| Age | Commit message (Collapse) | Author |
|---|
|
A control transfer that stopped at the status stage incorrectly
warned about a "unexpected TRB Type 4", and did not set the
transferred actual_length for the URB.
The URB actual_length for control transfers should contain the
bytes transferred in the data stage.
Bytes of a partially sent setup stage and missing bytes from
status stage should be left out.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Shutdown should be called for xhci_plat devices especially for
situations where kexec might be used by stopping DMA
transactions.
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a delay to Rx queue disables to accommodate HW needs.
v2: Added missing check for disable only, additional details on the
need for the ugly delay and fixed spacing on comment.
Change-ID: I2864ca667ce5dcc2cc44f8718113b719742a46a1
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch changes the way we handle the maximum frame size for the Rx
path. Previously we were rounding up to 2K for a 1500 MTU and then brining
the max frame size down to MTU plus a fixed amount. With this patch
applied what we now do is limit the maximum frame to 1.5K minus the value
for NET_IP_ALIGN for standard MTU, and for any MTU greater than 1500 we
allow up to the maximum frame size. This makes the behavior more
consistent with the other drivers such as igb which had similar logic. In
addition it reduces the test matrix for MTU since we only have two max
frame sizes that are handled for Rx now.
Change-ID: I23a9d3c857e7df04b0ef28c64df63e659c013f3f
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds a control which will allow us to toggle into and out of the
legacy Rx mode. The legacy Rx mode is what we currently do when performing
Rx. As I make further changes what should happen is that the driver will
fall back to the behavior for Rx as of this patch should the "legacy-rx"
flag be set to on.
Change-ID: I0342998849bbb31351cce05f6e182c99174e7751
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is meant to clean up the code in preparation for us adding
support for build_skb. Specifically we deconstruct i40e_fetch_buffer into
several functions so that those functions can later be reused when we add a
path for build_skb.
Specifically with this change we split out the code for adding a page to an
exiting skb.
Change-ID: Iab1efbab6b8b97cb60ab9fdd0be1d37a056a154d
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch pulls out the code responsible for handling buffer recycling and
page counting and distributes it through several functions. This allows us
to commonize the bits that handle either freeing or recycling the buffers.
As far as the page count tracking one change to the logic is that
pagecnt_bias is decremented as soon as we call i40e_get_rx_buffer. It is
then the responsibility of the function that pulls the data to either
increment the pagecnt_bias if the buffer can be recycled as-is, or to
update page_offset so that we are pointing at the correct location for
placement of the next buffer.
Change-ID: Ibac576360cb7f0b1627f2a993d13c1a8a2bf60af
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch pulls the code responsible for fetching the Rx buffer and
synchronizing DMA into a function, specifically called i40e_get_rx_buffer.
The general idea is to allow for better code reuse by pulling this out of
i40e_fetch_rx_buffer. We dropped a couple of prefetches since the time
between the prefetch being called and the data being accessed was too small
to be useful.
Change-ID: I4885fce4b2637dbedc8e16431169d23d3d7e79b9
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This change makes it so that we use the length of the packet instead of the
DD status bit to determine if a new descriptor is ready to be processed.
The obvious advantage is that it cuts down on reads as we don't really even
need the DD bit if going from a 0 to a non-zero value on size is enough to
inform us that the packet has been completed.
Change-ID: Iebdf9cdb36c454ef092df27199b92ad09c374231
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This flag hasn't been used since commit 1e1be8f622ee ("i40e: ATR policy
change to flush the table to clean stale ATR rules").
Lets simplify things and just remove it.
Change-ID: I76279d84db8a2fd96f445b96aa413059f9256879
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The goto found here for when in MFP mode is pointless. It jumps to the
end of a series of if blocks. However, right after this statement is
a closing '}' for this if block, which will result in the program flow
going to the exact same location as the goto statement indicates. Thus,
regardless of whether we are in MFP mode, the program flow will resume
from the same location.
This arose due to various refactoring which did not notice that this
goto became essentially a no-op.
To properly understand this diff you will need to view a larger context
than is given by default.
Change-ID: I088f73c3831aa5c4e2281380c7a3ce605594300c
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix a case where we miss an arq element if a new one is added before we
enable interrupts and exit the arq subtask loop. This occurs frequently
with RDMA running on Windows VF and causes long delays that prevent SMB
from establishing connections.
Change-ID: I3e1c8b2b960c12857d9b8275bea2c1563674392e
Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The XL722 doesn't support the AQ command to read/write the control
register so enable it to bypass the check and use the direct read/write
method.
Change-ID: Iefecc737b57207485c90845af5989d5af518bf16
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch cleans up and addresses several issues in the way that i40e
handles private flags. Previously the code was choosing fixed bits and
trying to match them up with strings in a somewhat haphazard way. This
resulted in the possibility for adding a new bit and causing a mismatch as
the private flags are linear bits starting at 0, and the private flags in
the driver were split up over a group specific to the PF and a group that
was global.
What this change does is define an array of structs used to represent the
private flags. Contained within the structs are the bits necessary to know
which flags to set and/or clear depending on the state of the bit. By
doing this we can add new bits in the future with minimal overhead and
avoid creating possible mis-matches should we need to remove a flag based
on compile options.
Change-ID: Ia3214ab04f0ab2f70354ac0997a135f1d01b0acd
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The current driver mode is to use a write-back mechanism for the head
register which indicates transmit completions. The VF driver needs to be
able to work on hardware that exclusively uses descriptor write-back, so
change the default driver mode of operation to descriptor write-back for
VF. In our analysis, performance wasn't significantly different with
either write-back method.
Change-ID: Ia92e4ec77c2df8dc4515c71d53746d57d77759af
Signed-off-by: Preethi Banala <preethi.banala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This message just fills up dmesg and/or kernel logs and does
not provide any useful information.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There is an include loop between netdevice.h, dsa.h, devlink.h because
of NETDEV_ALIGN, making it impossible to use devlink structures in
dsa.h.
Break this loop by taking dsa.h out of netdevice.h, add a forward
declaration of dsa_switch_tree and netdev_set_default_ethtool_ops()
function, which is what netdevice.h requires.
No longer having dsa.h in netdevice.h means the includes in dsa.h no
longer get included. This breaks a few other files which depend on
these includes. Add these directly in the affected file.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom FlexRM mailbox driver uses platform MSI support but
not all ARCHs provide asm/msi.h. Due to this, we get compilation
error in Broadcom FlexRM mailbox driver via linux/msi.h on ARCHs
which lack asm/msi.h.
This patch removes "depends on COMPILE_TEST" for Kconfig option
BCM_FLEXRM_MBOX so that Broadcom FlexRM mailbox driver is only
compiled for ARM64.
Signed-off-by: Anup Patel <anup.patel@broadcom.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
|
|
Refactor interrupt moderation code for flexibility because parameters are
different for 10G and 25G cards. Currently parameters (for 10G only) come
from macros compiled-in to the PF and VF drivers; fix it so that parameters
suitable for the card (10G or 25G) come from the NIC firmware via response
to a command.
Also bump up driver version to 1.5.1 to match newer NIC firmware version.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I do not hold the copyright of the DSA core and drivers source files,
since these changes have been written as an initiative of my day job.
Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the trunk member of the mv88e6xxx_atu_entry structure regardless its
value, so that uninitialized structures gets the correct boolean value.
Note that no mainline code is affected by the current behavior.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't support 88E6391 anywhere in the code, so remove the unused
mv88e6391_ops structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6xxx_info structure for the 88E6191 chip was pointing the
mv88e6391_ops definition instead of mv88e6191_ops. Fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The related mv88e6xxx_ops structure was misplaced. Reorder it correctly
to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The related mv88e6xxx_ops and mv88e6xxx_info structure were misplaced.
Reorder them correctly to fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-7 reports a warning that earlier versions did not have:
drivers/net/ethernet/rocker/rocker_ofdpa.c: In function 'ofdpa_port_stp_update':
arch/x86/include/asm/string_32.h:79:22: error: '*((void *)&prev_ctrls+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
*((short *)to + 2) = *((short *)from + 2);
~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/rocker/rocker_ofdpa.c:2218:7: note: '*((void *)&prev_ctrls+4)' was declared here
This is clearly a variation of the warning about 'prev_state' that
was shut up using uninitialized_var().
We can slightly simplify the code and get rid of the warning by unconditionally
saving the prev_state and prev_ctrls variables. The inlined memcpy is not
particularly expensive here, as it just has to read five bytes from one or
two cache lines.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In NETDEV_CHANGEUPPER event the upper_info field is valid
only when linking is true. Otherwise it should be ignored.
Fixes: 7907f23adc18 (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, qed used some port-defined value as BDQ index for both iSCSI
and FCoE.
As management firmware now treats BDQ as a resource and tells each PF
its BDQ-range, start using a valure from that range instead.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Management firmware is used as an arbiter between the various PFs
in matters of resources, but some of the resources that need to
be divided are dependent on the non-management firmware used,
so management firmware first needs to be told how many resources
there are before trying to divide them.
As part of the initialization sequence, driver would first inform
the management firmware of the available resources under
a dedicated resource lock, and afterwards request for various
resources which might be based on the previous set values.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Global locking can't properly be used to synchronize between different
PFs in all scenarios, as those instances might reside in different
logical partitions [e.g., when a PF is assigned via PDA to some VM].
The management firmware provides a generic infrastructure for
device locks. For each 'resource', it's guaranteed it could be acquired
by at most a single PF at any given time [or by management firmware].
This patch adds the necessary logic in qed for utilizing said
infrastructure, implementing lock/unlock internal APIs.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During HW initialization, driver would set various registers to their
needed values - but it assumes all registers start at their reset-value,
so there's no need to re-configure a register's default value.
This assumption might be incorrect, e.g., in case of preboot driver
running and initializing the driver prior to our driver.
To overcome this, we now ask management firmware to initiate a PF-flr
early during the initialization sequence. That would return everything
in the PF's scope back to default and prevent previous configurations
from still being applied.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Management firmware is used as an arbiter between the various PFs
in regard to loading - it causes the various PFs to load/unload
sequentially and informs each of its appropriate rule in the init.
But the existing flow is too weak to handle some scenarios where
PFs aren't properly cleaned prior to loading.
The significant scenarios falling under this criteria:
a. Preboot drivers in some environment can't properly unload.
b. Unexpected driver replacement [kdump, PDA].
Modern management firmware supports a more intricate loading flow,
where the driver has the ability to overcome previous limitations.
This moves qed into using this newer scheme.
Notice new scheme is backward compatible, so new drivers would
still be able to load properly on top of older management firmwares
and vice versa.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We'll soon need additional information, so start by changing
the infrastructure to receive the initializing variables
via a parameter struct.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Management firmware is used as arbiter between different PFs
which are loading/unloading, but in order to use the synchronization
it offers the contending configurations need to be applied either
between their LOAD_REQ <-> LOAD_DONE or UNLOAD_REQ <-> UNLOAD_DONE
management firmware commands.
Existing HW stop flow utilizes 2 different functions: qed_hw_stop() and
qed_hw_reset() which don't abide this requirement; Most of the closure
is doing outside the scope of the unload request.
This patch removes qed_hw_reset() and places the relevant stop
functionality underneath the management firmware protection.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
moxart_mac_start_xmit() doesn't care where tx_tail is, tx_head can
catch and pass tx_tail, which is bad because moxart_tx_finished()
isn't guaranteed to catch up on freeing resources from tx_tail.
Add a check in moxart_mac_start_xmit() stopping the queue at the
end of the circular buffer. Also add a check in moxart_tx_finished()
waking the queue if the buffer has TX_WAKE_THRESHOLD or more
free descriptors.
While we're at it, move spin_lock_irq() to happen before our
descriptor pointer is assigned in moxart_mac_start_xmit().
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=99451
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A driver must not access the two fields directly but should instead use
the helper functions to set the values and keep a consistent internal
state:
ethernet/stmicro/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
ethernet/stmicro/stmmac/stmmac_main.c:4083:8: error: 'struct net_device' has no member named 'real_num_rx_queues'; did you mean 'real_num_tx_queues'?
Fixes: a8f5102af2a7 ("net: stmmac: TX and RX queue priority configuration")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-7 points out that the AVMB1_ADDCARD ioctl results in an unintialized
value ending up in the cardnr parameter:
drivers/isdn/capi/kcapi.c: In function 'old_capi_manufacturer':
drivers/isdn/capi/kcapi.c:1042:24: error: 'cdef.cardnr' may be used uninitialized in this function [-Werror=maybe-uninitialized]
cparams.cardnr = cdef.cardnr;
This has been broken since before the start of the git history, so
either the value is not used for anything important, or the ioctl
command doesn't get called in practice.
Setting the cardnr to zero avoids the warning and makes sure
we have consistent behavior.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the RPM driver transitioned to RPMSG we can reuse the SMD-RPM
driver ontop of GLINK for 8996, without any modifications.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the standalone SMD implementation as we have transitioned the
client drivers to use the RPMSG based one.
Also remove all dependencies on QCOM_SMD from Kconfig files, in order to
keep them selectable in the absence of the removed symbol.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By moving these client drivers to use RPMSG instead of the direct SMD
API we can reuse them ontop of the newly added GLINK wire-protocol
support found in the 820 and 835 Qualcomm platforms.
As the new (RPMSG-based) and old SMD implementations are mutually
exclusive we have to change all client drivers in one commit, to make
sure we have a working system before and after this transition.
Acked-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vxlan driver already implicitly supports installing
of external fdb entries with NTF_EXT_LEARNED. This
patch just makes sure these entries are not aged
by the vxlan driver. An external entity managing these
entries will age them out. This is consistent with
the use of NTF_EXT_LEARNED in the bridge driver.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement dpipe's table ops for erif table which provide:
1. Getting the entries in the table with the associate values.
- match on "mlxsw_meta:erif_index"
- action on "mlxsw_meta:forwared_out"
2. Synchronize the hardware in case of enabling/disabling counters which
mean removing erif counters from all interfaces.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add rif helper function to access the rif index and rif devices ifindex.
This functions will be used by dpipe in order to dump the rif table.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for counter allocation on router interfaces. The allocation
depends on the counter state of relevant table. In case the counting is
disabled or no counters left the counter index will be set as invalid.
Also a counter pool for router allocation is added.
Signed-off-by: Arakdi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RICNT register retrieves per port performance counter. It will be
used to query the router interfaces statistics.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add definition for egress router interface table. This table describes
the final part in the routing pipeline. This table matches the egress
interface index (rif index, which is set by the previous stages and
determine the out port) and makes the decision of forwarding the packet
towards the L2 logic or dropping it.
The metadata header is added to represent this internal information.
The rif index field is mapped logically to netdevice ifindex.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add placeholder for dpipe. Support for specific tables and headers will
be introduced in following patches. The headers are shared between all
mlxsw_sp instances.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update RITR for counter support. This allows adding counters for
ASIC's router ports.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The various properties associated with powernv idle states such as
names, flags, residency-ns, latencies-ns, psscr, psscr-mask are
exposed in the device-tree as property arrays such the pointwise
entries in each of these arrays correspond to the properties of the
same idle state.
This patch validates that the lengths of the property arrays are the
same. If there is a mismatch, the patch will ensure that we bail out
and not expose the platform idle states via cpuidle.
Signed-off-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com>
Reviewed-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When an IRQ safe device is attached to a no sleep domain, genpd prints a
warning once, as to indicate it is a suboptimal configuration from power
consumption point of view.
However the warning doesn't make sense for an always on domain, since it
anyway remains powered on. Therefore, let's change to not print the warning
for this configuration.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
