| Age | Commit message (Collapse) | Author |
|---|
|
There are spi devices with multiple frequency limitations depending on
the invoked command. We probably do not want to afford running at the
lowest supported frequency all the time, so if we want to get the most
of our hardware, we need to allow per-operation frequency limitations.
Among all the SPI memory controllers, I believe all are capable of
changing the spi frequency on the fly. Some of the drivers do not make
any frequency setup though. And some others will derive a per chip
prescaler value which will be used forever.
Actually changing the frequency on the fly is something new in Linux, so
we need to carefully flag the drivers which do and do not support it. A
controller capability is created for that, and the presence for this
capability will always be checked before accepting such pattern.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-2-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the spi subsystem, the bus frequency is derived as follows:
- the controller may expose a minimum and maximum operating frequency
- the hardware description, through the spi peripheral properties,
advise what is the maximum acceptable frequency from a device/wiring
point of view.
Transfers must be observed at a frequency which fits both (so in
practice, the lowest maximum).
Actually, this second point mixes two information and already takes the
lowest frequency among:
- what the spi device is capable of (what is written in the component
datasheet)
- what the wiring allows (electromagnetic sensibility, crossovers,
terminations, antenna effect, etc).
This logic works until spi devices are no longer capable of sustaining
their highest frequency regardless of the operation. Spi memories are
typically subject to such variation. Some devices are capable of
spitting their internally stored data (essentially in read mode) at a
very fast rate, typically up to 166MHz on Winbond SPI-NAND chips, using
"fast" commands. However, some of the low-end operations, such as
regular page read-from-cache commands, are more limited and can only be
executed at 54MHz at most. This is currently a problem in the SPI-NAND
subsystem. Another situation, even if not yet supported, will be with
DTR commands, when the data is latched on both edges of the clock. The
same chips as mentioned previously are in this case limited to
80MHz. Yet another example might be continuous reads, which, under
certain circumstances, can also run at most at 104 or 120MHz.
As a matter of fact, the "one frequency per chip" policy is outdated and
more fine grain configuration is needed: we need to allow per-operation
frequency limitations. So far, all datasheets I encountered advertise a
maximum default frequency, which need to be lowered for certain specific
operations. So based on the current infrastructure, we can still expect
firmware (device trees in general) to continued advertising the same
maximum speed which is a mix between the PCB limitations and the chip
maximum capability, and expect per-operation lower frequencies when this
is relevant.
Add a `struct spi_mem_op` member to carry this information. Not
providing this field explicitly from upper layers means that there is no
further constraint and the default spi device maximum speed will be
carried instead. The SPI_MEM_OP() macro is also expanded with an
optional frequency argument, because virtually all operations can be
subject to such a limitation, and this will allow for a smooth and
discrete transition.
For controller drivers which do not implement the spi-mem interface, the
per-transfer speed is also set acordingly to a lower (than the maximum
default) speed when relevant.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-1-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The guc_mmio_reg interface supports steering, but it is currently not
implemented. This will allow the GuC to control steering of MMIO
registers after save-restore and avoid reading from fused off MCR
register instances.
Fixes: 9c57bc08652a ("drm/xe/lnl: Drop force_probe requirement")
Signed-off-by: Jesus Narvaez <jesus.narvaez@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241212190100.3768068-1-jesus.narvaez@intel.com
|
|
Atish Patra <atishp@rivosinc.com> says:
Here are two minor improvement/fixes in the PMU event path. The first patch
was part of the series[1]. The 2nd patch was suggested during the series
review.
While the series can only be merged once SBI v3.0 is frozen, these two
patches can be independent of SBI v3.0 and can be merged sooner. Hence, these
two patches are sent as a separate series.
* b4-shazam-merge:
drivers/perf: riscv: Do not allow invalid raw event config
drivers/perf: riscv: Return error for default case
drivers/perf: riscv: Fix Platform firmware event data
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-0-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
The SBI specification allows only lower 48bits of hpmeventX to be
configured via SBI PMU. Currently, the driver masks of the higher
bits but doesn't return an error. This will lead to an additional
SBI call for config matching which should return for an invalid
event error in most of the cases.
However, if a platform(i.e Rocket and sifive cores) implements a
bitmap of all bits in the event encoding this will lead to an
incorrect event being programmed leading to user confusion.
Report the error to the user if higher bits are set during the
event mapping itself to avoid the confusion and save an additional
SBI call.
Suggested-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-3-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
If the upper two bits has an invalid valid (0x1), the event mapping
is not reliable as it returns an uninitialized variable.
Return appropriate value for the default case.
Fixes: f0c9363db2dd ("perf/riscv-sbi: Add platform specific firmware event handling")
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-2-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
Platform firmware event data field is allowed to be 62 bits for
Linux as uppper most two bits are reserved to indicate SBI fw or
platform specific firmware events.
However, the event data field is masked as per the hardware raw
event mask which is not correct.
Fix the platform firmware event data field with proper mask.
Fixes: f0c9363db2dd ("perf/riscv-sbi: Add platform specific firmware event handling")
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Link: https://lore.kernel.org/r/20241212-pmu_event_fixes_v2-v2-1-813e8a4f5962@rivosinc.com
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
device_init_wakeup() second argument is a bool type. Use proper boolean
values when calling it to match the type and to produce unambiguous code
which is easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20241217071331.3607-2-wsa+renesas@sang-engineering.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Merely enabling compile-testing should not enable additional
functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/7b8eefe3b0150101ba01c3ea55e45aa3134059ba.1733243007.git.geert+renesas@glider.be
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Fix all typos in files of xe, reported by codespell tool.
Signed-off-by: Nitin Gote <nitin.r.gote@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Stuart Summers <stuart.summers@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250106102646.1400146-2-nitin.r.gote@intel.com
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
|
|
Previously, the regulator core resolved its supply only from the parent
device or its children, ignoring the of_node specified in the
regulator_config structure.
This behavior causes issues in scenarios where multiple regulator devices
are registered for components described as children of a controller, each
with their own specific regulator supply.
For instance, in a PSE controller with multiple PIs (Power Interfaces),
each PI may have a distinct regulator supply. However, the regulator core
would incorrectly use the PSE controller node or its first child to look up
the regulator supply, rather than the node specified by the
regulator_config->of_node for the PI.
This update modifies the behavior to prioritize the of_node in
regulator_config for resolving the supply. This ensures correct resolution
of the power supply for each device. If no supply is found in the provided
of_node, the core falls back to searching within the parent device as
before.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20250109-b4-feature_poe_arrange-v2-13-55ded947b510@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When cmd_alloc_index(), fails cmd_work_handler() needs
to complete ent->slotted before returning early.
Otherwise the task which issued the command may hang:
mlx5_core 0000:01:00.0: cmd_work_handler:877:(pid 3880418): failed to allocate command entry
INFO: task kworker/13:2:4055883 blocked for more than 120 seconds.
Not tainted 4.19.90-25.44.v2101.ky10.aarch64 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/13:2 D 0 4055883 2 0x00000228
Workqueue: events mlx5e_tx_dim_work [mlx5_core]
Call trace:
__switch_to+0xe8/0x150
__schedule+0x2a8/0x9b8
schedule+0x2c/0x88
schedule_timeout+0x204/0x478
wait_for_common+0x154/0x250
wait_for_completion+0x28/0x38
cmd_exec+0x7a0/0xa00 [mlx5_core]
mlx5_cmd_exec+0x54/0x80 [mlx5_core]
mlx5_core_modify_cq+0x6c/0x80 [mlx5_core]
mlx5_core_modify_cq_moderation+0xa0/0xb8 [mlx5_core]
mlx5e_tx_dim_work+0x54/0x68 [mlx5_core]
process_one_work+0x1b0/0x448
worker_thread+0x54/0x468
kthread+0x134/0x138
ret_from_fork+0x10/0x18
Fixes: 485d65e13571 ("net/mlx5: Add a timeout to acquire the command queue semaphore")
Signed-off-by: Chenguang Zhao <zhaochenguang@kylinos.cn>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250108030009.68520-1-zhaochenguang@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pci_irq_vector() function never returns zero. It returns negative
error codes or a positive non-zero IRQ number. Fix the error checking to
test for negatives.
Fixes: a36e9f5cfe9e ("rtase: Add support for a pci table in this module")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://patch.msgid.link/f2ecc88d-af13-4651-9820-7cc665230019@stanley.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Nvidia's Tegra MGBE controllers require the IOMMU "Stream ID" (SID) to be
written to the MGBE_WRAP_AXI_ASID0_CTRL register.
The current driver is hard coded to use MGBE0's SID for all controllers.
This causes softirq time outs and kernel panics when using controllers
other than MGBE0.
Example dmesg errors when an ethernet cable is connected to MGBE1:
[ 116.133290] tegra-mgbe 6910000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 121.851283] tegra-mgbe 6910000.ethernet eth1: NETDEV WATCHDOG: CPU: 5: transmit queue 0 timed out 5690 ms
[ 121.851782] tegra-mgbe 6910000.ethernet eth1: Reset adapter.
[ 121.892464] tegra-mgbe 6910000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0
[ 121.905920] tegra-mgbe 6910000.ethernet eth1: PHY [stmmac-1:00] driver [Aquantia AQR113] (irq=171)
[ 121.907356] tegra-mgbe 6910000.ethernet eth1: Enabling Safety Features
[ 121.907578] tegra-mgbe 6910000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported
[ 121.908399] tegra-mgbe 6910000.ethernet eth1: registered PTP clock
[ 121.908582] tegra-mgbe 6910000.ethernet eth1: configuring for phy/10gbase-r link mode
[ 125.961292] tegra-mgbe 6910000.ethernet eth1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 181.921198] rcu: INFO: rcu_preempt detected stalls on CPUs/tasks:
[ 181.921404] rcu: 7-....: (1 GPs behind) idle=540c/1/0x4000000000000002 softirq=1748/1749 fqs=2337
[ 181.921684] rcu: (detected by 4, t=6002 jiffies, g=1357, q=1254 ncpus=8)
[ 181.921878] Sending NMI from CPU 4 to CPUs 7:
[ 181.921886] NMI backtrace for cpu 7
[ 181.922131] CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Kdump: loaded Not tainted 6.13.0-rc3+ #6
[ 181.922390] Hardware name: NVIDIA CTI Forge + Orin AGX/Jetson, BIOS 202402.1-Unknown 10/28/2024
[ 181.922658] pstate: 40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 181.922847] pc : handle_softirqs+0x98/0x368
[ 181.922978] lr : __do_softirq+0x18/0x20
[ 181.923095] sp : ffff80008003bf50
[ 181.923189] x29: ffff80008003bf50 x28: 0000000000000008 x27: 0000000000000000
[ 181.923379] x26: ffffce78ea277000 x25: 0000000000000000 x24: 0000001c61befda0
[ 181.924486] x23: 0000000060400009 x22: ffffce78e99918bc x21: ffff80008018bd70
[ 181.925568] x20: ffffce78e8bb00d8 x19: ffff80008018bc20 x18: 0000000000000000
[ 181.926655] x17: ffff318ebe7d3000 x16: ffff800080038000 x15: 0000000000000000
[ 181.931455] x14: ffff000080816680 x13: ffff318ebe7d3000 x12: 000000003464d91d
[ 181.938628] x11: 0000000000000040 x10: ffff000080165a70 x9 : ffffce78e8bb0160
[ 181.945804] x8 : ffff8000827b3160 x7 : f9157b241586f343 x6 : eeb6502a01c81c74
[ 181.953068] x5 : a4acfcdd2e8096bb x4 : ffffce78ea277340 x3 : 00000000ffffd1e1
[ 181.960329] x2 : 0000000000000101 x1 : ffffce78ea277340 x0 : ffff318ebe7d3000
[ 181.967591] Call trace:
[ 181.970043] handle_softirqs+0x98/0x368 (P)
[ 181.974240] __do_softirq+0x18/0x20
[ 181.977743] ____do_softirq+0x14/0x28
[ 181.981415] call_on_irq_stack+0x24/0x30
[ 181.985180] do_softirq_own_stack+0x20/0x30
[ 181.989379] __irq_exit_rcu+0x114/0x140
[ 181.993142] irq_exit_rcu+0x14/0x28
[ 181.996816] el1_interrupt+0x44/0xb8
[ 182.000316] el1h_64_irq_handler+0x14/0x20
[ 182.004343] el1h_64_irq+0x80/0x88
[ 182.007755] cpuidle_enter_state+0xc4/0x4a8 (P)
[ 182.012305] cpuidle_enter+0x3c/0x58
[ 182.015980] cpuidle_idle_call+0x128/0x1c0
[ 182.020005] do_idle+0xe0/0xf0
[ 182.023155] cpu_startup_entry+0x3c/0x48
[ 182.026917] secondary_start_kernel+0xdc/0x120
[ 182.031379] __secondary_switched+0x74/0x78
[ 212.971162] rcu: INFO: rcu_preempt detected expedited stalls on CPUs/tasks: { 7-.... } 6103 jiffies s: 417 root: 0x80/.
[ 212.985935] rcu: blocking rcu_node structures (internal RCU debug):
[ 212.992758] Sending NMI from CPU 0 to CPUs 7:
[ 212.998539] NMI backtrace for cpu 7
[ 213.004304] CPU: 7 UID: 0 PID: 0 Comm: swapper/7 Kdump: loaded Not tainted 6.13.0-rc3+ #6
[ 213.016116] Hardware name: NVIDIA CTI Forge + Orin AGX/Jetson, BIOS 202402.1-Unknown 10/28/2024
[ 213.030817] pstate: 40400009 (nZcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 213.040528] pc : handle_softirqs+0x98/0x368
[ 213.046563] lr : __do_softirq+0x18/0x20
[ 213.051293] sp : ffff80008003bf50
[ 213.055839] x29: ffff80008003bf50 x28: 0000000000000008 x27: 0000000000000000
[ 213.067304] x26: ffffce78ea277000 x25: 0000000000000000 x24: 0000001c61befda0
[ 213.077014] x23: 0000000060400009 x22: ffffce78e99918bc x21: ffff80008018bd70
[ 213.087339] x20: ffffce78e8bb00d8 x19: ffff80008018bc20 x18: 0000000000000000
[ 213.097313] x17: ffff318ebe7d3000 x16: ffff800080038000 x15: 0000000000000000
[ 213.107201] x14: ffff000080816680 x13: ffff318ebe7d3000 x12: 000000003464d91d
[ 213.116651] x11: 0000000000000040 x10: ffff000080165a70 x9 : ffffce78e8bb0160
[ 213.127500] x8 : ffff8000827b3160 x7 : 0a37b344852820af x6 : 3f049caedd1ff608
[ 213.138002] x5 : cff7cfdbfaf31291 x4 : ffffce78ea277340 x3 : 00000000ffffde04
[ 213.150428] x2 : 0000000000000101 x1 : ffffce78ea277340 x0 : ffff318ebe7d3000
[ 213.162063] Call trace:
[ 213.165494] handle_softirqs+0x98/0x368 (P)
[ 213.171256] __do_softirq+0x18/0x20
[ 213.177291] ____do_softirq+0x14/0x28
[ 213.182017] call_on_irq_stack+0x24/0x30
[ 213.186565] do_softirq_own_stack+0x20/0x30
[ 213.191815] __irq_exit_rcu+0x114/0x140
[ 213.196891] irq_exit_rcu+0x14/0x28
[ 213.202401] el1_interrupt+0x44/0xb8
[ 213.207741] el1h_64_irq_handler+0x14/0x20
[ 213.213519] el1h_64_irq+0x80/0x88
[ 213.217541] cpuidle_enter_state+0xc4/0x4a8 (P)
[ 213.224364] cpuidle_enter+0x3c/0x58
[ 213.228653] cpuidle_idle_call+0x128/0x1c0
[ 213.233993] do_idle+0xe0/0xf0
[ 213.237928] cpu_startup_entry+0x3c/0x48
[ 213.243791] secondary_start_kernel+0xdc/0x120
[ 213.249830] __secondary_switched+0x74/0x78
This bug has existed since the dwmac-tegra driver was added in Dec 2022
(See Fixes tag below for commit hash).
The Tegra234 SOC has 4 MGBE controllers, however Nvidia's Developer Kit
only uses MGBE0 which is why the bug was not found previously. Connect Tech
has many products that use 2 (or more) MGBE controllers.
The solution is to read the controller's SID from the existing "iommus"
device tree property. The 2nd field of the "iommus" device tree property
is the controller's SID.
Device tree snippet from tegra234.dtsi showing MGBE1's "iommus" property:
smmu_niso0: iommu@12000000 {
compatible = "nvidia,tegra234-smmu", "nvidia,smmu-500";
...
}
/* MGBE1 */
ethernet@6900000 {
compatible = "nvidia,tegra234-mgbe";
...
iommus = <&smmu_niso0 TEGRA234_SID_MGBE_VF1>;
...
}
Nvidia's arm-smmu driver reads the "iommus" property and stores the SID in
the MGBE device's "fwspec" struct. The dwmac-tegra driver can access the
SID using the tegra_dev_iommu_get_stream_id() helper function found in
linux/iommu.h.
Calling tegra_dev_iommu_get_stream_id() should not fail unless the "iommus"
property is removed from the device tree or the IOMMU is disabled.
While the Tegra234 SOC technically supports bypassing the IOMMU, it is not
supported by the current firmware, has not been tested and not recommended.
More detailed discussion with Thierry Reding from Nvidia linked below.
Fixes: d8ca113724e7 ("net: stmmac: tegra: Add MGBE support")
Link: https://lore.kernel.org/netdev/cover.1731685185.git.pnewman@connecttech.com
Signed-off-by: Parker Newman <pnewman@connecttech.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://patch.msgid.link/6fb97f32cf4accb4f7cf92846f6b60064ba0a3bd.1736284360.git.pnewman@connecttech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the Dell Precision M6800/OXD1M5, BIOS A26 06/13/2029, Linux prints the
warning below.
i801_smbus 0000:00:1f.4: Accelerometer lis3lv02d is present on SMBus but its address is unknown, skipping registration
Following the same suggestions by Wolfram Sang as for the Dell Precision
3540 [1], the accelerometer can be successfully found on I2C bus 0 at
address 0x29.
$ echo lis3lv02d 0x29 | sudo tee /sys/bus/i2c/devices/i2c-0/new_device
lis3lv02d 0x29
$ dmesg | tail -5
[1185.385204] lis3lv02d_i2c 0-0029: supply Vdd not found, using dummy regulator
[1185.385235] lis3lv02d_i2c 0-0029: supply Vdd_IO not found, using dummy regulator
[1185.399689] lis3lv02d: 8 bits 3DC sensor found
[1185.449391] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input371
[1185.449577] i2c i2c-0: new_device: Instantiated device lis3lv02d at 0x29
So, the device has that accelerometer. Add the I2C address to the
mapping list, and test it successfully on the device.
[1]: https://lore.kernel.org/linux-i2c/97708c11-ac85-fb62-2c8e-d37739ca826f@molgen.mpg.de/
Signed-off-by: Patrick Höhn <hoehnp@gmx.de>
Acked-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20240312193132.26518-1-hoehnp@gmx.de
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Since the changes in
commit f748a07a0b64 ("PCI: Remove legacy pcim_release()")
all pcim_enable_device() does is set up a callback that disables the
device from being disabled from driver detach. The function
pcim_pin_device() prevents said disabling. pcim_enable_device(),
therefore, sets up an action that is removed immediately afterwards by
pcim_pin_device().
Replace pcim_enable_device() with pci_enable_device() and remove the
unnecessary call to pcim_pin_device().
Signed-off-by: Philipp Stanner <pstanner@redhat.com>
Link: https://lore.kernel.org/r/20241121195624.144839-2-pstanner@redhat.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Ethernet phys normally need a 25MHz refclk input. On a lot of boards
this is done with a dedicated 25MHz crystal. But the rk3588 CRU also
provides a means for that via the refclko25m_ethX clock outputs that
can be used for that function.
The mdio bus normally probes devices on the bus at runtime, by reading
specific phy registers. This requires the phy to be running and thus
also being supplied by its reference clock.
While there exist the possibility and dt-binding to declare these
input clocks for each phy in the phy-dt-node, this is only relevant
_after_ the phy has been detected and during the drivers probe-run.
This results in a chicken-and-egg-problem. The refclks in the CRU are
running on boot of course, but phy-probing can very well happen after
clk_disable_unused has run.
In the past I tried to make clock-handling part of the mdio bus code [0]
but that wasn't very well received, due to it being specific to OF and
clocks with the consensus being that resources needed for detection
need to be enabled before.
So to make probing ethernet phys using the internal refclks possible,
make those 2 clocks critical.
[0] https://lore.kernel.org/netdev/13590315.F0gNSz5aLb@diego/T/
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Link: https://lore.kernel.org/r/20241214224820.200665-1-heiko@sntech.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
With the proper GATE_LINK support, we no longer need to keep the
linked clocks always on. Thus it's time to drop the CLK_IS_CRITICAL
flag for them.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-6-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Recent Rockchip SoCs have a new hardware block called Native Interface
Unit (NIU), which gates clocks to devices behind them. These clock
gates will only have a running output clock when all of the following
conditions are met:
1. the parent clock is enabled
2. the enable bit is set correctly
3. the linked clock is enabled
To handle them this code registers them as a normal gate type clock,
which takes care of condition 1 + 2. The linked clock is handled by
using runtime PM clocks. Handling it via runtime PM requires setting
up a struct device for each of these clocks with a driver attached
to use the correct runtime PM operations. Thus the complete handling
of these clocks has been moved into its own driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-5-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Move rockchip_clk_add_lookup to clk.h, so that it can be used
by sub-devices with their own driver. These might also have to
do a lookup, so rename the function to rockchip_clk_set_lookup
and add a matching rockchip_clk_get_lookup.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-4-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
The proper GATE_LINK implementation will use runtime PM to handle the
linked gate clocks, which requires device context. Currently all clocks
are registered early via CLK_OF_DECLARE, which is before the kernel
knows about devices.
Moving the full clocks registration to the probe routine does not work,
since the clocks needed for timers must be registered early.
To work around this issue, most of the clock tree is registered early,
but GATE_LINK clocks are handled in the probe routine. Since the resets
are not needed early either, they have also been moved to the probe
routine.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20241211165957.94922-3-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When some clocks are registered late and some clocks are registered
early we need to make sure the late registered clocks report probe defer
until the final registration has happened.
But we do not want to keep reporting probe defer after the late
registration has happened. Also not all Rockchip SoCs have late
registered clocks and may not need to report probe defer at all.
This restructures code a bit, so that there is a new function
rockchip_clk_init_early(), which should be used for initializing the CRU
structure on SoCs making use of late initialization in addition to the
early init. These platforms should call rockchip_clk_finalize()
once all clocks have been registered.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
[added EXPORT_SYMBOL_GPL(rockchip_clk_finalize) to match the early function]
Link: https://lore.kernel.org/r/20241211165957.94922-2-sebastian.reichel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Support triggering queue reset via debugfs for an upcoming test.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add queue management API support. We need a way to reset queues
to test NAPI reordering, the queue management API provides a
handy scaffolding for that.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We'll need the code to allocate and free queues in the queue management
API, factor it out.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Make nsim->rqs an array of pointers and allocate them individually
so that we can swap them out one by one.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Link the NAPI instances to their configs. This will be needed to test
that NAPI config doesn't break list ordering.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Kernel coding style expects all drivers to ignore debugfs errors.
Partially because it is purely for debugging, not for important user
interfaces. Simplify the code by dropping unnecessary probe failuring
and error message on debugfs failures, which also fixes incorrect usage
IS_ERR_OR_NULL() and Smatch warning:
drivers/soc/tegra/cbb/tegra-cbb.c:80 tegra_cbb_err_debugfs_init() warn: passing zero to 'PTR_ERR'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20250104141958.115911-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Use IS_ENABLED() instead of defined() for checking whether a kconfig
option is enabled.
Signed-off-by: Nitin Gote <nitin.r.gote@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250103062651.798249-2-nitin.r.gote@intel.com
|
|
For v6.9 the spi subsystem changed the terminology to host and target
devices, see commit 99769a52464d ("spi: Update the "master/slave"
terminology in documentation") for reference. Support for SAMA7G5 was
forward ported recently from an old vendor branch before that
terminology change, so naming for the new struct member is adapted to
follow the current scheme.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Link: https://patch.msgid.link/20250109094843.36014-1-ada@thorsis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The following appears in kernel log at boot:
fsl_spi b01004c0.spi: at 0x(ptrval) (irq = 51), QE mode
This is useless, so remove the display of that virtual address and
display the MMIO address instead, just like serial core does.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://patch.msgid.link/8a37a960ff084dfdb9233849c00714e9317ae6a5.1736405336.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
creation
Devices with hdmi_mux, amplifier or deepslp quirks create a sysfs group
for each available feature. To accomplish this, helper create/remove
functions were called on module init, but they had the following
problems:
- Create helpers called remove helpers on failure, which in turn tried
to remove the sysfs group that failed to be created
- If group creation failed mid way, previous successfully created groups
were not cleaned up
- Module exit only removed hdmi_mux group
To improve this, drop all helpers and let the platform driver manage these
sysfs groups, while controlling visibility with their respective quirks.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250105153019.19206-6-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
parse_rgb() now takes struct color_platform instead of struct
platform_zone to support upcoming refactor.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250105153019.19206-5-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Place Lighting Control State logic next to other attributes of the same
sysfs group.
While at it, rename:
store_control_state() -> lighting_control_state_store()
show_control_state() -> lighting_control_state_show()
Replace DEVICE_ATTR() with DEVICE_ATTR_RW() and do a general style
cleanup.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20250105153019.19206-4-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Module initialization fails if platform device fails to register so it's
always not NULL at exit.
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Kurt Borja <kuurtb@gmail.com>
Link: https://lore.kernel.org/r/20250105153019.19206-3-kuurtb@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add the Acer Predator PT16-72 to acer_quirks to provide support
for the turbo button and predator_v4 interfaces.
Tested-by: Eric Johnsten <ejohnsten@gmail.com>
Signed-off-by: Armin Wolf <W_Armin@gmx.de>
Link: https://lore.kernel.org/r/20250107175652.3171-1-W_Armin@gmx.de
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
There are no users left.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-6-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The usage of the lifecycle functions is not necessary anymore.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-5-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The usage of the lifecycle functions is not necessary anymore.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-4-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The usage of the lifecycle functions is not necessary anymore.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-3-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The module core already guarantees that a module can only be unloaded
after all other modules using its symbols have been unloaded.
As it's already the responsibility of the drivers using
firmware_attributes_class to clean up their devices before unloading,
the lifetime of the firmware_attributes_class can be bound to the
lifetime of the module.
This enables the direct usage of firmware_attributes_class from the
drivers, without having to go through the lifecycle functions,
leading to simplifications for both the subsystem and its users.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-2-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The header firmware_attributes_class.h uses 'struct class'. It should
also include the necessary dependency header.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Reviewed-by: Armin Wolf <W_Armin@gmx.de>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Tested-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250104-firmware-attributes-simplify-v1-1-949f9709e405@weissschuh.net
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
strcpy() performs no bounds checking on the destination buffer. This
could result in linear overflows beyond the end of the buffer, leading
to all kinds of misbehaviors.[1]
[1]: https://www.kernel.org/doc/html/latest/process/deprecated.html#strcpy
Signed-off-by: Nitin Joshi <nitjoshi@gmail.com>
Reviewed-by: Mark Pearson <mpearson-lenovo@squebb.ca>
Link: https://lore.kernel.org/r/20250107021507.4786-1-nitjoshi@gmail.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
As Chris and Vasily reported, the attempt to support multiple AXP PMICs
in one system [1] breaks some of the battery and charging functionality
on devices with AXP PMICs. The reason is that the drivers now fail to get
the correct IIO channel for the ADC component, as the current code seems
to rely on the zero-based enumeration of the regulator devices.
A fix is possible, but not trivial, as it requires some rework in the AXP
MFD driver, which cannot be fully reviewed or tested in time for the
6.13 release.
So revert this patch for now, to avoid regressions on battery powered
devices. This patch was really only necessary for devices with two
PMICs, support for which is not mainline yet anyway, so we don't lose
any functionality.
This reverts commit e37ec32188701efa01455b9be42a392adab06ce4.
[1] https://lore.kernel.org/linux-sunxi/20241007001408.27249-4-andre.przywara@arm.com/
Reported-by: Chris Morgan <macroalpha82@gmail.com>
Closes: https://lore.kernel.org/linux-sunxi/675489c1.050a0220.8d73f.6e90@mx.google.com/
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com>
Closes: https://lore.kernel.org/linux-sunxi/CA+E=qVf8_9gn0y=mcdKXvj2PFoHT2eF+JN=CmtTNdRGaSnpgKg@mail.gmail.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20250108164359.2609078-1-andre.przywara@arm.com
Signed-off-by: Lee Jones <lee@kernel.org>
|
|
The AMD SFH driver includes APIs to export SRA sensor data. This data is
utilized by the AMD PMF driver to transmit SRA data to the PMF TA,
enabling the AMD PMF driver to implement the output actions specified by
the PMF TA.
Co-developed-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Patil Rajesh Reddy <Patil.Reddy@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Link: https://lore.kernel.org/r/20241217151627.757477-3-Shyam-sundar.S-k@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
Add support to export device operating states, such as laptop placement,
platform types and propagate this data to AMD PMF driver for use in
actions.
To retrieve the device operating states data, SRA sensor support need to
be enabled in AMD SFH driver. So add support to enable the SRA sensor.
Also, remove explicit assignments to sensor_index enum.
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Basavaraj Natikar <basavaraj.natikar@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Link: https://lore.kernel.org/r/20241217151627.757477-2-Shyam-sundar.S-k@amd.com
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
|
|
The overflow_work is using system wq to do overflow checks and updates
for PHC device timecounter, which might be overhelmed by other tasks.
But there is dedicated kthread in PTP subsystem designed for such
things. This patch changes the work queue to proper align with PTP
subsystem and to avoid overloading system work queue.
The adjfine() function acts the same way as overflow check worker,
we can postpone ptp aux worker till the next overflow period after
adjfine() was called.
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Vadim Fedorenko <vadfed@meta.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250107104812.380225-1-vadfed@meta.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This fixes the i.MX6 and newer Meson platforms in my CI.
|
|
stmmac_rx_offset() is referenced in stmmac_main.c only,
let's move it to stmmac_main.c.
Drop the inline keyword by the way, it is better to let the compiler
to decide.
Compile tested only.
No functional change intended.
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250107075448.4039925-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
of_syscon_register_regmap() was added for nodes which need a custom
regmap setup. It's not really correct for those nodes to claim they are
compatible with "syscon" as the default handling likely doesn't work in
those cases. If device_node_get_regmap() happens to be called first,
then of_syscon_register() will be called and an incorrect regmap will be
created (barring some other error). That may lead to unknown results in
the worst case. In the best case, of_syscon_register_regmap() will fail
with -EEXIST. This problem remains unless these cases drop "syscon" (an
ABI issue) or we exclude them using their specific compatible. ATM,
there is only one user: "google,gs101-pmu"
There are also cases of adding "syscon" compatible to existing nodes
after the fact in order to register the syscon. That presents a
potential DT ABI problem. Instead, if there's a kernel change needing a
syscon for a node, then it should be possible to allow the kernel to
register a syscon without a DT change. That's only possible by using
of_syscon_register_regmap() currently, but in the future we may want to
support a match list for cases which don't need a custom regmap.
With this change, the lookup functions will succeed for any node
registered by of_syscon_register_regmap() regardless of whether the node
compatible contains "syscon".
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Tested-by: Will McVicker <willmcvicker@google.com>
Reviewed-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20241217-syscon-fixes-v2-3-4f56d750541d@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
|
