")
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Tested-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-1-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Link: https://lore.kernel.org/r/20241222-sysfs-const-bin_attr-led-v1-1-ecc5212a31fa@weissschuh.net
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
Add support for RTL8125BP rev.b. Its XID is 0x689. This chip supports
DASH and its dash type is "RTL_DASH_25_BP".
Signed-off-by: ChunHao Lin <hau@realtek.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/20250107064355.104711-1-hau@realtek.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
cht_wc_leds_probe() leaks memory when the second led_classdev_register()
call in the for-loop fails as it does not call the cleanup function
led_classdev_unregister() on the first device. Avoid this leak by
calling devm_led_classdev_register().
Fixes: 047da762b9a9 ("leds: Add Intel Cherry Trail Whiskey Cove PMIC LED driver")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://lore.kernel.org/r/20241220085346.533675-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
We found a timeout problem with the pldm command on our system. The
reason is that the MCTP-I3C driver has a race condition when receiving
multiple-packet messages in multi-thread, resulting in a wrong packet
order problem.
We identified this problem by adding a debug message to the
mctp_i3c_read function.
According to the MCTP spec, a multiple-packet message must be composed
in sequence, and if there is a wrong sequence, the whole message will be
discarded and wait for the next SOM.
For example, SOM → Pkt Seq #2 → Pkt Seq #1 → Pkt Seq #3 → EOM.
Therefore, we try to solve this problem by adding a mutex to the
mctp_i3c_read function. Before the modification, when a command
requesting a multiple-packet message response is sent consecutively, an
error usually occurs within 100 loops. After the mutex, it can go
through 40000 loops without any error, and it seems to run well.
Fixes: c8755b29b58e ("mctp i3c: MCTP I3C driver")
Signed-off-by: Leo Yang <Leo-Yang@quantatw.com>
Link: https://patch.msgid.link/20250107031529.3296094-1-Leo-Yang@quantatw.com
[pabeni@redhat.com: dropped already answered question from changelog]
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
LED-backlights
Add driver for TI LP8864, LP8864S, LP8866 4/6 channel LED-backlight drivers
with I2C interface.
Link: https://www.ti.com/lit/gpn/lp8864-q1
Link: https://www.ti.com/lit/gpn/lp8864s-q1
Link: https://www.ti.com/lit/gpn/lp8866-q1
Link: https://www.ti.com/lit/gpn/lp8866s-q1
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@siemens.com>
Link: https://lore.kernel.org/r/20241218210829.73191-3-alexander.sverdlin@siemens.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@remote-tech.co.uk>
Link: https://lore.kernel.org/r/20241218183401.41687-4-vicentiu.galanopulo@remote-tech.co.uk
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The temp client is used only in scope of this function, so there's no
benefit in dynamic allocation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
i2c-atr catches the BUS_NOTIFY_DEL_DEVICE event on the bus and removes
the translation by calling i2c_atr_detach_client().
However, BUS_NOTIFY_DEL_DEVICE happens when the device is about to be
removed from this bus, i.e. before removal, and thus before calling
.remove() on the driver. If the driver happens to do any i2c
transactions in its remove(), they will fail.
Fix this by catching BUS_NOTIFY_REMOVED_DEVICE instead, thus removing
the translation only after the device is actually removed.
Fixes: a076a860acae ("media: i2c: add I2C Address Translator (ATR) support")
Cc: stable@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Romain Gantois <romain.gantois@bootlin.com>
Tested-by: Romain Gantois <romain.gantois@bootlin.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
The reference count of the device incremented in device_initialize() is
not decremented when device_add() fails. Add a put_device() call before
returning from the function.
This bug was found by an experimental static analysis tool that I am
developing.
Fixes: 60f68597024d ("i2c: core: Setup i2c_adapter runtime-pm before calling device_add()")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
Use MFD_CELL macro helpers instead of plain struct properties, which makes
the code shorter with the common defined MFD cell attributes.
Signed-off-by: Shree Ramamoorthy <s-ramamoorthy@ti.com>
Link: https://lore.kernel.org/r/20241217204935.1012106-2-s-ramamoorthy@ti.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
sub-pipe PG is not present on DG1. Setting these bits can disable
other power gates and cause GPU hangs on video playbacks.
VLK: 16314, 4304
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/13381
Cc: Vinay Belgaumkar <vinay.belgaumkar@intel.com>
Cc: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241219235536.454270-1-rodrigo.vivi@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 2f12e9c029315c1400059b2e7fdf53117c09c3a9)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
If GuC fails to load, the driver wedges, but in the process it tries to
do stuff that may not be initialized yet. This moves the
xe_gt_tlb_invalidation_init() to be done earlier: as its own doc says,
it's a software-only initialization and should had been named with the
_early() suffix.
Move it to be called by xe_gt_init_early(), so the locks and seqno are
initialized, avoiding a NULL ptr deref when wedging:
xe 0000:03:00.0: [drm] *ERROR* GT0: load failed: status: Reset = 0, BootROM = 0x50, UKernel = 0x00, MIA = 0x00, Auth = 0x01
xe 0000:03:00.0: [drm] *ERROR* GT0: firmware signature verification failed
xe 0000:03:00.0: [drm] *ERROR* CRITICAL: Xe has declared device 0000:03:00.0 as wedged.
...
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] PREEMPT SMP NOPTI
CPU: 9 UID: 0 PID: 3908 Comm: modprobe Tainted: G U W 6.13.0-rc4-xe+ #3
Tainted: [U]=USER, [W]=WARN
Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-S ADP-S DDR5 UDIMM CRB, BIOS ADLSFWI1.R00.3275.A00.2207010640 07/01/2022
RIP: 0010:xe_gt_tlb_invalidation_reset+0x75/0x110 [xe]
This can be easily triggered by poking the GuC binary to force a
signature failure. There will still be an extra message,
xe 0000:03:00.0: [drm] *ERROR* GT0: GuC mmio request 0x4100: no reply 0x4100
but that's better than a NULL ptr deref.
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/3956
Fixes: c9474b726b93 ("drm/xe: Wedge the entire device")
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250103001111.331684-2-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 5001ef3af8f2c972d6fd9c5221a8457556f8bea6)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Don't populate the const read-only array touch_ring_model_params_buf on
the stack at run time, instead make it static const.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
|
