| Age | Commit message (Collapse) | Author |
|---|
|
Once we remove support for A-step, we'll be able to
clean the code back again.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
That's a bit nicer than open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When a station is asleep, the fw will set it as "asleep".
All queues that are used only by one station will be stopped by
the fw.
In pre-DQA mode this was relevant for aggregation queues. However,
in DQA mode a queue is owned by one station only, so all queues
will be stopped.
As a result, we don't expect to get filtered frames back to
mac80211 and don't have to maintain the entire pending_frames
state logic, the same way as we do in aggregations.
The correct behavior is to align DQA behavior with the aggregation
queue behaviour pre-DQA:
- Don't count pending frames.
- Let mac80211 know we have frames in these queues so that it can
properly handle trigger frames.
When a trigger frame is received, mac80211 tells the driver to send
frames from the queues using release_buffered_frames.
The driver will tell the fw to let frames out even if the station
is asleep. This is done by iwl_mvm_sta_modify_sleep_tx_count.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't need to print so much data in the kernel log.
Limit the data to be printed to the queue that actually
got stuck in case of a TFD queue hang, and stop dumping
all the CSR and FH registers. Over the course of time, the
CSR and FH values haven't proven themselves to be really
useful for debugging, and they are now in the firmware dump
anyway.
This comes as a preparation to the addition of more data
required to be printed by the firwmare team.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When receiving a frame, we currently pull in sizeof(*hdr) plus
some extra (crypto/snap), which is too much, most headers aren't
actually sizeof(*hdr) since that takes into account the 4-address
format but doesn't take into account QoS. As a result, a typical
frame will have 4 bytes of the payload in the SKB header already.
Fix this by calculating the correct header length, and now that
we have that, align the end of the SKB header to a multiple of 4
so that the IP header will be aligned properly when pulled in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Final API has a reserved field - adjust accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
One of the RF modules we support has been deprecated and never
released publicly. Remove support for this module.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This will allow to print the name of the commands in the
logs when we sent it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If the supported firmware versions are not found, we currently only
print "no suitable firmware found". This is not very informative for
the user trying to find the correct version to use. Improve this by
printing the exact firmware name(s) the driver supports and pointing
to the git repository where they can be found.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Only call synchronize_rcu_expedited after unlocking struct_mutex to
avoid deadlock because the workqueues depend on struct_mutex.
>From original patch by Andrea:
synchronize_rcu/synchronize_sched/synchronize_rcu_expedited() will
hang until its own workqueues are run. The i915 gem workqueues will
wait on the struct_mutex to be released. So we cannot wait for a
quiescent state using those rcu primitives while holding the
struct_mutex or it creates a circular lock dependency resulting in
kernel hangs (which is reproducible but goes undetected by lockdep).
kswapd0 D 0 700 2 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? _synchronize_rcu_expedited.constprop.65+0x2ef/0x300
? wake_up_bit+0x20/0x20
? rcu_stall_kick_kthreads.part.54+0xc0/0xc0
? rcu_exp_wait_wake+0x530/0x530
? i915_gem_shrink+0x34b/0x4b0
? i915_gem_shrinker_scan+0x7c/0x90
? i915_gem_shrinker_scan+0x7c/0x90
? shrink_slab.part.61.constprop.72+0x1c1/0x3a0
? shrink_zone+0x154/0x160
? kswapd+0x40a/0x720
? kthread+0xf4/0x130
? try_to_free_pages+0x450/0x450
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30
plasmashell D 0 4657 4614 0x00000000
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? i915_gem_close_object+0x26/0xc0
? i915_gem_close_object+0x26/0xc0
? drm_gem_object_release_handle+0x48/0x90
? drm_gem_handle_delete+0x50/0x80
? drm_ioctl+0x1fa/0x420
? drm_gem_handle_create+0x40/0x40
? pipe_write+0x391/0x410
? __vfs_write+0xc6/0x120
? do_vfs_ioctl+0x8b/0x5d0
? SyS_ioctl+0x3b/0x70
? entry_SYSCALL_64_fastpath+0x13/0x94
kworker/0:0 D 0 29186 2 0x00000000
Workqueue: events __i915_gem_free_work
Call Trace:
? __schedule+0x1a5/0x660
? schedule+0x36/0x80
? schedule_preempt_disabled+0xe/0x10
? __mutex_lock.isra.4+0x1c9/0x790
? del_timer_sync+0x44/0x50
? update_curr+0x57/0x110
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_objects+0x31/0x300
? __i915_gem_free_work+0x2d/0x40
? process_one_work+0x13a/0x3b0
? worker_thread+0x4a/0x460
? kthread+0xf4/0x130
? process_one_work+0x3b0/0x3b0
? kthread_create_on_node+0x40/0x40
? ret_from_fork+0x23/0x30
Fixes: 3d3d18f086cd ("drm/i915: Avoid rcu_barrier() from reclaim paths (shrinker)")
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 8f612d055183545070ca1009ac2eb1f2e044cc20)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
i915 is currently doing a full GPU reset at the end of
i915_gem_suspend() followed by GuC suspend in i915_drm_suspend(). This
GPU reset clobbers the GuC, causing the suspend request to then fail,
leaving the GuC in an undefined state. We need to tell the GuC to
suspend before we do the direct intel_gpu_reset().
v2: Commit message update. (Chris, Daniele)
Fixes: 1c777c5d1dcd ("drm/i915/hsw: Fix GPU hang during resume from S3-devices state")
Cc: Jeff McGee <jeff.mcgee@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1491387710-20553-1-git-send-email-sagar.a.kamble@intel.com
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit fd08923384385400101c71ac0d21d37d6b23b00d)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
For a000 devices the binding API needs to include relevant
lmac ID - support the new API.
The new API should be used regardless if the device had CDB or
not. If there is no actual CDB support the binding is bound
to first lmac regardless of the band.
There are some functionality changes in binding restrictions
and quota allocations that will be handled in future patches.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
drm-intel-fixes
gvt-fixes-2017-04-07
- execlist csb initial read ptr fix (Min)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170407084240.4d2ig5ja2umcnsq3@zhen-hp.sh.intel.com
|
|
This reverts commit 279967a65b320d174a507498aea7d44db3fee7f4.
Multiple regressions [1] [2] [3] have been reported. The hid-rmi
support would have to fixed and redone in 4.11+.
[1] http://lkml.kernel.org/r/b79b88c8-770a-13f6-5668-c3a94254e5e0@gmail.com
[2] http://lkml.kernel.org/r/375e67b5-2cb8-3491-1d71-d8650d6e9451@gmail.com
[3] https://bugzilla.kernel.org/show_bug.cgi?id=195287
Reported-by: Cameron Gutman <aicommander@gmail.com>
Reported-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reported-by: Lorenzo J. Lucchini <ljlbox@tiscali.it>
Reported-by: Thorsten Leemhuis <linux@leemhuis.info>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add bi-directional and output-enable pin configuration properties.
bi-directional allows to specify when a pin shall operate in input and
output mode at the same time. This is particularly useful in platforms
where input and output buffers have to be manually enabled.
output-enable is just syntactic sugar to specify that a pin shall
operate in output mode, ignoring the provided argument.
This pairs with input-enable pin configuration option.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
After commit 47c950d10202 ("pinctrl: cherryview: Do not add all
southwest and north GPIOs to IRQ domain") the driver does not add all
GPIOs to the irqdomain. The reason for that is that those GPIOs cannot
generate IRQs at all, only GPEs (General Purpose Events). This causes
Linux virtual IRQ numbering to change.
However, it seems some CYAN Chromebooks, including Acer Chromebook
hardcodes these Linux IRQ numbers in the ACPI tables of the machine.
Since the numbering is different now, the IRQ meant for keyboard does
not match the Linux virtual IRQ number anymore making the keyboard
non-functional.
Work this around by adding special quirk just for these machines where
we add back all GPIOs to the irqdomain. Rest of the Cherryview/Braswell
based machines will not be affected by the change.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 47c950d10202 ("pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain")
Reported-by: Adam S Levy <theadamlevy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Three video input signals suffered from a search/replace failure in
some copied code.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
current_restore_flags()
It is not safe for one thread to modify the ->flags
of another thread as there is no locking that can protect
the update.
So tsk_restore_flags(), which takes a task pointer and modifies
the flags, is an invitation to do the wrong thing.
All current users pass "current" as the task, so no developers have
accepted that invitation. It would be best to ensure it remains
that way.
So rename tsk_restore_flags() to current_restore_flags() and don't
pass in a task_struct pointer. Always operate on current->flags.
Signed-off-by: NeilBrown <neilb@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
There's a conflict between ongoing level-5 paging support and
the E820 rewrite. Since the E820 rewrite is essentially ready,
merge it into x86/mm to reduce tree conflicts.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The E820 rework in WIP.x86/boot has gone through a couple of weeks
of exposure in -tip, merge it in a wider fashion.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Cc: stable@vger.kernel.org
Signed-off-by: Cameron Gutman <aicommander@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The following warning results from holding a lane spinlock,
preempt_disable(), or the btt map spinlock and then trying to take the
reconfig_mutex to walk the poison list and potentially add new entries.
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:747
in_atomic(): 1, irqs_disabled(): 0, pid: 17159, name: dd
[..]
Call Trace:
dump_stack+0x85/0xc8
___might_sleep+0x184/0x250
__might_sleep+0x4a/0x90
__mutex_lock+0x58/0x9b0
? nvdimm_bus_lock+0x21/0x30 [libnvdimm]
? __nvdimm_bus_badblocks_clear+0x2f/0x60 [libnvdimm]
? acpi_nfit_forget_poison+0x79/0x80 [nfit]
? _raw_spin_unlock+0x27/0x40
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
nsio_rw_bytes+0x164/0x270 [libnvdimm]
btt_write_pg+0x1de/0x3e0 [nd_btt]
? blk_queue_enter+0x30/0x290
btt_make_request+0x11a/0x310 [nd_btt]
? blk_queue_enter+0xb7/0x290
? blk_queue_enter+0x30/0x290
generic_make_request+0x118/0x3b0
As a minimal fix, disable error clearing when the BTT is enabled for the
namespace. For the final fix a larger rework of the poison list locking
is needed.
Note that this is not a problem in the blk case since that path never
calls nvdimm_clear_poison().
Cc: <stable@vger.kernel.org>
Fixes: 82bf1037f2ca ("libnvdimm: check and clear poison before writing to pmem")
Cc: Dave Jiang <dave.jiang@intel.com>
[jeff: dynamically disable error clearing in the btt case]
Suggested-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Holding the reconfig_mutex over a potential userspace fault sets up a
lockdep dependency chain between filesystem-DAX and the libnvdimm ioctl
path. Move the user access outside of the lock.
[ INFO: possible circular locking dependency detected ]
4.11.0-rc3+ #13 Tainted: G W O
-------------------------------------------------------
fallocate/16656 is trying to acquire lock:
(&nvdimm_bus->reconfig_mutex){+.+.+.}, at: [<ffffffffa00080b1>] nvdimm_bus_lock+0x21/0x30 [libnvdimm]
but task is already holding lock:
(jbd2_handle){++++..}, at: [<ffffffff813b4944>] start_this_handle+0x104/0x460
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (jbd2_handle){++++..}:
lock_acquire+0xbd/0x200
start_this_handle+0x16a/0x460
jbd2__journal_start+0xe9/0x2d0
__ext4_journal_start_sb+0x89/0x1c0
ext4_dirty_inode+0x32/0x70
__mark_inode_dirty+0x235/0x670
generic_update_time+0x87/0xd0
touch_atime+0xa9/0xd0
ext4_file_mmap+0x90/0xb0
mmap_region+0x370/0x5b0
do_mmap+0x415/0x4f0
vm_mmap_pgoff+0xd7/0x120
SyS_mmap_pgoff+0x1c5/0x290
SyS_mmap+0x22/0x30
entry_SYSCALL_64_fastpath+0x1f/0xc2
-> #1 (&mm->mmap_sem){++++++}:
lock_acquire+0xbd/0x200
__might_fault+0x70/0xa0
__nd_ioctl+0x683/0x720 [libnvdimm]
nvdimm_ioctl+0x8b/0xe0 [libnvdimm]
do_vfs_ioctl+0xa8/0x740
SyS_ioctl+0x79/0x90
do_syscall_64+0x6c/0x200
return_from_SYSCALL_64+0x0/0x7a
-> #0 (&nvdimm_bus->reconfig_mutex){+.+.+.}:
__lock_acquire+0x16b6/0x1730
lock_acquire+0xbd/0x200
__mutex_lock+0x88/0x9b0
mutex_lock_nested+0x1b/0x20
nvdimm_bus_lock+0x21/0x30 [libnvdimm]
nvdimm_forget_poison+0x25/0x50 [libnvdimm]
nvdimm_clear_poison+0x106/0x140 [libnvdimm]
pmem_do_bvec+0x1c2/0x2b0 [nd_pmem]
pmem_make_request+0xf9/0x270 [nd_pmem]
generic_make_request+0x118/0x3b0
submit_bio+0x75/0x150
Cc: <stable@vger.kernel.org>
Fixes: 62232e45f4a2 ("libnvdimm: control (ioctl) messages for nvdimm_bus and nvdimm devices")
Cc: Dave Jiang <dave.jiang@intel.com>
Reported-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit 57e5568fda27 ("sata_via: Implement hotplug for VT6421") adds
hotplug IRQ handler for VT6421 but enables hotplug on all chips. This
is a bug because it causes "irq xx: nobody cared" error on VT6420 when
hot-(un)plugging a drive:
[ 381.839948] irq 20: nobody cared (try booting with the "irqpoll" option)
[ 381.840014] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc5+ #148
[ 381.840066] Hardware name: P4VM800/P4VM800, BIOS P1.60 05/29/2006
[ 381.840117] Call Trace:
[ 381.840167] <IRQ>
[ 381.840225] ? dump_stack+0x44/0x58
[ 381.840278] ? __report_bad_irq+0x14/0x97
[ 381.840327] ? handle_edge_irq+0xa5/0xa5
[ 381.840376] ? note_interrupt+0x155/0x1cf
[ 381.840426] ? handle_edge_irq+0xa5/0xa5
[ 381.840474] ? handle_irq_event_percpu+0x32/0x38
[ 381.840524] ? handle_irq_event+0x1f/0x38
[ 381.840573] ? handle_fasteoi_irq+0x69/0xb8
[ 381.840625] ? handle_irq+0x4f/0x5d
[ 381.840672] </IRQ>
[ 381.840726] ? do_IRQ+0x2e/0x8b
[ 381.840782] ? common_interrupt+0x2c/0x34
[ 381.840836] ? mwait_idle+0x60/0x82
[ 381.840892] ? arch_cpu_idle+0x6/0x7
[ 381.840949] ? do_idle+0x96/0x18e
[ 381.841002] ? cpu_startup_entry+0x16/0x1a
[ 381.841057] ? start_kernel+0x319/0x31c
[ 381.841111] ? startup_32_smp+0x166/0x168
[ 381.841165] handlers:
[ 381.841219] [<c12a7263>] ata_bmdma_interrupt
[ 381.841274] Disabling IRQ #20
Seems that VT6420 can do hotplug too (there's no documentation) but the
comments say that SCR register access (required for detecting hotplug
events) can cause problems on these chips.
For now, just keep hotplug disabled on anything other than VT6421.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
virtio-pci registers a per-vq affinity hint when using MSIX,
but fails to remove it when freeing the interrupt, resulting
in this type of splat:
[ 31.111202] WARNING: CPU: 0 PID: 2823 at kernel/irq/manage.c:1503 __free_irq+0x2c4/0x2c8
[ 31.114689] Modules linked in:
[ 31.116101] CPU: 0 PID: 2823 Comm: kexec Not tainted 4.10.0+ #6941
[ 31.118911] Hardware name: Generic DT based system
[ 31.121319] [<c022fb78>] (unwind_backtrace) from [<c0229d8c>] (show_stack+0x18/0x1c)
[ 31.125017] [<c0229d8c>] (show_stack) from [<c05192f4>] (dump_stack+0x84/0x98)
[ 31.128427] [<c05192f4>] (dump_stack) from [<c023d940>] (__warn+0xf4/0x10c)
[ 31.131910] [<c023d940>] (__warn) from [<c023da20>] (warn_slowpath_null+0x28/0x30)
[ 31.135543] [<c023da20>] (warn_slowpath_null) from [<c0290238>] (__free_irq+0x2c4/0x2c8)
[ 31.139355] [<c0290238>] (__free_irq) from [<c02902d0>] (free_irq+0x44/0x78)
[ 31.142909] [<c02902d0>] (free_irq) from [<c059d3a8>] (vp_del_vqs+0x68/0x1c0)
[ 31.146299] [<c059d3a8>] (vp_del_vqs) from [<c056ca4c>] (pci_device_shutdown+0x3c/0x78)
The obvious fix is to drop the affinity hint before freeing the
interrupt.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 5c34d002dcc7a6dd665a19d098b4f4cd5501ba1a.
Conflicts:
drivers/virtio/virtio_pci_common.c
The cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
This reverts the cleanup changes but keeps the affinity support.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 07ec51480b5eb1233f8c1b0f5d7a7c8d1247c507.
Conflicts:
drivers/virtio/virtio_pci_common.c
Unfortunately the idea does not work with threadirqs
as more than 32 queues can then map to a single interrupts.
Further, the cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
This reverts the cleanup changes but keeps the affinity support.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 53a020c661741f3b87ad3ac6fa545088aaebac9b.
The cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit 52a61516125fa9a21b3bdf4f90928308e2e5573f.
Conflicts:
drivers/virtio/virtio_pci_common.c
The cleanup seems to be one of the changes that broke
hybernation for some users. We are still not sure why
but revert helps.
This reverts the cleanup changes but keeps the affinity support.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This reverts commit de85ec8b07f82c8c84de7687f769e74bf4c26a1e.
Follow-up patches will revert 07ec51480b5e ("virtio_pci: use shared
interrupts for virtqueues") that triggered the problem so no need for
this one anymore.
Tested-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports.
The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer
inputs.
The device driver matches on the device tree node. The configuration
values are read from the device tree and written to the respective
registers.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value (ranging from 0 to 100 percent) and read
the fan tach rpm value.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Directly access the fields when needed. The accessors add clutter
not clarity and in some cases cause unnecessary read-modify-write
type access on the slow (uncached) descriptor memory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add NETIF_F_SG and create multiple TX ring entries for skb fragments.
On reclaim, the skb is only freed on the segment marked as "last".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Those are non-cachable stores, let's avoid those we don't need. Remove
the helper, it's not particularly helpful and since it uses "priv"
I can't move it to the header file.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves the packet freeing to a separate function
which is also used by ftgmac100_free_buffers() and will
be used more in the error path of fragmented sends.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We'll use variants of this accessor without barriers when
building series of descriptors for fragmented sends
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have a private lock which isn't terribly useful, and we maintain
a "tx_pending" counter for information that's already available
via a trivial arithmetic operation. Then we unconditionaly wake
the queue even when not stopped. Finally our code in tx isn't
really safe vs. a concurrent reclaim. The aspeed chips aren't SMP
today but I prefer the code being right and future proof.
So rip that out and replace it with more "standard" queue handling,
currently with a threshold of 1 queue element, which will be
increased when we implement fragmented sends.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than in the descriptor. The descriptor is mapped non-cachable
and rather slow to access.
Since to do that we need to keep track of the tx "pointer" we also
have no use of all the accesors to manipulate it, just open code
it, it's as clear and will help when adding fragmented sends.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than just transmitting garbage past the end of the small
packet.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a simple goto to a drop path at the tail of the function,
it will be used in a few more cases soon
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This will make subsequent rework of the tx path simpler
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move it below ftgmac100_xmit() and the rest of the tx path
No code change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have a reset task to reset our chip, use it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1abf71e moved the creation of new_smi->dev to earlier in the init
sequence in order to provide infrastructure for log printing.
However, the init_name was created with a hard-coded value of zero. This
presents a problem in systems with more than one interface, producing a
call trace in dmesg.
To correct the problem, simply use smi_num instead of the hard-coded
value of zero.
Tested on a lenovo x3950.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
There was actually a more general problem, the platform device wasn't
being set correctly, either, and there was a possible (though extremely
unlikely) race on smi_num. Add locks to clean up the race and use the
proper value for the platform device, too.
Tested on qemu in various configurations.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a number of bugs in the caam driver:
- device creation fails after release
- error-path NULL-pointer dereference
- spurious hardware error in RNG deinstantiation"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: caam - fix RNG deinstantiation error checking
crypto: caam - fix invalid dereference in caam_rsa_init_tfm()
crypto: caam - fix JR platform device subsequent (re)creations
|
|
Change them to have the edac_ prefix.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Move the remaining functionality to edac_mc.c. Convert "edac_report=" to
a module parameter.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Remove the old URLs.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
